PYLE Audio PLD53MUT User's Manual
Contents
1. Set Last Memory State I Speaker Setup Page DOWNMIX LT RT STEREO Set Downmix Mode This is to activate the audio output from DOLBY AC3 5 1 DOWNMIX to 2 channel mode Select the preferred SPEAKER connection by using the cursor buttons Select the LT RT to activate the Dolby surround compatible output Select the STEREO to activate simple stereo mode DOLBY DIGITAL SETUP lt Dolby Digital Setup DOLBY DYNAMIC Set DRC OFF 7 LAST MEMORY SETUP Select the LAST MEMORY output ON OFF 19 DYNAMIC RANGE CONTROL Select DRC and adjust the dynamic range of a Doby Digital encoded program There are 8 steps between full compression and off compression SETUP PREFERENCES SETUP PREFERENCES PAGE 8 145 Preference PAL TV Type Audio AUTO Audio Subtitle NTSC Subtitle Disc Menu Disc Menu Parental Parental Password Password Default Default OFF Set TV standard Preferred Subtitle Language 1 TV TYPE SETUP This player can play discs recorded in either PAL or NTSC format Select NTSC format when you co2. Do not warp discs Adisc should always be kept in its case when not in use to prevent from damaging e Do not place discs in the following places 1 Direct sunlight 2 Dirty dusty and damp areas 3 Near car heaters 4 On the seats or dashboard Disc Cleaning Use a dry soft cloth to wipe the surface If the disc is quite dirty use a soft cloth slightly moistured with isopropyl rubbing alcohol Never use solvents such as benzine thinner or conventional record cleaners as they mar the surface of the disc Note A disc may become somewhat scratched although not enough to make it unusable depending on your handle it and conditions in the usage environment Note these scratches are not an indication of any problem with the player Label side up Do not touch gt the underside of the disc 8 SN 2 2 e Do not 1 bend Wipe the disc from center toward the outside edge Preparing New Discs with Rough Spots new disc have rough edges its inside and outside edges lf a disc with rough edges is used the proper setting will not be performed and the player will not play the disc Therefore remove the rough edges in advance by using a ball point pen or pencil as shown on the right To remove the rough edges press the side of the pen or pencil againstthe inside and outside edges of the disc Rough spots on outside edge Ball point pen
3. then press ENTER button to confirm MAY AUG Pressing REPEAT button repeatedly can select three kinds of repeat play mode LY C14 Long fright REP ONE 4Zb eeseee Play the same song over and over again REPEATALL Y Play all songs in the current directory in sequence over and over again DISC REPEAT Play all songs in the discover and over again In the playback use ppl 44 to skip an item ahead or back In the playback face right or left swing the SEL knob 4 button more than 2 seconds on the front panel or short press pp 44 on the remote control to rapid forward reverse 14 BASIC OPERATION USB Operation A Plug the USB connect line to the USB socket see number 25 of the unit properly See fig 1 when the USB appliance connect to the USB port of the connect line the system star playing track of the USB appliance automatically B IN USB playing you can press the cursor button to select the item Then press ENTER button to playing also press numeric to play the corresponding track directly Press the PPI KK button to skip to the next track or skip to the back one track Press 44 button to fast forward or fast reverse Press the REPEAT button to select repeat play mode You can press the EJECT button to ejectthe disc or insert the disc into the compartment When insert the disc the unit will play the disc automatically C In USB mode when the disc in the uni
