RCA 2130-0BKGA User's Guide
Contents
1. Parts Checklist Make sure your package includes the items listed here Handset ame a battery cells AC power attery adaptor Charge cradle compartment p cover Handset Installing the Phone Fit the rechargeable batteries in each handset 1 Install the AAA batteries Brand name CORUN Capacity Ni MH 1 2V 550mAh or Brand name SANIK Capacity Ni MH 1 2V 550mAh into handset in accordance with the polarity marked in the battery compartment 2 Close the battery compartment cover sliding it into place and pressing firmly to make sure it is secure Connecting AC electrical power 1 Plug the base power adaptor Type IA1560 120Vac 6Vdc 500mA cord into the power jack on rear panel of the charging pod 7 Before you use the cordless handset for the first time it s important to charge the batteries fully Leave the handset on the charging cradle for 16 hours The battery charge symbol will blink when you re charging an empty battery If you think that the symbol isn t showing the correct battery charge level first check that the handset is correctly positioned in the charging cradle If you re sure that it is remove and refit the batteries Please note that it s normal for the main adaptor to become warm this doesn t indicate a fault CAUTION Use only the power supply that came with this unit Using other power supplies may damage the unit Charge adaptor is 1A1560 120Vac 6Vdc 150mA Advanced Set 12. Quick Set up Guide for Optional Additional Model 2130 DECT 6 0 Cordless Handset for use with Systems 2131 and 2132 series Please read this manual before operating product for the first time Visit the RCA web site at www rca4phones com Model 2130 Equipment Approval Information Your telephone equipment is approved for connection to the Public Switched Telephone Network andis in compliance with parts 15 and 68 FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA 1 Notification to the Local Telephone Company On the bottom of this equipment is a label indicating among other information the US number and Ringer Equivalence Number REN for the equipment You must upon request provide this information to your telephone company The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these devices ring when your telephone number is called In most but not all areas the sum of the RENs of all devices connected to one line should not exceed 5 To be certain of the number of devices you may connect to your line as determined by the REN you should contact your local telephone company A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA A compliant telephone cord and modular plug is provid
3. Make sure the phone is OFF not in TALK SPEAKER mode 2 Press the MENU OK button to go to main menu 3 Press the Navigation or button to select Advanced Set 4 Press the MENU OK button to access the setting menu Registration From the Advanced Set sub menu 1 Press the Navigation or button to scroll to the Registration 2 Press the MENU OK button to access registration setting the display will show Enter PIN 3 Use the touch tone pad to enter the 4 digits of PIN code default PIN code is 0000 4 Press the MENU OK button to confirm the screen displays Registering Press and hold the FIND button on the base for a few seconds You will hear a long confirmation tone if the registration is successful enter the handset number you want to arrange Oa De register the handset You may need to do this in order to replace a faulty handset From the Advanced Set sub menu 1 Press the Navigation or button to scroll to Unregister 2 Press the MENU OK button to access de register setting the screen display Enter PIN 3 Use the touch tone pad to enter the 4 digits of PIN code default PIN code is 0000 Enter the handset number to be de registered You will hear a long confirmation tone if the de registration is successful The screen display Unregistered af Programming Functions The system uses a menu structure to give you access to all of the built in features You may program the
4. PARTS INSIDE REFER SERVICING TO HAZARD DO NOT z S QUALIFIED SERVICE EXPOSETHIS z PERSONNEL PRODUCT TO RAIN THE PRODUCT THE PRODUCT OR MOISTURE SEE MARKING ON BOTTOM BACK OF PRODUCT Table of Contents Equipment Approval Information 2 Interference Information s s s Hearing Aid Compatibility HAC FCC RF Radiation Exposure Statement sessen Information for DECT Product Table of Contents Table of Contents INGFOCDUCTION crinsrinsiinss Before You Begin uu Installing the Phone Advanced Set Registration De register the handset Programming Functions Personal setting Handset tone Ring volume Ring melody Auto answer Auto hang up Language Using multi ities E E E A EEEE 11 Transfer an external call 12 Making conference call three way CONVErSATION 0 sees 2 Changing the Battery 3 Battery Safety Precautions 13 Troubleshooting 1 Warranty Assistance 7 Limited Warranty ou Introduction CAUTION When using telephone equipment there are basic safety instructions that should always be followed Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference IMPORTANT Because cordless phones operate on electricity you should have at least one phone in your home that isn t cordless in case the power in your home goes out Before You Begin
