Philips MML1801 User's Manual
Contents
1. 2 Press Enter button and Adjust or Adjust button to move the OSD image to RIGHT or to the LEFT 3 When the position is adjusted press the Enter button to return to OSD Position window 4 Select Exit and press again Enter button to return to OSD Settings OSD Vertical Position 1 Press Enter button when the Vertical Position is highlighted on OSD Position The Vertical Position bar appears OSD Position E Horizontal Position Vertical position Y Exit 2 Press Enter button and Adjust or Adjust button to move UP or DOWN the OSD image 3 When the position is adjusted press the Enter button to return to OSD Position window 4 Select Exit and press again Enter button to return to OSD Settings OSD Size 1 Press Enter button when the OSD Size is highlighted on OSD Settings The OSD Size window appears O Normal Double 2 Press the Adjust or Adjust button until the desired item is highlighted Normal Standard dimensions Double Double dimension 3 Press the Enter button to confirm your selection and return to OSD Settings window 24 6 5 5 6 5 6 6 6 0 OSD Transparency 1 Press Enter button when the OSD Transparency is highlighted on OSD Settings The OSD Transparency bar appears OSD Settings OSD Position W OSD Size OSD Transparency OSD Timeout Y Exit 2 Press Enter but2. The same as ABC full but with full scale of 350 cd m at 1000 lux 3 Press the Enter button to confirm your selection and return to Image Enhancement window Transfer Function 1 Press Enter button when the Transfer Functiopn is highlighted on Image Enhancement The Transfer Function window appears Transfer Function PMS Linear DICOM Monitor TG3 2 Press the Adjust or Adjust button until the desired item is highlighted Indicate the output curve relative to the input signal TG3 PMS Fixed output curve PMS like Linear The Tranfer Function is transparent DICOM The output curve follows the DICOM curve Monitor TG3 The output curve is the same as PMS standard monitor 3 Press the Enter button to confirm your selection and return to Image Enhancement window Advanced 1 Press Enter button when the Adavanced is highlighted on Main Menu The Advanced window appears 19 MML1801 gt lt Phase Adjust Clock Adjust OO Service Auto Setup Options Auto Phase Position Auto Clock Position Auto Level Restore Factory Presets Y Exit 2 Press the Menu or Menu button until the desired source is highlighted 6 3 8 Phase Adjust 1 Press Enter button when the Phase Adjust is highlighted on Advanced The Phase Adjust bar appears 2 Press Adjust or Adjust button to adjust the quality image Note Itis necessary to use video pattern dedicated to obtain the best resul
3. s video port see fig 11b f N fig 11b 11 MML1801 CONNECTING DIGITAL VIDEO DVD With the power the computer and the monitor turned off connect the supplied video cable from the monitor to the computer s video port see fig 12a fig 12a CONNECTING TOUCHSCREEN OPTIONAL If your monitor has this optional feature connect the monitor s RJ11 4 serial port to the computer s 9 pin RS 232 serial port using the proper cable see fig 12b fig 12b NOTE Follow the instructions included on the enclosed CD for installing the Touchscreen drivers on your system Following driver software installation calibrate your Touchscreen to the system following the procedure described on the enclosed CD 12 MML1801 INPUT INSTRUCTION O0000 00 Ld gl Y fig 13a AC INLET RS232 DVI INPUT VIDEO INPUT INPUT OUTPUT MAINS SOCKET or XVGA COMPOSITE TOUCHSCREEN AC INLET Meet IEC 320 CEE 22 STANDARD 110 220Vdc RS232 TOUCHSCREEN Connector RJ11 4 Pin 1 RS232 Rx Pin 2 RS232 Tx Pin 3 ENABLE Only with touch screen Pin 4 GND Note When the option touchscreen is used the RS232 monitor control is not available DVI INPUT Connector Microcross DVI D female connector Pinl D2 RX T M D S Pin 13 N C Pin2 D2 R