4. or pencil NV Rough spots oninside edge INSTALLATION NOTES Choose the mounting location where the unit will not interfere with the normal driving function of the driver Before finally installing the unit connect the wiring temporarily and make sure itis all connected up properly and the unit and the system work properly Use only the parts included with the unit to ensure proper installation The use of unauthorized parts can cause malfunctions Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle Install the unit where it does not get in the driver s way and cannot injure the passenger if there is a sudden stop like an emergency stop If installation angle exceeds 30 from horizontal the unit might not give its optimum performance 30 Avoid installing the unit where it would be subject to high temperature such as from direct sunlight or from hot air from the heater or where it would be subject to dust dirt or excessive vibration DIN FRONT REAR MOUNT This unit can be properly installed either from Front conventional DIN Front mount or Rear DIN Rear mount installation utilizing threaded screw holes at the sides of the unit chassis For details refer to the following illustrated installation methods INSTALLATION SS DASH BOARD HEX NUT METAL MOUNTING lt STRAP SPRING WASHER 0 CONSOLE Z 0 P
5. Change Password 6 PASSWORD Select the change and press ENTER button Type the old password The initial factory code is 1379 and key in 4 characters password now you want to use and retype again to confirm key in correctly 21 amp 5 CM Preference Page Preference Page TV Type 1KID SAF TV Type Audio 2G Audio Subtitle 3PG Subtitle Disc Menu 4PG13 Disc Menu Parental spes Parental 6R Password Password 17 Default Default RESET 8 ADULT OFF Load Fcatory Setting Set Parental Control 7 DEFAULTS Select reset to become factory initial setting DEFAULTS TABLE TV DISPLAY NORMAL LB ANGLE MARK ON GENERAL sETUP 250 LANGUAGE ENGLISH SPDIF OUPUT SPDIF RAM CAPTIONS ON SCR SAVER ON LAST MEMORY SPEAKER SETUP DOWNMIX STEREO DOLBY DIGITAL DYNAMIC OFF TV TYPE AUTO AUDIO ENGLISH SUBTITLE OFF PREFERENCES DISC MENU ENGLISH PARENTAL 8 ADULT PASSWORD 1379 SPECIFICATION GENERAL Supply Voltage Current Consumption SIGNAL SYSTEM DISCS PLAYED AUDIO SIGNAL OUTPUT CHARACTERISTICS RADIO FM TUNER SECTION Tuning Range IF Range Usable sensitivity 30dB AM TUNER SECTION Frequency Range IF Range Usable sensitivity 30dB TV TUNER TV System TV Sensitivity TFT MONITOR Monitor Screen Size Number of Pixels Color System NOTE 12 Dc 11v 15v More Then 10A Compo
6. 16 Multi Subtitle Language Function sss 16 Multt Angle F nctlon eame E 16 Title Menu Function 2 2 16 TV Operations OT UIT 16 17 General 17 Speaker SETUP anssi aem adage ae X 19 Dolby Digital Setup e rt ER ERR d e d 19 Preferences aps repe E iic rS RENE 20 Table eot Ia EP UU Ca 21 T EIE 22 Trouble Shooting 23 SAFETY INFORMATION CAUTION THIS DVD PLAYER ISACLASS I LASER PRODUCT HOWEVER THIS DVD PLAYER USES VISIBLE INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED BE SURE TO OPERATE THE DVD PLAYER CORRECTLY AS INSTRUCTED USE OF CONTROLS ORADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE DO NOT OPEN COVERS AND DO REPAIR YOURSELF REFER SERVICING TO QUALIFIED PERSONNEL WARNING TO REDUCE THE RISK OF FIRE OR
7. 2 seconds 10 BASIC OPERATION B To recall the preset memory press one of the preset buttons 1 6 C Press 1 TOP 6 button to select the first track chapter to play a In the state of VCD CD MP3 disc playing press the button on the front panel to select the first track chapter to play depend on the disc used for VCD b In the state of DVD disc playing the 1TOP button is not available D Long Press 2 RPT 7 button to select repeat mode as follow DVD VCD CD CHAPTER REPEAT ON gt TITLE REPEAT REP ONE REP ALLA 4 REPEAT OFF x ee 4 a Continuously repeat at the current chapter track when selected REP ONE mode b Select REP ALL mode to continuously repeat all chapter track on the current disc REPEAT feature does not support VCD2 0 with PBC ON E Long Press 3 INT 8 button to scan disc a In the state of CD disc playing press the 3 INT button to play the previous 6 seconds partof each track chapter on disc b In the state of Mp3 disc playing the 3 INT button is not available c In the state of VCD disc playing long press the 3 INT button the screen will display as follow long press it again will release this mode TRACK DIGEST DISC INTERVAL TRACK INTERVAL 1 you can use the 7 4 buttons on the remote control to select the item and then press the ENTER button to confirm 2 In Track Digest OR Disc Track Interval MODE You can u
