Renesas H8S/2615 Series User's Manual
Contents
1. Section 5 Notice Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket The dimensions of the recommended mount pad for the user system IC socket are different from those of the MCU This user system interface cable is specifically designed for the HS2628EPI61H emulator Do not use this cable with any other emulator station To prevent breaking of wires in the cable body do not place heavy or sharp metal objects on the user system interface cable While the emulator station is connected to the user system with the user system interface cable force must not be applied to the cable head Place the emulator station user system interface cable and user system as shown in the example in figure 10 Place components so that the cable body and cable head are parallel to the user system Emulator station Cable head is parallel F to emulator station _l TRA Cable head is parallel to user system User system PE Figure 10 User System Interface Cable Location Example 6 The P1 short connector is used for testing Do not remove the jumper pin that is inserted in the side of pin1 and pin2 B SW2 AB SWI A Figure 11 P1 Short Connector 15 RENESAS2. 2 3 Recommended Dimensions for User System Mount Pad Figure 5 shows the recommended dimensions for the mount pad footprint for the user system with an IC socket for an FP 80Q package IC149 080 017 B5 manufactured by YAMAICHI ELECTRONICS Co Ltd Note that the dimensions in figure 5 are somewhat different from those of the actual chip s mount pad pr 20 50 min gt ent 14 70 max gt p 0 65 x 19 12 35 0 1 gt 0 1 0 65 0 05 0 35 79 05 m t V S55 gt A m m Cc Lo 2 o LO i Lo o Q o Il g x lt LO Oo m m a a m y co a Figure 5 Recommended Dimensions for Mount Pad RENESAS 2 4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 6 63 5 63 5 Unit mm Tolerance 0 5 mm Figure 6 Dimensions for User System Interface Cable Head 10 RENESAS 2 5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions after connecting the user system interface cable head to the user system are shown in figure 7 21 5 Cable head gt OO EO 9 4 i IC socket IC149 080 017 B5 Unit mm manufactured by Tolerance 0 5 mm YAMAICHI ELECTRONICS Co Ltd User system Figure 7 Resultin
3. A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage NOTE emphasizes essential information lt RENESAS AA WARNING Observe the precautions listed below Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST 1 Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance 2 Always switch OFF the E6000 emulator and user system before connecting or disconnecting any CABLES or PARTS 3 Always before connecting any CABLES make sure that pin 1 on both sides are correctly aligned RENESAS Cautions Renesas neither warrants nor grants licenses of any rights of Renesas s or any third party s patent copyright trademark or other intellectual property rights for information contained in this document Renesas bears no responsibility for problems that may arise with third party s rights including intellectual property rights in connection with use of the information contained in t
4. Mind 1 Circuitry and other examples described herein are meant merely to indicate the characteristics and performance of Renesas s semiconductor products Renesas assumes no responsibility for any intellectual property claims or other problems that may result from applications based on the examples described herein 2 No license is granted by implication or otherwise under any patents or other rights of any third party or Renesas Figures Some figures in this user s manual may show items different from your actual system Limited Anticipation of Danger Renesas cannot anticipate every possible circumstance that might involve a potential hazard The warnings in this user s manual and on the user system interface cable are therefore not all inclusive Therefore you must use the user system interface cable safely at your own risk Ill RENESAS SAFETY PAGE READ FIRST READ this user s manual before using this user system interface cable e KEEP the user s manual handy for future reference Do not attempt to use the user system interface cable until you fully understand its mechanism DEFINITION OF SIGNAL WORDS gt This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury
