Home

Philips 32PFL3509/F7 User's Manual

1. Vat HDMI cable HDMI DVI Connection This Unit can be connected to your PC that has a DVI Terminal Use an HDMI DVI Conversion Cable for this Video Digital Connection and it requires Stereo mini 3 5mm Plug Audio Cable for Analog Audio signal as well Stereo mini 3 5 mm plug IN Audio cable OUT Vs ae N HDMI DVI OUT PC conversion cable VGA Connection This unit is equipped with a PC Input jack If you connect this Unit to your PC you can use this Unit as a PC monitor Use a VGA cable for this Video Connection and it requires a Stereo mini 3 5mm Plug Audio Cable for Analog Audio signal as well Stereo mini 3 5 mm plug 2 IN Audio cable OUT i VGA cabl T AN N OUT PC The following Video signals can be displayed VGA 640 x 480 SVGA 800 x 600 XGA 1 024 x 768 WXGA 1 280 x 768 1 360 x 768 Other formats or non standard signals will not be displayed correctly 14 Note s e Please purchase the VGA cable or HDMI DVI Conversion Cable that has a ferrite core The following operations may reduce noise Attach a ferrite core to the AC Power Cord of your PC Unplug the AC Power Cord and use the built in battery of your Portable Laptop PC e Use an HDMI cable with the HDMI logo a certified HDMI cable High Speed HDMI cable is recommended for the Better c
2. Normal Noise reduction Black stretch Dynamic contrast Gamma to set the picture color temperature to Personal Cool Normal or Warm ings Personal picture will be set omatically lt Cursor Cursor gt gt F Decrease Red o Increase Red Red gain Contrast Contrast o G o Decrease o Increase Green reen gain Green Contrast Contrast o Decrease Blue to Increase Blue Blue gain Contrast Contrast o Red offset gt Brightness Green o offset Green Brightness ncrease Red Brightness Decrease Red Decrease o Increase Green Brightness o Decrease Blue to Increase Blue Blue offset Brightness Brightness t o Set Noise reduction on Ree Nebsinan mage on fio rane Back Calor o Off o Set Dynamic contrast to Off o Enhance Contrast in an Image Automatically o Change the Gamma setting changes the Brightness and Contrast in the picture 23 English Sound You can select Audio Output through a Digital Audio Output connector to Output Audio in its native Digital output Bitstream format as Bitstream to connected format Audio receiver You must set Home in Location p 31 PCM to Output PCM format Otherwise personalized Picture and Sound settings will not be memorized after the Unit goes into Standby Mode You can set the Output mode as a default for the Sound mode Analog TV only Before you begin 1 Press P and
3. The channel display forthe removed channel darkens You will not be able to select the channel again using CH To reactivate a removed channel use A W and press OK The registered channels are highlighted When you remove a main channel its subchannels are removed as well Note s The channel with DTV indicated on the display is ATSC Otherwise the channel is Analog TV NTSC Continued on next page Add channels This function lets you add the off the air Analog TV or Analog Cable channels that were not added by the Autoprogram due to reception conditions during the Initial Setting 1 Use A Y to select Add channels then press OK 2 Use the NUMBER keys to enter the number of the channel you want to add then press OK For analog channels select a channel to be added using number keys For digital channels Autoprogram function is required BACK H Ch Change Q Back Note s e If Setup completes successfully Added to the channel list is displayed If External Input is used it is not possible to register the channel and Unavailable will be displayed on the TV screen Some channels cannot be selected by CH Use the NUMBER keys to select the non memorized channels Antenna Confirmation This function lets you check the Digital signal strength of each channel 1 Use A Y to select Antenna then press OK 2 Use the NUMBER keys or CH to select the cha
4. Features DTV Analog TV CATV You can use your Remote Control to select channels which are Broadcast in Digital format and conventional Analog format Also Cable and Satellite subscribers can access their TV channels Information display You can display the Title contents DTV only and other information of the current program on the TV screen Autoprogram This Unit Automatically scans and memorizes channels available in your area Eliminating difficult Setup procedures Child lock This feature allows you to Block children s access to inappropriate programs e Closed Caption decoder Built in Closed Caption decoder displays text for Closed Caption supported programs MTS SAP tuner Audio can be selected from the Remote Control Auto Standby If there is no Input Signal and no operation for 15 minutes the Unit will go into Standby mode Automatically Sleep Timer You can set the Unit to go into Standby mode after a specific amount of time Choices for On screen language Select your On screen language English Spanish or French e Stereo sound function PLL frequency synthesized tuning Provides free and easy channel selection and lets you tune directly to any channel using the number and decimal point keys on the Remote Control Various adjustments for Picture and Sound Customizes image quality suitable for your room and sets your sound preference e EasyLink via HDMI link EasyLink allo
5. Note s e The Unit accepts 480i 480p 720p and 1080i of Video signals for this Connection Composite Analog Video Connection Composite Analog Video Connection offers standard Picture quality for Video Devices connected to the Unit If you connect to the Unit s Component Composite Video Y VIDEO Input jack green connect Audio Cables to the Audio L R Input jacks When the Audio is monaural then only connect to the Audio L Input jack IN OUT En Audio L R ES Video cables DVD player Note s e With this Unit yellow cable must be connected to Y green jack on the Component Video Input jacks e Whenever you connect to the Composite Video Input jack Y VIDEO you must disconnect the Component Video Input jacks Pb and Pr If you leave those jacks connected it may cause of an unstable picture Digital Audio Output Connection Ifyou connect this Unit to an External Digital Audio Device you can enjoy multi channel Audio like 5 1ch Digital Broadcasting sound Use a Digital Audio Coaxial Cable to connect the Unit to Extemal Digital Audio Devices oel IN 212 O mua i Digital home theater OUT Digital Audio coaxial cable amplifier Continued on next page PC Connection HDMI Connection This Unit can be connected to your PC that has an HDMI terminal Use an HDMI cable for this Digital Connection IN OUT
6. SOURCE Repeatedly to select the Set top Box or the Connected Device and wait a few seconds till the Picture appears Pressing reverses the direction of the Input modes e g 11 1 BR gt A gt BL DTV Analog TV channel B Video aoe 2 Use the Remote Control for the Set top Box or the Connected Device to select Channels to view 18 English Sleep Timer Sleep Timer can set the Unit to go into Standby mode after an incremental period of time 0225555 CC steep 9 sap CEE Press SLEEP Repeatedly to change the amount of time 3 Sleep timer 120 min increases the time by 30 minutes up to 120 minutes Press SLEEP Once to call up the display for checking the remaining time e To cancel Sleep Timer press SLEEP Repeatedly until Off is displayed Switching Audio Mode 15 2 ce SLEEP 0 sap 0 CCE Digital TV Operation 1 Press SAPto display the currently selected Language 41 1 and the number of available Languages WEA 2 Press SAP Repeatedly to cycle through the available Audio Languages Note s Available Languages differ depending on the Broadcast Other is displayed when the Audio Language cannot be acquired or the acquired Languages are other than English French or Spanish Press SAP to display the currently selected Audio mode While receiving an MTS broadcast press SAP Repeatedly 11 to cycle through the available Audio Channels SAP STEREO e g When All Audio
7. Press amp on the Remote Control to mute the sound Press 6x again or VOL to recover the original sound 17 English Switching Channels SOURCE 6 o PREV CH e sono oooooocood To select Channels by using CHW A or CH Press CH Y Down A Up on the Front panel or press CH on the Remote Control or the Side panel To select Channels by using the NUMBER keys Digital TV Operation For Digital channels press a number followed by a dot e and the corresponding sub channel number When selecting Digital channel 11 1 Be sure to press before entering the subchannel number Gp as a an O CA When selecting Cable or Analog channel 11 an an Press PREV CH to retum to the previously viewed channel Note s To select the non memorized channels use the NUMBER keys No signal will appear on the TV screen after the subchannel broadcast is over Audio only program message will appear on the TV screen when you receive only a sound signal Watching Channels from an External Device Switching Each Input Mode can easily switch with the Remote Control between TV DTV or Analog TV and External Devices when they are connected to the Unit 1 TurnOna Set top Box or the Connected Device The picture from the Set top Box or the Connected Device might appear Automatically on the TV screen If the picture does not appear Press