4. key will be pressed For every right key pressed a plus characters appears in dialog of Fig 26a KEYBOARD LOCK Fig 26a MML1801 26 INTENTIONALLY LEFT BLANK ATOOTA 607099 TTS INIA 3119 206 1404 1
5. B DSUB SOG When the calibration is OK it is necessary to execute the store operation to preserve the new values Press Enter button when the Store Video is highlighted 6 Select Exit and press again Enter button to return to Advanced or select Auto Setup Options Service gt Video Offset Video Gain Store Video Exit 6 3 11 Auto Setup Options 1 Press Enter button when the Auto Setup Options is highlighted on Advanced The Auto Setup Options window appears 2 Press Menu or Menu button to select automatic options Auto Setup Options and Auto Clock feature define the modality of Auto Adjust of the video image when the video timing is recognized 3 Select Exit and press again Enter button to return to Advanced or select Auto Level Auto Setup Options gt Auto Setup On Modeset Auto Clock Feature Y Exit 6 3 12 Auto Setup On Modest 1 Press Enter button when the Auto Setup On Modest is highlighted on Auto Setup Options The Auto Setup On Modest window appears 2 Press Adjust or Adjust button until the desired item is highlighted 3 Press the Enter button to confirm your selection and return to Auto Setup Options window 21 MML1801 MML1801 6 3 13 6 3 14 6 3 15 6 3 16 Auto Setup On Modest e Enabled Disabled Only Once Enabled Every time the video timing changes Disabled Never Only Once Only the first time that the video timing is recognized A
6. MML1801 14 OSD ON SCREEN DISPLAY MENU STRUCTURE MAIN MENU INFORMATION CODE VERSION EXIT IMAGE ADJUST HORIZONTAL POSITION VERTICAL POSITION SCALE CENTER FULL SCREEN MAINTAIN ASPECT RATIO ENTER IMAGE ENHANCEMENT ABC SELECTION OFF REDUCED FULL TRANSFER FUNCTION TG3 PMS LINEAR DICOM MONITOR TG3 EXIT ADVANCED PHASE ADJUST LOCK ADJUST SERVICE VIDEO OFFSET VIDEO GAIN STORE VIDEO EXIT AUTO SETUP OPTIONS AUTO SETUP ON MODESET ENABLED DISABLED NLY ONCE AUTO CLOCK FEATURE HA DISABLED EXIT AUTO PHASE POSITION AUTO CLOCK POSITION AUTO LEVEL RESTORE FACTORY PRESETS EXIT EXIT LANGUAGES ENGLISH FRANCAIS DEUTSCH ESPANOL ITALIANO OSD SETTING OSD POSITION HORIZONTAL POSITION VERTICAL POSITION EXIT OSD SIZE NORMAL DOUBLE OSD TRANSPARENCY OSD TIMEOUT 10 Sec 20 Sec 30 Sec 45 Sec 60 Sec 90 Sec 120 Sec DISABLED EXIT VIDEO SOURCE BNC DVI DSUB HT AND VT SYNC DSUB SOG GREEN INPUT EXIT KEYBOARD OPTION KEYBOARD UNLOCK KEYBOARD LOCK EXIT MML1801 e Function Key Enter gt Adjust Menu Adjust Menu OSD KEY FUNCTIONS Description It activates the OSD MAIN MENU if this is not active otherwise selects and executes a desired OSD Special Function When main menu or sub menu is active it allows to move or scroll to the previous upper item or decrement the magnitude of the parameter When main menu or sub
7. MML1801 FAMILY LCD 18 MONOCHROME MONITOR Users Manual Copyright 2002 FIMI S r l Saronno Italy All rights are reserved Reproduction in whole or in part is prohibited without the written consent ofthe copyright owner Printed in Italy Rev 1 1 Copyright This manual is copyrighted with all rights reserved Under the copy rights law this manual may not be copied in whole or part without written consent of Philips Under the law copying includes translating into another language or format The monitor described in this manual has been certified registered by the safety agencies regulatory authori ties as model n FCC Notice This equipment has been tested and found to comply with the limits for a class A digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This monitor complies with the European community radio interference standard EN 55011 Class B Modification The FCC requires the user to be notified that any changes or modifications made to this device t
