RCA MST46BKR User's Manual
Contents
1. of supporting the combined weight of the mount and display 1 Use a high quality stud finder to locate two adjacent studs where you wish to install your mount Mark both edges of each stud to help identify the exact center NOTE You must use the center of each stud to avoid cracking or splitting the wood during installation 2 Place the mounting template against the wall over the center line of the marked studs Make sure the template is level 3 Drill four 3 mm 1 8 pilot holes in the wall using the template as a guide Drill two holes per stud see Fig 2 4 Remove the template from the wall and place the assembled wall plate against the wall over the pilot holes 5 Attach the wall plate to the wall using the M6 3 x 63 screws A and washers B provided see Fig 3 Do not over tighten these the mount until all screws are in place Ensure after all screws are secured Part 1B Mounting to the Wall Concrete IMPORTANT For safety reasons the concrete wall must be capable of supporting the combined weight of the mount and the display The manufacturer takes no responsibility for failure caused by walls of insufficient strength 1 Place the mounting template against the wall in the desired location Make sure the template is level 2 Drill four 8 mm 5 16 holes in the wall using the template as a guide Remove any excess dust from the holes see Fig 4 3 Remove the template from the wall and inser2. d has a pro to use the longer screws E G or and may al ing holes are flush with the surface you will use the shorter rusion or if the mounting holes are recessed you will need Iso need to use the spacers k 2 Determine the correct diameter of screw to use by carefully trying one of each size M4 M6 and M8 from the hardware kit Do not force any of the screws if you feel resistance stop immediately and try a smaller diameter screw Continues on next page 3 Attach the mount arms to the back of your display using the screws identified in steps 1 and 2 see Fig 6 For displays with curved or recessed A If you are using the M4 or M6 screws you will also need to use the M6 washers J M8 screws do not require washers B If you are using the longer screws on a display with a curved or recessed back you may also need to use the spacers K Use one spacer or two spacers stacked as needed Only use a spacer if necessary NOTE Make sure the mount arms are attached with the tilt mechanisms facing outward exactly as shown in the illustration see Fig 7 Otherwise the tilt function cannot be accessed Tilt Adjustment y Tilt Adjustment Mechanism Mechanism Part 3 Final Assembly 1 2 If the plastic tabs hang below the bottom of your display they can be trimmed If you need to remove the display from the mount pull the plastic tabs located Check to make
3. e under any circumstances 6 Follow all instructions and recommendations regarding adequate ventilation and suitable locations for mounting your display Consult the owner s manual for your particular display for more information Pour des instructions en frangais se reporter a la page 6 Para obtener instrucciones en espa ol consulte la pagina 11 Continues on next page Tools required Phillips Head Screwdriver or Screw Gun Electric or Portable Drill 3 mm 1 8 Drill Bit and Stud Finder for Drywall Installation 8 mm 5 16 Masonry Bit for Concrete Installation Level Hardware kit A M6 3 x 63 Lag Bolt x4 mmm H M8 x 12 Screw x4 B Washer x4 I M8 x 30 Screw x4 C Concrete Anchor x4 J M6 Washer x4 D M4 x 12 Screw x4 K Spacer x8 E M4 x 20 Screw x4 L Long Allen Key x1 F M6 x 12 Screw x4 um M 3 16 Drill Bit G M6 x 30 Screw x4 7 Assembly Assemble the mount by carefully snapping the right and left plastic sides onto the upper and lower wall plates as shown in the illustration see Fig 1 Do not force any of the connections as it may result in breakage of the plastic parts Installation Part 1A Mounting to the Wall Drywall IMPORTANT For safety reasons this mount must be secured to at least two wood studs no less than 16 apart The studs must be capable
4. flat panel solutions MST46BKR Tilt Wall Mount for LCD Plasma and Fits TVs 26 46 LED Displays Maximum Load Capacity 99 Ib 45 kg Instruction Manual Specifications Display Size 26 to 46 Maximum Load 99lb 45kg Mounting Pattern 400 mm x 400 mm 15 7 x 15 7 max Tilt Range 15 down Profile 1 4 3 5cm Box contents Upper Wall Plate x1 Mount Arm x2 Lower Wall Plate x1 Instruction Manual x1 Left Plastic Side x1 Hardware Kit x1 Right Plastic Side x1 Template x1 Warnings 1 Read these instructions before you begin If A CAUTION you are unsure of any part of the process contact 2 i a professional contractor or installer for assistance This wall mount is intended for use only with the Improper installation can result in injury or damage maximum weight of 45 kg 99 Ibs Use with heavier than the maximum weights indicated may result in 2 The wall or mounting surface must be capable of instability causing possible injury supporting the combined weight of the mount and the display if not the structure must be reinforced 3 Locate pipes wires or any other hazards in the wall where you wish to install the mount before drilling 4 Safety gear and proper tools must be used Failure to do so can result in injury or damage 5 A minimum of two people are required for installation Do not attempt to install this mount alon
5. ome loose over time Re tighten as needed
6. sure the tilt mechanism is fully tightened It can be tightened using the long Allen key L provided in the hardware kit With the help of another person carefully lift your display and place it on the mount Do not release the display until the mount arms have securely hooked onto the mount Make sure the safety locks have successfully engaged by gently pushing up on the display You should not be able to remove the display from the mount with a knife or looped back and tucked into the rubber ring located on each tab at the bottom of the mount arms down and then forward away from the wall to engage the tooth and disengage the safety locks see Fig 8 With the help of another person carefully lift the display from the mount Return the tabs to their original position by pulling them down and pushing them backwards Operation and adjustment 1 To change the tilt angle of your display hold the display firmly in place and loosen the tilt mechanisms using the long Allen key L from the hardware kit see Fig 9 Move your display to the desired position and then re tighten the tilt mechanisms If your display is in the non tilt position you will need to push up gently on the display before you can move it Do not release the display until both tilt mechanisms are firmly tightened 2 Periodically clean your mount with a dry cloth Inspect all screws and hardware at regular intervals to ensure that no connections have bec
7. t a concrete anchor C into each hole so that it is flush with the concrete surface see Fig 5 A hammer can be used to lightly tap the anchors into place if necessary NOTE If the concrete wall is covered by a layer of plaster or drywall the concrete anchor must pass completely through the layer to rest flush with the concrete surface 4 Place the assembled wall plate against the wall over the inserted anchors and attach it using the M6 3 x 63 screws A and washers B provided see Fig 3 Do not over tighten these screws and do not release the mount until all screws and do not release that the mount remains level screws are in place Ensure that the mount remains level after all screws are secured Part 2 Attaching the Mount Arms to the Display IMPORTANT Use extra care during this part of the installation If possible avoid placing your display facedown as it may damage the viewing surface NOTE This mount comes with a selection of different of display models Not all of the hardware in the kit wil kit provided consult the manufacturer of your display screw diameters and lengths to accommodate a wide variety be used If you cannot find the appropriate screw size in the or more information 1 Determine the correct length of screw to use by examining the back of your display A If the back of your display is flat and the moun screws D F or H from the hardware kit B If the back of your display is curve
Download Pdf Manuals
Related Search