8. make sure you select the correct Source by using SOURCE key on TV or SOURCE key on Remote Control JA FJ RF cable ai HDMI cable Set top Box 11 English If connecting a Set top Box through Component Video Input If the TV is connected to a cable satellite set top box via Component Video Input make sure you select the correct Component Video Source by using J SOURCE JA RF cable Audio L R cables hd IN ZAS Component Y Pb Pr E aa OUT Set top box 05 IN 5 video cables Connecting a Cable Satellite IPTV Box Blu ray Disc DVD Recorder via Composite Connectors and Analog Audio Do Not place your Recorder too close to the Screen because some Recorders can be susceptible to Signals from the TV OUT Cable RF cable IN Set top Box OUT CE pes 000 oH EE RF cable OUT Audio L R Video cables IN T LD e Audio L R ber YAA 2 Video cables Blu ray Disc DVD Recorder Note s f you have any question about the DTV s Antenna visit www antennaweb org for further information Depending on your Antenna system you may need different types of combiners mixers or separators splitters for HDTV Signal The minimum RF bandpass on these Devices is 2 000MHz or 2GHz For your safety and to avoid damage to this Unit please unplug the RF Coaxial Cable from
9. Signal Three types of Display Modes can be Selected for a PC Input Signal Press FORMAT Repeatedly to Switch the TV Aspect Ratio For 16 9 Video signal gt Normal W Movie expand Full can also be selected after Wide if an HDMI Device is selected This picture format similarly displays like Normal Full Wide HDMI Device only Zoom 19 Normal Original size Shortened horizontally 4 za Sidebars appear on both edges of the screen Vertically stretched to fill the screen This only crops out the top of the picture Zo m Maximum size without changing its horizontal and vertical ratio Wide Horizontally stretched picture This crops out the left and right sides of the picture Movie expand picture format similarly displays like 16 9 Full Wide HDMI Device only For 4 3 Video signal Normal K 16 9 xy Movie expand Full can also be selected after Wide if an HDMI Device is selected This de Zoom Original size Sidebars appear on both edges of the screen Normal Stretched horizontally to fill the screen Movi Stretched more vertically at the top of the screen ovie expand his crops out the top of the picture Maximum size that is more vertically stretched to fill Zoom the screen This crops out the top and bottom of the picture Wide Original size and the edges stretched horizontally to fill the screen For PC Input signal L J Norma
10. Your connected EasyLink device off stays On even if the Unit goes into Standby mode Auto device off Your connected EasyLink device Turns Off Automatically when the Unit goes into Standby mode This Unit will Turn On when the Power On Signal is sent from your connected EasyLink device This Unit stays in Standby mode off even if you Turn On your Auto TV on connected EasyLink device This Unit Turns On Automatically when you Turn On your connected EasyLink device You can operate some functions such as Disc Playback or call up the menu of the connected devices by using this Unit s Remote Control Disables the device control PLAY gt gt STOP E FWD b gt REV lt q SKIP gt P SKIP Ha PAUSE II LINK AVA Device control OK BACK the NUMBER buttons RED GREEN BLUE YELLOW can be used to control your connected fun Link devices by this unit s remote control 30 English Device list This function lets you see the product model number or name of Connected Devices Use A Y to select the desired EasyLink devices listed on the TV screen then press OK Your connected EasyLink device will be Turned On if the device is in Standby mode HDMI1 DVD recorder HDMI2 Features INFO BACK cx AO Refresh Back Setting your Location to Home You can set the Location of your TV to Home or Retail Choosing Home gives you full flexibility to change predefined sett
11. the Antenna Input jack before moving the Unit f you did use an Antenna to receive Analog TV it should also work for DTV reception Outdoor or attic Antennas will be more effective than a Set top Box or inside Antenna To Turn On your reception source easily between Antenna and Cable Install an Antenna selector f you are not receiving a Signal from your Cable service contact the Cable provider Plugging in the AC Power Cord Make sure All the Necessary Connections are made before the AC Power Cord is plugged into an AC outlet E Caution Do Not connect the AC Power Cord to an AC Power Supply outside the indicated voltage of this Unit 120V AC e Connecting the AC Power Cord to a Power Supply outside of this range may result in Unit failure degradation or electrical shock Note s e Each time you plug in the AC Power Cord no operations will be performed for several seconds This is not a malfunction 112 No supplied cables are used with these connections e Please purchase the Necessary Cables at your local store Before you connect the AC Power Cord Be sure other Devices are connected properly before plugging in the AC Power Cord Selecting your Connection quality HDMI Highest quality Supports high definition Digital signals and gives highest picture and sound quality Video and Audio signals are combined in one cable You must use HDMI for full high definition Vid
12. 4 or LI the higher ratings will be Blocked Automatically The lower ratings will be available for viewing When you set the highest rating to LI All ratings turn to LI Automatically To Block any inappropriate programs set your limits in US movie ratings lock US TV ratings lock and Region ratings lock The Child Lock setting will be retained after a Power failure or after the Power is removed for longer than 10 seconds except the PIN code reverts to 0000 Child and Ratings Lock p 27 e Region ratings lock will be available when the Unit receives a Digital broadcast using the New rating system For the United States the Unit may download the Region Ratings Lock Table if required e The Canadian rating systems on this Unit are based on CEA 766 A and CRTC policy 2 7 English Channel lock Particular Channels or External Input modes can be invisible in this function 3 Use A Y to Select Channel lock then press OK 4 Use A Y to Select the Particular Channels or External Input then press OK Repeatedly to Switch between View and Block X indicates that the Channel or Input Source is Locked indicates that the Channel or Input Source is Not Locked LJ HDMI LJ HDMI2 L Video Features me O 40 1 40 2 Continued on next page Setting US Movie and TV Ratings US Movie Ratings Lock is the Rating System created by MPAA US TV Ratings Lock has Co
13. Modes are available SiO gt MONO gt DKA N a STEREO Outputs Stereo Audio SAP Outputs a Second Audio Program MONO Outputs Mono Audio Continued on next page EasyLink options If you have our brand products such as Blu ray Disc player or DVD recorder that are compatible with EasyLink functions connect them to this Unit via an HDMI cable so you can simply operate various items from this Unit s Remote Control Before you begin You must set On in Device control and EasyLink control gt p 30 Otherwise LINK does not work even if you connected our brand devices to this unit 1 Press B OPTIONS to display EasyLink options menu ESAN Device menu Device contents Device favorite Contro device he menu of your connected EasyLink Device menu Contro Discs Device contents he top menu of your DVD or Blu ray Device favorite Controls the pop up menu of your Blu ray Discs 2 Use A Y or OK on this Units Remote Control to operate the desired functions for your devices Note s Some of EasyLink functions may not be available depending on your EasyLink devices or Discs e You must connect this Unit to our brand EasyLink devices and be sure its EasyLink setting is also set to On We do Not guarantee 100 interoperability with other brands of HDMI link compliant devices Changing Picture Format Display Modes can be Selected when your TV receives a 16 9 or 4 3 Video
14. Weather Warnings and Others Locally originated Programming News Political Public Service Announcements Religious Sports Weather Change PIN Although the default PIN code 0000 is supplied with the Unit you can set your own PIN code 3 Use A V to select Change PIN then press OK 4 Press the NUMBER keys to enter the New 4 digit PIN code e Enter PIN code again in Confirm PIN entry field Enter PIN lo Features Confirm PIN Eo ES PIN Code Back Note s Make sure to enter a PIN code and the confirm PIN code must be exactly the same If they are different the space is cleared to reenter the New PIN code e When a Power failure occurs the PIN code will be erased and Unit returns to the default PIN code 0000 e If you forget the PIN code unplug the AC Power Cord then wait for 10 seconds to plug the AC Power Cord in again The Unit will restore the PIN code to 0000 factory default Then repeat the Change PIN procedure to Setup a New PIN code 29 PC settings This function lets you adjust the PC screen position clock and phase during PC Input Use lt 4 to adjust Clock setting to stabilize the PC screen and Phase setting to improve the clarity of the PC screen 1 Use A Y to select PC settings then press OK Auto adjustment Horizontal position Features Vertical position Clock Phase 2 Use A V to select the item you want to adjust then press OK e The ho
