PYLE Audio PLVRL6400 User's Manual
Contents
1. PYLE PLVRL6400 OWNER S MANUAL FLIP DOWN TFT MONITOR INSTALLATION Desk top Installation MA On Mounting Bolts M3x6 Levers Fig 1 Determine the mounting location and drill four mounting holes Attach the bracket to the holes with the tapping screws M4x10 Let the two levers aim at the fixing holes on the bottom of the base to fix the display unit Attach the TV unit to the preferred location with the mounting bolts M3x6 For the convenience of fixing the unit you can turn the display left or right to show the holes on the base See the arrowhead symbol named 1 When the installation has completed you can turn the display upward or downward left or right to adjust the viewing angle See the arrowhead symbol named 2 and 1 INSTALLATION Ceiling on Installation OPUN Fixing holes Mounting Bolts M3x6 Fig 2 Determine the mounting location and drill four mounting holes Attach the bracket to the holes with the tapping screws M4x10 Let the two levers aim at the fixing holes to fix the display unit Attach the unit to the bracket with the mounting bolts M3x6 When the installation has completed you can also turn the display upward or downward left or right to adjust the viewing angle See the arrowhead symbol REPLACING THE CAR DOME LAMP Follow the directions show below for anew2. lamp changing 1 Position light switch to Y 2 Push back the lamp cover and open it Refer to the following figure 3 Remove and discard the old lamp 4 Install a new bulb 5 Close the cover Lamp Cover Light Switch Bulb Specification Diameter o8mm Length 28mm Voltage Spec DC12V 5W CAR DOME LAMP WIRING Color Connection Red Power Supply White Interior Light Supply Black Ground CONTROL amp FUNCTION KEYS CONTROL amp FUNCTION KEYS 6 4 INCH TFT COLOR MONITOR MONITOR 10 11 12 POWER Press button 1 to turn on the unit Press it again to turn it off POWER INDICATOR LIGHT When the system is on the indicator light 2 will be illuminated CAR DOME LAMP The car dome lamp 3 will be on in some needed situations LIGHT SWITCH The are three seetings for the car dome lamp operation Y OFF Y AUTO and ON refer to light switch 4 A To turn off the lamp B Y To make the lamp turned on only when car doors are opened C amp To turn on the lamp REMOTE SENSOR Point the remote control handset to the remote sensor 5 Press the function keys on the handset to control the unit it would be worked for connecting the TV uni
3. t or DVD only SPEAKER VOLUME CONTROL KNOB Rotate the knob 6 clockwise or counter clockwise to increase or decrease the volume level of the speakerson the base of the unit When rotate the knob in the direction of volume decresing to the end it will turn off the speakers BRIGHT Rotate the bright knob 7 clockwise or counter clockwise to increase or decrease the screen brightness CONTRAST 0 Rotate the volume knob 8 clockwise or counter clockwis to increase or decrease the contrast lever of the screen display COLOR 8 Rotate the color knob 9 clockwise or counter clockwis to increase or decrease the color lever of the screen display TFT LIQUID CRYSTAL DISPLAY The 6 4 inch color TFT LCD 10 can show the current state of the unit EARPHONE VOLUME CONTROL KNOB Slide the knob 11 will change the volume of the earphone JACKS FOR EARPHONE There are two jacks 12 for earphone You can connect earphone to any one of the jacks to receive sound signal 13 14 15 16 17 18 19 PUSH Monitor Release Button Opening the Monitor Press the PUSH button 13 to eject the screen display from the base at a little angle Then you can easily turn the display upward or downward for good viewing The monitor also can be adjusted through 30 degree both left and right from the central viewing position Closing the Monitor Return the monitor to the central viewing position Then push the monitor back into
4. the monitor base unit until the screen engages with PUSH button 13 DISPLAY DIRECTION CONTROL SWITCH The switch 14 should be dialed to DWN side or UP side to adjust the direction of the picture display and get user s needed viewing effect DC 12V INPUT Through this jack 15 provide DC 12V power supply to the unit SENSOR When connect DVD unit or another unit to the monitor through these two jacks 16 you can control the DVD unit or another unit by pointing the remote contorl handset directly to the remote sensor 5 AV1 IN The group of jacks 17 is used for AUDIO R in anf AUDIO L in and VIDEO in AV2 IN The group of jacks 18 is also used for AUDIO R in anf AUDIO L in and VIDEO in AV SELECT SWITCH Slide the switch 19 to 1 side the AV1 IN 17 group is avaliable slide the switch 19 to 2 side AV2 IN 18 group is avaliable www pyleaudio com 8 88 T1341 03
Download Pdf Manuals
Related Search