8. mode after search channel automatically when you want delete the no sign channel press the SKIP button the screen display SKIP the channel will be deleted Also you can press numeric button to select channel then press SKIP to add channel the screen display SAVE SETUP GENERAL SETUP GENERAL PAGE V BA General setup page General setup TV Display LB Angle Mark ON OSD Lang ENG Spdif Output SPDIF RAW Captions ON Screen Saver ON Last Memory ON TV Display Normal PS Angle Mark Normal LB OSD Lang Wide Spdif Output Captions Screen Saver Last Memory Go To General Setup Page Set TV Display Mode 1 Press SETUP button on the remote control 2 The SETUP menu is displayed 3 Select the preferred item by using the 4 buttons 4 Press ENTER button a GENERAL SETUP This setup page includes the item of TV display amp audio output feature The detail please refer to GENERAL SETUP MENU b SPEAKER SETUP This is to activate the audio output from DOLBY AC3 5 1 DOWNMIX to 2 channel mode Please refer to SPEAKER SETUP MENU c DOLBY DIGITAL SETUP Please refer to DOLBY DIGITAL SETUP d PREFERENCE SETUP This setup page includes all the configuration of support feature The detail please
9. ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING INTERFERENCE USE ONLY THE RECOMMENDED ACCESSORIES THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION This product incorporates copyright protection technology that is protected by method claims of certain U S Patents and other intellectual property rights owned by Macrovision Corporation and other rights owners Use of this copyright protection technology must be authorized by Macro vision Corporation and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation Reverse engineering or disassembly is prohibited REGION MANAGEMENT INFORMATION This DVD Player is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc If the Region number described on the DVD disc does not correspond to the Region number of this DVD Player this DVD Player cannot play this disc DISC NOTES Disc formats supported by this player DVD 12 disc Single sided disc only ess VideoCD 12 cm disc COMPACT CD 12 cm disc Me MP3 CP 45cm disc Discs which cannot be played with this player e DVD ROM e DVD R DVD RAM e CDV e CD G Handling and Cleaning e Dirt dust scratches and warping disc will cause misoperation e Do not place stickers or make scratches on discs
10. GREY FRONT FRONT Lch SPK WHITE BLACK GREY BLACK Reh SPK REAR GREEN VIOLET REAR Lch SPK Rch SPK GREEN BLACK VIOLET BLACK REMOTE CONTROL 1 CLK 2 MODE 3 STOP 4 SETUP 5 MO ST AUDIO 6 SUBTITLE LO DX 7 8 GOTO 9 44 gt gt 10 SEL 11 VOL VOL 12 7 4 13 MENU SUB WOOFER 14 BAND OSD 15 POWER 16 PLAY PAUSE 17 MUTE 18 TITLE PBC AIP 19 20 ANGLE 21 EQ 22 SEARCH 23 ENTER 24 SKIP 44 25 0 9 26 10 eE o o He n TEE amp 2 a amp Lcec amp elc ee SS Press it to change the display to clock display Press it to change between TV RADIO DISC and AUXIN mode Press it to stop playback Display the SETUP menu In radio mode press it to select STEREO or MONO mode In disc mode press it to changing of the AUDIO soundtrack on multi audio soundtrack DVD disc Changing of the sound mode of the VCD CD disc Changing ofthe SUBTITLE language on multi subtitle language DVD disc In radio mode Press this button for distance reception when you are located at weak signal location depress for stronger signal Switch the Repeat mode of DVD VCD CD MP3 dis
11. LAIN WASHER 9 SLIDE BRACKET TAPPING SCREW E 2 HOUSING KEY PLATE PLASTIC COVER KEY PLATE If you want to take CHASSIS out of the SLIDE BRACKET HOUSING first remove the PLASTIC COVER of the both sides away then insert the two KEY PLATE into left and right side of chassis as above illustration CHAGNE ANGLE CHANGING THE CONTROL PANEL ANGLE When you want to change the angle to play you can press repeatedly the 2 angle button to select the desired angle as follows Angle 4 Caution Do not insert your finger behind the control panel ELECTRIC CONNECTION WIRING CONNECTION WHITE B 12V REAR CAMERA SWITCH GREEN 5 PARKING BRAKE TV ANT IN YELLOW REAR CAMERA INPUT AUX optional VIDEO IN YELLOW lt ANTENNA CONNECTOR SSS RCH IN RED LCH IN WHITE RCA CABLE GREY SUBWOOFER Saat IGNITION RED f emp OUT2YELLOW SWITCH B REAR RCA OUTPUT COAXIAL OUT BROWN CABLE optional RCH RED MEMORY YELLOW FRONT RCA OUTPUT WHITE CABLE FRONTRCARED R GROUND B S l VIDEO OUT 1 YELLOW FRONT RCA WHITE L FOR RCALINE OUT VERSION ONLY xus FUSE ANTENNA BLET WHITE