15. appear beside the Main Rating category in US TV ratings lock Menu You cannot Block a Sub Rating if the Main Rating is set to Changing the Category to I or WorL automatically changes All its Sub Ratings to the same Continued on next page English Canadian English or Canadian French Ratings You can select the Rating for Canadian English or Canadian French broadcasting 3 Use A Y to Select Canadian English rating or Canadian French rating then press OK 4 Use A Y to Select the Desired Rating then press OK Repeatedly to Switch between View and Block e X indicates that the Rating is Locked e Ll indicates that the Rating is Not Locked Canadian Canadian Da English rating French rating eee All Locked All Ratings For All Children 8 and Older Bans Unsuitable for Ages under 8 PG Paremal Guidance Suggested gt ams Unsuitable for Ages under 13 A A Unsuitable for Ages under 14 t6anst Unsui for Ages under 16 18anst Note s The V Chip can Block Non Rated Programs as per CEA 608 E sec L 3 If the Option to Block NR None or E Programs are used in US movie ratings lock US TV ratings lock Canadian English rating or Canadian French rating accordingly unusual results may occur and the Unit may not Receive Emergency Bulletins or other Types of Programming Emergency Bulletins Such as EAS messages
16. cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Wall Mount Bracket Kit Brand Model Screw dimension 32PFL3509 SANUS SAN18B MASTO with spacer The recommended Wall Mount Bracket Kit sold separately allows the mounting of the TV on the wall For detailed information on installing the wall mount refer to the Wall Mount Instruction Book P amp F USA is not responsible for any damage to the product or injury to yourself or others if you elect to install the TV Wall Mount Bracket or mount the TV onto the Bracket on your own The Wall Mount Bracket must be installed by experts 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Note to the CATV system installer This reminder is provided to call the CATV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical Example of Antenna Groun
17. computer is NOT in Sleep Mode when the Input Mode on this Unit is in PC mode Tap any Key on the Computer Keyboard to Wake it up No Color View other TV channels The problem might be limited to the broadcasting station Adjust Color in Picture settings p 22 Picture Poor Adjust Contrast and Brightness in Picture settings p 22 For the Best Picture Quality watch High Definition wide screen Programs f the HD content is Not available watch Standard Definition Programs instead You see Pixelation on the Screen When the capabilities of the Unit exceed the capabilities of the Digital Broadcasting the signal will be increased to match the capabilities of the Display on the Unit This may cause Pixelation Noise or Trash Unusual picture appears and the TV does Not Operate Press the Power key first If it does not solve the problem then press the keys on the Remote Control in the order shown below to change the Unit to the Live Mode SLEEP gt FORMAT gt D gt mp A mW ump CD Sound No sound distorted sound or incorrect Audio Sound is heard when using the HDMI DVI Connections Make sure that the Analog Audio signals from the HDMI DVI Device are connected to the Analog Audio L R Input jacks Refer to For PC Input signal p 19 When using Component Analog Video Composite Analog Video or PC VGA Video make sure that the Analog Audio L R connectors are mounted into the Audio L R Input ja
18. extended periods product cosmetic appearance items due to normal wear and tear unauthorized repair or other cause not within the control of Philips Damage or claims for products not being available for use or for lost data or lost software e Damage from mishandled shipments or transit accidents when returning product to Philips A product that requires modification or adaptation to enable it to operate in any country other than the country for which it was designed manufactured approved and or authorized or repair of products damaged by these modifications A product used for commercial or institutional purposes including but not limited to rental purposes e Product lost in shipment and no signature verification receipt can be provided e Failure to operate per Owner s Manual TO OBTAIN ASSISTANCE IN THE U S A CANADA PUERTO RICO OR U S VIRGIN ISLANDS Contact Philips Customer Care Center at 1 866 309 8147 REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY FOR THE CON SUMER PHILIPS SHALL NOT BE LIABLE FOR ANY INCIDEN TAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PROD UCT EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY Some states do not allow the exclusions or limitation of inciden tal o
19. it change Automatically Why are captions not displayed Entirely Or why are captions delayed behind the dialog Check the Antenna or Cable Connection to the Main Unit Check the Batteries on the Remote Control Re insert the Batteries with their Polarities as indicated Check if there is an obstacle between the infrared sensor window and the Remote Control Test the IR Signal Output use IR Signal Check gt p 36 If okay then possible Infrared Sensor trouble Aim Reduce the distance to the Unit he Remote Control directly at the infrared sensor window on the front of the Unit When there is an infrared equipped device such as PC near this Unit it may interrupt the Remote Control signal on this Unit Move the infrared equipped device away from this Unit change the angle of the Device s infrared sensor or Turn Off the infrared communication function Connect the RF Coaxial Cable directly to this Unit and run the Initial Setup Make sure to complete the Initial Setup before the Unit goes into Standby mode Autoprogram must be completed when you Set Up the Uni unavailable channels are broadcast for the First time or Move it to a location where previously Make sure Autoprogram has been completed p 24 The selected channel may not be broadcasting When Autoprogram is interrupted and not completed some channels will not be received Make sure to complete the Autoprogram gt p 24 The s
20. IN code follow the instruction for Change PIN English Be sure the RF cable is correctly connected to this Unit and you are registered with your Cable TV provider when you Install Cable channels 1 Use A Y to Select Autoprogram then press OK e If you run Autoprogram when you have Locked Channels a Message appears asking to enter your PIN Enter your PIN in order to Complete the Installation You need to reset or set the Channel Lock again after the Installation 2 Use A Y to Select an appropriate Option then press OK When Antenna is selected the TV Detects Any Off the Air Antenna Signals It searches for ATSC Digital and NTSC Analog Channels available in your Area When Cable is selected the TV detects signals supplied by Cable It searches for DTV Analog TV and Cable channels available in your area Back Auto program will rescan all channels Auto programming may take more than 20 minutes to complete Setup Antenna Select your signal source o Cable Ote pJ Urantia IN p 29 Cha Those nnel list The channels selected here can be skipped when selecting the channels using CH channels can still be selected with the NUMBER keys 1 Use A Y to select Channel list then press OK 2 Use A Y to select the channel you want to remove then press OK Highlight channels for Ch Up Down key selection BACK 0 4 Ch Select cx Watch Skip O Back
21. INFO to hide the information Note s e When the program guide consists of more than 4 lines use A W to scroll to the next previous lines No description provided is displayed when the program guide is not provided e While the TV screen information is displayed the Closed Caption function is interrupted In External Input mode the following screen is displayed Video e g When an External Device is connected to Video Input jack 400 Fso 3 Bjrvrcoisv ES The information display will Automatically disappear in 5 seconds 20 English 5 Making more use with your TV This section describes the overview of the Main Menu displayed when you press Re The Main Menu consists of the function setting items below Displaying the Main Menu 1 Press to display the Main Menu FORMAT Picture Settings assistant Auto picture Personal Backlight Contrast Brightness Color Tint Sharpness Advanced settings 21 2 Use A Y to select the desired Menu and an item then press OK or use A Y lt P to determine the setting Adjusting the Picture Mode or customize the Picture quality as your preference Adjusting the Sound Mode Equalizer and some other Sound functions Scanning the Channels available in your area and see what the Antenna Signal levels are Adjusting the Closed Caption Parental Guide and some other useful functions You can choose English Spanish or French as you
