Quantum LTO-5 Quick Start Guide
Contents
1. Drive Interface and AC Power Connectors The installation of the tabletop LTO 5 tape drive differs depending on the drive type Half Height or Full Height Refer to the following sections for your drive type e Installing the Tabletop LTO 5 Half Height Tape Drive e Installing the Tabletop LTO 5 Full Height Tape Drive To install the tabletop LTO 5 Half Height Tape Drive complete the following procedures in the order presented 1 Connecting the Tabletop Drive Interface and AC Power Cables 2 Restarting the Tabletop Half Height Tape Drive System on page 12 3 Installing the LTO Driver Software on page 14 if required Connecting the Tabletop Drive Interface and AC Power Cables As shown in figure 8 the rear panel of the tabletop LTO 5 Half Height Tape Drive has connectors for e A 26 pin SFF 8088 mini SAS style interface cable e The AC power cable 26 pin SFF 8088 mini SAS connector D AC power connector Connect the interface and AC power cables to the tabletop drive as follows Installing the Tabletop LTO 5 Tape Drive 11 Installing the Tabletop LTO 5 Full Height Tape Drive Product Name Quick Start Guide 1 As required a Save and close your open files and terminate all running applications b Shut down the workstation or server system c Disconnect the system AC power cord from the facility AC power receptacle 2 Attach the external SAS interface cable to the 26 pin SFF 8088 mini SAS connector on the back2. of the drive 3 Verify that the tabletop LTO 5 Half Height Tape Drive AC power switch is set to the off position and connect the AC power cord to the power connector on the back of the drive 4 Connect the drive AC power cord to the facility AC power receptacle 5 Reconnect the workstation or server system AC power cord to the facility AC power receptacle After connecting the tabletop drive interface and AC power cables proceed to Restarting the Tabletop Half Height Tape Drive System in the following subsection Restarting the Tabletop Half Height Tape Drive System After connecting the tabletop drive interface and AC power cables 1 Set the tabletop drive AC power switch to the on position 2 Restart the workstation or server system 3 Verify that the tabletop LTO 5 Half Height Tape Drive comes on and completes the Power On Self Test POST functions As required proceed to Installing the LTO Driver Software To install the tabletop LTO 5 Full Height Tape Drive complete the following procedures in the order presented 1 Connecting the Full Height Tabletop Drive Interface and AC Power Cables 2 Restarting the Tabletop Full Height Tape Drive System on page 14 3 Installing the LTO Driver Software on page 14 if required Connecting the Full Height Tabletop Drive Interface and AC Power Cables As shown in figure 9 the rear panel of the tabletop LTO 5 Full Height Tape Drive has connectors for e A 26 pin SFF
3. 1 Restarting the Tabletop Half Height Tape Drive System usss 12 Installing the LTO Driver Software 14 Safety Compliances ceeeeeeee 14 Electromagnetic Compatibility EMC Gomplianees 3 sc isis eeceseves senesnes 15 www quantum com Product Name Quick Start Guide Figure 1 Internal Drive Half W _ we ew we eo Height Encryption Clean Tope Drive Roody Figure 2 Internal Drive Full z Height Before Installing the LTO 5 Tape Drive Handling Precautions Always observe the following precautions and guidelines when handling and installing and Installation LTO 5 Tape Drives Guidelines e Internal at all times e Tabletop when removed from its free standing enclosure 2 Before Installing the LTO 5 Tape Drive Handling Precautions e Internal drives have exposed components that are sensitive to static electricity To reduce the possibility of damage from static discharge the drives are packaged in a protective antistatic bag Do not remove the drive from the antistatic bag until you are ready to install it Wear an ESD preventive grounding wrist strap or observe similar ESD precautions when working with the drive Be sure the wrist strap makes good skin contact Do not remove the wrist strap until you finish working with the drive Also avoid contact between the drive other equipment and clothing The wrist strap only protects the equipment from ESD voltages on the body ESD v
4. 8088 mini SAS style interface cable e The AC power cable Installing the Tabletop LTO 5 Tape Drive Figure 9 Tabletop Full Height Drive Interface and AC Power Connectors 26 pin SFF 8088 mini SAS AC power switch connector LMM yes AC power connector Connect the interface and AC power cables to the tabletop drive as follows 1 As required a Save and close your open files and terminate all running applications b Shut down the workstation or server system c Disconnect the system AC power cord from the facility AC power receptacle 2 Attach the external SAS interface cable to the 26 pin SFF 8088 mini SAS connector on the back of the drive 3 Verify that the tabletop LTO 5 Full Height Tape Drive AC power switch is set to the off position and connect the AC power cord to the power connector on the back of the drive 4 Connect the drive AC power cord to the facility AC power receptacle 5 Reconnect the workstation or server system AC power cord to the facility AC power receptacle After connecting the tabletop drive interface and AC power cables proceed to Restarting the Tabletop Full Height Tape Drive System in the following subsection Installing the Tabletop LTO 5 Tape Drive 13 Product Name Quick Start Guide Restarting the Tabletop Full Height Tape Drive System After connecting the tabletop drive interface and AC power cables 1 Set the tabletop drive AC power switch to the on positi