5. can TALK SPEAKER and listen simultaneously 1 During an external call press the INT button on the handset the external call is put on hold and the registered handset shows on the display enter the handset number you want to page 2 Wait until the internal user answers 3 Press and hold the INT button on original handset to start a three way conference call 12 4 When finished press the HANG UP button to end the conversation Changing the Battery CAUTION To reduce the risk of fire or personal injury use only the approved Nickel metal Hydride battery Ni MH which is compatible with this unit 1 Make sure the telephone is OFF not in TALK mode before you replace the battery 2 Remove the battery compartment door 3 Disconnect the cord attached to the battery pack and remove the battery pack from the handset 4 Insert the new battery pack and connect the cord to the jack inside the battery compartment 5 Put the battery compartment door back on 6 Place handset in the base to charge Allow the handset battery to properly charge for 16 hours prior to first use or when you install a new battery pack If you do not properly charge the phone battery performance will be compromised Battery Safety Precautions e Donotburn disassemble mutilate or puncture Like other batteries of this type toxic materials could be released which can cause injury e Toreduce the risk of fire or personal injury use only the Nic
6. computer You ll get the best sound if you place the base unit as high as possible For example ina two story house the first floor landing is an ideal place You may be going out of range of the base unit Move closer or your call may be cut off Check the Battery Level symbol on the display If it s low recharge the batteries In order to utilize the Caller ID features of this phone you will need to subscribe to Caller ID with your Telephone service provider Please contact your Telephone service provider for details The caller may have BLOCKED their number or the caller may be calling from a network that does not transmit the Caller ID data Allow at least 2 rings for the Caller ID data to display 15 When I try to make a call hear a busy tone If you re using a multi handset system check whether another handset is already ona call The volume in the earpiece is low when l m on a call Make sure you re holding the earpiece correctly over your ear Adjust the volume using the navigation key Intercom and transfer can t transfer a call Battery Make sure the other handset is in range of the base unit Make sure you are dialing the correct number for the other handset The handset s battery pack is running low within an hour or two Before you first use the handset you should have left it on the base unit or charger pod for 16 hours to charge t
7. not in talk mode 2 Press INT button on handset the Int symbol appears and the registered handsets shows on the display enter the handset number you want to page 3 The cordless handset rings and the Int symbol flashes on handset display When the handset user answers you will be connected Answering an intercom call The ringing tune for intercom calls is different from external calls When someone makes an intercom call to you Int icon appears on your cordless handset s display with the number of the handset calling you 1 Press the TALK SPEAKER button to answer 2 Toend anintercom call press the HANG UP button or place the handset in the base cradle Transfer an external call You can transfer an external call to another handset that is registered to the base station 1 During an external call press the INT button the external call is put on hold and the registered handset shows on the display 2 Enter the handset number you want to page 3 When the receiving handset answers you can announce the call 4 Press the HANG UP button on the original handset to transfer the call NOTE If the receiving handset does not answer within 30 seconds the external call will come back to you and your handset will ring You can press the TALK SPEAKER button to take the external call again Making conference call three way conversation You can connect one external call to two handsets registered at the base station All users
8. with you and please have your model number and date code available when calling us The model number and date code can be found on the underside of the base unit If you are within your limited warranty period and it is determined that service is required We will ask that you properly pack your product to avoid shipping damage We recommend that you use the original carton and packing materials We will ask you to include with your product the following Your name return shipping address and daytime phone number handwritten or typed on a sheet of paper A legible copy of your sales receipt please do not send the original sales receipt Ship your product prepaid to the address we provide We suggest shipping your product via a traceable carrier as we are not responsible for lost mis directed or damaged shipments You may want to write the date shipped carrier and tracking number here Upon receipt of your product we will validate your product is under warranty and if determined your product is warranty eligible we will ship to you a newor at our option a refurbished exchange unit of same or similar model This exchange unit will be shipped to you at no cost What your limited warranty does not cover Customer Instruction Your Owner s Manual provides information regarding operating and installation instructions Additional information may be obtained by contacting the retailer Installation and set up service
