Python 951 User's Manual
Contents
1. Feature Opt 1 Opt 2 Opt 3 Opt 4 Opt 5 Auto keypad On Off Back lock Page On Off Power save Back Page alert Vibe Tone Both Screen only Back Remote start Clock Temp Runtime Back display low runtime On Off Back alert Car 2 On Off Home Back Back light color Off 17 Back Temp units F C Back Button press On Off back beep System type Remote start Remote start Back amp Security Clock set Clock time Back 2008 Directed Electronics All rights reserved 31 gt Menu option descriptions 32 Auto keypad lock Automatically locks the remote buttons when the buttons are not used for 60 seconds Prevents accidental presses of the remote Press f then BY to unlock the keypad Note If the auto keypad lock feature is programmed On the remote un locks when the vehicle ignition is turned Off The remote stays unlocked to allow time to exit and unload the vehicle and then lock the doors with the remote When the button is pressed the keypad auto lock feature resumes normally Page On or Off and Power save When paging is On the remote checks the status of the system every four seconds and reports any factory alarm triggers if the system is within the operating range and the factory alarm option is installed In the paging Off setting the remote does not check the status of the system In the paging Off mode the remote beeps when a button on the2. Label Back of remote has label to identify the remote as 2 way or way 9 Battery Door I way For accessing batteries when necessary 10 Transmit LED 1 way Active when communicating Note If Keypad Lock is On press f and then press S to exit 2008 Directed Electronics All rights reserved gt LC 1 way companion E x ACCEL OOOO SS See call out table for 2 way gt Transmitter configuration Level Direct Access Button Q ock Unlock A Remote Start Trunk Release f Function Shift fx x2 Fx 3 x4 Silent Lock Silent Unlock Valet Mode Car Finder Reset Timer Mode Smart Start Rear Runtime Defogger AUX 1 AUX 2 AUX 3 Cabin Runtime Temperature Check request 2 way only 2 way only 2008 Directed Electronics All rights reserved Using the system Please note the screen shot to the right of a feature indicates what the display looks like when this feature is activated Lock Command Press one time to Lock Feedback lock Icon appears and parking lights flash once Notes Press hold for 1 5 seconds to Lock the system and activate the panic feature Details The horn in the vehicle honks once if the op tion is installed and the parking lights flash one time If the power door locks have been connected the doors lock When panic is
3. remote Silent Lock Command Press f one time and then press A Feedback Screen changes to the lock icon Notes Locks the system without honks The system locks without the confirmation honk The parking lights flash once The 2 way remote blinks the LOCK icon to confirm locking If no lock confirma tion is received the 2 way remote gives the Out Of Range signal e FailSafe Starter Kill The starter is disabled by the system s Fail Safe starter kill Silent unlock 20 2008 Directed Electronics All rights reserved Command Press f one time and then press gt Feedback Screen changes to unlock icon Notes Unlocks the system without chirps gt Overriding the optional starter kill To bypass the optional starter kill without a remote control Use your override switch located on the control center see diagram below to bypass the system This switch bypasses the system only if you have the vehicle key To check proper operation 1 While the vehicle is locked open the door Immediately insert the key into the ignition and turn it to the run or on position all the indicators in the dash turn on 2 Press and release the Override Switch one time The optional starter kill is bypassed You can now start the vehicle with the key Note The Override Switch feature allows you to select a specific number of presses needed to unlock the system If the Override Switch has been pro grammed to a n
4. Directed is ISO 9001 registered Quality Directed Electronics products are sold and serviced throughout North America and around the world Call 800 274 0200 for more information about our products and services Designed and Engineered in the USA Lixected ELECTRONICS G4702P 2008 08 Vista CA 92081 www directed com 2008 Directed Electronics Alll rights reserved
5. E CO AS DEALE R LIMI WIT PURC ON LIAB NOT CO EU SA MAXIMUM RE TED RECT G 1 D E UNIT EGLI OT Al G OUT OF Some states do not allow sion or limi egal rights and you may This warranty is only va Product s sold outside of Make sure you have al dealer ation of incide WARRANTY express or impli Plan GPP See your authorized Di Customer Service at 1 800 876 0800 the fol G EF D imi nta a lid the DAMAG COMME STAI LITY D AP TO ED BUT R D BE EE OD FOR VER LAI T OR ANY CO A CLAIM OR A L BE SA D DIEGO PL COV TH SHALL OT Om NG TI TO REPLACE Ol ESCR ASED F HAS B TS OF D HERE ROM D ECT 0 ations on how or consequential damages so have other rights that vary or sale of product s within United S ed This THEF R COSTS FOR MAINT SEQU BO SPUTE COUNTY BLE FEDERAL LAVVS SH ERY UNDER A E AUTHORIZED OT BE RESPONS MITED TO ANY CO VEHICLE DAMAGES LOSS LOSS HE ABOVE TI R REPAIR bol REC CAI BI TO AL n Bi E MAI U HIS VVARRAI TED OR AN DAMAGED BY ACCIDE EGLECT IMPROPER SERV MATERIALS OR CONSTI RU rom S the U lates of America are I DAMAGE AND OR VA ENTIAL DAMAGES VOLVING DIRECTED OR THE STA ALL Y CLAIM DIRECT
6. gt Locking If the system is locked at the same time that the door is active you will hear one horn honk to indicate locking and a second horn honk to indicate Bypass Notification For example if your vehicle has an interior light exit delay and you lock the system before the interior light turns Off you may hear a second Bypass Noti fication honk Note Bypass Notification does not occur when the system is in Silent Mode or if the notification honks have been programmed Off by the installer gt Unlocking Extra honks when unlocking the system is a notification that the batteries in the remote are low and need to be replaced Important The optional horn honk feature must be installed 36 2008 Directed Electronics All rights reserved gt Remote start This system can provide you with information to indicate what the problem is when using the remote start When the remote start is activated and fails to engage count the parking light flashes to determine the problem The parking lights will flash between 5 8 times to indicate what caused the no start situa tion 5 flashes brake wire is active 6 flashes hood pin is active 7 flashes manual transmission mode is enabled and not initialized 8 flashes neutral safety wire has no ground or the remote start defeat toggle switch is off Keep a record of the number of flashes to assist your installer when taking the vehicle in for service 2008