22. Online at www productrecords com phl today to get the very most from your purchase Registering your model with Philips makes you eligible for all of the valuable benefits listed below so don t miss out Register Online at www productrecords com phl to ensure Product Safety Notification By Registering your Product you ll receive notification Additional Benefits Registering your Product guarantees that you ll receive directly from the manufacturer in the rare case of a Product Recall or Safety Defect Know these safety symbols RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The caution marking is located on the rear or bottom of the cabinet all of the Privileges to which you re Entitled including special money saving offers The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of CAUTION La uninsulated dangerous voltage within the apparatus s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the apparatus To reduce the risk of fire or electri
23. Register your product and get support at www philips com support 32PFL3509 For further assistance call the customer support service in your country To obtain assistance contact Philips Customer Care Center EN User Manual In the USA Canada Puerto Rico or the US Virgin Islands 1 866 309 8147 M xico D F and rea Metropolitana 58 87 97 36 Interior de la Republica 01 800 839 19 89 ES Manual del Usuario Para obtener m s informaci n llame al servicio de soporte al cliente de su pa s Para obtener asistencia comun quese con Centro de atenci n al cliente de Philips FR Manuel d Utilisation En los Estados Unidos en Canada Puerto Rico o en las Islas Virgenes de los Estados Unidos 1 866 309 8147 M xico D F y Area Metropolitana 58 87 97 36 Interior de la Republica 01 800 839 19 89 Pour obtenir de l aide suppl mentaire communiquez avec le centre de service a la client le de votre pays Pour obtenir de l aide communiquez avec le centre de service a la client le Philips au Dans le Etats Unis au Canada a Puerto Rico ou aux les Vierges am ricaines 1 866 309 8147 M xico D F et rea Metropolitana 58 87 97 36 Interior de la Republica 01 800 839 19 89 PHILIPS Contents 1 Notice 2 Important Positioning the TV Regulatory Notices Environmental Care Preparing to Move Ship the Unit 3 Getting Started Features Supplied Accessories Symbols used in this User Manual Attaching the Base I
24. ain Verify that you have a cable connected to the ANTENNA IN jack on the back of the TV the channel installation process searches this connection If you are using a cable or satellite box please confirm the input which you have connected to the box and press SOURCE key on the remote control to select the appropriate source input After an Initial Setup is completed If you want to scan the channels Automatically again Autoprogram p 24 You can add the desired Cable and Analog channels not memorized by Autoprogram Add channels p 25 If you want to change to another Language Language p 31 If you want to change the Location setting Location p 31 If you want to restore the picture setting Settings assistant p 22 16 English 4 Use your TV Switching on your TV and putting it in Standby mode Remote Control To Turn the TV On from Standby or Off to Standby Press on the Side or Front panel or the Remote Control Note s Energy Consumption contributes to air and water pollution When the AC Power Cord is plugged in your TV consumes energy with a very low standby Power Consumption Adjusting Volume To decrease or increase Volume Press VOL lt P on the Front panel or press VOL on the Remote Control or the Side panel VOL lt Volume Down VOL Volume Up To mute or unmute sound
25. annel 2 16 MUTE Turns the Sound On and Off 13 VOL Adjusts the Volume BACK Returns to the previous Menu operation 5 FORMAT Adjusts the Picture size on the TV screen SLEEP Sets Sleep Timer cc Displays the audio portion of programming as text superimposed over the video Continued on next page Control Panel Terminals DO O R OR 10 English VOL lt gt Adjusts the Volume VOL lt 4 Volume Down VOL gt gt Volume Up In the Menu screen moves the Cursor Left lt 4 Right P cHa v Selects a Channel in the Memorized Channel Ring Low to High or High to Low In the Menu screen moves the Cursor Up 4 Down Y 3 MENU Opens the Main On screen Menu 4 SOURCE Selects Connected Devices POWER Turns the TV On and Off Standby mode Remote Control Sensor Receives IR Signal from Remote control D Power On Standby Indicator On lights in white Standby no light USB Terminal Data Input from USB Memory Stick only Do Not Connect any Device to this terminal such as Digital Camera eyboard Mouse etc Analog Audio L R Input jacks Connect Analog Audio Signals from HDMI DVI Analog Audio L R jacks Signal Component Video Analog Audio L R jacks Signal Composite Video Analog Audio L R jacks Signal e PC Connection Analog Audio L R jacks Signal with Stereo Mini 3 5m
26. aptions and Text Services The Closed Captions or Text is Displayed in CC 1 and T 1 the same Language as the Program s Dialog up to 4 lines of script on the TV Screen Serve as the preferred Data CC 3 and Channels The Closed Captions or T 3 Text is often a Secondary Language Caption service Rarely available and Broadcasters use them only in Special conditions such as when CC 1 and CC 3 or T 1 and T 3 are Not available There are 3 Display modes according to Programs Pai Displays Characters on the TV screen aint on mmediately Pop on Once Characters are Stored in Memory they are isplayed All at Once Displays the Characters Continuously by Scrolling max 4 lines You can choose the Font Size Color etc Background and other Characteristics of the Closed Captions Text Closed Captioning color and ransparency Font opacity can be opacity changed Background Background color Caption style color and transparency Background ity of th y Background pr yo E isplayed caption opacity can be switched Edge color Edge color and Edge ype of the Edge type displayed caption can be switched Picture display Font style Font size Font color and Font opacity Edge Edge color and Edge type Background Background color and Background opacity e Review your setting choice made above by looking in the upper right corner of the displayed setting box not All
27. c shock do not expose this apparatus to rain or moisture Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the WARNING apparatus CAUTION To prevent electric shock match wide blade of plug to wide slot fully insert ATTENTION prise et pousser jusqu au fond Pour viter les choc lectriques introduire la lame la plus large de la fiche dans la borne correspondante de la PHILI PS Visit our World Wide Web Site at www philips com support CHILD SAFETY PROPER TELEVISION PLACEMENT MATTERS THE CONSUMER ELECTRONICS INDUSTRY CARES e Manufacturers retailers and the rest of the consumer electronics industry are committed to making home entertainment safe and enjoyable e As you enjoy your television please note that all televisions new and old must be supported on proper stands or installed according to the manufacturer s recommendations Televisions that are inappropriately situated on dressers bookcases shelves desks speakers chests carts etc may fall over resulting in injury TUNE IN TO SAFETY e ALWAYS follow the manufacturer s recommendations for the safe installation of your television e ALWAYS read and follow all instructions for proper use of your television e NEVER allow children to climb on or play on the television or the furniture on which the television is placed e NEVER place the television on furniture that can easi
28. cks Sound Intermittent or No Sound Check if the Audio Cable is connected into the Unit correctly You Switch to a Different Input and the Volume Changes This Unit will Memorize the Volume Level from the last time you adjusted it Ifthe Volume of the Sound from another Device is Higher or Lower then the Loudness will Change Make sure Auto volume leveling is set to On p 23 Picture amp Sound No Picture or Sound Check if the Power is On Check whether All the cables to the Unit are connected to the correct Output jack of your device like Blu ray DVD Recorder View other TV channels The problem might be limited to the Broadcasting Station or Weak Signal Strength Unplug the AC Power Cord and wait for about 1 minute then Plug the AC ower Cord and turn On the Unit again heck whether the Connection of the Antenna or Cable Satellite Set top ox is connected correctly Make sure that the selected Input mode is connected to the working Input WTC A Q heck if your computer is NOT in sleep mode when the Input mode of this nit is in PC mode Tap any key on the keyboard to wake up your computer ake sure that the sound is not muted Press x so that the volume bar and urrent volume level will appear on the TV screen ake sure that the volume is NOT set to 0 or MX If so use VOL to adjust to the desired volume Adjusted Picture or Sound settings are not effective every time the Unit is tur
29. ding as per NEC National Electric Code ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT NEC SECTION 810 20 GROUNDING CONDUCTORS NEC SECTION 810 21 POWER SERVICE GROUNDING ELECTRODE ZA ELECTRIC SERVICE EQUIPMENT SYSTEM NEC ART 250 PART H P amp F USA is not liable for these types of accidents or injury noted below Install the Wall Mount Bracket on a sturdy vertical wall If installed onto a ceiling or slanted wall the TV and Wall Mount Bracket may fall which could result in a severe injury Do not use screws that are longer or shorter than their specified length If screws too long are used this may cause mechanical or electrical damage inside the TV set If screws too short are used this may cause the TV set to fall Do not fasten the screws by excessive force This may damage the product or cause the product to fall leading to an injury For safety reasons use 2 people to mount the TV onto a Wall Mounting Bracket Do not mount the TV onto the Wall Mounting Bracket while your TV is plugged in or Turned On It may result in an electrical shock injury When installing the unit on the wall allow this much space 11 8 inches 30cm 5 9 inches 15cm 3 9 inches 10cm Top Left and right side Bottom 1 Notice Trademarks are the property of Koninklijke Philips N V or their respective owners P amp F USA reserves the right to change products at any time without being obliged to adjust earlier supplies accordi