5. head The tightening torque must be 0 0785 Nem or less If the applied torque cannot be accurately measured stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening If a screw is tightened too much the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder If the emulator does not operate correctly cracks might have occurred in the solder Check conduction with a tester and re solder the IC socket if necessary RENESAS Fasten the user system interface cable head to the IC socket for an FP 80Q package on the user system with the four screws M2 x 12 mm with four flat washers provided Each screw should be tightened a little at a time alternating between screws on opposing corners Take special care such as manually securing the IC socket soldered area to prevent the soldered IC socket from being damaged by overtightening the screws or twisting the components Screws M2 x 12 mm with flat washers Cable head Pin 1 IC socket IC149 080 017 B5 manufactured by YAMAICHI ELECTRONICS Co Ltd User system Figure 3 Connecting User System Interface Cable to User System RENESAS 2 2 5 Fastening Cable Body Connect the cable body to the cable head Cable body ra Removing Push the remove jig User system Figure 4 Fastening Cable Body RENESAS
6. 4 Verifying Operation Turn on the emulator according to the procedures described in the H8S Series E6000 Emulator User s Manual HS2000EP161HE Verify the user system interface cable connections by accessing the external memory and ports to check the bus states of the pins with the MEMORY_FILL command emulator command If an error is detected recheck the soldered IC socket and the location of pin 1 The emulator connected to this user system interface cable supports two kinds of clock sources as the MCU clock an emulator internal clock and an external clock on the user system For details refer to the H8S Series E6000 Emulator Supplementary Information HS2628EPI61HE To use the emulator internal clock Select the clock in the emulator station as the system clock 6 by using the CLOCK command emulator command To use the external clock on the user system Select external clock Target or Target 2 with the CLOCK command emulator command Supply the external clock from the user system to the emulator by inputting the external clock from the EXTAL terminal on the cable head or connecting a crystal oscillator to the EXTAL and XTAL terminals For details refer to the Clock Pulse Generator section in the H8S 2615 Series Hardware Manual Figure 9 shows the oscillator circuit on the user system interface cable R1 1 MQ HCU04 To E6000 emulator R2 270 0 EXTAL XTAL Figure 9 Oscillator Circuit RENESAS
7. AS 2 2 Connecting User System Interface Cable to User System A WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part Before connecting make sure that pin 1 on both sides are correctly aligned Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST To connect the cable head to the user system follow the instructions below 2 2 1 Installing IC Socket After checking the location of pin 1 on the IC socket apply epoxy resin adhesive to the bottom of the IC socket for an FP 80Q package and fasten it to the user system before soldering 2 2 2 Soldering IC Socket After fastening solder the IC socket for an FP 80Q package to the user system Be sure to completely solder the leads so that the solder slops gently over the leads and forms solder fillets Use slightly more solder than the MCU RENESAS 2 2 3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting Align pin 1 on the IC socket for an FP 80Q package on the user system with pin 1 on the user system interface cable head and insert the user system interface cable head into the IC socket on the user system as shown in figure 3 2 2 4 Fastening Cable Head CAUTION Use a Philips type screwdriver whose head matches the screw
8. CONSEQUENTIAL DAMAGES OF ANY NATURE OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE USER SYSTEM INTERFACE CABLE THE USE OF ANY USER SYSTEM INTERFACE CABLE OR ITS DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES EXCEPT AS EXPRESSLY STATED OTHERWISE IN THIS WARRANTY THIS USER SYSTEM INTERFACE CABLE IS SOLD AS IS AND YOU MUST ASSUME ALL RISK FOR THE USE AND RESULTS OBTAINED FROM THE USER SYSTEM INTERFACE CABLE RENESAS State Law Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may have other rights which may vary from state to state The Warranty is Void in the Following Cases Renesas shall have no liability or legal responsibility for any problems caused by misuse abuse misapplication neglect improper handling installation repair or modifications of the user system interface cable without Renesas s prior written consent or any problems caused by the user system All Rights Reserved This user s manual and user system interface cable are copyrighted and all rights are reserved by Renesas No part of this user s manual all or part may be reproduced or duplicated in any form in hard copy or machine readable form by any means available without Renesas s prior written consent Other Important Things to Keep in