7. Large Siren Feature only available on full security and remote start systems Does not apply to 4702 model Feature not available 43 Quick reference guide K 44 gt Locking To lock press the button The remote beeps onetime and the LCD displays locked gt Unlocking To unlock press the bution The remote beeps twotimes and the LCD displays unlock Cut along the dotted line and fold to keep in purse or wallet for a quick and easy reference gt Bypassing the optional starter kill without a remote Turn on the ignition Press and release the Valet button within 15 seconds The vehicle should now start If it does not you may have waited too long or pressed the button incorrect number of times i d Number of Valet button presses for disabling gt Silent Lock Press f onetime and then press a The lock icon turns on and the LCD displays silent lock gt Silent Unlock Press f onetime and then press The unlock icon tums on and the LCD displays silent unlock gt Remote Start Press The remote will play the remote start tones and the LCD text will display remote start on when activating When deactivating the remote start the remote will play the remote start Off tones and the LCD text will display remote start Off x 2008 Directed Electronics All rights reserved gt Rear Defogger x Press f fourtimes and then press 2
8. temperatures outside this range may cause 13 F Charging the battery at severe damage to the battery or reduce bat tery life expectancy gt Low battery indicator When the batteries are low on the 2 way remote it will emit two groups of beeps the battery icon flashes and ow battery is indicated on the screen The remote then emits an additional honk if this option is installed when unlocking to let you know its time to change the battery When the battery is low on the l way remote the remote responds he same way audibly Note The optional horn honks must be installed for the remote to emit additional honks during unlocking Ask your au gt Battery Replacement horized dealer if you have any questions Slide the door up to expose the battery beneath the holder Remove the expired battery Place the new battery into the remote control When power is returned the remote control is ready for use 2008 Directed Electronics All rights reserved 11 gt Multi car control capability You can use the Responder LC 2 way remote control system for two cars with full command capability for both vehicles To change the car to be operated 1 Press hold the F button for 3 seconds or until the remote beeps The car 1 or X 2 icon flashes The LC text area displays the current vehicle selected 2 Change Car While in car selection mode press and release the f button to scroll between
9. vated the remote plays the demo mode continuously The continuous loop demo mode is exited when the charger is disconnected 34 2008 Directed Electronics All rights reserved Safety features This system has several important safety features to ensure proper operation of the motor and prevent accidental damage to the engine or its components gt Optional starter anti grind circuitry Whenever the vehicle is remote started advanced anti grind circuitry prevents the starter from engaging even if the key is turned to the start position This pre vents damage to the starter motor if the key is turned to the start position during remote start operation Note Anti grind circuitry only works when the remote start system is operating the motor and the optional Failsafe Starter Kill relay is installed gt Disabling the remote start system This feature allows the remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally This feature is useful when the vehicle is being serviced or stored in an enclosed area To disable the remote start move the shutdown toggle switch to the Off position Check with your installer for the location of the shutdown switch Location of Shutdown Switch 2008 Directed Electronics All rights reserved 35 Diagnostics The microprocessor at the heart of the system is constantly monitoring the switch es that are connected to the main unit
10. 5 seconds Text reads runtime and displays time left This feature is only available on the 2way remote Command While the remote start is running press f onetime and then Feedback Remote start ON tones Notes Re starts the remote start runtime counter if remote start is ac tive Note If remote start is not active the 2 WAY remote will respond with error fone Rear defogger Command Press four times and then a Only after remote start is on Feedback Defogger icon appears on remote and text reads Defrost On Notes While the remote start is running the defroster will manually be turned on for one remote start cycle When the remote start shuts down the defroster will work normally The defroster turns on when the temperature inside the vehicle is 55 degrees or below when this feature is wired and enabled 26 2008 Directed Electronics All rights reserved Smart start Command Press ihreetimes and then press Feedback The parking lights flash 5 times fast and Smart Start On dis m plays in the text area Notes Enables or disables the SmartStart feature The smart start fea ure of this system will allow you to have the remote start ac ivate when the vehicle reaches a certain temperature hot or cold or a certain voltage The factory setting for temperature high is 100 F the setting for low is O F The voltage setting is or 10 5V These settings can be adjusted or turned off by your instal
11. If the factory release is not poweractivated Directed s 522T trunk release solenoid can often be added Power Window Control Automatic power window control is provided with the 529T and 530T systems These can operate power windows and can roll them up automatically when the system is Locked roll them down or both up and down 40 2008 Directed Electronics All rights reserved Glossary of terms 2 Way Remote A hand held remote control which operates the various func tions of your system and receives feedback and pages from the system Control Center The control center contains the system s radio frequency antenna the valet and override switch and the Status LED For maximum remote control range the Control Center is usually located at the top of the windshield cen tered near the rearview mirror Control Module The brain of your system Usually hidden underneath the dash area of the vehicle It houses the microprocessor which monitors your vehicle and controls all of the system s functions Failsafe Starter Kill if equipped An automatic switch controlled by the system which prevents the vehicle s starter from cranking whenever the system is locked The vehicle is never prevented from cranking when the system is unlocked in Valet Mode or should the starter kill switch fail Your system is ready for this feature however installation of this feature may require additional labor Input Any physical conn
