Philips TDA1510AQ User's Manual
Contents
1. DIMENSIONS mm are the original dimensions UNIT A A2 bp c D d Da 4 6 24 0 15 5 4 2 0 60 0 38 23 6 19 6 1o Note 1 Plastic or metal protrusions of 0 25 mm maximum per side are not included OUTLINE REFERENCES EUROPEAN VERSION JEDEC EIAJ PROJECTION SOT141 6 E40 oa ISSUE DATE January 1992 10 Philips Semiconductors 24 W BIL or 2 x 12 W stereo car radio power amplifier SOLDERING Introduction There is no soldering method that is ideal for all IC packages Wave soldering is often preferred when through hole and surface mounted components are mixed on one printed circuit board However wave soldering is not always suitable for surface mounted ICs or for printed circuits with high population densities In these situations reflow soldering is often used This text gives a very brief insight to a complex technology A more in depth account of soldering ICs can be found in our IC Package Databook order code 9398 652 90011 Soldering by dipping or by wave The maximum permissible temperature of the solder is 260 C solder at this temperature must not be in contact with the joint for more than 5 seconds The total contact time of successive solder waves must not exceed 5 seconds DEFINITIONS Data sheet status Objective specification Product specificati2. rms 0 2 mV Rg 102 Vh rms 0 35 0 8 mV Rg 10 kQ according to IEC 179 curve A Vn rms 0 25 E mV Supply voltage ripple rejection f 100 Hz note 5 SVRR 42 50 dB D C output offset voltage between AVs5 9 2 50 mV channels Power bandwidth 1 dB diot 0 5 B 30 to gt 40 k Hz January 1992 Philips Semiconductors 24 W BIL or 2 x 12 W stereo car radio power amplifier PARAMETER CONDITIONS SYMBOL Product specification TDA1510AQ Stereo application Output power with bootstrap Output power without bootstrap Frequency response Supply voltage ripple rejection Channel separation Closed loop voltage gain Noise output voltage r m s value January 1992 note 6 R 42 Vp 13 2V diot 0 5 diot 10 Vp 14 4 V diot 0 5 diot 10 R 2Q Vp 13 2 V diot 0 5 diot 10 Vp 14 4 V diot 0 5 diot 10 notes 6 8 and 9 R 40 Vp 14 4 V diot 10 notes 3 and 6 3 dB note 5 f 1 kHz Rg 10 kQ f 1 kHz note 7 f 20 Hz to 20 kHz Rg 02 Rg 10 kQ Rg 10 kQ according to IEC179 curve A 40 to gt 20k Philips Semiconductors Product specification 24 W BIL or 2 x 12 W stereo car radio B TDA1510AQ power amplifier Notes to the characteristics If V11 gt V4 then l4 must be lt 10 mA Closed loop voltage gain can be chosen between 32 and 56 dB BTL and is determined by external components Frequency response exte
3. information Where application information is given it is advisory and does not form part of the specification LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances devices or systems where malfunction of these products can reasonably be expected to result in personal injury Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale January 1992 11
4. INTEGRATED CIRCUITS DATA SHEET TDA1510AQ 24 W BTL or 2 x 12 W stereo car radio power amplifier Product specification January 1992 File under Integrated Circuits IC01 Philips PHILIPS Semiconductors DH LI p Philips Semiconductors Product specification 24 W BTL or 2 x 12 W stereo car radio power amplifier TDA1510AQ GENERAL DESCRIPTION The TDA1510AQ is a class B integrated output amplifier encapsulated in a 13 lead single in line SIL plastic power package Developed primarily for car radio application the device can also be used to drive low impedance loads down to 1 6 Q With a supply voltage Vp of 14 4 V an output power of 24 W can be delivered into a 4 Q Bridge Tied Load BTL or when used as a stereo amplifier 2 x 12 W into 2 Q or2x 7 W into 4 Q Features e Flexibility stereo as well as mono BTL e High output power e Low offset voltage at the output important for BTL e Large useable gain variation e Load dump protection e Good ripple rejection e A C short circuit safe to ground e Thermal protection e Low number small sized external components e Low stand by current possibility e Internal limiting of bandwidth for high frequencies e High reliability QUICK REFERENCE DATA PARAMETER CONDITIONS SYMBOL MIN TYP MAX UNIT Supply voltage range operating Vp 6 0 14 4 18 0 V non operating Vp 28 0 V non operating load dump protection Vp 45 0 V Repetitive peak output current lOR