12. PYLE PLD53MUT OWNER S MANUAL Mobile Video System 007 S U 0 000 fA 0 1 e Motorized Slide Down Panel e 2 TFT Color Monitor Car DVD VCD CD MP3 Player TV Tuner AM FM Digital PII Tuning Radio Player USB Connect Remote Control www pyleaudio com 5 2 DISC Notes ooo EO 3 Installation PL 4 IERnPRIE DPI 6 Electric Connectioh r nur cea rcu 7 Remote cre xh eh teta 804 ERA 8 4 cc 10 MP3 WMA JPEG Disc Play docte rice imn eed Una re Ed 13 AUX ODSEFAEIOD Soie 13 Monitor ODperatlOD c dass din ern str Eder cet a Urn cbe vata bun ulia tad 14 Rear View Camera ies nes 14 MPEG4 DISC 14 Tm 15 On Screen Display Function 0 15 Multi Audio Language Function
13. c Disc search button cooperatively used with numeric buttons Press to skip to the next track amp press to skip back one track Note In DVD mode press continually theK twice to skip back one track Press repeatedly to change mode through volume bass treble balance fader color bright contrast and tint modes Press itto adjust volume level Cursor buttons in MENU mode Note For models without built in FM Modulator the V buttons can be used for volume up down control In TV mode press p gt 4 tofinetune Pressthe V to select channel upward and downward Press itto display the root menu ofthe DVD disc Press and hold for more than 2 seconds can have SUBWOOFER press it again for more than 2 seconds to release this mode Display statistical disc information during playback To change the band in radio stations Press itto turn on the unit press it again to turn off Press once to pause a play press again to resume playback Press itto mute down sound Display the TITLE menu that is stored in DVD disc changing between PBC ON and PBC OFF on the VCD disc Auto store and preset scan function in radio stations Press to change the view angle Changing ofthe view angle on multi angle DVD disc Press it toturn to equalization function In TV mode Press itto search TV channel automatically In DISC mode Press itto start forward rapidly Confirm the Track Chapter selected with the number key or selecte
14. ck white The color system is set incorrectly Please switch to correct color system from menu No television video image appears The unit is not connected to the parking brake detection switch Make proper connection according to wire connection The parking brake is not engaged For safety reasons no television video images are displayed while the vehicle is moving Engaging the parking brake will cause images to be displayed No color in picture The disc format is not accordingto the TV set used PAL NTSC Please the television mode of the choice accommodation JPEG disc can not be played No JPEG files are recorded on the disc Change the disc back in a compliant formant JPEG files are not recorded Change the disc Record JPEG files using a compliant application The operation keys do not work The built in microcomputer is not operating properly due to noise Press the RESET button Front panel is not properly fixed into its place The radio does not work The antenna cable is not connected Insert the antenna cable firmly The signals are too weak Select a station manually 23 888 J3001 16
15. d with the cursor buttons on TV screen In TV mode press itto ADD and DELETE channel In DISC mode press itto reverse rapidly Numeric buttons Tens digit select button cooperatively used with numeric buttons 8 REMOTE CONTROL Preparing the Remote Control Inserting the Batteries 1 First push to inside as the direction indicated by the arrow See 0 then Remove the battery holder as the direction indicated by the arrow See 2 Replace the battery Set a new battery property with side up as illustrated See 3 Insert the battery holder Push in the holder to the original position See Using the Remote Control Face the remote control towards the player front face IR mark remote control signal receiver Operation angle About 30 degree in each the direction of the front of the IR mark To prevent damage to the unit be sure to follow the connection diagram page 7 BASIC OPERATION 449 020369 7 OOOO 3 aga 1 PWR BUTTON Press it to turn on the unit Press it again to turn off 2 3 VOL VOL amp SEL BUTTON Press sel button repeatedly to change mode through volume bass treble balance fader color bright contrast and tint modes Face up or down swing the SEL knob VOL VOL to adjust the selected mode The corresponding value will show on the display When mode has not been adjusted for sev