12. car 5 and fan The car icon flashes to indicate the car that can be operated 3 Select the car number you want to operate and then press any command button to operate the system The selected car remains selected until the setting is changed One way remote 1 Press and hold the F button until the amber light blinks once or twice indicating the current vehicle one blink car 1 two blinks car 2 2 To scroll from one to the other press the F button again When using the remote to control the system the amber light will flash in a sequence of 1 or 2 flashes indicating the current vehicle mode 12 2008 Directed Electronics All rights reserved Responder LC 2 way T kA 1 800 274 0200 RPN 7752P IC 1513A 7752 FCC ID EZSDEI7752 Co Q9000 Feature Description LCD 2 way Activity icon display Lock button Press for one second to arm Press for one second to disarm 2 3 Unlock button 4 Auxiliary button Press and hold for 1 5 second to activate optional trunk release 5 Remote start button Press for one second to activate remote start 6 Function button Allows access to programming and modi fies operation of the other buttons 7 Charge Port 2 way Plug in the battery charger to this port
13. hour period while the system is in Valet Mode the status LED will shut Off If the system remains in Valet Mode the LED will come back on the next time the ignition is turned on and then back Off 38 2008 Directed Electronics All rights reserved gt 2 way remote Your Responder LC 2way remote control has a feature called remote power save mode When programmed On under remote options the remote conserves power by disabling the paging function if unused for more than 72 hours Pressing any button on the remote restores the paging function The default setting is On See Remote control programming section of this guide or ask your dealer for details on how to program Your system has many custom programmable options Some may require instal lation labor Ask your authorized dealer for details The following is a list of the programmable options with the factory settings in Bold e Active locking remote only passive locking will lock the doors 30 sec onds after the ignition is turned Off and the last door has been closed or Auto Re lock automatically locks 60 seconds after unlocking if no door is opened e Locking Unlocking with horn honks On or Off e Ignition controlled door lock feature On or Off When this feature is pro grammed on the doors will lock three seconds after the ignition is turned on and unlock when the ignition is turned Off If your installer is programming the system ignition lock an
14. remote is pressed n the battery saver mode the remote goes into sleep mode if no buttons are pushed for 72 hours The timer resets each time a button is pressed Page Alert Vibe Beep Tone Both or Screen only Receive command confirmations on the remote with vibrations beeps or both or with display only Remote start display Clock temperature and runtime Allows you to choose what is displayed in the text during the remote start sequence Clock displays the current time during remote start Temperature displays the current cabin temperature during the remote start Runtime displays the runtime remaining during the remote start 2008 Directed Electronics All rights reserved e Low Runtime Alert The remote reports with one short beep followed by 1 short error tone repeated twice and the text area displays run time when the remote start runtime is at the 3 minutes remaining The remote beeps one more time when minute is remaining You have the option to let the remote start time out or use the runtime reset feature When programmed Off you will not receive a low runtime alert on the remote e Car 2 On or Off Home Turns Off or On the 2 car operation from the remote The Home option is not available e Backlight Color Off 1 8 Turn Off the LCD backlighting or change the color of the backlighting Color options include Blue green red aqua purple lime clear e Temperature Units F and C Disp
15. 2008 Directed Electronics All rights reserved 23 Timer Mode is exited automatically after the sixth run cycle The parking lights slowly flash 4 times when exiting timer mode Note The Bitwriter can change the amount of times the remote start activates and it can change the intervals between activations in timer mode Turbo Timer mode Turbo timer mode keeps the engine running after arriving at your destination for a programmable period of 1 3 5 or 10 minutes This allows the system s timer to conveniently cool down the turbo after you have left the vehicle The system monitors the engine speed and will automatically shut the engine off if the RPMs rise above or fall below the programmed levels This feature prevents damage to the motor due to fuel delivery system failures or other problems that may cause the engine to race To activate Turbo Timer Mode with an automatic transmission 1 Make sure the Turbo timer feature is turned on in the features grid 2 Open the vehicle door 3 While the vehicle is running press the f button twice followed by the 7 button 4 The parking lights flash once and the remote plays the remote start activa tion tone confirming that the remote start is activated the one way remote only flashes the parking lights 5 Turn off the ignition car stays running 6 Exit the vehicle and lock the system At this point the vehicle stays running for the programmed runtime 24 2008 Directe
16. Directed Electronics All rights reserved 37 Owner recognition Owner recognition lets up to four users of the system have unique settings that meet their specific needs It is almost like having four separate systems in your vehicle one for each user This feature is only available to authorized dealers using the Bitwriter or Bitwriter 2 program tool Rapid resume logic This Directed system will store its current state to non volatile memory If power is lost and then reconnected the system will recall the stored state from memory For example if the unit is in Valet Mode and the battery is disconnected for any reason such as servicing the car when the battery is reconnected the unit will still be in Valet Mode This applies to all states of the system including lock or unlock Power saver mode gt System Your system automatically enters Power Saver Mode while locked or in Valet Mode after a period of time in which no operation has been performed This lowers the current draw on the vehicle s battery Power Saver Mode takes over under the following conditions Power Saver when the system is locked After the system has been Locked for 24 hours the LED will flash at half its normal rate decreasing the system s cur rent draw Power Saver in Valet Mode When the system enters Valet Mode the Status LED on the Responder LC control center illuminates steadily If the vehicle is not used ignition is not turned on for a one