5. Height Tape Drive has connectors for e 29 pin SFF 8482 SAS cable Installing the Internal LTO 5 Tape Drive 9 Figure 7 Internal Full Height Drive Interfaces 4 pin Molex power connector Product Name Quick Start Guide Connect the interface cables to the internal drive as follows 1 4 5 Verify that the system is shut down and the AC power cord is disconnected from the facility AC power receptacle Connect the SAS connector on the back of the tape drive to a serial SCSI host bus adapter HBA installed in the server Ensure that a 4 pin Molex power connector is plugged into the power inputs of the SAS cable as shown in figure 7 Reinstall the system cover Reconnect the system AC power cord to the facility AC power receptacle After connecting the internal drive interfaces proceed to Restarting the Internal Full Height Tape Drive System in the following subsection Restarting the Internal Full Height Tape Drive System After connecting the internal drive interfaces 1 Restart the workstation or server system 2 Verify that the internal LTO 5 Full Height Tape Drive comes on and completes the Power On Self Test POST functions As required proceed to Installing the LTO Driver Software on page 14 10 Installing the Internal LTO 5 Tape Drive Installing the Tabletop LTO 5 Tape Drive Installing the Tabletop LTO 5 Half Height Tape Drive Figure 8 Tabletop Half Height
6. LTO 5 Tape Drive Quick Start Guide LTO Ultrium tape drives leverage LTO technology and exclusive features to provide the most reliable and affordable tape data protection to medium and large businesses The LTO 5 tape drive is available in the following models LTO 5 Half Height Internal tape drive TC L52AN BR and EY LTO 5 Half Height external tape drive TC L52BN AR 1U Rackmount TC L53CN AR LTO 5 Full Height Internal tape drive TC L51AN BR LTO 5 Full Height external tape drive TC L51BN AR 3U Rackmount TC L51FN AR These drives are the most reliable Ultrium drives on the market delivering reliability features to extend media life and Variable speed Transfer to automatically match the host s data transfer rate Combined with SmartVerify to concurrently verify all data written to the tape these features make LTO drives a sound investment and a complete data protection solution Before Installing the LTO 5 Tape Drive 2 Handling Precautions and Installation Guidelines meee 2 Preinstallation Requirements 3 Unpacking and Inspecting the Drive 4 Installing the Internal LTO 5 Tape Drive 4 Mounting the Internal Half Height Tape a E tertece evs caves cosines 5 Connecting the Internal Half Height Drive Interfaces ee eee 7 Restarting the Internal Half Height Tape Drive System nsss 7 Installing the Tabletop LTO 5 Tape Drive11 Connecting the Tabletop Drive Interface and AC Power Cables 1
7. ates Federal Communications Commission FCC Title 47 Code of Federal Regulations Part 15 Subpart B 47CFR15B Electromagnetic Compatibility EMC Compliances Product Name Quick Start Guide Note Use these drives only in equipment where the combination has been determined to be suitable by an appropriate certification organization for example Underwriters Laboratories Inc or the Canadian Standards Association in North America You should also consider the following safety points e Install the drive in an enclosure that limits the user s access to live parts gives adequate system stability and provides the necessary grounding for the drive e Provide the correct voltages 5 VDC and 12 VDC based on the regulation applied Extra Low Voltage SEC for UL and CSA and Safety Extra Low Voltage for BSI and VDE if applicable ANETTA AA N 16 6 66788 01 Rev A March 2010 For assistance contact the Quantum Customer Support Center About Quantum USA EMEA Quantum Corp NYSE QTM is the leading global storage company APAC specializing in backup recovery and archive Combining focused Worldwide expertise customer driven innovation and platform independence Quantum provides a comprehensive range of disk tape media and software solutions supported by a world class sales and service Qu a nt U mM organization This includes the DXi Series the first disk backup solutions to extend th
8. e Internal Full Height Tape Drive on page 8 2 Connecting the Internal Full Height Drive Interfaces on page 9 3 Restarting the Internal Full Height Tape Drive System on page 10 4 Installing the LTO Driver Software on page 14 if required Mounting the Internal Full Height Tape Drive Mount the internal drive in a 5 25 inch full height drive bay as follows 1 As required a Save and close your open files and terminate all running applications b Shut down the workstation or server system c Disconnect the system AC power cord from the facility AC power receptacle 2 Remove the cover from the workstation or server system Note See your computer manufacturer s instructions for the proper procedures to remove the cover 3 Select an available 5 25 inch full height bay and if required remove the bay cover 4 Position the drive in the bay and align mounting holes with the holes in the chassis see figure 6 5 Secure the drive using two screws on each side of the tape drive After mounting the internal LTO 5 Full Height Tape Drive proceed to Connecting the Internal Full Height Drive Interfaces in the following subsection Installing the Internal LTO 5 Tape Drive Figure 6 Internal Full Height Tape Drive Mounting Hole Locations rA A TY Mounting holes Connecting the Internal Full Height Drive Interfaces As shown in figure 7 the rear panel of the internal LTO 5 Full