8. NTING INSTRUCTION sccssssscsssssensessoasccsssseresessensnsesnse 8 CONNECTING INSTRUCTION ccssscccsscsscosorssesseseossensecses 9 connecting AC sessions 1 0 connecting analog VIdeo uie trea pest connecting composite video un 11 connecting digital idea 12 connecting the optional touchscreen 12 INPUT INSTRUCTION seen 13 CONTROL PANEL DESCRIPTION ee eeeeee eene 14 OSD ON SCREEN 15 DOCU SERO A A 15 OSD key TIBOLIOBIB aeg 16 OSD COMO Se O 16 o Li MN E 16 A 17 A 17 horizontal POSO iia 18 POSO sario 18 scale Cain 18 image 4 18 ABC SCC COT Sei irpo edo esi piss 18 transfer Function uses 19 CUM rero A 19 phase ad ebe teneor eaae 20 clock adjust nenne 20 IARE EAE AN ES 21 auto setup 21 auto setup on 24 auto tlock Sedibus iaa 22 22 auto ClockPositio ereccion 22 uoc ernannte 22 restore factory PTOS Lucinda 23 A A 23 OSD setting anne 23 24 OSD vertical position 24 p p 23 A ei 23 OS DCO tere 23 VideO ROUTE 25 keyboard OpEHODL seri antracita 26 MML1801 4 TECHNICAL INF
9. ORMATION Display Panel Supported Grayscale Dimensions Weight Active display area Response Time Viewing Angle Contrast Ratio White luminance Pixel Pitch Video interface Scanning Frequency Power Consumption Power Supply Operation Temperature Storage Temperature Humidity Shock 18 1 460mm SXGA active matrix monochrome TFT LCD 8 bit Panel 410 x 362 x 105 mm width x height x depth 7 7 Kg panel 3 7 Kg pedestal 359 0 x 287 2 mm width x height 40 mS 10 to 90 rising 90 to 10 falling 85 typ horizontal or vertical contrast ratio gt 15 550 1 typ 500 cd m 0 2805 one triad x 0 2805 mm width x height Analog Input BNC connection for Composite Video Signal DSUB 15 connection for Separate Sync Video Signal or SOG Video Signal DVI D connection for TMDS signal link standard version BNC connection for Loop Through Composite Video Signal Digital Input Analog Output Max pixel clock 135MHz lt 70 W From 90 to 264 Vac 50 60 Hz 10 to 45 C 20 to 60 C 80 Maximum Wet Bulb should be 39 C and No condensation Half sine wave 50G 11msec X Y Z total 6 Directions Each two time shock 5 MML1801 DIMENSIONS MML1801 6 DIMENSIONS 7 MML1801 INSTALLATION Before unpacking the monitor prepare a suitable workspace You need a stable and level surface near a grounded wall outlet in an area that is relative
10. X T M D S Pin 14 5 Power Pin 3 GND Data 2 shield Pin 15 GND Pin4 N C Pin 16 Hot Plug Detect Pin5 N C Pin 17 DO_RX T M D S Pin6 SCL For DDC Pin 18 DO RX T M D S Pin 7 SDA For DDC Pin 19 GND Data 0 shield Pin8 N C Pin 20 N C Pin9 DI RX T M D S Pin 21 N C Pin 10 DI RX M D S Pin 22 GND Clock shield Pin 11 GND Data 1 shield Pin 23 T M D S Pin 12 Pin24 RX T M D S VIDEO INPUT XVGA Connection DSUB15 female connector Pin 1 R in Pin9 N C Pin 2 G in Pin 10 GND Pin 3 B in Pin 11 N C Pin 4 N C Pin 12 SDA For DDC option Pin 5 N C Pin 13 H S in Pin 6 GND Pin 14 V S in Pin 7 GND Pin 15 SCL For DDC option Pin 8 GND COMPOSITE INPUT Connection BNC 75Q male coaxial jack Body Signal GND Center contact Composite Video input COMPOSITE OUTPUT Connection BNC 75Q male coaxial jack Body Signal GND Center contact Composite Video output 13 MML1801 CONTROL PANEL DESCRIPTION On the front bottom side part of the unit the following controls are placed BRIGHTNESS ADJ BRIGHTNESS ADJ MENU SELECT BRIGHTNESS Recall to 500 Cd m MENU SELECT ENTER Store Source Select Light sensor LED GREEN 500 cd m Power on RED lt 500 cd m ORANGE Stand by fig 14a Power Switch Brightness S E Adjust V p Brightness Adjust Menu select Menu select