30. e please ensure enough space between the external devices and the Unit Do not insert the AC power cord into the power socket outlet before all the connections are made e Ensure that you always have easy access to the AC power cord or plug to disconnect the TV from the power Before you move the TV disconnect attached cables to prevent damage to connectors Be sure to unplug the AC power cord from the AC outlet before moving or carrying the Unit Regulatory Notices Do not place the Unit on the furniture that is capable of being tilted by a child and an adult leaning pulling standing or climbing on it A falling Unit can cause serious injury or even death This apparatus should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided Make sure to leave a space of 4 inches 10cm or more around this apparatus Press to turn the Unit on and go into standby mode To completely turn off the Unit you must unplug the AC power cord Disconnect the AC plug to shut the Unit off when trouble is found or not in use The AC plug shall remain readily available AC plug J Never use a gas duster on this TV The gas trapped inside of this Unit may cause ignition and explosion CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type WARNING Batteries battery pack or battery ins
31. e the product with a product that is new or which has been manufactured from new or ser viceable used parts and is at least functionally equivalent or most comparable to the original product in Philips current inventory or 3 refund the original purchase price of the product Philips warrants replacement products or parts provided under this warranty against defects in materials and workmanship from the date of the replacement or repair for ninety 90 days or for the remaining portion of the original product s warranty whichever provides longer coverage for you When a product or part is exchanged any replacement item becomes your property and the replaced item becomes Philips property When a refund is given your product becomes Philips property Note Any product sold and identified as refurbished or renewed carries a ninety 90 day limited warranty Replacement product can only be sent if all warranty requirements are met Failure to follow all requirements can result in delay WHAT IS NOT COVERED EXCLUSIONS AND LIMITATIONS This Limited Warranty applies only to the new products manu factured by or for Philips that can be identified by the trademark trade name or logo affixed to it This Limited Warranty does not apply to any non Philips hardware product or any software even if packaged or sold with the product Non Philips manufacturers suppliers or publishers may provide a separate warranty for their own products
32. elected channel cannot be viewed by the Child and Ratings Lock setting gt p 27 The Unit requires some kind of Antenna Input An indoor Antenna Digital or VHF UHF an External Antenna Digital or VHF UHF or an RF Coaxial Cable from your wall Cable Satellite Set top Box needs to be plugged into the Unit Check if the correct Input mode is selected by pressing 2 SOURCE or using CH Refer to Watching Channels from an External Device gt p 18 Check the Antenna Cable or other Input Connection to the Unit When using the Component Video Connection check that the Green Y Blue Pb Cb and Red Pr Cr connectors are connected to their corresponding colored jacks on the Unit Many Digital channels have alternate channel numbers The Unit changes the numbers Automatically to the ones signifying the Broadcasting Station s channel number These basic numbers used for the previous Analog Broadcasts e g Input Digital ch 30 Automatically changes to Digital ch 8 1 Closed Captions that are delayed a few seconds behind the actual dialog are common for Live broadcasts Most captioning production companies can display a dialog to maximum of 220 words per minute If a dialog exceeds that rate selective editing is used to insure that the Closed Captions remain up to date with the current TV screen dialog How can set the clock My PIN code no longer works how can change the Child Lock setting There is No clock fu
33. en set to maximize energy efficiency while delivering the best possible picture using the factory installed home mode settings Changing or enabling other features in this TV e g brightened backlighting will possibly increase energy consumption beyond the original ENERGY STAR qualified limits LED backlig ti g tec ology uses less energy when compared with a standard CCFL backlighting LCD Portions of this software are copyright The FreeType Project www freetype org television of the same screen size Actual energy savings will vary depending on the screen size The American Academy of Pediatrics discourages television viewing for children younger than two years of age English 2 Important Positioning the TV e Large screen TVs are heavy 2 people are required to carry and handle a large screen TV Make sure to hold the upper and bottom frames of the Unit firmly as illustrated e Install the Unit in a horizontal and stable position Do not install the Unit in direct sunlight or in a place subject to dust or strong vibration e Depending on the environment the temperature of this Unit may increase slightly This is not a malfunction Avoid a place with drastic temperature changes Do not place anything directly on top or bottom of the Unit Depending on your external devices noise or disturbance of the picture and or sound may be generated if the Unit is placed too close to them In this cas
34. enu 2 Use A Y to select English Espanol or Frangais then press OK Note s If you need the English menu instead of the Spanish or French menu s press A Use Y to select Idioma or Langue then press OK Use A Y to select English then press OK Press to Exit the Main menu Your TV is fitted with a USB Connection that enables you to view JPEG photos or watch Motion JPEG files stored on a USB Memory Stick 1 Connect the USB Memory Stick to the USB terminal on the side of your TV 2 Press A and use A Y to select USB then press OK e The Highlighted Text will move to Start now then press OK again Start n This menu allows you to enjoy your pictures and videos via your USB device 3 Use A Y to Select the Picture or Video then press OK These Recorded Files must meet Specifications shown below Video Motion JPEG Sampling frequency 32 kHz 44 1 kHz or 48 kHz Quantization bit rate 16 bit Audio type LPCM Note s Up to 2GB FAT16 or 8GB FAT32 capacity can be supported Up to 10 000 files or 1 000 folders with 19 hierarchies can be recognized Up to 255 English characters can be recognized This unit does Not Support MTP Media Transfer Protocol This unit supports FAT16 and FAT 32 file systems If the file is Not Supported an Error message appears When the USB Memory Stick is not recognized try reconnecting it again We cannot be held responsible if your USB Mem
35. eo and to enable EasyLink HDMI CEC Note s e Philips HDMI supports HDCP High bandwidth Digital Contents Protection HDCP is a form of Digital Rights Management that protects high definition content in Blu ray Discs or DVDs Component Y Pb Pr High quality x Supports high definition Analog signals but gives lower picture quality than HDMI Component Y Pb Pr Video cables combine red green blue Video cables with red white Audio L R Cables Match the cable colors when you connect to the TV Composite Basic quality R For Analog Connections Composite Video Audio Analog cable usually combine a yellow Video Cable with red white Audio L R Cables With this Unit yellow cable must be connected to Y green jack on the Component Video Input jacks Continued on next page English Connecting your Devices HDMI Digital Connection DMI Connection offers the Highest Picture quality DMI High Definition Multimedia Interface transports high definition igital Video and multi channel Digital Audio through a single cable J E 92 Set top box or gt Blu ray disc player or VE NO HD game console OUT a IN HDMI cable HDMI DVI Connection This Unit can be connected to your Device that has a DVI Terminal Use an HDMI DVI Conversion Cable for this Connection and it requires Audio Cable f
36. equipment has been tested and found to comply with the limits for a Class B Digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio or television technician for help Declaration of Conformity Trade Name PHILIPS Responsible Party P amp F USA Inc Model 32PFL3509 Address PO Box 2248 Alpharetta GA 30023 2248 U S A Telephone Number 1 866 309 8147 5 Modifications This apparatus may generate or use radio frequency energy Changes or modifications to this apparatus may cause harmful interference unless the modifications are expressl