17. ED LE FOR Al SEQUENT FOR THE OF ECONOMIC UFACTURER DOES Ol THE CONTROL MODU TY IS VO AUTHORIZED DIREC T UNREASONABLE CE OR OTHER CAUSES ong an implied warranty will last or the exc This warranty gives you speci DALISM THIS ANCE REMOVAL OR OF ANY K TS SUBSID TE OF CALIFOR APPLY AND GOVI AGAINST DIREC DEALER S PURCH Y DAMA IAL DAMAGE OSS OF T OPPORTU A rA QS F E SUBJECT D IF THE UNI TE S CTION ut ic ate to State nited States of America sold ASAS and shall have NO product may be covered by a Guaranteed Protection rected dealer for details o lowing information A clear copy of the sales receipt showing the following 000000000 Date of purchase Your full name and address Au Type of alarm installed the plan or call Directed rom your authorized Directed horized dealer s company name and address Year make model and color of the automobile Au Vel All Insi jomobile license number security options installed allation receipts hicle identification number on automobile 920 0003 06 06 The company behind this system is Directed Electronics Since its inception Directed Electronics has had one purpose to provide consumers with the finest vehicle security and car stereo products and accessories available The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology
18. ESS MERCHANTABILITY FITNESS FO NFRINGEMENT OF INTELLEC DIRECTED NEITHER ASSUMES NOR AUTI FOR IT ANY DUTY OBLIGATION OR LIABILI DIRECTED DISCLAIMS AND HAS ABSOLU OF THIRD PARTIES INCLUDING ITS AUTH SECURITY SYSTEMS INCLUDIN l DIRECTED IS NOT OFFERI WARRA R PART G BE purchaser has not comple 10 days from the da or serial number is de modified or used in a manner contrary to its inte e use neglect improper service installation or other causes no arising out of defects in materials or construction T ation or removal of excessive damage and may refuse the re LOWED BY TY CULAR TUAL PROPERT HORIZE TYI TELY ORIZI G THIS UNIT A GU HEF VANDALISM DAMAGE OR THEFT O D AND HEREBY EXPRESSLY H 46 E AUI SCLAIMS ANY Directed Electronics Directed promises to the original purchaser to repair or replace at Directed s election with a comparable reconditioned model any Directed unit hereafter he siren the remote transmitters the associated which proves to be defective in workmanship or material under lifetime of the vehicle provided the following conditions are met rom an authorized Directed dealer the unit was professionally Directed dealer the unit will be professionally in which it was originally installed by an authorized Directed dealer and the unit is returned to Directed shipping prepaid with a legible copy of the proof
19. PYTHON Responder LC Model 951 Remote Start Keyless Entry Owner s Guide Liixected ELEctTRONIC S 2008 Directed Electronics Vista CA G4702P 2008 08 Contents Government regulations Warning Safety first What s included Important information Sy NOUR Warranty sek Slice AEE E Socvty tunity stn dunes les cuectacnrdtcaescetes Replacement remote ccceceeeesceeeeseeseesesteetsesseeeeetsenseniesesteenieneetesneetend Out of range notification Charging the Battery Low battery indicator Battery Replacement Multi car control capability Responder LE 2ways Sos sens ES NAER TAE EEA aaa ESAN KO TAWGY COMPONION Ae Hosoi EEE EE E EEE Transmitter configuration Usinig the syste ET EE AAE EATE Additional remote start features s s sisisieieieesisesieisisisisisieirieirisnirrnenrsrnnnnes Auxiliary features cece Remote control feature programming Remote setup options Menu option descriptions Pair remote setup Demo modes Safety TetUres ef esscnyapdkedete dd cneie sity TREN AA SAREAREN E ENE eie e TEENER iei Optional starter anti grind circuitry i Disabling the remote start system c ccccecseeseeseeteceseesenseeeeeesenseeeeeetenes Diagnostics Locking Unlocking Remote start Owner recognition Rapid resume logic Power saver mode Programming options Convenience expansions Glossary of terms Quick refere
20. T All installations must be performed by an authorized Directed dealer HE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION OPERAT ING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY YOU MUST IMMEDIATELY CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AU THORIZED Directed DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS This product is designed for fuel injected vehicles only Use of this product in a standard transmission vehicle must be in strict accordance with this guide 2008 Directed Electronics All rights reserved This product should not be installed in any convertible vehicles soft or hard top with a manual transmission Installation in such vehicles may pose certain risk 8 2008 Directed Electronics All rights reserved What s included One five button 2 way Supercode Responder LC Remote Control One five button 1 way Supercode companion remote The control module Control center with integrated status LED and Valet override switch A remote start defeat toggle switch Window decals Your warranty registration Congratulations on the purchase of your state of the art remote start system Due to the complexity of this system it must be installed by an authorized dealer only In
21. activated the horn horns if connected an the parking lights flash for 30 sec Panic mode can be disabled by pressing icon lock or unlock The system automatically checks for errors when it locks The 2 way remote beeps once and the parking lights flash once to confirm locking If no lock confirmation is received the remote LC displays the outofrange signal If errors are found when locking If the door was open at the time of locking you are notified of this active zone immediately after locking the system The horn in the vehicle honks again The 2 way remote control sounds a short error tone and the LCD displays the door icon Locking without the honk Silent Lock Press the button on the remote once and then press the bution The system locks without the confirmation honk The parking lights flash once The 2 way re mote displays the Mil icon If no lock confirmation is received the 2 way remote emits the Out Of Range signal 2008 Directed Electronics All rights reserved 15 Unlock Command Press one time to Unlock Feedback Unlock icon appears Notes The vehicle horn honks two times and the parking lights flash twotimes The door locks if connected unlock the 2 way remote beeps twotimes and the LCD displays the icon Unlocking without the honk Silent Lock Press the button on the remote once and then press the button The system unlocks without the confirmation honk The p