11. about 5 sec check Input Signa XXX XXX Current Video Source BNC DVLDSUB SOG After about 5 sec the monitor will go in Stand By mode The led colour will become orange To change the Video Source when the Video Source is not available to follow the followings steps Wait the Warning Message Press contemporarily the brightness keys When the Warning message disappears Release the brightness keys Execute the normal change of the Video Source see ref 6 6 0 6 7 0 Keyboard Option 1 Press Enter button when the Keyboard Option is highlight on Main Menu The Keyboard Option bar appears Keyboard Option Keyboard Unlock Keyboard Lock 2 Press the Adjust or Adjust button until the desired item is highlighted 3 Press the Enter button to confirm your selection and return to Main Menu window REMARK To select the Keyboard status LOCK or UNLOCK use the Keyboard Option Menu The new status is stored in E2prom the default status is UNLOCK If the Keyboard Status is UNLOCK any key and any OSD function is available If the Keyboard Status is LOCK Brightness Brightness and Reference Setting Recall 500 Cd m are always available Pressing OSD key will appear the dialog of Fig 26a The OSD menu will appear after having performed the follow correct keys sequence Brightness Brightness Brightness Menu The dialog Fig 26a will disappear any time a wrong
12. hat are not expressly approved by the manufacturer may vold the user s autority to operate the equipment Cables Connections to this device must be made with shielded signals cables with metallic RFI EMI connector hoods to maintain compliace with FCC Rules and Regulations The lighting flash with arrowhead simbol is intend to alert the user of the presence of uninsulated dangerous voltage within the product s enclosure that may be sufficient magnitude to constitute a risk of electrical shock to people N exclamation mark is intended to alert the user of the presence of important operating and maintenance servicing instructions in literature accompanying the appliance CAUTION RISK OF ELECTRICAL SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR SHOCK AZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR EXCESSIVE MOISTURE THE ENCLOSURE HAS TO BE CHECKED UPON COLLISION DAMAGE REFER TO QUALIFIED SERVICE PERSONNEL MML1801 p INTRODUCTION FIMI Medical Grade MML1801 Medical is a monochrome active matrix liquid crystal display exclusively designed for medical imaging applications The monitor can be used for X ray and PACS and other medical systems requiring a very high level of
13. image quality for examination and control purpose and can accept an analogue signal input as well as a digital input The product is engineered to meet all stringent medical safety requirements including UL2601 1 CAN CSA C22 2 No 601 1 EN 60601 1 and the product can be safely placed next to other sensitive equipment with no risk of harmful interference Certifications of monitor also cover requirements for liquid ingress and current leakage from power supply The typical application is to display high resolution X ray images This product delivers much higher brightness than the standard Flat Panel monitors equal at least to the brightness level of current high end monochrome CRT monitors used for the same applications The other key features of the MML1801 are long term luminance stability through backlight stabilization circuit luminace stability vs the viewing angle contrast stability vs the viewing angle brightness uniformity automatic brightness control with backlight sensor and ambient light sensor internal automatic greyscale calibration 10 bit L U T The tilt swivel base can be removed and the monitor uses a mounting plate that conforms to the VESA mounting standard that allows flexible mounting options including wall mounting and rolling stands 3 MML1801 CONTENTS TECHNICAL INFORMATION ssssosssssessessersorssnssnnennsensenee 5 DIMENSIONS 6 INSTALLATION uses 8 MOU