37. ictures where the right side and left side differ Select the side that is most pleasing to you with the Left Right keys The energy consumption in the Standard setting is Energy Star qualified BACK MENU e ox Next O Back Ol Exit 6 Press dor P 3 times to select the side of the pictures that is the most pleasing to you then press OK e a e Va Ea a 10 sie tT 7 Press OK to finish Settings assistant Settings assistant You have set up your viewing preferences MENU Store Back Q Exit e When the initial setup is completed the lowest memorized channel with the confirmation message of the location setting will be displayed on the TV screen You must set Home in step 4 Otherwise Picture and Sound settings you adjusted will not be memorized after the unit goes into Standby mode Note s If you are not receiving a signal from your Cable service contact the Cable provider If you press do fk during Autoprogram this Setup of TV channels will be Cancelled The Initial Autoprogram function can be executed for either Antenna or Cable only Once When you change the Connection Antenna Cable select Autoprogram again mm p 24 Ifthere is no signal Input from the Antenna terminal and no operation for several seconds after you Turn On the Unit Helpful hints appears Follow the instructions listed on the TV screen Initial setup No channel is registered Try Autoprogram ag
38. ils We Do Not guarantee 100 interoperability with All Universal Remote Controls Symbols used in this User Manual The following is the description for the symbols used in this User Manual Description refers to Digital TV Operation If neither symbol appears the operation is applicable to both English Attaching the Base You must attach the base to the Unit to have it as a table top Unit Be sure the front and rear of the base match the proper direction For large screen TVs at least 2 people are required for these steps 1 Note s e Make sure to use a table which can support the weight of this Unit and is larger than this Unit Make sure the table is in a stable location e When attaching the base ensure that FRONT with arrow written on the bottom of the base is downward If it s not downward the 2 hooks don t fit into the base e When attaching the base ensure that All Screws are tightly fastened If the base is not properly attached it could cause the Unit to fall resulting in injuries as well as damage to the Unit To remove the base from this Unit unscrew the Phillips head screws in step 2 Be careful not to drop the base when you remove it Installing the Remote Control Batteries Slide the battery cover off the back of the Remote Control Insert the 2 Supplied Batteries AAA 1 5V Be sure the and ends of the Batte
39. ings for Picture and Sound 1 Use A Y to Select Location then press OK Caption settings Child lock PC settings Features EasyLink Location Software upgrade 2 Use A Y to select Home or Retail then press OK The Unit will be set up with predefined settings for retail displays In this setting the Power Retail Consumption may possibly exceed the limit requirement of the ENERGY STARS qualification This setting is ENERGY STAR qualified The Unit is set to maximize the energy efficiency Home for Home setting and it can be adjusted through a choice of Picture and Sound quality selections according to your preference Note s You must set Home in the Menu Otherwise personalized Picture and Sound Settings will Not Be Memorized after the Unit goes into Standby Mode E sticker When you set Location to Retail store E sticker Electronic Sticker is displayed E sticker can be Turned Off using procedure below 1 Use A Y to select E sticker then press OK 2 Use A Y to select Off then press OK You can Turn Off E sticker Top E sticker is displayed on top of the TV screen E sticker is displayed on bottom of the TV screen Note s e If you set Location to Home E sticker will not be displayed 31 English 1 Press fM and use A Y to select Language then press OK Select your menu language English Seleccione el idioma para el menu S lectionnez la langue du m
40. ize and weight e NEVER place your older CRT television on a dresser where children may be tempted to use the drawers to climb e ALWAYS make sure your older CRT television does not hang over the edge of your furniture English 4 English Important Safety Instructions Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth NOU a wpa Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a
41. l Full Unscaled This Unit can also be connected to your PC that has a DVI Terminal Use an HDMI DVI Conversion Cable for this Video Connection and it requires a Stereo Mini 3 5mm Plug Audio Cable for Analog Audio signal as well Refer to 16 9 Video Signal on this page if the PC has an HDMI Output Proportionately stretched picture Sidebars appear on both edges of the screen Stretched out of proportion to fill the screen Normal Unscaled Original size Continued on next page English TV Screen information You can display the currently selected channel or other information such as the aspect ratio on the TV screen In the Digital mode the detailed broadcasting information for the current off the air channel such as Program title are displayed 1 Press O INFO Digital TV Operation A Day of Memories 1 1 1 Rating information AAA 4 USTV TV MA US movie English 1 2 o ee I usTv TV PC US movie US TV TV G US movie 6 O Program title O Broadcast station STEREO es Hons JG TV PG DLSV Q Channel Number Switching channels gt p 17 Audio Language DTV Audio mode Analog TV Switching Audio Mode p 18 Program s image Aspect Ratio Changing Picture Format p 19 CC Not available if Closed Caption is set to Off Caption settings p 25 Child Lock rating Child and Ratings Lock p 27 2 Press
42. ly be used as steps such as a chest of drawers e ALWAYS install the television where it cannot be pushed pulled over or knocked down e ALWAYS route cords and cables connected to the television so that they cannot be tripped over pulled or grabbed CE org safety JE Consumer Electronics Association WALL OR CEILING MOUNT YOUR TELEVISION e ALWAYS contact your retailer about professional installation if you have any doubts about your ability to safely mount your television e ALWAYS use a mount that has been recommended by the television manufacturer and has a safety certification by an independent laboratory such as UL CSA ETL e ALWAYS follow all instructions supplied by the television and mount manufacturers e ALWAYS make sure that the wall or ceiling where you are mounting the television is appropriate Some mounts are not designed to be mounted to walls and ceilings with steel studs or cinder block construction If you are unsure contact a professional installer e Televisions can be heavy A minimum of two people is required for a wall or ceiling mount installation MOVING AN OLDER TELEVISION TO A NEW PLACE IN YOUR HOME e Many new television buyers move their older CRT televisions into a secondary room after the purchase of a flat panel television Special care should be made in the placement of older CRT televisions e ALWAYS place your older CRT television on furniture that is sturdy and appropriate for its s
43. m Plug Audio Cable on PC Digital Audio Output jack Digital Audio S PDIF Output to Home Theaters and other Digital Audio systems 11 HDMI Input jack s Digital Audio and Video Input from High Definition Digital Devices such as DVD Blu ray Disc players Cable Satellite Set top Boxes and PC s O 75 ohm Cable Antenna Connection Signal Input from an Antenna or Cable Satellite Set top Boxes Headphone Audio Output jack Headphone 3 5mm Stereo jack for personal listening Component Y Pb Pr Composite Video VIDEO Input jacks for VIDEO Composite Video Input VIDEO jack is a shared jack with Component Video Input Y jack 45 PC Input jack VGA cable Connection for PC Continued on next page Connecting Antenna or Cable Satellite IPTV Box Be sure your Antenna or another Device is connected properly before plugging in the AC Power Cord If connecting to an Antenna through an RF cable Any DTV Programs that are Broadcast in your area can be received for free through an Antenna Connection RF cable If you connect a Set top Box through an RF cable If the TV is connected to a Cable Satellite Set top Box via a Coaxial Connection set the TV to channel 3 4 or the channel specified by the service provider RF cable Set top Box If connecting Cable Satellite IPTV Box using an HDMI cable If the TV is connected to a Cable Satellite Set top Box via an HDMI cable
44. nction on this Unit If a Power failure occurs for longer than 10 seconds the child lock setting is retained but the PIN code is reset to the default code 0000 Refer to Child and Ratings Lock p 27 Continued on next page English 35 English Troubleshooting If the Unit does not perform properly when operated as instructed in this User Manual check the following Troubleshooting Tips and All Connections Once before calling for Service Power No Power Make sure the AC Power Cord is plugged in Make sure that the AC outlet supplies the proper voltage plug another electrical appliance into the AC outlet to ensure that the AC outlet operates normally Ifa Power Failure occurs Unplug the AC Power Cord for 1 minute to allow he Unit to Reset Itself Remote Control keys do not work Do NOT press more than one key at the same time Ensure that no keys on the Remote Control are depressed and move freely Universal Remote Control does not work properly Refer to the user manual of the universal remote control for the Philips code Picture Power is On but No Screen Image Check whether the Connection for the Antenna Cable or Satellite Set top Box is Connected Correctly Check whether All the Cables to the Unit are connected to the correct Output Jack on your separate Device like Blu ray Disc DVD Recorder Make sure that the selected Input mode is connected to the working Input jack Check if your