22. arking lights flash once The 2 way remote displays the icon If no unlock confirmation is received the 2 way remote emits the Out Of Range signal ga Remote Start Command Press one time to activate Remote Start Feedback Remote Start icon appears on screen The remote start tones play and parking lights flash Notes Before using the remote start be sure the vehicle is parked in a safe area with proper ventilation The preset remote start run time is 12 minutes This can be changed to between 12 and 60 minutes The system has a feature if programmed on that automatically notifies you when the runtime is running low When the system reaches 3 minutes and 1 min ute of runtime remaining it sends the 2 way remote control a paging signal 16 2008 Directed Electronics All rights reserved Points to remember If the hood is open or if the brake pedal is pressed the vehicle will not remote start The remote start shuts down When the brake pedal is pressed The hood is opened When the remote start command is sent again from a remote control When the runtime expires To drive your vehicle after it has been remote started 1 Get in without stepping on the brake 2 Insert the ignition key and turn it to the ON position 3 Now step on the brake The remote control will play the remote start shutdown tone You have now taken direct control from the remote start system Valet Take Over The Valet Take O
23. ash onetime when entering Valet take over Once you exit the vehicle you can lock the system and the car will remain running If the vehicle shuts down when locking then the unit did not enter valet take over mode Timer mode Command Press f hwotimes and then 2 Feedback Small timer icon displays and timer start on displays in the text area The parking lights flash 4 times fast to confirm Notes Enables or disables the remote start timer mode The system must be locked for the timer mode to operate The system will start every 3 hours for a maximum of six cycles until canceled by the brake hood or neutral safety shutdown wires The remote will respond with the Start and Stop remote start notification during each Start and Stop of the Vehicle while in Timer mode To activate timer mode with a manual transmission 1 Enter the MTS mode 2 Exit the vehicle lock the doors with the remote 3 Enter the timer mode The parking lights quickly flash 4 times to confirm entry into timer mode vehicle does not remote start at this point Vehicle begins the timer mode sequence To exit timer mode with transmitter e Press f twice and then press 2 Parking lights flash slowly four times confirming time mode is exited To exit timer mode without transmitter 1 Make sure the remote start system is not operating the engine 2 Turn the ignition on Timer Mode is exited and the parking lights flash slowly four times
24. d Electronics All rights reserved To activate turbo timer mode with a manual transmission 1 Enter MTS mode with the door open 2 Transmit the timer mode feature with the remote by pressing f twotimes and then AF 3 After exiting the vehicle lock the system and the vehicle remains running for the programmed runtime The remote start feature is still enabled You can still remote start the vehicle after the turbo timer has timed out and shut off the vehicle For safety reasons if a door is opened while the system is locked or unlocked while you are away the remote start exits the manual transmission mode and does not remote start until the MTS sequence is re initiated Note An optional push button can be hard wired to the H activation input H1 10 on the remote start This allows the user to activate the turbo timer without having to use the remote When the vehicle is running follow the procedures listed above but instead of pressing the remote press the push button the appropriate number of times to ac tivate the remote start factory setting is for 1 pulse The remote emits the remote start confirmation tone Now you can turn off the ignition and exit the vehicle The car remains running for the pre programmed amount of time 2008 Directed Electronics All rights reserved 25 Runtime check Command Feedback Notes Runtime reset While the remote start is running press f twotimes and then Hold for 1
25. d unlock are independent features that can be programmed separately e Panic mode enabled disabled when the ignition is turned on or com pletely turned Off Some states have laws against horns continually honk ing in moving cars 2008 Directed Electronics All rights reserved 39 e Comfort closure is a programming option which closes the vehicle s win dows after remote locking Note Comfort closure can only be used on cars that have the capability of closing the windows and on some cars the sunroof as well with the key cylinder in the door Listed below are some of the expansion options available Please consult your dealer for a complete explanation of all the options available to you Factory Alarm Trigger Notification This system has an input that can be connected to the horn circuit in the vehicle If the vehicle has a factory alarm and is controlled by this system for lock un lock the remote reports when the factory alarm has been triggered When the factory alarm is triggered the remote screen displays the alarm icon and alarm door open is displayed in the text area Note The remote must be in range and the system locked to receive the report The system does not report that the factory alarm has been triggered when unlocking with the remote Power Trunk Release The accessory output of the system can operate a factory power release for the vehicle s trunk or hatch Sometimes an optional relay is required
26. ection to the system An input can be provided by exist ing systems in the vehicle such as ignition or courtesy lights In vehicle status LED A light used to indicate the status of your system It is located on your systems control center Valet Button A small push button switch located on your systems control center It is used to override the starter interrupt when a 2 way remote is lost or damaged or fo enter or exit Valet Mode 2008 Directed Electronics All rights reserved Al LCD layout gt LCD remote features 42 Lock Locked in valet Unlock Unlocked in valet Alarm Remote Start Timer Mode Manual Transmission En abled 16 Thermometer Smart start Battery Status ood Trigger ood Zone bypass Trunk Trigger Trunk Zone bypass Pager On Pager Off 2008 Directed Electronics All rights reserved piz 18 g 19 g 20 3 Sia amp 22 10 s 23 5 2 24 oy 25 S S 26 g io 2 3 8 2 D S x 2008 Directed Electronics All rights reserved D A m Vibe On Pager Tone On Siren Silent Mode 2 Transmit Receive Out of Range Sensor Sensor Bypassed Car Door Zone bypass 27 28 29 30 31 32 33 34 9 9 E ALL Car Door ome Garage Open ome Garage Close Car 1 Car 2 All Zones Defroster Sound Wave