9. H8S 2615 Series FP 80Q User System Interface Cable HS2615ECH61H for E6000 Emulator User s Manual rCENESAS HS2615ECH61HE IMPORTANT INFORMATION READ FIRST READ this user s manual before using this user system interface cable KEEP the user s manual handy for future reference Do not attempt to use the user system interface cable until you fully understand its mechanism User System Interface Cable Throughout this document the term user system interface cable shall be defined as the following product produced only by Renesas Technology Corp excluding all subsidiary products e User system interface cable HS2615ECH61H The user system or a host computer is not included in this definition Purpose of the User System Interface Cable This user system interface cable is for connecting the emulator station and user system This user system interface cable must only be used for the above purpose Improvement Policy Renesas Technology Corp including its subsidiaries hereafter collectively referred to as Renesas pursues a policy of continuing improvement in design performance functions and safety of the user system interface cable Renesas reserves the right to change wholly or partially the specifications design user s manual and other documentation at any time without notice Target User of the User System Interface Cable This user system interface cable should only be used by those who have carefully
10. e or part of this document without written approval from Renesas Contact Renesas s sales office for any questions regarding this document or Renesas semiconductor products Preface Thank you for purchasing this user system interface cable HS2615ECH61H for the Renesas s original microcomputer H8S 2615 series The HS2615ECH61H is a user system interface cable that connects an H8S 2615 series E6000 emulator HS2612EPI61H hereinafter referred to as the emulator to the IC socket for a FP 80Q package for the H8S 2615 series MCU on the user system RENESAS Contents Section 1 Configuration si2 secessdvsaneniedeatenedseinande cucuanedcespeque dontancd tabnasceaonescadenteete 1 Section 2 Connection Procedures lt lt c ssasisssvondenscsssesanastsascnteteestentossssecsendonaotoadects 3 2 1 Connecting User System Interface Cable to Emulator Station 0 0 eee eeeeseereeeeereeeeeee 3 2 2 Connecting User System Interface Cable to User System W GWu u u ssensrsererereeserenseee nere 5 221 Installing IC Socket saae NERE 5 2 2 2 Solderns IC Socket sunnier NEEE eK TEETER iie 5 2 2 3 Inserting Cable Head siicnssccasceaiscssites svabsvanssievenesonbesdessiscdeconasndsaredscancoasesseeevecizens 6 2 24 Bastening Cable Head csce cciesst svssssisehevles stssusibsesssivnsts s enon arr Eei 6 2 2 3 Fastening Cable Body csiscscitacssuscess sisstecepscvnaosesasscateies sbaetecobedtenstenstdanepedanebeerbaons 8 2 3 Recommended Dimensions f
11. flat washers 6 Screws M2 x 8 mm 4 For installing an FP 80Q packaged MCU with four flat washers 7 Documentation 1 User s manual for HS2615ECH61H this manual 2 RENESAS Section 2 Connection Procedures 2 1 Connecting User System Interface Cable to Emulator Station MA WARNING Observe the precautions listed below Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST 1 Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part Before connecting make sure that pin 1 on both sides are correctly aligned The user system interface cable dedicated to the emulator must be used To connect the cable body to the emulator station follow the instructions below 1 Make sure the user system and emulator station are turned off CAUTION When connecting or removing the user system interface cable apply force only in the direction suitable for connection or removal while making sure not to bend or twist the cable or connectors Otherwise the connectors will be damaged 2 After making sure the direction of the cable body connector is correct firmly insert the cable body connector into the emulator station socket figure 2 RENESAS Figure 2 Connecting User System Interface Cable to Emulator Station RENES