45. ned On Os lt e ZC You must set Home in Location p 31 Otherwise the settings you adjusted will not be memorized after the Unit goes into Standby Mode You see a Distorted Picture or Hear an Unusual Sound Analog TV NTSC signal You may be getting interference from electrical appliances automobiles motorcycles or fluorescent lights Try moving the Unit to another Location to see if this is the Cause of the Problem Ghosts lines or streaks in picture Analog TV NTSC signal Electrical interference from nearby appliances may affect picture quality View other TV channels The problem might be limited to the broadcasting station or weak signal strength Picture Poor Sound Intermittent or No Sound View other TV channels The problem might be limited to the broadcasting station or weak signal strengt a Screen You Switch to a different Input and the Screen Size changes This Unit will Memorize the Viewing Mode from the last time you used those Particular Input Modes The Display image does not cover the Entire Screen If you are using the Unit as a PC Monitor make sure that Horizontal position and Vertical position in PC settings are set correctly If you are watching TV or using the Composite Video Component Video or HDMI with 480i Input press FORMAT Repeatedly to Switch to various Screen Modes Different color marks on the TV screen View other TV chan
46. nels The problem might be limited to the broadcasting station missing data or pixelation due to weak signal strength Closed Captions Closed Captions are displayed as a white box No Closed Captions are displayed in the Closed Captions Supported Program Interference from buildings or weather conditions may cause captioning to be incomplete if watching Analog TV signals Broadcasting Station may shorten the program to insert advertisements The Closed Captions Decoder cannot read the information of a shortened program Black Box is displayed on the TV Screen The Text mode is selected For Closed Captions select CC 1 CC 2 CC 3 or CC 4 gt p 25 Note s The LCD screen is manufactured to provide many years of useful life Occasionally a few non active pixels may appear as a fixed point of blue green or red This is Not to be considered a Defect in the LCD screen Some Functions are not available in Specific Modes but this is Not a Malfunction Read the Description in this Manual for more Details on Correct Operations 8 Information Glossary Analog TV NTSC Acronym that stands for National Television Systems Committee and the name of Analog broadcasting standards Off the air Analog TV signals are no longer being sent by major broadcasting stations in the USA Aspect ratio The width of a TV screen relative to its height Conventional TVs are 4 3 in other words the TV screen is almost sq
47. nfrared pulsating light appears on the Display the Remote Control is sending out an IR signal Note Some Cameras have an IR Filter and will not Display the IR signal English 37 English 9 Specifications Model 32PFL3509 Type WXGA 1366 x 768 pixels 60Hz Diagonal Screen Size Aspect Ratio 31 5 169 Viewing Angles 178 V by 178 H Built in Digital Analog Tuner ATSC Digital NTSC Analog Sound ono Stereo Mono Stereo DTS TruSurround Power Output RMS watts Equalizer Ease of Use SD 4 3 Source Normal 16 9 Movie expand Zoom Wide HD 16 9 Source Normal 4 3 Movie expand Zoom Wide HDMI AV 4 3 Source Normal 16 9 Movie expand Zoom Wide Full HDMI AV 16 9 Source Normal 4 3 Movie expand Zoom Wide Full PC Source Normal Full Unscaled Refer to HDMI AV 16 9 Source above if PC has HDMI Output Photo Slide Show JPEG files only Video Playback Only Motion JPEG 320 x 240 30 fps with file extension avi will Playback Picture Format Terrestrial DTV ATSC E 2 13 F 14 69 Each Channel has e g 2 1 2 9 3 1 3 9 etc Terrestrial Analog NTSC 218 F 14 69 Channel Coverage 2 13 A W CAIN ls da W 1 W 94 Analog W 1 W 84 A 5 A 1 5A Tuning System Channel Frequency Synthesized Tuning System Direct Access Number Keyboard Programmable Scan Channel up down and PREV CH Previous Channel Co
48. ngly The material in this manual is believed adequate for the intended use of the system If the product or its individual modules or procedures are used for purposes other than those specified herein confirmation of their validity and suitability must be obtained P amp F USA warrants that the material itself does not infringe any United States patents No further warranty is expressed or implied P amp F USA cannot be held responsible neither for any errors in the content of this document nor for any problems as a result of the content in this document Errors reported to P amp F USA will be adapted and published on the P amp F USA support website as soon as possible Pixel characteristics This LCD product has a high number of color pixels Although tt has effective pixels of 99 999 or more black dots or bright points of light red green or blue may appear constantly on the screen This is a structural property of the display within common industry standards and is not a malfunction Warranty No components are user serviceable Do not open or remove covers to the inside of the product Repairs may only be done by Service Centers and official repair shops Failure to do so shall void any warranty stated or implied Any operation expressly prohibited in this manual any adjustments or assembly procedures not recommended or authorized in this manual shall void the warranty Federal Communications Commission Notice This
49. nnectivity Component Video Input 1 Y Pb Pr Supporting video signals 480i p 720p 10801 60Hz Composite Video Input Shared Y Green Terminal with Component 1 Video 2 HDMI Input Supporting video signals 480i p 720p 1080i 60Hz 1080p 24 30 60Hz PC Input signal up to WXGA 1360 x 768 Analog Audio UR Input eee via VGA HDMI and HDMI DVI Analog Audio L R Digital Audio ape Supporting Dolby Digital Headphone Output 18 inch 3 5mm 20V 10 60Hz 0 5 Operating Temperature 41 F 5 C to 104 F 40 C e Specifications are Subject to Change without Prior Notice Channel Access 10 Warranty PHILIPS LIMITED WARRANTY ONE WARRANTY COVERAGE PHILIPS warranty obligation is limited to the terms set forth below WHO IS COVERED Philips warrants the product to the original purchaser or the per son receiving the product as a gift against defects in materials and workmanship as based on the date of original purchase Warranty Period from an Authorized Dealer The original sales receipt showing the product name and the purchase date from an authorized retailer is considered such proof WHAT IS COVERED The Philips warranty covers new products if a defect in material or workmanship occurs and a valid claim is received by Philips within the Warranty Period At its option Philips will either 1 repair the product at no charge using new or refurbished replacement parts or 2 exchang
50. nnel for which you want to check the Digital signal strength gt ee TT Current 50 ch E Ch Change Note s Ifthe channel is set to an Analog channel or External Input you cannot confirm the Antenna condition 25 English Features 1 Display Setup using Home Menu and use A Y to select Features then press OK Caption settings Child lock PC settings EasyLink Features Location Software upgrade 2 Adjust the following items Caption settings Closed Captions displays the Audio portion of the Program as Superimposed Text over the Video 1 Use A Y to Select Caption settings then press OK Closed captions Caption service Digital caption service Features Caption style 2 Use A V 4 to select the Feature you want to use then press OK You can choose the Closed Caption display Off Closed Caption is not displayed Closed Caption is always displayed CCw Closed Caption is displayed when mute the Sound is Off Note s e You can cycle through the Closed Caption settings by pressing CC Closed captions n addition to the basic Closed Caption DTV has its own Closed Caption called Digital caption service Use this menu to change the settings for Digital caption service Select one of these before Digital caption changing any other ttem in service Caption settings menu Choose CS 1 under normal conditions Continued on next page The primary Closed C