27. ew number of presses by your authorized dealer that number should be indicated below Override Switch Number 2008 Directed Electronics All rights reserved 21 Additional remote start features Manual transmission If the vehicle has manual transmission the proper steps must be followed before leaving the parked vehicle or the remote start feature is disabled aARWN gt No 8 9 10 Make sure the engine is running and the doors are closed Put the transmission in Press on the vehicle s Apply the emergency Release the vehicle s neutral oot brake brake oot brake Note Pressing the brake again after this step will disable the remote start feature Within 15 seconds activate the remote start from the remote The parking lights wi flash 5 times confirming that the remote start is ac tive If the parking lights don t flash then repeat steps 1 6 Turn off the ignition the car should stay running when key is turned off Exit the vehicle and cl Lock the doors with system ose the door he remote the vehicle shuts off when locking the You can now remote start the vehicle If a door is opened before the next remote start activation the system will not remote start 22 2008 Directed Electronics All rights reserved Note To enable Valet take over with a manual transmission open the door and enter into manual transmission mode as described above The parking lights fl
28. hresholds have been met If thresholds have been met then the remote start will start the vehicle and run for the pre programmed time It counts the first start as one successful start leaving 5 start cycles If the threshold has not been met then the system will not start the vehicle and 6 start cycles are left The unit continues to check threshold levels every 3 hours 28 2008 Directed Electronics All rights reserved Auxiliary features Aux 1 Command Feedback Notes Aux 2 Command Feedback Notes Aux 3 Command Feedback Notes Press f one time and then press Text displays the item activated This is an optional feature See your sales rep installer for details Press F two times and then press Text display the item activated This is an optional feature See your sales rep installer for de ails Press I three times and then press Text displays the item activated This is an optional feature See your sales rep installer for de ails Factory default is pulsed The text can be changed by your installer using the Bitwriter programming tool 2008 Directed Electronics All rights reserved 29 Remote control feature programming The Responder LC 2 way remote control has menus for configuring the remote control user features and for programming the remote to the system control mod ule Before you start make sure the keypad is unlocked See page 1 2 To p
29. lay temperature in Fahrenheit or Celsius e Button Press Beep On or Off Turn Off beeps when a button on the remote is pressed e System Type Remote Start amp Security or Remote Start Select the type of system you are using security system with remote start or a keyless entry system with remote start to ensure that the correct icons are displayed on the LCD e Clock Set To enter clock set mode Press the f button The LC text display reads hour to confirm entry in the clock set menu Press the button to move up the menu press the 2 button to move down the menu After you select the time increment hour min press F The hour or minute flashes Press the button to move up to the hour or minute and press the bution to move down to the hour or minute you want to set Once the desired time has been reached you can either choose back in the menu or press or BN to save and exit 2008 Directed Electronics All rights reserved 33 gt Pair remote mode lt is recommended that this feature for programming the remote to the system is performed by your installer gt Demo modes e Onetime with sound The LCD icons display one at a time with icon name displayed in the text field while the remote is playing tones e Onetime without sound The LCD icons display one at a time until they are all turned on The remote does not play any tones Note If the charger is plugged into the remote and demo mode is acti
30. lays in the text area when entering Valet mode Notes If the system is already locked the remote beeps one time when entering Valet mode When ex iting Valet mode the unlock icon appears solid Valet is displayed in the text area and the remote beeps two times The unlock icon is displayed but the doors stay locked To enter or exit valet mode with the valet program switch Turn the ignition key on and then off S i 2 a s At anytime during the next 10 seconds press and release the Valet switch Now the Status LED lights constantly if you S have entered Valet Mode and go out if you have exited xX Valet Mode Note The LED on the control center turns on solid when in Valet Mode and shuts off when exiting Valet Mode When locking the system in Valet Mode the screen displays valet and the remote then emits an error tone When unlocking in Valet Mode the screen displays valet and the remote emits two error tones 2008 Directed Electronics All rights reserved 19 Car finder Command Press ihreetimes and then o Feedback Remote beeps 1 short beep the vehicle emits 1 long horn honk if connected and the parking lights flash 10 times Notes Lock Unlock cancels the light flashes Cabin temperature Command Press f one time then Hold for 1 5 seconds Feedback Screen will display current in cabin tem perature Notes Cabin temperature is displayed on the
31. ler when using the Bitwriter To activate the Smart Start Mode with a manual transmission l 2 Enter the MTS procedure Exit the vehicle and press the button on the remote the vehicle will shut down when locking a Press the f button on the remote 3 times and then press the Ze button The 2 way remote will beep once and Smart Start On is displayed in the text area The parking lights on the vehicle will flash 5 times fast confirming entry into smart start mode The vehicle will now remote start when the cabin temperature reaches the programmed thresholds or when the vehicle battery reaches the pro grammed voltage The Smart Start Mode can be exited by following the activation procedure with the remote or can be deactivated manually by turning on the ignition or pressing the brake pedal in the vehicle The parking lights will flash 5 times slow confirm ing that Smart Start Mode is exited 2008 Directed Electronics All rights reserved 27 Details Smart start uses temperature and voltage settings to determine when the vehicle should start and run If any changes to temperature or voltage are made using the Bitwriter programming tool Smart start activation is affected The Smart Start function works similar to the Timer mode The system must be in the locked mode Using the system default settings it has a maximum of 6 starting cycles and checks the voltage cabin temperature every 3 hours to see if the t