9. e power of data deduplication and replication Backup Recovery Archive It s What We Do across the distributed enterprise As a long standing and trusted partner the company works closely with a broad network of resellers OEMs and other suppliers to meet customers evolving Protected by Pending and Issued U S and Foreign Patents including U S Patent No 5 990 810 data protection needs 2010 Quantum Corporation All rights reserved Quantum the Quantum logo and all other logos are registered trademarks of Quantum Corporation or of their respective owners
10. lling the Internal LTO 5 Tape Drive The installation of the internal LTO 5 tape drive differs depending on the drive type Half Height or Full Height Refer to the following sections for your drive type e Installing the Internal LTO 5 Half Height Tape Drive e Installing the Internal LTO 5 Full Height Tape Drive 4 Installing the Internal LTO 5 Tape Drive Installing the Internal LTO 5 Half Height Tape Drive Figure 3 Acceptable Mounting Orientations To install the internal LTO 5 Half Height Tape Drive complete the following procedures in the order presented 1 Mounting the Internal Half Height Tape Drive on page 5 2 Connecting the Internal Half Height Drive Interfaces on page 7 3 Restarting the Internal Half Height Tape Drive System on page 7 4 Installing the LTO Driver Software on page 14 if required Mounting the Internal Half Height Tape Drive You can mount the internal LTO 5 Half Height Tape Drive either horizontally or vertically but not upside down see figure 3 IF you mount the drive THEN the horizontally base of the drive must be within 15 degrees of horizontal vertically side of the drive must be within 5 degrees of horizontal r YES YES YES NO Mount the internal drive in a 5 25 inch half height drive bay as follows 1 As required a Save and close your open files and terminate all running applications b Shut down the workstation or server sys
11. ner and notify your carrier immediately of any damage 2 Place the shipping container on a flat clean stable surface and carefully remove the contents 3 Visually inspect the LTO 5 Tape Drive and notify your sales representative immediately of any damage 4 Always save the shipping container and packing materials for any future reshipment ESD Precautions Your internal tape drive has very sensitive components that are prone to damage from electrostatic discharge ESD Use extreme care when handling the drive as it can be damaged by ESD Before handling the drive read the following instructions e Wear an ESD preventive grounding wrist strap or observe similar ESD precautions when working with the drive Be sure the wrist strap makes good skin contact Do not remove the wrist strap until you finish working with the drive e Avoid contact between the drive other equipment and clothing The wrist strap only protects the equipment from ESD voltages on the body ESD voltages on clothing can still cause damage e When the drive is not being used keep it in its antistatic bag e Before you remove the drive from the antistatic bag touch a metal or grounded surface to discharge any static electricity buildup from your body e Hold the drive by its edges only Avoid touching any exposed parts on the printed circuit board e Always place the drive on top of or inside the antistatic bag to reduce the chance of ESD damage Insta
12. oltages on clothing can still cause damage Before removing the drive from the antistatic bag touch a grounded metal surface to discharge any static electricity buildup from your body Handle the drive by its sides rather than by the top cover to reduce the risk of dropping the drive or damaging it during installation Either lay the drive on a nonconductive surface or put it back inside the protective antistatic bag to reduce the chance of damage from static discharge Installation Guidelines For optimum performance do not connect more than two LTO 5 drives to the same host bus adapter HBA Preinstallation Before installing the LTO 5 Tape Drive make sure you have Requirements e A serial SCSI host bus adapter HBA installed and properly configured in the host computer e Interface components either e 29 pin SFF 8482 SAS cable e 26 pin SFF 8088 mini SAS style interface cable for a tabletop drive e Backup application software that supports the tape drive Before Installing the LTO 5 Tape Drive 3 Product Name Quick Start Guide Unpacking and Although each LTO 5 Tape Drive is inspected and carefully packaged at the factory Inspecting the Drive damage can occur in shipment or when the drive is being unpacked Observe the handling precautions in Handling Precautions and Installation Guidelines and carefully unpack and inspect the LTO 5 Tape Drive as follows 1 Visually inspect the shipping contai
