Radio Shack PLVSHR77 User's Manual
Contents
1. area Remove the headrest and set it in an uncluttered work area Take the appropriate precautions to ensure that itis not damaged during the installation y Se Step 2 Make your measurements Push on the headliner with your fingers to make sure there are no obstructions that would hinder the installation Use the paper template to mark the area to be cut u d Step 3 Carefully cut the headrest S Using an adjustable depth blade start your cut 1 4 inch inside one corner and cut diagonally across stopping 1 4 inch in from the other corner Repeat the procedure for the other two corners Step 4 Remove form and obstructions from the opening Carefully peel back the material Set the adjustable blade to one inch depth and cut around the edges ofthe hole staying 1 4 inch inside the edge Pull up one corner of the foam and use the blade to cut underneath Remove small sections at a time using the pull up and cut method for uniform depth Use a Dremel or other appropriate tool to remove other obstructions Insert the monitor to measure the fit and make adjustments if necessary 5 Step 5 Route the wiring through the headrest Run the supplied cable through the opening and out the bottom of the headrest If possible conceal the wires using a shaft covering Connect the power ground and video leads to test the Monitor Step 6 Insert the headrest bezel Before connecting the monitor pul2. PLVSHR77 Table of Contents 1 Table of Contents l 2 Warning l 3 Installation 2 4 Features 3 4 1 Features 3 4 2 Remote Control Bar 3 4 3 Function keys at front panel 4 5 Installation for Monitor 5 6 Accessorles 7 7 Specifications 7 WARNING This unit is not intended for installation in the front Driver Passenger Compartment where t may be seen by the Driver Installation of this unit in any portion of the vehicle which could impair or distractthe Driver is improper and dangerous and PYLE view assumes No liability whatsoever for failure to follow the proper installation of this product To reduce the r sk of electric shock please do not expose this unit to rain moisture or open the unit Dangerous high voltages are present inside the unit Our warranty could be voided if you make changes or modifications not expressly approved by PYLE view 3 INSTALLATION l 2 3 4 GN Once you have confirmed the location of the Rotate the locking knob on the neck of the mounting stand clockwise Slide the engagement
3. able 10 Audio in Red RCA Jack 11 Video in Yellow RCA Jack 12 Power Wire Red 13 Grounding Wire Black 4 2 Remote Control Bar POWER MUTE FUNC UP MODE DOWN To adjustfunctions of Monitor use only 5keys Power Press the Power button for ON OFF Mute To shutdown Audio output Function Press the Function button to access On Screen Display Menu of CONTRAST BRIGHTNESS COLOR SHARPNESS SOURCEIN VOLUME MODE LEFT RIGHT RECALL EXIT UP To Adjust Volume Up DN To Adjust Volume Down MODE Selection button for AV1 AV2 4 3 FUNCTION KEYS AT FRONT PANEL 1 MENU FUNCTIONS CONTRAST Press A or Y to adjust Contrast BRIGHTNESS Press A or W to adjust Brightness COLOR Press A or Y to adjust Color SHARPNESS Press A or Y to adjust Sharpness SOURCE IN Selection button for AV1 AV2 VOLUME Press A or Y to adjust Volume MODE 16 9 4 3 LEFT RIGHT Left Right Revolving RECALL The Display will Return to The Original by Factory EXIT Exit Menu Mode 1 POWER Press the POWER button once it will be power ON Press it again The will be power OFF 2 UP DOWN Press UP or DN directly is to adjust volume Using MENU button together can adjust the other functions 5 Installation for Monitor Note It is recommended that the fitting is carried out ata specialist workshop Step 1 Set up your work
4. head on the mounting stand into the slide bracket slot on the rear of the monitor housing Rotate the locking knob counterclockwise until 1t is hand tight and the monitor is securely fastened to the neck of the mounting stand Locate a desirable spot in your vehicle for the y monitor Hold 1t place there with the mounting plate resting in approximately the right location Y and have a friend sit in the seat from which you Vy intend viewing of this monitor to take place to confirm the location of the monitor If necessary loosen the angle adjustment knob and rotate the monitor to a more ideal angle and retighten monitor remove the adhesive backing from the underside of the mounting plate and firmly press all the petals of the mounting plate Hs down to the car surface Temporarily remove the monitor by loosening the locking knob and use three screws in the locations indicated in the drawing below to further secure the monitor mounting plate If necessary drill pilot holes to 2s assist in inserting the screws E Reinstall the monitor onto the neck of the mounting stand and tighten the locking knob Adjust the monitor RS SA s A angle again as required being sure to tighten the angle T adjustment knob when you are done NUS Bee 4 Function 4 1 Features 1 Headphone Jack 2 Power 3 UP key 4 IR Sensor 5 Down key 6 Menu 7 AV IN Jack 8 Interface cable 9 System C
5. io input range Audio output power 12Vdc 10 1A 10 OC 60 C 25 C 70 C 7 16 9 TFT active matrix 1440 x 234 dots 190 W x 126 8 H x 36 D mm lt 450 208 NTSC PAL Dual System View Area L R 45 45 Top down 30 60 degrees 0 5 1 25Vp p 75 Ohms composite signal 0 1 5Vp p 620 Ohms 50Hz 20K Hz 0 5W Max The specifications are subject to change without prior notice
6. l the connecting cable assembly through the mounting base as shown in diagram 2 Place mounting base into the opening and secure 1t with correct fasteners A Step 7 Insert the monitor e Before connecting the monitor pull the gt gt connecting cable assembly through the mounting base as shown in diagram 2 e Place mounting base into the opening and Monitor secure 1t with correct fasteners Mounting base Step 8 Test and adjust the monitor then apply the Velcro Connect the monitor temporarily fit 1t into the opening and set the headrest in place Check the brightness headphone volume control ofthe monitor Apply the Velcro strips to the back ofthe monitor into place pressing from the edge not on the screen Removal Insert Y plate between monitor and mounting base to remove the monitor Release le Focus on the concave of monitor and mounting base to insert Y plate 6 ACCESSORIES 1 Monitor Stand x 1 2 System Cable x 1 3 Operation Manual x1 4 Release Key x1 5 Remote Controller x 1 6 Warranty Card x 1 7 Specifications 11 Supply voltage Power consumption Operating temperature l 2 3 4 Storage temperature 5 6 7 8 Monitor screen size Operating system Resolution Monitor overall dimension 9 10 Monitor weight System Viewing angle L R T D 12 13 14 Video input range Aud
Download Pdf Manuals
Related Search