32. lly enclosed area or when having the vehicle serviced the remote start system must be disabled using the installed toggle switch It is the user s sole responsibility to properly handle and keep out of reach from children all remote control transmitters to assure that the system does not unintentionally remote start the vehicle THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJA CENT TO THE VEHICLE ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED These precautions are the sole responsibility of the user Remote starters on manual transmission vehicles operate differently than those with automatic transmission because you must leave your car in neutral You must read this Owner s Guide to familiarize yourself with the proper procedures regarding manual transmission remote starters If you have any questions ask your installer or contact Directed at 1 800 753 0600 Before remote starting a manual transmission vehicle be sure to e leave the vehicle in neutral and be sure no one is standing in front or behind the vehicle e Only remote start on a flat surface e Have the parking brake fully engaged WARNING It is the responsibility of the owner to ensure the parking emergen 6 2008 Directed Electronics All rights reserved cy brake properly functions Failure to do so can result in personal injur
33. nce guide Limited lifetime consumer warranty Government regulations This device complies with Part 15 of FCC rules Operation is subject to the fol lowing two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesirable operation This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential instal lation This equipment generates and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television which can be determined by turning the equipment Off and ON the user is encouraged to try fo correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Remote Controls To satisfy FCC RF exp
34. nt areas ie Weather RF interference etc range may be affected and require you to be closer to the vehicle for successful transmission gt System maintenance The system requires no specific maintenance The 2 way remote contains a non replaceable rechargeable battery When the battery begins to weaken the operating range will be reduced Your way remote is powered by small coin cell lightweight 3 volt lithium bat tery that will last approximately one year under normal use The 1 way remote uses one CR2032 cell battery gt Charging the Battery e Plug in the USB charger alternately a standard mini USB cable connected to any standard USB port on any laptop or desktop computer can also be used cable not included e The LCD displays CHARGE while the battery level bars within the battery icon flash e When charging is complete the LCD then displays FULL Note If the battery has been severely discharged all remote functions are dis abled for a short charge period The battery status outline flashes and CHARGE is displayed on the LCD Once the battery has accumulated enough charge for functionality the LCD icons initialize with a beep sound the battery status 10 2008 Directed Electronics All rights reserved outline stops flashing and the remote becomes operational while still displaying CHARGE 32 F TO 1 Warning The temperature range over which AN the battery can be charged is O C TO 45 C
35. of purchase bearing the following in ormation consumer s he authorized dealers name telephone number on including accessories model of the vehicle vehicle license number and vehicle identifica hout limita and the associated sensors and accessories carry a one year warr L PRODUCTS RECEIVED BY DIRECTED FO the year make and ion number All com ion the siren the remote transmitters anty from the date o R WARRANTY REPAIR DENIED This warranty is nontransferable ed the warranty card e of purchase to the address listed on the aced missing or altered the unit has been nded purpose the unit has been damaged he warranty does not cover damage he unit Directed in its sole discretion wil urn of any unit with L WARRANTIES INCLUDING WARRANTY WARRANTY OF E AND WARRANTY OF NON EXPRESSLY EXCLUDED AND S ANY PERSON OR ENTITY TO ASSUME CONNECTION WITH ITS PRODUCTS O LABILITY FOR ANY AND ALL ACTS ED DEALERS OR INSTALLERS DIRECTED ARE DETERRENTS AGAINST POSSIBLE IARANTEE OR INSURANCE AGAINST TOMOBILE ITS PARTS OR CONTENTS LIABILITY WHATSOEVER INCLUDING LAW Al IMPLIE PURPO Y AR j vV U o mMm ive 1 2008 Directed Electronics All rights reserved TATI S Ol fas F TH OF LAW ILY To UNIT D INCLUD L DAMAGES OF EARNINGS OT RRANTY S AS gt
36. only after remote start is On The remote beeps onetime gt To disable the remote start system Move the shutdown toggle switch to the Off position Location of Shutdown Toggle Switch gt Valet Mode Press f twortimes and then BN The remote will beep once and the LCD displays valet when enabled When disabling the remote will beep twice and the LCD displays valet gt Valet take over 1 Before turning Off the engine press and release the button Then wait a few seconds 2 Turn the ignition key to the Off position 3 Exit the vehicle and lock the doors with the remote The engine will remain running until the programmed time elapses or a shutdown input is received 2008 Directed Electronics All rights reserved 45 Limited lifetime consumer warranty he unit excluding without limitation sensors and accessories reasonable use during the he unit was purchased installed and serviced by an authorized reinstalled in the vehicle bill of sale or other dated name telephone number and address and address complete product descripti ponents other than the unit including wi purchase of the same AL WITHOUT PROOF OF PURCHASE WILL and is automatically void if the original and mailed it within ten card the unit s date code by accident unreasonab o the unit caused by instal determine what constitutes excessive damage TO THE MAXIMUM EXTENT AL BUT NOT LIMITED TO EXPR
