Proxima ASA VCC-5775P User's Manual
Contents
1. Note The polarities for the 24 V AC and the 12 V DC input connectors are indicated on the rating label found on the unit back panel AC24V _ GND pc i2vs fi Push to insert the cable DC 12 V connection e DC12V Gog og OO eng CONNECTIONS The peripheral devices VCR monitor lens etc and cables are sold separately 1 Make the video signal connection between the camera and the monitor or timelapse VCR 2 Power supply choices e Use a commercially available 24 V AC adaptor Make sure to use a cable with an earth line 22AWG or more to connect to the earth connector Fig 1 e When using a DC 12 V power supply make the connections as indicated in Fig 2 CAUTION To prevent camera and or power supply failure pay close attention to polarity when making the connections 3 Insert the plug of this power supply into a wall outlet Adjust the picture on the monitor using the Brightness and Contrast controls W Coaxial cable type and maximum length e Cable type RG 59U 3C 2V 250 m maximum e Cable type RG 6U 5C 2V 500 m maximum e Cable type RG 11U 7C 2V 600 m maximum Note Use CCTV Video grade coaxial cable 10 English FLANGE BACK ADJUSTMENT screw English 11 If the pick up surface is not correctly positioned with relation to the lens focal point the picture will be out of focus in2. C mount type lens Install the supplied C mount adaptor on the lens mount then carefully align the lens mount with the camera opening and turn the lens slowly to install it 3 Connect the lens plug to the lens iris output connector LENS on the side of the camera The plug shape may not correspond to the terminal on the camera In such a case remove the original plug and using a soldering iron connect the supplied lens iris plug according to the diagram Refer to page 8 CS mount type lens English 7 MOUNTING THE LENS im 1 DN mp E 3 Pin layout Brake coil Brake coil Drive coil Drive coil E Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable Cut the cable at the plug then remove approx 8 mm of the cable sheath and strip about 2 mm from each wire 2 Install the lens iris plug Solder the cable to the pins following the correct pin layout refer to the table and illustrations then close the plug cover i Compatible auto iris lenses 1 3 inch COSMICAR DC type lens e Standard angle f 8 mm TS812E Equivalent e Wide angle f 4 mm TS412E Equivalent e Ultra wide angle f 2 8 mm TS212E Equivalent 8 English CONNECTIONS Basic connection for monitoring or recording gt gt gt Li lt i lt Video signal connections s VIDEO IN D gt VIDEO OUT English 9
3. particular when using auto iris power zoom lenses sold separately If that is the case adjust the flange back position as described below 1 Before installing the lens check that the two flange back lock screws have been tightened If the flange back lock screws are loose the CS mount ring will not be secured and it will not be possible to adjust the flange back 2 Fully install the lens then loosen the two flange back lock screws 3 Set the zoom lens to the maximum telephoto position TELE then set the focus using the focus ring on the lens 4 Set the zoom lens to the maximum wide angle position WIDE then set the focus by turning the CS mount ring 5 Repeat steps 3 and 4 until the image stays in focus when changing from a telephoto shot to a wide angle shot When the setting is complete tighten the flange back lock screws SETTINGS H Line phase adjustment When using a camera switcher to connect 2 cameras or more to one monitor there may be a vertical roll of the images when switched In such a case set as described below 1 Set the Sync switch to the L L position 2 Switch the display on the monitor from camera 1 to camera 2 Adjust the LINE PHASE volume on camera 2 until the vertical roll of the image stops If more than two cameras are used please repeat this procedure for all the cameras CAUTION If the vertical roll cannot be corrected by setting the LINE PHASE volume on camera 2 try setting the LINE PHASE
4. INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D INSTRUCTIONS 16 Ait AA COLOUR CCD camera CCD Farbkamera Cam ra CCD COULEUR amp CCD RAL About this manual Before installing and using the camera please read this manual carefully Be sure to keep it handy for later reference Uber diese Bedienungsanleitung Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der Kamera zuerst diese Bedienungsanleitung sorgfaltig durch und bewahren Sie sie zum spateren Nachschlagen auf SANYO VCC 5775P A propos de ce manuel Avant d installer et d utiliser la cam ra veuillez lire ce manuel attentivement Gardez le a port e de main pour toute r f rence ult rieure RFEA ERRAR H EH 01 WATARA EA Ba P FSO AAA UAB D sen Depending on the conditions of use installation and environment please be sure to make the appropriate settings and adjustments If you need help with installation and or settings please consult your dealer English 1 CONTENTS PRECAUTIONS cccseeeeesssseeees 3 PARTS NAMES 0 cccsesseeessseeeees 5 MOUNTING THE LENGS 0 7 CONNECTIONG ce eccecsteeeeeeeenees 9 FLANGE BACK ADJUSTMENT 11 SETTINGS 0 cc eecescsteeeessseseeeeeennes 12 TROUBLESHOOTING 00 15 SPECIFICATIONS cccsseesseessee 16 ACCESSORIES cssccseeesessseeeeeees 18 FEATURES Built in interline transfer method 1 3 CCD ap
5. d to your dealer or Sanyo Authorized Service Centre SPECIFICATIONS Scanning system PAL standard 625 TV lines 25 frames sec Interlace 2 1 interlace Image device 1 3 inch solid state image device CCD Picture elements 798 H x 584 V Effective picture elements 753 H x 582 V Synchronizing system Manual internal sync Line lock switching Resolution 480 TV lines horizontally 400 TV lines vertically Video output level 1 0 Vp p 75 ohms composite Video S N ratio More than 48 dB Minimum required illumination incandescent lighting Approx 1 4 lux with a F 1 2 lens Backlight compensation ON condition only Electronic iris function Manual ON OFF switching Electronic iris range 1 4 lux to 70 000 lux F 1 2 lens 2 0 lux to 100 000 lux F 1 4 lens Flange back 12 5 mm 0 5 mm White balance ATW Lens mount CS mount Environmental conditions Temperature 10 C 50 C Humidity less than 90 no condensation Power supply 24 V AC or 12 V DC Power consumption 24 V AC 50 Hz 3 2 W with auto iris lens 2 5 W without auto iris lens 4 0 W with auto iris lens 2 7 W without auto iris lens Weight Approx 160 g without lens 12 15 V DC 16 English SPECIFICATIONS E Dimensions mm Features and specifications are subject to change without prior notice or obligations English 17 ACCESSORIES C mount adaptor 5 mm 1
6. do not use an auto iris lens If used under fluorescent light the image may flicker In such a case change to incandescent lighting or set the El switch to the El OFF position and use an auto iris lens e When shooting bright subjects pay attention to the light angle in order to avoid or minimize the smear phenomenon effect 14 English TROUBLESHOOTING Before taking the camera for repairs please check below to make sure that the camera is used correctly If it still does not perform correctly please consult your dealer or a Sanyo Authorized Service Centre No picture on the monitor screen s the power turned on to all connected devices s the voltage correct Are all the signal connecting cables correctly connected s the lighting sufficient Has the lens cap been removed s the iris control correctly set The picture is not clear s the monitor correctly adjusted s the flange back position correctly set s the lens focus correctly adjusted Are the lens surfaces clean If there is dust or finger prints on the lens the image quality will deteriorate To clean the lens use a soft cloth or a commercially available lens cleaning set English 15 SERVICE This camera is a precision instruments and if treated with care will provide years of satisfactory performance However in the event of a problem the owner is advised not to attempt to make repairs or open the cabinet Servicing should always be referre
7. me as that may cause damage or paint peeling 4 English PARTS NAMES Camera mounting screw hole T CAUTION g d When installing the camera select a location that can support the total weight of the camera and accessories Electronic iris function switch El OFF El ON Sync switch INT L L INT Internal sync position L L Line lock position Q Line phase adjustment volume LINE PHASE Lens iris level volume LEVEL Q Lens iris output connector LENS This 4 pin connector is used to send the DC control signal and power supply to an auto iris type lens English 5 PARTS NAMES Flange back lock screw CS mount ring Lens mount cap The cap is installed to protect the lens mount section Remove the lens mount cap before installing a lens Video output connector VIDEO OUT BNC type Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector 24 V AC or 12 V DC input terminal 24 V AC 12 V DC GND See page 9 6 English MOUNTING THE LENS Please use a DC type auto iris lens sold separately Checking the lens mount Do not use lense with a length L more than 5 mm If not that may damage the camera and prevent proper installation 1 Remove the lens mount cap from the camera 2 Install the auto iris lens CS mount type lens C mount Carefully align the lens mount with the camera opening then turn the lens type lens slowly to install it