12. g Dimensions after Connecting User System Interface Cable 11 rRENESAS Section 3 Installing the MCU to the User System CAUTION Check the location of pin 1 before inserting Use a Philips type screwdriver whose head matches the screw head The tightening torque must be 0 0785 N m or less If the applied torque cannot be accurately measured stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening If a screw is tightened too much the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder If the MCU does not operate correctly cracks might have occurred in the solder Check conduction with a tester and re solder the IC socket if necessary Check the location of pin before inserting the MCU into the IC socket on the user system as shown in figure 8 After inserting the MCU fasten the socket cover with the provided four screws M2 x 8 mm with four flat washers Take special care such as manually securing the IC socket soldered area to prevent the IC socket from being damaged by overtightening the screws or twisting the components RENESAS Screws M2 x 8 mm with flat washers MCU Pin 1 IC socket 4 IC149 080 017 B5 manufactured by YAMAICHI ELECTRONICS Co Ltd User system Figure 8 Installing MCU to User System RENESAS 1 Section
13. his document Products and product specifications may be subject to change without notice Confirm that you have received the latest product standards or specifications before final design purchase or use Renesas makes every attempt to ensure that its products are of high quality and reliability However contact Renesas s sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury such as aerospace aeronautics nuclear power combustion control transportation traffic safety equipment or medical equipment for life support Design your application so that the product is used within the ranges guaranteed by Renesas particularly for maximum rating operating supply voltage range heat radiation characteristics installation conditions and other characteristics Renesas bears no responsibility for failure or damage when used beyond the guaranteed ranges Even within the guaranteed ranges consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as fail safes so that the equipment incorporating Renesas product does not cause bodily injury fire or other consequential damage due to operation of the Renesas product This product is not designed to be radiation resistant No one is permitted to reproduce or duplicate in any form the whol
14. or User System Mount Pad cc ceeecesesceeeeceeeeeeeeeeeeeens 9 2 4 Dimensions for User System Interface Cable Head ei eeeeeeeeecseeeeceseeeceaeeeeeseeeeeeeens 10 2 5 Resulting Dimensions after Connecting User System Interface Cable eee eee 11 Section 3 Installing the MCU to the User System ee eeeeeeseeeteeeneetees 12 Section 4 Verifying Operations s sssssccvssviseisessasassandicedsalieneasabazencsasdaszevasvesncosnseee 14 Section D Notice sorgen ere ennen 15 ii RENESAS Section 1 Configuration CAUTION Use an IC149 080 017 B5 socket manufactured by YAMAICHI ELECTRONICS Co Ltd for the FP 80Q package IC socket on the user system Figure 1 shows the configuration of the HS2615ECH61H user system interface cable for the FP 80Q package To emulator station Screws M2 x 12 mm ith flat washers Screws M2 x 8 mm Wit with flat washers g for fastening cable head T f Socket cover Cable head DS IC socket User system Figure 1 HS2615ECH61H User System Interface Cable RENESAS Table 1 lists the HS2615ECH61H components Please make sure you have all of these components when unpacking Table 1 HS2615ECH61H Components No Component Quantity Remarks 1 Cable body 1 Flat cable 2 Cable head 1 3 IC socket 1 For the FP 80Q package 4 Socket cover 1 For installing an FP 80Q packaged MCU 5 Screws M2 x 12 mm 4 For fastening cable head with four
15. read and thoroughly understood the information and restrictions contained in the user s manual Do not attempt to use the user system interface cable until you fully understand its mechanism It is highly recommended that first time users be instructed by users that are well versed in the operation of the user system interface cable RENESAS LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and free from defects in material and or workmanship Renesas will repair or replace any user system interface cables determined to be defective in material and or workmanship User system interface cables are wearing parts which Renesas will not repair or replace if damaged and or worn through use The foregoing shall constitute the sole remedy for any breach of Renesas s warranty This warranty extends only to you the original Purchaser It is not transferable to anyone who subsequently purchases the user system interface cable from you Renesas is not liable for any claim made by a third party or made by you for a third party DISCLAIMER RENESAS MAKES NO WARRANTIES EITHER EXPRESS OR IMPLIED ORAL OR WRITTEN EXCEPT AS PROVIDED HEREIN INCLUDING WITHOUT LIMITATION THEREOF WARRANTIES AS TO MARKETABILITY MERCHANTABILITY FITNESS FOR ANY PARTICULAR PURPOSE OR USE OR AGAINST INFRINGEMENT OF ANY PATENT IN NO EVENT SHALL RENESAS BE LIABLE FOR ANY DIRECT INCIDENTAL OR
Download Pdf Manuals
Related Search