9. adjustments Batteries Damage from misuse neglect unauthorized repair Products which have been modified or incorporated into other products 18 Products that have been serviced by an unauthorized servicer Products purchased or serviced outside the USA or Canada Acts of nature such as but not limited to lightning damage Limitation of Warranty THIS LIMITED WARRANTY IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ALLIMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED NO VERBAL OR WRITTEN INFORMATION GIVEN BY SUPREME POWER USA LLC ITS AGENTS EMPLOYEES RETAIL DEALERS OR INDEPENDENT CONTRACTORS SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER SUPREME POWER USA LLC SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE How state law relates to this warranty Some states do not allow t
10. dset display shows KEYS LOCKED press and hold the button to unlock it before you make a call Only one handset or the base unit can be connected to the outside line at a time If another handset is already using the line you need to wait until it has finished its call Make sure the batteries are fitted in your handset lf the Battery Level symbol on the display shows low put your handset back on the cradle to charge Try a different position for the base unit somewhere higher if possible or further from other electrical equipment Try moving the handset closer to the base unit 14 The phone does not ring Check that the base unit s main power adapter is plugged in and power is switched on The base unit needs main power for normal operation of the phone not just for charging the batteries Make sure you are using the telephone line cable that was supplied with your package My call was cut off when went out of range Now I can t use my handset Move the handset closer to the base unit before you try again to make a call There is interference and noise on the line I hear beeps from my handset while I monacall The Caller Display feature isn t working Move the handset closer to the base unit or to a different position Try moving the base unit so that it s not near other electrical equipment such as a television or a
11. ed with this product lt is designed to be connected to acompatible modular jack that is also compliantSee installation instructions for details Notes e This equipment may not be used on coin service provided by the telephone company e Party lines are subject to state tariffs and therefore you may not be able to use your own telephone equipment if you are on a party line Check with your local telephone company e Notice must be given to the telephone company upon permanent disconnection of your telephone from your line e If yourhome has specially wired alarm equipment connected to the telephone line ensure the installation of this product does not disable your alarm equipment f you have questions about what will disable alarm equipment consult your telephone company or a qualified installer US Number is located on the cabinet bottom REN Number is located on the cabinet bottom 2 2 Rights of the Telephone Company Should your equipment cause trouble on your line which may harm the telephone network the telephone company shall where practicable notify you that temporary discontinuance of service may be required Where prior notice is not practicable and the circumstances warrant such action the telephone company may temporarily discontinue service immediately In case of such temporary discontinuance the telephone company must 1 promptly notify you of such temporary discontinuance 2 afford you the opportunity to correct t
12. following items in main menu Phonebook Set Date Time Personal Set and Advanced Set Personal setting 1 Make sure the phone is OFF not in TALK SPEAKER mode 2 Press the MENU OK button to go to main menu 3 Press the Navigation or button to select Personal Set 4 Press the MENU OK button to access the setting sub menu Handset tone From Personal Set sub menu 1 Press the Navigation or button to select Handset Tones 2 Press the MENU OK button to access handset tone setting you may program the following items Ring Volume Ring Melody and Key Beep Ring volume From Handset Tones setting sub menu 1 Press the Navigation or button to select Ring Volume 2 Press the MENU OK button to enter the menu 3 Press the Navigation or button to select the desired ringer volume level High Medium Low and Silence 4 Press the MENU OK button to save your selection You will hear a confirmation tone NOTE If you select Silence Ringer off icon shows on the display Ring melody You may choose from ten different melodies for aring tone From Handset Tones setting sub menu 1 Press the Navigation or button to select Ring Melody 2 Press the MENU OK button to enter the menu 3 Press the Navigation or button to select the desired melody ring tone 4 Press the MENU OK button to save your selection You will hear a confirmation tone Key Beep From Handset Tones setting sub