8. not drop the camera or subject it to strong shock or vibration E Install away from electric or magnetic fields If installed close to a TV radio transmitter magnet electric motor transformer audio speakers the magnetic field they generate will distort the image E Protect from humidity and dust To prevent damages to the camera do not install it where there is greasy smoke or steam where the dampness may get too high or where there is a lot of dust PRECAUTIONS E Protect from high temperatures Do not install close to stoves or other heat generating devices such as spotlights etc or where it could be subject to direct sunlight as that could cause deformation discoloration or other damages Be careful when installing close to the ceiling in a kitchen or boiler room as the temperature may raise to high levels Install where the temperature range will stay between 10 C and 50 C no condensation E Cleaning Dirt can be removed from the cabinet by wiping it with a soft cloth To remove stains wipe with a soft cloth moistened with a soft detergent solution and wrung dry then wipe dry with dry soft cloth Do not use benzine thinner or other chemical product on the cabinet as that may cause deformation and paint peeling Before using a chemical cloth make sure to read all accompanying instructions Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of ti
9. pc The C mount adaptor must be used to be able to install a C mount lens on the camera Lens iris plug L pn eee 1 pc 18 English SANYO Sanyo Electric Co Ltd 1AC6P1P2347 Printed in Japan L53V2 XE 0700KP DSP
10. prox 470 000 picture elements e Low smear anti blooming low lag no burning and no geometric distortion using he CCD solid state image device e 100 solid state components giving excellent immunity to shock and vibration e Not subject to interference from magnetic or electrostatic fields e High sensitivity minimum required illumination is 1 4 lux F1 2 e Horizontal resolution more than 480 TV lines Equipped with connectors for AC 24 V and DC 12 V power supply 2 English HSITDN3 PRECAUTIONS E In case of problem Do not use the camera if smoke or a strange odour comes from the unit or if it seems not to function correctly Disconnect the power cord immediately and consult your dealer or a Sanyo Authorized Service Centre E Do not open or modify Do not open the cabinet as it may be dangerous and cause damage to the unit For internal settings and repairs consult your dealer or a Sanyo Authorized Service Centre E Do not put objects inside the unit Make sure that no metal objects or flammable substance get inside the camera If used with a foreign object inside it could cause a fire short circuits or damages If water or a liquid gets inside the camera disconnect the power cord immediately and consult your dealer or a Sanyo Authorized Service Centre Be careful to protect the camera from rain sea water etc English 3 E Be careful when handling the unit To prevent damages do
11. volume on camera 1 If it still cannot be corrected please check that the polarity of the power cords of all connected devices is correct LINE A PHASE KREE Dro EH N a Monitor 12 English SETTINGS H Lens iris adjustment If using a DC type auto iris lens you will need to set the LEVEL volume when shooting in the conditions described below Counterclockwise To decrease the brightness Clockwise To increase the brightness e If shooting simultaneously in a dark room and through a bright window e If the subject background is extremely bright or dark e If the brightness of the picture on the monitor is not correct English 13 SETTINGS WEI Electronic iris function setting S Under normal conditions set the El switch to the El OFF position and use an auto iris lens However if you have a manual lens or fixed iris lens set the lens aperture to the shortest F stop and set the El switch to the El ON position If conditions are outside the electronic iris operation range or more than the maximum brightness it will cause saturation of the CCD In that case use a auto iris lens Note Please refer to the specifications for dynamic range of the electronic iris El OFF EI ON INT L L CAUTION e The electronic iris is suitable for normal indoor use When the El switch is set to the EI ON position
Download Pdf Manuals
Related Search