16. e back of the front panel 23 AUX INPUT JACK When the unit connect external A V you can press MODE to switch the AUX input mode MP3 WMA JPEG DISC PLAY 1 When inserting an MP3 WMA JPEG disc Ex When Mp3 file is detected 9 Current track file highlighted bar 00 56 04 07 C y Current track file number total number of tracks files in the current 2 003 112 Repeat folder x Elapsed playing time of the current 3 track not available for JPEG disc playing time not available for D Mp3 woman 1 JPEG disc 5 Selected playback mode Mp3 new ton Operation mode icon Play 24 2 7021 v E stop pause P forward 4 reverse In stop mode useA V gt 4 remote control to select the item or folder then press ENTER button to confirm Pressing REPEAT button repeatedly can select two kinds of repeat play mode 2 REP ONE Play the same song over and over again 3 REP ALL Play all songs in the discover and over again In the playback use PPI or to skip an item ahead or back In the playback face right or left swing the SEL knob 4 button more than 2 seconds on the front panel or short press gt 44 on the remote control to rapid forward reverse 13 BASIC OPERATION TFT MONITOR OPERATION 1 Press the SEL button 3 repeatedly during DVD VCD mode to display the adjustm
17. ent items on the screen 24 and then face up or down swing the VOL buttons to adjust the selected item The corresponding value will show on the display gt Volume gt Bass gt Treble Balance Fader Tint Contrast Bright Color 2 ADJUSTABLE ITEMS COLOR 0 to 32 Adjust the color fo the picture lighter or darker BRIGHT 0 to 32 Adjust if the picture is too bright or too dark CONTRAST 0 to 32 Adjust the contrast of the bright ans dark portion TINT 0 to 32 Adjust the tint if the human skin color is unnatural Adjustable when NTSC is selected for NTSC PAL The function of the VOLUME BASS TREBLE BALANCE and FADER Please see page 10 REAR VIEW CAMERA When connecting the rear view camera the mirror image of the rear view through the rear view camera is automatically displayed on the monitor when you change the gear to the back position The monitor on the unit only NOTE for the brake function if the parking brake is not engaged parking brake flashes on the monitor and no playback picture will be shown only the audio will be heard This warning appears only when the parking brake wire is connected to the parking brake system built in the car See page 7 MPEG4 DISC PLAY MPEG4 disc is playing as the format of FILE For example 00 56 0407 gt In stop mode use 4 onthe 001 001 Repeat one remote control to select the item
18. eral seconds display returns to normal radio or CD display gt Volume gt Bass gt Treble Balance gt Contrast Bright Color e A Volume Adjust volume level by using VOL VOL button Note The unitis initially set to volume mode B Bass Press SEL button one time Adjust bass level by using VOL VOL button C Treble Press SEL button two times Adjust treble level by using VOL VOL button D Balance Press SEL button three times Adjust sound balance between left and right speakers by using VOL VOL button E Fader Press SEL button four times Adjust sound balance between front and rear speakers by using VOL VOL button NOTE the function of the Color Bright Contrast and Tint Please see 14 page 4 BAND BUTTON In RADIO mode press the BAND button on the front panel or on the remote controller to select your desired radio band and word which band is selected will be displayed on LCD Press itto change the bands as below FM gt MW gt LW FM gt MW FM gt AM For 3 Bands Europe For 2 Bands Europe For 2 Bands USA 5 EQ BUTTON Press it to turn to equalization function and to select desired audio mode There are four kinds of mode as below JAZZ gt CLAS gt POP ROCK J 4 6 7 8 9 10 11 PRESET STATION A To memorize the current frequency press any one of the six preset buttons 1 6 on the front panel or on the remote controller hold for more than