13. he battery fully You may need to replace the battery Check the connection between the base unit and the main power socket Itry to recharge the battery but still get a warning that they are low You need to replace the battery Dispose of used batteries safely never burn them or put them where they could get punctured Do not use non rechargeable battery in your handset they may explode causing damage If the fault persists Disconnect all other instruments connected to the same line and try to make a call Disconnect the base unit from the telephone line and plug a different phone into the master telephone socket Try making a call If this works the line is OK If the call does not work and you are using a two way socket adaptor remove it and plug a telephone directly into the socket If the call now works the adaptor may be faulty If you cannot make a call the fault may be on the exchange line Contact the service provider 16 Warranty Assistance Your sales receipt will be required to demonstrate proof of purchase in order to validate your warranty eligibility You may want to attach either the original or a photocopy of your sales receipt to this booklet for future reference If this product was received as a gift it is suggested you jot down the date of gift receipt as this information will be valuable should service be required during the warranty period If the equipment i
14. he exclusion nor limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you also may have other rights that vary from state to state If you purchased your product outside the USA or Canada This warranty does not apply Contact your dealer for warranty information Product Registration Please complete and mail the Product Registration Card packed with your product or visit www rca4phones com to register your new 19 product Product registration is not required for warranty coverage but does allow us to contact you should it be necessary Visit the RCA web site at www rca4phones com Please do not send any products to the Indianapolis address listed in this manual or on the carton This will only add delays in service for your product 2130 Printed in China 10 35
15. he situation and 3 inform you of your right to bring a complaint to the Commission pursuant to procedures set forth in Subpart E of Part 68 FCC Rules and Regulations The telephone company may make changes in its communications facilities equipment operations or procedures where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations If these changes are expected to affect the use or performance of your telephone equipment the telephone company must give you adequate notice in writing to allow you to maintain uninterrupted service Interference Information This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation Privacy of Communications ma
16. kel metal Hydride battery listed in the User s Guide e Keep batteries out of the reach of children e Remove batteries if storing over 30 days Troubleshooting You have followed all the steps listed in the user manual to install and set up your telephone Allconnectors are firmly inserted in their sockets Main power to the base unit is switched on at the socket The handset s batteries are correctly and securely installed and are not run down 13 Everyday use I cannot make or answer calls If the handset s display is blank it may have been switched off Press and hold the HANG UP key to switch it back on Check that the base unit s main power adapter is plugged in and power is switched on The base unit needs main power for normal operation of the phone not just for charging the batteries Make sure you are using the telephone line cable supplied with your phone Other telephone line cables might not work Move the handset closer to the base unit Check the battery level symbol on the display If it is low replace the handset on the base unit or charger pod to recharge the batteries Switch off power at the main socket wait for a short time and then switch back on This may solve the problem I cannot make a call When I press on the keys nothing happens When I key in a number it appears on the display but cannot make an outside call If the han
17. menu 1 Press the Navigation or button to select Key Beep 2 Press the MENU OK button to enter the menu 3 Press the Navigation or button to select On or Off 4 Press the MENU OK button to confirm You will hear a confirmation tone Handset Name From the Personal Set sub menu 1 Press the Navigation or button to scroll to the Handset Name sub menu 2 Press the MENU OK button to enter the menu 3 Use the touch tone pad to enter a name up to 10 characters More than one letter is stored in each of the number keys For example to enter Bill Smith press the 2 key twice for the letter B Press the 4 key 3 times for the letter I Press the 5 key 3 times for the letter L Press the 5 key 3 times for the second letter L and press the 1 key to insert a space between the first and last name Press the 7 key 4 times for the letter S press the 6 key once for the letter M press the 4 key 3 times for the letter press the 8 key for the letter T press the 4 key twice for the letter H NOTE 1 If you make a mistake use the BACK R C button to backspace and delete one character at a time 2 Use the Pause ringer button to toggle between upper case and lower case text entry 10 4 Press the MENU OK button to save your name You will hear a confirmation tone and the handset name shows in the display Auto answer From the Personal Set sub menu 1 2 3 4 Press the Navigation or button
