Primus Canada Car Speaker 160 User's Manual
Contents
1. above If only one loudspeaker is exhibiting the problem and you re confident that it s not caused by too little power too much power excessive equalization see solutions for Problems 1 and 2 WIRING DIAGRAM EXPLODED VIEW HIGH FREQUENCY TRANSDUCER i 85DA20AJ DT02 LOW FREQUENCY TRANSDUCER 16PR90BZQ FW01 CROSSOVER NETWORK 013 7500 00754 Primus 160 Cabinet Not for Sale ITEM ITEM NO DESCRIPTION QTY PART NO NO DESCRIPTION QTY PARTNO 1 Crossover Network 1 013 7500 00754 10 Faceplate Tweeter FE Screw T4 5 25 8 352 DM04525D597 2 Woofer 1 16PR90BZQ FW01 11 Terminal Cup Screw 3 5 L20 d 6mm 4 352 GM03520D850 3 Tweeter 1 85DA20AJ DT02 12 Network Screw t4 18 3 352 HM04018D497 4 ABS Plastic Trim Ring 196 5 144 8T 1 213 060 00492 13 Grille Cup 4 338 RUB 00114 5 Grille 337 204 3T Black 1 244 060 00259B 14 Rubber Footbase set of 4 1 373 000 00124 6 Port Tube 49 6 48 8 1 249 HIPS 00161 15 Outer Carton 1 400 000 04520 7 ABS Infinity Gold Logo 38 5 11 5 1 316 ABS 00532 2 16 Owner s Manual 1 406 000 01532 8 Network Cup W Binding Posts 1 317 ABS 00165 17 Polyfoam for Primus 160 2 431 000 02175 80 80mm ABS Gold Plating 440 350 80mm 9 Woofer Screw 4 L16 d 7mm 4 352 AM04016D834 18 Warranty Card 1 405 000 00312 Note A Phillips screwdriver and Torx bit screwdriver T20 size are required to service this product2. Primus 160 Infinity Loudspeaker Troubleshooting Repair Tips Most customers prefer to do simple loudspeaker repairs themselves By following the steps below a majority of loudspeakers can be returned to their original factory performance with minimum effort Choose the example that best describes the problem you are experiencing Problem 1 No sound or distorted sound from one loudspeaker in a pair or set Connect the dead distorting loudspeaker to a different amplifier channel one that had a functioning loudspeaker connected to it If it functions normally the problem is not loudspeaker related If the loudspeaker still makes no sound or sounds distorted a wire may have become loose or disconnected the network also known as a crossover may be defective the drivers woofer tweeter etc may be defective or in very rare cases all may be defective Refer to the wiring diagram and exploded view below The network is a small circuit board found on the inside of the terminal cup or mounted to an inside wall of the enclosure It sends low frequency sounds to the woofer high frequency sounds to the tweeter and if applicable mid frequency sounds to the midrange driver Make sure all wires are secure and connected Look for components on the network that look burnt bulged or abnormal If everything looks normal connect the network to the drivers from another matching loudspeaker MAKE SURE you attach the correct wires to each driver mid and
3. low frequency sounds can damage the tweeter If there is still no sound or distorted sound the network is defective If there is clean undistorted sound the drivers are defective Problem 2 No sound or distorted sound from one or more but not all drivers in an enclosure Remove the problem driver s from the enclosure and make sure all wires are secure and connected If they are proceed with the following test Woofer or midrange driver Connect the driver s and input terminals directly to the loudspeaker wires from your receiver amplifier and play some music at a reasonable volume If the driver now sounds normal produces a clean undistorted sound the network is most likely defective Tweeter Replace the tweeter with a functioning tweeter from another loudspeaker If the tweeter now functions normally produces clean undistorted sound the original tweeter is defective If the replacement tweeter also sounds distorted or produces no sound the network is most likely defective Problem 3 Loudspeakers distort rattle or pop at higher volumes This is usually NOT a loudspeaker problem Common causes are too much power playing the loudspeakers too loud and causing them to distort an amplifier with not enough power the amplifier can t produce the required volume without distorting excessive equalization turning the tone controls too far clockwise and or engaging the loudness bass boost button on your receiver or some combination of the
Download Pdf Manuals
Related Search