19. l not appear 4 SPDIF OUTPUT This is to activate the audio output from SPDIF OFF mode to SPDIF RAW mode to SPDIF PCM mode 3 WE SV 16 General setup page General setup page TV Display TV Display Angle Mark English Angle Mark OSD Lang French OSD Lang Spdif Output German Spdif Output ON Captions Spanish Captions OFF Screen Saver Italian Screen Saver Last Memory Portuguese Last Memory Set OSD Language Closed Caption 3 0SD LANG TYPE SETUP Select the preferred OSD language by using the V buttons 5 CAPTIONS SETUP Activate the CAPTIONS feature by selecting ON And release this feat ure by selecting OFF SETUP fas SPEAKER SETUP SPEAKER SETUP PAGE General setup TV Display Angle Mark OSDLang Spdif Output Captions Screen Saver ON Last Memory OFF Screen Saver 6 SCR SAVER SETUP Select the SCR SAVER output ON OFF ai General setup TV Display Angle Mark OSD Lang Spdif Output Captions Screen Saver ON Last Memory OFF
20. nnected to NTSC TV Select PAL format when you connected to PAL TV Select AUTO format the player TV output format will according to the DVD disc format m Preference Page TV Type English Audio French Subtitle Spanish Disc Menu German Parental Italian Password Portuguese Default Preferred Audio Language 2 AUDIO LANGUAGE SETUP Select the preferred AUDIO sound track by using the cursor buttons 3 SUBTITLE LANGUAGE SETUP Select the preferred SUBTITLE language by using the cursor buttons ex EA Preference TV Type Subtitle French Disc Menu Spanish Parental German Password Italian Default Portuguese Preferred Menu Language 4 DISC MENU LANGUAGE SETUP Select the preferred DISC MENU language by using the cursor buttons SETUP 5 PARENTAL Select suitable parental guidance by the cursor buttons and conformed by pressing ENTER button amp LA Preference Page TV Type Audio Subtitle Disc Menu Parental Password CHANGE Default
21. refer to PREFERENCES SETUP MENU TV Screen Video Material Wide 16 9 Normal Pan Scan Letter box ERO EC sed 1 TV DISPLAY SETUP This is to select the appropriate TV aspect 4 3 or 16 9 according to the connected TV set Normal PS For 4 3 TV Played back in the PAN amp SCAN style If connected to wide screen TV the left and right edges are cut off Normal LB For 4 3 TV Played back in letterbox style If connected to wide screen TV black bands appear at top and bottom of the screen Wide For 16 9 TV Select when a wide screen TV setis connected 4 3 DOLBY Cc ru gt General setup page General setup page TV Display Angle Mark ON OSD Lang OFF Spdif Output Captions Screen Saver Last Memory TV Display Angle Mark Osd Lang SPDIF OFF Spdif Output SPDIF RAW Captions SPDIF PCM Screen Saver Last Memory Set Angle Mark Setup SPDIF 2 ANGLE MARK DISPLAY SETUP If itis set to ON when the multi angle DVD disc is playing the angle mark will appears on the screen if is setto OFF the mark wil
22. s OSD for the third time TOTAL ELAPSED TRACK 01 16 00 60 d Press OSD for the fourth time TOTAL REMAIN TRACK 01 16 78 46 BASIC OPERATION e Press OSD for the fifth time The message on the screen will be cleared for SVCD and VCD C Example for MP3 Each time OSD is pressed the message displayed on screen changes as follows 2 ELAPSED gt SINGLE REMAIN Multi audio Language Function For DVD Press AUDIO during playback Each time the button is pressed number of the audio soundtrack language changes on sequential order NOTES The language number is different according to the disc Some disc only contain one language soundtrack When no different language soundtrack are recorded amp willbe display at screen left top corner For VCD CD Press AUDIO during playback Itis possible to switch the sound between monaural and stereo sound MONO LEFT RIGHT Ba anu Title Menu Function For DVD If the DVD has multiple titles recorded on the disc It can select preferred title from the title menu to start playback Press TITLE during playback The title menu is display Press the cursor button shown in TV screen select preferred title by the cursor button and confirmed by ENTER key For VCD Press TITLE PBC button on the remote control while the disc is playing you can Switch between PBC on and PBC off mode Multi subti