18. onnerie IES sert indiquer le nombre maximal de terminaux qui peuvent tre raccord s une interface t l phonique La terminaison d une interface peut consister en une combinaison quelconque de dispositifs la seule condition que la somme d indices d quivalence de la sonnerie de tous les dispositifs n exc de pas 5 This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following Do not use this product near water for example near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool Avoid using a telephone other than a cordless type during an electrical storm There may be a remote risk of electric shock from lightning Do not use the telephone to report a gas leak in the vicinity of the leak Use only the power cord and batteries indicated in this manual Do not dispose of batteries in a fire They may explode Check with local codes for possible special disposal instructions SAVE THESE INSTRUCTIONS CAUTION A DO NOT OPEN THE Apeh CAUTION TO REDUCE THE THE EXCLAMATION WARNING TO RISK OF ELECTRIC SHOCK DO 0 OVE COVER 0 PREVENT FIRE OR S BARK NOUSER o v ELECTRICAL SHOCK SERVICEABLE
19. s causing harm to the telephone network the telephone company may require that you disconnect the equipment until the problem is resolved Purchase Date or Date Received as Gift Name of Store For instructions on how to obtain warranty service you may call Customer Care at 1 877 722 4908 or you may visit our website at www rca4phones com If you prefer you may write to us at Supreme Power USA LLC PO Box 501045 Indianapolis IN 46250 1045 Please do not send products to this address as it only adds delays in service and may result in lost or damaged product This PO BOX is for written communication only If the equipment is causing harm to the telephone network the telephone company may require that you disconnect the equipment until the problem is resolved Limited Warranty What your limited warranty covers e Defects in materials or workmanship For how long after your purchase e One year from date of purchase Please retain your sales receipt as that will act as your proof of purchase in order to validate warranty status What we will do e Provide you with a new or at our option a refurbished exchange unit of same or similar model The exchange model is under warranty for 17 the remainder of the original product s one year warranty or 90 days from the date the replacement product was shipped to you whichever is longer How to get service Call Customer Care at 1 877 722 4908 Please have your product
20. to scroll to the Auto Answer sub menu Press the MENU OK button to enter the menu Press the Navigation or button to select On or Off Press the MENU OK button to confirm You will hear a confirmation tone If you select ON during an external call you may lift the handset to answer a call immediately without pressing any buttons to end a call put the handset back on the cradle directly Auto hang up This function enables you to end a call automatically by simply placing the handset on the base station By default the Auto Hang up feature is off From the Personal Set sub menu 1 Press the Navigation or button to scroll to the Auto Hang up sub menu 2 Press the MENU OK button to enter the menu 3 Press the Navigation or button to select On or Off 4 Press the MENU OK button to confirm You will hear a confirmation tone Language From the Personal Set sub menu de 2 3 4 Press the Navigation or button to scroll to the Language sub menu Press the MENU OK button to enter language setting Press the Navigation or button to select the desired language Press the MENU OK button to confirm your selection You will hear a confirmation tone Using multi handset capabilities Note To use intercom feature you need to have at least 2 handsets link to this product This product is capable of linking up to 4 handsets 11 Making an intercom call 1 Make sure the phone is OFF
21. with FCC RF radiation exposure limits set forth for an uncontrolled environment this equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body This transmitter must not be co located or operated in conjunction with any other antenna or transmitter For body worn operation this phone has been tested and meets the FCC RF exposure guidelines when used with the belt clip supplied with this product Use of other accessories may not ensure compliance with FCC RF exposure guidelines Information for DECT Product This telephone is compliant with the DECT 6 0 standard which operates in the 1 92GHz to 1 93GHz frequency range Installation of this equipment is subject to notification and coordination with UTAM Any relocation of this equipment must be coordinated through and approved by UTAM UTAM may be contacted at 1 800 42 9 8826 Industry Canada I C Notice This product meets the applicable Industry Canada technical specifications Le pr sent materiel est conforme aux specifications techniques applicables d Industrie Canada The Ringer Equivalence Number is an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five L indice d quivalence dela s
22. y not be ensured when using this product If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna that is the antenna for radio or television that is receiving the interference 3 e Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna e Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is connected If these measures do not eliminate the interference please consult your dealer or an experienced radio television technician for additional suggestions Also the Federal Communications Commission has prepared a helpful booklet How To Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Please specify stock number 004 000 0034 5 4 when ordering copies Notice The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Hearing Aid Compatibility HAC This telephone system meets FCC standards for Hearing Aid Compatibility FCC RF Radiation Exposure Statement This equipment complies
Download Pdf Manuals
Related Search