13. on 2 Restart the workstation or server system 3 Verify that the tabletop LTO 5 Half Height Tape Drive comes on and completes the Power On Self Test POST functions As required proceed to Installing the LTO Driver Software Installing the LTO Driver Software If you intend to use the LTO 5 Tape Drive with the Microsoft native backup applet on a Windows 2000 Windows Server 2003 Windows 2008 Server Windows XP or Windows Vista operating system install the appropriate version of the LTO driver software available at www guantum com Note The LTO driver software is not necessary with commercial backup application software Safety Compliances The LTO 5 Half Height Tape Drives are safety compliant with the following regulatory organizations and codes in the countries indicated Country Regulatory Organization Compliant to Canada Canadian Standards Association UL CSA 60950 1 CSA EU member nations Comit Europ en de Normalisation EN 60950 1 1st Electrotechnique the European edition Committee for Electrotechnical Standardization CENELEC IECEE member IECEE International Electrotechnical CB Scheme per IEC nations Commission on Electrical 60950 1 with details Equipment IECEE for Mutual and exceptions for Recognition of Test Certificates for each member country Electrical Equipment CB Scheme Taiwan BSMI BSMI certification CNS 14336 14 Installing the LTO Dri
14. pe Drive has connectors for e 29 pin SFF 8482 SAS cable Figure 5 Internal Drive Interfaces 29 pin SFF 8482 SAS cable connector 4 pin Molex power connector Connect the interface cables to the internal drive as follows 1 Verify that the system is shut down and the AC power cord is disconnected from the facility AC power receptacle 2 Connect the SAS connector on the back of the tape drive to a serial SCSI host bus adapter HBA installed in the server 3 Ensure that a 4 pin Molex power connector is plugged into the power inputs of the SAS cable as shown in figure 5 4 Reinstall the system cover 5 Reconnect the system AC power cord to the facility AC power receptacle After connecting the internal drive interfaces proceed to Restarting the Internal Half Height Tape Drive System in the following subsection Restarting the Internal Half Height Tape Drive System After connecting the internal drive interface cables 1 Restart the workstation or server system 2 Verify that the internal LTO 5 Half Height Tape Drive comes on and completes the Power On Self Test POST functions As required proceed to Installing the LTO Driver Software on page 14 Installing the Internal LTO 5 Tape Drive 7 Installing the Internal LTO 5 Full Height Tape Drive Product Name Quick Start Guide To install the internal LTO 5 Full Height Tape Drive complete the following procedures in the order presented 1 Mounting th
15. tem c Disconnect the system AC power cord from the facility AC power receptacle 2 Remove the cover from the workstation or server system Note See your computer manufacturer s instructions for the proper procedures to remove the cover 3 Select an available 5 25 inch half height bay and if required remove the bay cover 4 Position the drive in the bay and align either the upper or lower mounting holes whichever is appropriate with the holes in the chassis see figure 4 Installing the Internal LTO 5 Tape Drive 5 Product Name Quick Start Guide 5 Secure the drive using two Phillips screws labeled General Mounting Screws on each side of the tape drive If you cannot tighten the Phillips screws use the washers provided with the General Mounting Screws Caution Using screws other than the Phillips screws labeled as General Mounting Screws can damage the tape drive Do not use screws other than the General Mounting Screws to secure the internal LTO 5 Half Height Tape Drive After mounting the internal LTO 5 Half Height Tape Drive proceed to Connecting the Internal Half Height Drive Interfaces in the following subsection Figure 4 Internal Tape Drive Mounting Hole Locations Upper mottnting holes 6 Installing the Internal LTO 5 Tape Drive Connecting the Internal Half Height Drive Interfaces As shown in figure 5 the rear panel of the internal LTO 5 Half Height Ta
16. ver Software Country Regulatory Organization Compliant to United States Underwriters Laboratories UL UL CSA 60950 1 IECEE member nations include Argentina Austria Australia Belgium Brazil Canada China PR Czech Republic Denmark Finland France Germany Hungary India Ireland Israel Italy Japan South Korea Montenegro Netherlands Norway Poland Russian Federation Serbia Singapore Slovakia Slovenia South Africa Spain Switzerland Turkey United Kingdom and USA Electromagnetic Compatibility EMC Compliances The LTO 5 Half Height Tape Drives are EMC compliant with the following regulatory organizations and codes in the countries indicated Country Regulatory Organization Compliant to Australia Australian Communications and Media Authority ACMA AS NZS 3548 same as CISPR 22 Canada Industry Canada Digital Apparatus Interference Causing Equipment Standard ICES 003 ICES 003 Digital Apparatus EU member nations CE Emissions per CISPR 22 EN55022 and Immunity per CISPR 24 EN55024 Japan Voluntary Control Council for Interface VCCI VCCI New Zealand Australian Communications and Media Authority ACMA AS NZS 3548 same as CISPR 22 South Korea MIC CISPR 22 and CISPR 24 Taiwan Bureau of Commodity Inspection and Quarantine BSMI BSMI EMC certification CNS 14338 United St
Download Pdf Manuals
Related Search