23. se the 4 buttons to select the items and then press the ENTER to confirm You can also select the items using the corresponding number buttons and then press the ENTER to confirm d In the state of DVD disc playing long press the 3 INT button the screen will display as follow long press it again will release this mode SELECT DIGEST TYPE TITLE DIGEST CHAPTER DIGEST TITLE INTERVAL CHAPTER INTERVAL 1 You can use theA V gt 4 buttons on the remote control to select the item and then press the ENTER button to confirm 2 In Title Chapter Digest OR Title Chapter Interval MODE You can use the 4 buttons to select the items and then press the ENTER to confirm You can also select the items using the corresponding number buttons and then press the ENTER to confirm F Long Press 4 RDM 9 to play disc in random In the DVD VCD CD MP3 disc playing press the 4 RDM button on the front panel to play in random depend on the disc used for VCD 11 BASIC OPERATION 12 AS PS BUTTON When shortly pressing the APS button on the front panel or the A P button on the remote controller the radio searches for each preset station When the field Strength level is more than the threshold level of stop level the radio is holding at that preset number for few seconds with releasing mute and then searches again In FM band FM 1 FM 2 and FM 3 is checked one time When long pressing the APS or A P button more
24. sitive Video 1 0vp p 75Q 1 Dvd video Disc 5 12 Cm Single sided Single layer 5 12 Cm Single sided Double layer 2 Compact Disc cd da Video Cd 5 12cm Disc 2ch amp 4ch Line Out 1 Frequency Response 20Hz 20Khz 2 S n Ratio 90 Db jis 3 Wow And Flutter Below Measurable Limits 87 5 107 9MHz 10 7MHz 15dB 530 1710KHz 450KHz 45dB NTSC or PAL 459 V CH25 in average 2 5 Inch Wide 480 X 234 pixes NTSC PAL Specifications and design are subject to modification without notice due to improvements in technology 24 TROUBLE SHOOTING Before going through the check list check wiring connection If any of the problems persist after check list has been made consult your nearest service dealer SYMPTOM CAUSE SOLUTION If the power supply is properly The carignition switchis connected to the car accessory No power noton terminal switch the ignition key to ACC The fuse is blown Replace the fuse Disc can not be loaded or ejected player Presence of disc inside the Remove the disc in the player then put anew one direction Inserting the disc in reverse Insert the compact disc with the label facing upward The disc is extremely dirty or defective Clean the disc or try to play a new one Temperature inside the car is too high Cool off or until the ambient temperature return to normal Television video imageappears bla
25. t Press the STOP button once and then press the GOTO button the unit will change the DISC mode to play In DVD VCD CD mode Press the STOP button twice and then press the GOTO button the unit will change the USB mode to play In MP3 mode press the STOP button once and then press the GOTO button the unit will change the USB mode to play Note a To prevent damage to the USB during the playback don t pull out b In the state of the DISC playing Best to pull out the USB USB port 15 On Screen Display Function Press the OSD button during playback to display the contents of the current disc on the screen A Example for DVD a Press OSD forthe first time TITLE ELAPSED TT01 01 CH 01 38 0 02 06 Title Number Total Title Number Chapter Number Total Chapter Number of this Title of the disc currently being played will be shown on the screen along with the elapsed time b Press OSD for the second time TITLE REMAIN 01 01 CH 01 38 3 24 36 c Press OSD for the third time CHAPTER ELAPSED TT01 01 CH 01 38 0 02 56 d Press OSD for the fourth time CHAPTER REMAIN TT01 01 CH 01 38 0 04 32 e Press OSD for the fifth time The message on the screen will be cleared B Example for VCD SVCD CD a Press OSD for the first time SINGLE ELAPSED TRACK 01 16 00 49 b Press OSD for the second time SINGLE REMAIN TRACK 01 16 02 45 c Pres