5. M 4 0 A Total quiescent current lot 75 120 mA Stand by current lsb 2 mA Switch on current Iso 0 15 0 35 0 80 mA Input impedance pins 1 2 12 and 13 Z 1 MQ Storage temperature range Tstg 65 150 C Crystal temperature Te 150 C PACKAGE OUTLINE TDA1510AQ 13 lead SIL bent to DIL plastic power SOT 141C SOT141 6 1996 Aug 01 January 1992 2 Philips Semiconductors Product specification 24 W BTL or 2 x 12 W stereo car radio power amplifier TDA1510AQ LOAD bump SOAR THERMAL prot PROT SHUT DOWN 5 9 7286843 Fig 1 Functional diagram heavy lines indicate signal paths January 1992 3 Philips Semiconductors Product specification 24 W BTL or 2 x 12 W stereo car radio os TDA1510AQ power amplifier RATINGS Limiting values in accordance with the Absolute Maximum System IEC 134 PARAMETER CONDITIONS SYMBOL MIN MAX UNIT Supply voltage operating pin 10 Vp 18 V non operating Vp 28 V non operating load dump protection during 50 ms Vp 45 V Peak output current lom 7 6 A Total power dissipation see Fig 2 Prot Storage temperature range T stg 65 150 C Crystal temperature Te 150 C 20 7Z96815 1 Prot w WTE E Ee infinite ae eN E N te 7 FEJENET PERN 8 LN ERA RAGNE a Seal Co EE EN 20 40 60 80 100 120 140 160 Tamb C Fig 2 Power derating curves January 1992 4 Philips Semiconductors Product specificat
6. ion 24 W BIL or 2 x 12 W stereo car radio power amplifier TDA1510AQ HEATSINK DESIGN EXAMPLE The derating of the encapsulation requires the following external heatsink for sine wave drive Rih j mb 3 5 K W 24 W BTL 4 Q or 2 x 12 W stereo 2 Q maximum sine wave dissipation 12 W Tamb 65 C maximum 150 65 Rinna 4p 35 3 5 KW 2 x7 W stereo 4 Q maximum sine wave dissipation 6 W Tamp 65 C maximum _ 150 65 Rih h a 7 12 3 5 10 5 K W D C CHARACTERISTICS PARAMETER CONDITIONS SYMBOL Supply voltage range Vp Repetitive peak output current lorm Total quiescent current lot Stand by current lsb Switch on current V11 lt V10 note 1 lso January 1992 5 Philips Semiconductors Product specification 24 W BIL or 2 x 12 W stereo car radio a TDA1510AQ power amplifier A C CHARACTERISTICS Tamb 25 C Vp 14 4 V f 1 kHz unless otherwise specified PARAMETER CONDITIONS SYMBOL MIN TYP MAX UNIT Bridge Tied Load application BTL Output power with bootstrap note 6 R 42 Vp 13 2 V diot 0 5 Po 15 0 W diot 10 Po 20 0 WwW Vp 14 4 V diot 0 5 Po 15 5 18 0 W diot 10 Po 20 0 24 0 W Open loop voltage gain Go 75 dB Closed loop voltage gain note 2 Ge 39 5 40 0 40 5 dB Frequency response at 3 dB note 3 fr 20 to gt 20k Hz Input impedance note 4 Zil 1 MQ Noise output voltage r m s value f 20 Hz to 20 kHz Rg 02 Vh
7. on TDA1510AQ The device may be mounted up to the seating plane but the temperature of the plastic body must not exceed the specified maximum storage temperature T stg max If the printed circuit board has been pre heated forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit Repairing soldered joints Apply a low voltage soldering iron less than 24 V to the lead s of the package below the seating plane or not more than 2 mm above it If the temperature of the soldering iron bit is less than 300 C it may remain in contact for up to 10 seconds If the bit temperature is between 300 and 400 C contact may be up to 5 seconds This data sheet contains target or goal specifications for product development Preliminary specification Product specification This data sheet contains preliminary data supplementary data may be published later This data sheet contains final product specifications Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System IEC 134 Stress above one or more of the limiting values may cause permanent damage to the device These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied Exposure to limiting values for extended periods may affect device reliability Application
8. rnally fixed The input impedance in the test circuit Fig 3 is typ 100 kQ Supply voltage ripple rejection measured with a source impedance of 0 Q maximum ripple amplitude 2 V Output power is measured directly at the output pins of the IC Closed loop voltage gain can be chosen between 26 and 50 dB stereo and is determined by external components A resistor of 56 kQ between pins 3 and 7 is required for symmetrical clipping 60 5008 NO Ol Bs GO No Without bootstrap the 100 uF capacitor between pins 5 and 6 and the 100 uF capacitor between pins 8 and 9 can be omitted Pins 6 and 8 connected to pin 10 January 1992 8 Philips Semiconductors Product specification 24 W BIL or 2 x 12 W stereo car radio power amplifier TDA1510AQ APPLICATION INFORMATION 7Z89091 8 1 belongs to power supply 2kQ 4 7 pF Fig 3 Test and application circuit Bridge Tied Load BTL 7Z89092 4 1 belongs to power supply Fig 4 Test and application circuit stereo mode January 1992 9 Philips Semiconductors Product specification 24 W BIL or 2 x 12 W stereo car radio a TDA1510AQ power amplifier PACKAGE OUTLINE DBS13P plastic DIL bent SIL power package 13 leads lead length 12 mm SOT141 6 non concave I x view B mounting base side es A
Download Pdf Manuals
Related Search