37. osure compliance requirements this device should be used in hand held hand operated configurations only The device and its antenna must maintain a separation distance of 20 cm or more from the person s body except for the hand and wrists to satisty RF exposure compliance This device is designed to be used in a person s hands and its operating configurations do not support normal transmissions while it is carried in pockets or holsters next to a person s body 4 2008 Directed Electronics All rights reserved Control Center To satisfy FCC RF exposure compliance requirements the device and its antenna must maintain a separation distance of 20 cm or more from the person s body except for the hand and wrists to satisfy RF exposure compliance Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device 2008 Directed Electronics All rights reserved 5 AS Waring Safety first The following safety warnings must be observed at all times Due to the complexity of this system installation of this product must only be performed by an authorized Directed dealer When properly installed this system can start the vehicle via a command signal from the remote control transmitter Therefore never operate the system in an enclosed area or partially enclosed area without ventilation such as a garage When parking in an enclosed or partia
38. rogram the remote user features Press and hold the f button on the remote for about 8 seconds ignore the car indicator at 3 seconds The status screen clears and Main Menu is displayed in the text display area of the screen Release the F button to display the Remote Options menu Options Description Remote Setup Allows feature programming of the remote Sensor Adjust Not available with this system Pair Remote Sets up remote for programming to the system Demo Mode Places remote in demo mode Exit Exits programming a Press he button to scroll up and press the button to scroll down the main menu From the Main Menu once a feature name is displayed in the text display area press and hold the f button until the remote beeps to confirm entry into the selected feature menu To access feature menu options scroll up pressing the button or scroll down by pressing the gt button When the feature that you want to program is displayed in the LCD text area press and hold the f for 1 second to save the feature The LCD screen returns to the previous options menu You can save and exit the programming mode anytime by pressing the or Q Programming mode is automatically exited without saving if there is no remote activity for 30 seconds Note Selecting Back returns to the previous menu without saving the setting 30 2008 Directed Electronics All rights reserved gt Remote setup options
39. stallation of this product by anyone other than an authorized dealer voids the warranty All dealers are provided with a preprinted dealer certificate to verify authorization By carefully reading this Owner s Guide prior to using your system you will maximize the use of this system and its features You can print ad ditional or replacement copies of this manual by accessing our web site at www directed com gt Your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase Your product warranty will not be validated if your warranty registration is not returned Make sure you receive the warranty registration from your dealer It is also necessary to keep your proof of purchase which reflects that the product was installed by an authorized dealer gt Replacement remote controls Your system comes with one Responder LC remote control P N 7752P and one companion remote control P N 7652P If additional remotes are desired please see your authorized dealer or visit www directedstore com to order 2008 Directed Electronics All rights reserved 9 gt Out of range notification If a command is issued from the remote but the remote is beyond the range of the vehicle to receive the command the remote will respond with an outof range notification If this occurs the outoFrange icon displays on the LCD and the remote emits an error tones Since conditions will vary in differe
40. ver feature allows the vehicle to remain running after the key has been removed from the ignition This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time but would like to leave the motor running and the climate controls on To enable Valet take over while the vehicle is running press SI time and the parking lights will flash after a couple of seconds turn off the ignition and the car should stay running Once you exit the vehicle you can lock the system and the car will remain running If the vehicle shuts down then the unit did not enter valet take over mode 2008 Directed Electronics All rights reserved 17 Aux Command Press and hold for 1 5 seconds to acti vate the Trunk Release Feedback The trunk icon appears and the remote plays a short tone Notes This is an optional feature See your sales rep installer for details The factory default screen displays the trunk icon and text The text can be changed by your installer using the Bitwriter programming tool f Function shift Command Press 1 to 4 times See Transmitter configuration table Feedback Display shows a text message across the bottom for the com mand received Notes Each Press then release shifts the function of the command but fon 2008 Directed Electronics All rights reserved Valet mode Command Press f twotimes and then Feedback Unlock icon appears hollow Valet dis p
41. y or prop Y properly p Ury OF prop erty damage We recommend the owner have the par ing emergency brake system inspected and adjusted by a qualified automotive shop bi annually Use of this product in a manner contrary to its intended result in property damage personal injury or death 1 mode of operation may Never remotely start the vehicle with the vehicle in gear and 2 Never remotely start the vehicle with the keys in the ignition The user must also have the ne vehicle periodically checked wherein the vehicle mus utral safety feature of the not remotely start while the car is in gear This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined i n the product installation guide If the vehicle starts in gear cease remote start operation immediately and consult with the authorized Directed dealer to fix the problem After the remote start module has been installed contact your authorized dealer to have him or her test the remote start module by performing the Safety Check outlined in the product installation guide If the vehicle starts when performing the Neutral Safety Shutdown Circuit test the remote properly installed The remote start module must be rem start unit has not been oved or the installer must properly reinstall the remote start system so that the vehicle does not start in gear OPERATION OF THE REMOTE START MODULE IF
Download Pdf Manuals
Related Search