14. lect Exit and press Enter button to return to Image Adjust Languages 1 Press Enter button when the Languages is highlighted on Main Menu The Languages window appears The ON SCREEN DISPLAY shows the five languages available The default is English but you can select Frangais Deustch Espanol or Italiano 2 Press the Adjust or Adjust button until the desired item is highlighted 3 Press the Enter button to confirm your selection and return to Main Menu window English Francais Deustch Espafiol Italiano 6 5 0 OSD Settings 1 Press Enter button when the OSD Settings is highlighted on Main Menu The OSD Settings window appears 2 Press the Menu or Menu button until the desired item is highlighted OSD Settings OSD Position OSD Size L OSD Transparency OSD Timeout Y Exit 6 5 1 OSD Position 1 Press Enter button when the OSD Position is highlighted on OSD Settings The OSD Positions window appears 2 Press the Menu or Menu button until the desired item is highlighted OSD Position E Horizontal Position Vertical position Y Exit 23 MML1801 MML1801 6 5 2 6 5 3 6 5 4 OSD Horizontal Position 1 Press Enter button when the Horizontal Position is highlighted on OSD Position The Horizontal Position bar appears OSD Position E Horizontal Position Vertical position Exit
15. ly free of glare from sunlight or other sources of bright light The monitor is cooled by two internal fans For best performance do not block the cooling vents NOTE before istalling this monitor please refer to the user s guides of your computer and video adapter to make sure if these equipments require any change of setting Positioninig WARNING WHEN POSITIONING THIS EQUIPMENT ENSURE THAT THE MAINS PLUG AND SOCKET ARE EASILY ACCESSIBLE While unpacking the monitor inspect it and other package contents for shipping damage that could cause a fire or shock hazard immediately report any shipping damage to the carrier or transportation company and contact customer service for assistance keep all packing material in case you need to ship store or return the monitor After unpacking the monitor make sure the following items are included e Monitor e Mains cord set 1 8 meter USA version e Mains cord set 1 8 meter EU version e Signal cable 1 8 meter DB15 DB15 e This user s manual If you ordered the monitor with the resistive touchscreen option the following items should also be included e User s manual of touchscreen e Touchscreen cable PEDESTAL standard With the built in pedestal you can tilt the monitor for a most comfortable viewing angle as shown in figure 8a 5 15 g 8a MML1801 8 MOUNTING INSTRUCTION PEDESTAL STANDARD OPTIONAL The pedestal must be fixed at m
16. menu is active it allows to move or scroll to the previous down item or increment the magnitude of the parameter Pressing Enter key the MAIN MENU highlight selection is the first Sub menu item Information Pressing Menu or Menu key the highlight selection of menu item moves downward upward g y ghlig p Pressing Enter key the current menu window disappears and is replaced by the new sub menu windows 6 0 0 OSD ON SCREEN DISPLAY CONTROLS 6 1 0 Main manu After the activation of OSD Main Menu appears the following window Information Image Adjust Languages OSD Settings Video Source gt Keyboard Option MML1801 Exit Information 4 Image Adjust Languages OSD Settings PHILIPS OO Video Source gt Keyboard Option n Exit 1024 x 768 8 60 Hz DSUB It shows the hardware and firmware status operating hours and release number To adjust the picture when it is not correct To select the correct language To adjust the OSD options position attribute activity delay To select the correct video input source To select the keyboard status To exit from MAIN MENU 16 6 2 0 Information 1 Press Enter button when the Information is highlighted on Main menu The Information window appears MML1821 Model Ver CO 62 DO 62 Firmware Release h00002 Operating Hours Video timing number 3 To press Enter buttton to return to Main Me
