Radio Shack 13.8VDC User's Manual
Contents
1. safety and operating instructions should be retained for future reference Heed Warnings Follow all warnings on the appliance and in the instructions Cleaning Unplug this appliance from the wall outlet before cleaning Use a damp cloth for cleaning Do not use liquid or aerosol cleaners Water and Moisture Do not use this appliance near water for example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool Mounting Accessories Do not place appliance on an unstable cart stand tripod bracket or table The appliance may fall causing injury to a child or adult and damage the appliance Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the appliance Follow the manufacturer s mounting instructions and use a recommended mounting accessory Ventilation Slots and openings in the cabinet provide ventilation ensure reliable operation and protect from overheating Do not block or cover these openings and do not place the appliance on a bed sofa rug or other similar surface Do not place the appliance in a built in installation such as a bookcase or rack unless it provides proper ventilation as specified by the manufacturer Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances that produce heat Power Sources Use this appliance with the powe2. RadioShack 22 508 13 8VDC 15A Power Supply Your RadioShack 13 8 VDC 15 Amp Regulated Power Supply is designed to power equipment that requires 12V DC automotive power The power supply converts standard 120V AC household power to 13 8V DC power and can supply up to 15 amps of continuous power Note Actual product may vary from the images shown in this document power supply user s guide WARNING To reduce the risk of fire or shock hazard do not expose this product to rain or moisture CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEAB LE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL The lightning sy mbol is intended to alert you to the presence of uninsulated dangerous voltage within this product s enclosure that might be of sufficient magnitude to constitute a risk of electric shock Do not open the product s case The exclam ation sym bolis intended to inform you thatimportant operating and maintenance instructions are included in the literature accompanying this product 2004 RadioShack Corporation All rights reserved RadioShack and 22 508 RadioShack com are trademarks 07A04 used by RadioShack Corporation Printed n China connections Make all other connections before you connect the power supply to standard AC power connect device with positive and negative wires 1 Turn off the devic
3. e requiring power 2 Turn off the power supply 3 Turn the red and black binding output posts counterclockwise to expose the wire holes RadioShack SWITCHING POWER SUPPLY black binding post red binding post 4 Insert the device s positive wire usually red into the red binding post s wire hole Tighten the binding post to secure the wire in place 5 Insert the device s negative wire usually black into the black binding post s wire hole Tighten the binding post to secure the wire in place 6 Connect the power supply s AC cord to a standard 120V AC outlet To avoid damage to the power supply and device e Make sure your connections match the correct polarity to to e Do not let the ends of the positive and negative wires touch each other e The binding posts wire holes can accommodate wire up to 18 gauge 90wer suppl Press POWER to turn on the power supply If POWER does not light e Check your connections and confirm the AC outlet has power If the outlet has power turn off the power supply and reduce the load use a device that requires 13 8V DC or less Press POWER Your power supply s overload protection circuit automatically shuts down the power supply when it becomes overloaded It resets when you turn off the power supply important safety instructions Read Instructions Safety and operating instructions should be read prior to use Retain Instructions The
4. hority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation limited 90 day warranty This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for ninety 90 days from the date of purchase from RadioShack company owned stores and authorized RadioShack franchisees and dealers For complete warranty details and exclusions check with your local RadioShack store RadioShack Customer Relations 200 Taylor Street 6th Floor Fort Worth TX 76102 04 04
5. mensions HWD Specifications are typical individual units might vary Specifications are subject to change and improvement without notice the FCC wants you to know This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Aules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult your local RadioShack store or an experienced radio TV technician for help If you cannot eliminate the interference the FCC requires that you stop using your power supply Changes or modifications not expressly approved by RadioShack may cause interference and void the user s aut
6. r source indicated on its marking label If you are not sure of your home s power type consult your appliance dealer or local power company Grounding or Polarization This appliance is equipped with a three wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug Power Cord Protection Route power supply cords so they are not likely to be walked on or pinched by items placed on or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the appliance Cleaning The appliance should be cleaned only as recommended by the manufacturer Clean by wiping with a cloth slightly dampened with water Avoid getting water inside the appliance Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching power lines or circuits as contact with them might be fatal Nonuse Periods The appliance s power cord should be unplugged from the outlet when it is to be left unused for a long pe
7. riod of time Overloading Do not overload wall outlets extension cords or integral convenience receptacles This can result in fire or electric shock Objects and Liquids Never spill liquids or push objects of any kind into this appliance through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Carts and Stands If the appliance is used with a cart or stand the cart or stand should be a type recommended by the manufacturer An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces cause the appliance and cart combination to overturn Damage Requiring Service Refer servicing to qualified service personnel under these conditions When the power supply cord or plug is damaged Liquid was spilled or objects fell in the appliance Ifthe appliance has been exposed to rain or water Ifthe appliance does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the appliance to normal operation If the appliance has been dropped or damaged When there a distinct change in performance Servicing Do not attempt to service this appliance yourself as opening or removing cover
8. s may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Replacement Parts When replacement parts are needed use only parts specified by the manufacturer or parts with the same characteristics as the original part Substitutions may result in fire or electric shock Safety Check Upon completion of service or repairs ask the service technician to perform safety checks to determine if the appliance is in operating condition Lightning For added protection during a lightning storm or when the appliance is unused for long periods of time unplug it from the wall outlet This prevents damage due to lightning and power surges Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer specifications Input Voltage Input Frequency 13 8VDC 0 7 Volts 15 Amps DC continuous max Less Than 1 Less Than 5 Output Voltage Output Current Line Regulation Load Regulation Overload Protection 6 3A 250V 200MVRMS Switching Type 32 to 104 F 0 to 40 C 4 to 140 F 20 to 60 C 18 AWG x 3C SVT 6 Feet Binding Post 10 Amp 125 Volts Illuminated 10A 250 VAC 65 6 x 61 x 2 inches 160 x 176 5 x 55 mm Storage Temperature Input Cable Output Terminal Power Switch Di
Download Pdf Manuals
Related Search