26. than 1 second the radio searches from the current frequency and checks the signal strength level until 1 cycle search is finished And then 6 strongest stations are preset to the corresponding preset number The AS operation is implemented in the each band of selected band When the AS operation is finished the radio executes the preset scan 13 MU BUTTON Press it to mute down sound Press it again to release this mode and recover previous volume level A 14 y ANGLE BUTTON Press it to change the view angle you can adjust the angle for your desired 15 CLK BUTTON Press itto change the display to clock display Press it again to return to previous display In clock display press and hold for about 2 seconds until the hour display flashes Face up or down swing the SEL Knob VOL to adjust hours press CLK button to flash minute then use VOL VOL to adjust minutes 16 BUTTON Pressing pq during playback will stop play temporary Return to normal playback press once again 17 4 gt gt I BUTTONS A When face right or left swing the SEL 4 button more than 2 seconds during play The speed of rapid forward reverse changes according to the disc as follow DVD VCD CD MP3 r Normal Playback 2x 4x gt 8 gt 16x B Face right or left swing the SEL knob the K button during playback to skip to next track or back one track Note In DVD mode face left swing continually the SEL knob
27. the button twice during playback to skip back one track Note For some VCD 2 0 dics PBC playback control and 4 buttons may be unavailable C Press UP or DN button on the remote controller or face right or left swing the SEL knob M on the front panel to manually tune up or down for your desired station Press them hold for more than 2 seconds to automatically tune up or down for the stronger station 18 MOD BUTTON Press it repeatedly select TV AUX IN RADIO and DISC mode In USB during playback you can press STOP button and then press the GOTO button to select the DISC mode 19 BUTTON Press the eject button to turn downward the front panel and ejectthe disc from the disc compartment Also you can insert the disc to the compartment 12 BASIC OPERATION 20 ST BUTTON Press ST button to select STEREO or MONO reception for radio stations 21 MENU BUTTON Press it to display the root menu of the DVD VCD Only when PBC notin use disc 22 RESET BUTTON RESET button is placed on the housing and must be activated with either a ballpoint pen or thin metal object The RESET button is to be activated for the following reasons A Initial installation of the unit when all wiring is completed B All the function buttons do not operate C Error symbol on the display Note If press RESET button the unit can t work yet please use a cotton swab soaked in isopropyl alcohol to clean the socket on th
28. tle Language Function for DVD Only Press SUBTITLE during playback Each time the button is pressed number of the subtitle language changes in sequential order Notes The language number is different according to the disc Some discs only contain one subtitle language When no different subtitle language are recorded will be displayed at screen left top corner Multi angle Function for DVD Only Press ANGLE during playback Each time the button is pressed number of the angle changes in sequential order Notes The angle number is different according to the disc The function only work for disc having scenes recorded at different angles When no different angle are recorded W will be displayed at screen left top corner TV Operation Switching to TV mode 1 Connect the TV antenna to the TV IN from Ant jack on the back of the unit 2 Press the mode button on the remote control to select the TV mode Auto searching TV channels Press the SEARCH button on the remote controller to star search channel automatically Selecting channel Press the A w button to choose the channel upward and downward The numeric button 0 9 allow you to select the corresponding channel directly Note In TV mode the 10 button is not available Fine TV channel You can press gt 4 button on the remote controller to fine TV channel It can be improve the picture quality Channel ADD DEL In TV
Download Pdf Manuals
Related Search