17. nu FIMI Philips MML1801 Ver CO 62 DO 62 h00002 c1B gt Y Exit 6 3 0 Image Adjust 1 Press Enter button when the Image Adjust is highlighted on Main Menu The Image Adjust window appears Image Adjust gt 0 Horizontal Position Vertical position Scale Center D Image Enhancement Advanced Y Exit 6 3 1 Horizontal Position 1 Press Enter button when the Horizontal Position is highlighted on Image Adjust The Horizontal Position bar appears Image Adjust E Horizontal Position Vertical position W Scale Center D Image Enhancement Advanced Y Exit 2 Press Adjust or Adjust button to move the image to the left or right 3 When the position is adjusted press the Enter button to return to Image Adjust window 4 To select Exit and press again Enter button to return to Main Menu or select Vertical Position 17 MML1801 6 3 2 Vertical Position 1 Press Enter button when the Vertical Position is highlighted on Image Adjust The Vertical Position bar appears Image Adjust E Horizontal Position Vertical position W Scale Center Image Enhancement Advanced Y Exit 2 Press Adjust or Adjust button to move the image to the up or down 3 When the position is adjusted press the Enter button to return to Image Adjust window 4 To select Exit and press again Enter button to
18. onitor with N 6 screws M3x10 included into the BOX as shown in figure 9a ARM VESA PLATE fig 9b y WP An arm with VESA 100x100 interface must be fixed at monitor with N 4 screws M4x10 as shown in figure 9b 9 MML1801 CONNECTING INSTRUCTION CONNECTING AC POWER Plug the receptacle and of the cord set into the AC power adapter then plug the power connector of the adapter into the power port on the monitor This power port is located on the back of the monitor see fig 10a MAINS SWITCH Insert the plug end of the power cord into a grounded wall outlet For added protection use a surge protector between the AC adapter and the electrical wall outlet to prevent sudden current variations from reaching the monitor MML1801 10 CONNECTING ANALOG VIDEO 5 With the power the computer and the monitor turned off connect the supplied video cable from the monitor to the computer s video port see fig 11a fig lla Make sure the video cable connector is securely connected to the video port on your computer Turn the monitor on first and then turn on the computer CONNECTING COMPOSITE VIDEO BNC With the power the computer and the monitor turned off connect the supplied video cable from the monitor to the computer
19. return to Main Menu or select Scale Center 6 3 3 Scale Center 1 Press Enter button when the Scale Center is highlighted on Image Adjust The Scale Center window appears Scale Center 9 Full Screen Maintain Aspect Ratio Center The ON SCREEN DISPLAY shows the three modes available The default is Full Screen but you can select Maintain Aspect Ratio or Center 2 Press the Adjust or Adjust button to change the video mode the choosen mode is highlighted 3 Press the Enter button to confirm your selection and return to Image Adjust window 6 3 4 Image Enhancement 1 Press Enter button when the Image Enhancement is highlighted on Image Adjust The Image Enhancement window appears Image Enhancement gt i ABC selection Transfer Function NY Exit 2 Press the Menu or Menu button until the desired item is highlighted MML1801 18 6 3 5 ABC Selection 6 3 6 6 3 7 1 Press Enter button when the ABC Selection is highlighted on Image Enhancement The ABC Selection window appears ABC Selection ABC Off ABC Reduced ABC Full 2 Press the Adjust or Adjust button until the desired item is highlighted ABC off Manual back light control regulated by panel button from 250 cd m to 500 cd m ABC full Automatic control of back light the back light is function of ambient light and follow a semilogaritmic courve from 200 cd m at 1 lux to 500 cd m at 1000 lux ABC reduced
20. t 3 When the position is adjusted press the Enter button to return to Advanced window 4 Select Exit and press again Enter button to return to Image Adjust or select Clock Adjust lt Phase Adjust Clock Adjust 00 5 1 Auto Setup Options Auto Phase Position Auto Clock Position Auto Level Restore Factory Presets Y Exit 6 3 9 Clock Adjust 1 Press Enter button when the Clock Adjust is highlighted on Advanced The Clock Adjust bar appears 2 Press Adjust or Adjust button to adjust the quality image Note It is necessary to use video pattern dedicated to obtain the best result 3 When the position is adjusted press the Enter buton to return to Advanced window 4 To select Exit and press again Enter button to return to Image Adjust or select Service Phase Adjust gt Clock Adjust OO Service Auto Setup Options Auto Phase Position Auto Clock Position Auto Level l Restore Factory Presets Y Exit MML1801 6 3 10 Service 1 Press Enter button when the Service is highlighted on Advanced The Service window appears 2 Press Menu or Menu button until the desired item is highlighted and press Enter 3 Press Adjust or Adjust button to adjust the quality image 4 When the item is adjusted press the Enter button to return to Service window 5 Video Offset and Video Gain are items to use to calibrate the video signal BNC DSU
21. ton and Adjust or Adjust button to choose the degree of transparency of the OSD image 3 When the position is adjusted press the Enter button to return to OSD Settings window 4 Select Exit and press again Enter button to return to OSD Main Menu OSD Timeout 1 Press Enter button when the OSD Timeout is highlight on OSD Settings The OSD Timeout bar appears OSD Timeout eo 10 Sec 20 Sec 30 Sec 45 Sec 60 Sec 90 Sec 120 Sec Disabled 2 Press Enter button and Adjust or Adjust button to choose the time of activation of the OSD Menu 3 Press the Enter button to confirm your selection and return to OSD Settings window Video Source The ON SCREEN DISPLAY shows the four sources available The default is BNC Composite Video with Sync On Green but you can select DVI Digital Video Input DSUB D sub input Video with separated syncr DSUB SOG D sub input Video with Syncr On Green 1 Press Enter button when the Video Source is highlighted on Main menu The Video Source window appears 2 Press the Adjust or Adjust button until the desired source is highlighted 3 Press the Enter button to confirm your selection and exit from OSD Main Menu gt OO BNC OODVI OODSUB Ht and Vt Sync OODSUB SOG Green Input OODSUB Ht Vt Sync IP Exit see next page MMLI801 25 Video Source If the Video Signal is not available a warning message will appear on the screen for
22. uto Clock Feature 1 Press Enter button when the Auto Clock Feature is highlighted on Auto Setup Options The Auto Clock Feature window appears 2 Press Adjust or Adjust button until the desired item is highlighted 3 Press the Enter button to confirm your selection and return to Auto Setup Options window Auto Clock Feature Enabled Disabled Enabled Every time the video timing changes Disabled Never Auto Phase Position 1 Press Enter button when the Auto Phase Position is highlighted on Advanced To perform an automatic adjustmant of the video image Valid only BNC DSUB SOG and DSUB video source 2 Select Exit and press again Enter button to return to Image Adjust or select Auto Clock Position Auto Clock Position 1 Press Enter button when the Auto Clock Position is highlighted on Advanced To perform an automatic adjustmant of the video image Valid only BNC DSUB SOG and DSUB video source 2 Select Exit and press again Enter button to return to Image Adjust or select Auto Level Auto Level 1 Press Enter button when the Auto Level is highlighted on Advanced To perform an automatic calibration of the video signal Valid only BNC DSUB SOG and DSUB video source 2 Select Exit and press again Enter button to return to Image Adjust 22 6 3 17 Restore Factory Preset 6 4 0 1 Press Enter button when the Restore Factory Preset is highlighted on Advanced To reload factory settings 2 Se
Download Pdf Manuals
Related Search