51. nstalling the Remote Control Batteries Remote Control Control Panel Terminals Connecting Antenna or Cable Satellite IPTV Box Plugging in the AC Power Cord Selecting your Connection quality HDMI Highest quality Component Y Pb Pr High quality Composite Basic quality Connecting your Devices DMI Digital Connection DMI DVI Connection Component Analog Video Connection Composite Analog Video Connection Digital Audio Output Connection PC Connection USB Memory Stick Initial Setup 4 Use your TV Switching on your TV and putting it in Standby mode Adjusting Volume Switching Channels Watching Channels from an External Device Sleep Timer Switching Audio Mode EasyLink options Changing Picture Format TV Screen information ON ON Os ON ON 17 17 17 17 18 18 18 19 19 20 5 Making more use with your TV Displaying the Main Menu Picture Sound Setup Au oprogram Channel list Add channels An enna Confirmation Features Caption settings Chi PE Id and Ratings Lock settings EasyLink Set ing your Location to Home E sticker Language USB 6 Upgrade your TV Software Checking your Current Software version Upgrading the Software 7 Useful tips FAQ Troubleshooting 8 Information Glossary Maintenance 9 Specifications 10 Warranty 2 33 33 33 36 36 36 37 38 English 3 Register
52. ntrolled Access to Individual Programs based on their Age and Content rating 3 Use A Y to Select US movie ratings lock or US TV ratings lock hen press OK 4 Use A Y to Select the Desired Rating then press OK Repeatedly o Switch between View and Block e For US TV Ratings you can further set the Sub Ratings to Block Specific Elements within Programs e X indicates that the Rating is Locked e Z indicates that the Sub Rating is Locked Ll indicates that the Rating is Not Locked US movie ratings lock Features US TV ratings lock Features US Movie US TV ratings ratings TWY Appropriate for All Children MO E Appropriate for All Children 7 and Older General Audience Parental Guidance Suggested Description PG 13 Unsuitable for children under 13 TV 14 Unsuitable for children under 14 Restricted under 17 Requires Accompanying Parent or Adult Guardian o One under 17 Admitted ature Audience Only 28 To set the Sub ratings As for TV Y7 TV PG TV 14 or TV MA you can further set the Sub ratings to Block Specific Elements within programs To set the Sub ratings follow the step below Use A Y lt P to select the desired rating then press OK Repeatedly to switch between LW and FV Fantasy Violence Features STV rang TV Y7 FV Fantasy Violence TV PG D Dialog L Language TV 14 iolence Note s Blocked Sub Rating will
53. o use the USB Memory Stick which requires an External Power Supply 500mA or more Continued on next page English These Operations are accessible by Remote Control Some may also be accessible by the Main Unit s Control Panel Initial Setup This section will guide you through the Unit s Initial setting which includes selecting a Language for your On screen Menu and Autoprogram which Automatically scans and memorizes viewable channels Before you begin Make sure the Unit is connected to an Antenna or Cable 1 After making All the Necessary Connections press to Tum On the Unit It may take a few moments to Turn On the Unit for the first time Initial setup menu appears Automatically after the Unit is Turned On Use A Y to select the On screen language from the choices English Espa ol Frangais on the right side of the TV screen then press OK N uy Use A Y to select Antenna for TV channels or Cable for CATV channels then press OK Initial setup Make sure the antenna is connected to ANTENNA IN jack Select your signal source Antenna cal IES Cable Or J ado JE ANTENNA IN Antenna When Antenna is selected the TV detects Antenna signals It searches for DTV and Analog TV channels available in your area When Cable is selected the TV detects signals supplied by Cable It searches for DTV Analog TV and Cable channels available in your area Autopr
54. oftware when Upgrades are available New Software can be Downloaded from our website at www philips com support using the model number of your TV to find information Checking your Current Software version 1 Press A and use A Y to select Features then press OK 2 Use A Y to select Software upgrade then press OK Current software info Upgrade Features 3 Use A Y to select Current software info then press OK The version and a description of the Current Software is displayed Release Version XXXXXXX_XX_XX_XXXX_XX Features Upgrading the Software You can Upgrade the Software by using a USB Memory Stick Preparing for the Software Upgrade You require the following equipment A PC with web browsing capability An archive utility that supports the ZIP format e g WinZip for Windows or Stuffit for Mac OS A Blank empty clean formatted USB Memory Stick Note s Only FAT DOS formatted portable memory is supported Use only Software Upgrades that can be found on the Philips website 33 English Downloading the Software Find information and Software related to your TV and Download the Latest Software Upgrade file to your PC 1 on your PC open a web browser and go to www philips com support 2 Enter the model number in the Type the Model Number field 3 Click the desired Software to be Downloaded Decompress the ZIP file 4 Copy the Upgrade file to the Empty
55. ogram will begin Initial setup Please wait while the system is scanning for channels Auto programming may take more than 20 minutes to complete of o ooo O Digital channels Och Analog channels Och 15 English 4 Use A Y to select the desired Location setting then press OK Home is the ENERGY STAR qualified setting Initial setup Location Home is recommended for normal home use and is ENERGY STAR qualified In the Retail store mode all settings are fixed Home Select Home the Unit is set to maximize the energy efficiency for home setting and it can be adjusted through a choice of Picture and Sound quality according to your preference Use this setting o remove the E sticker if visible on the display p 31 e You must set Home in step 4 Otherwise Picture and Sound settings you adjusted will not be memorized after the Unit goes into Standby mode e When the Initial setup is completed the Lowest Memorized Channel with the confirmation message of the Location setting will be displayed on the TV screen e Select Retail the Unit will be set up with predefined settings for retail displays In this setting the Power Consumption may possibly exceed the limited requirement limit of the ENERGY STAR qualification 5 When you select Home press OK to begin Settings assistant Settings assistant Settings assistant helps you customize picture settings You will see a series of test p
56. ompatibility The Unit accepts 480i 480p 720p 1080i and 1080p Video signals HDMI DVI Connection requires separate Audio Connections as well and the Audio signals are Output as Analog L R Audio DVI does not display 480i image which is not in compliance with EIA CEA 861 861B USB Memory Stick This unit offers easy Playback of Picture JPEG and Video Motion JPEG files Insert the USB Memory Stick into the USB terminal shown below USB p 32 E Note s e The Unit recognizes only a USB Memory Stick Do Not use a USB hub or an extension cable to connect an External hard disk drive to the Unit Not Supported A USB Memory Stick is always inserted to this Unit directly A USB Memory Stick is Not Supplied with this Unit We Do Not guarantee that All USB Memory Sticks can be supported by this Unit Be sure to keep a backup copy of the original files on your Device before you play them back on this Unit We have no responsibilities for damage or loss of your stored data To protect your USB Memory Stick files from being erased place the write protect sliding tab in the protect position e When you are ready to remove a USB Memory Stick set the Unit to go into Standby mode to avoid any damage to your data and the Unit A USB Memory Stick that requires its own driver or the Device with a special system such as fingerprint recognition are Not Supported This unit is not allowed t
57. ontain Errors or there might be no captions at all Some possible causes of poor quality signals are Automobile ignition noise Electric motor noise Weak signal reception ultiplex signal reception ghosts or screen flutter Data dropout and Pixelation for DTV only The Unit retains the Closed Caption setting if the Power fails e When the Unit receives special effects Playback signal e g Search Slow and Still from a VCR s Video Output channel ch3 or ch4 the Unit may not display the correct caption or text The EUT setting that satisfies 79 102 e is as follows Font Mono font Character Size Large Continued on next page English Child and Ratings Lock You can prevent your children from watching certain Programs or certain Channels by locking the TV Controls and by using Ratings 1 Use A Y to select Child lock then press OK Caption settings Child lock PC settings EasyLink Location Features Software upgrade 2 Use the NUMBER keys to enter the 4 digit numbers for your PIN code e When you have not set up your PIN code enter 0 0 0 0 e When the PIN code is correct Child lock menu is displayed See the following description for setting each item Channel lock US movie ratings lock US TV ratings lock Features Canadian English rating Canadian French rating Region ratings lock Change PIN Note s e When you select a rating and set it to
58. or Analog Audio signal as well Cable Receiver or IN i Satellite Set top Box 02 Audio UR abl with the DVI Output jack a o aa IN HDMI DVI OU conversion cable Note s Use an HDMI cable with the HDMI logo a certified HDMI cable High Speed HDMI cable is recommended for the Better compatibility For HDMI Connection e The Unit accepts 480i 480p 720p 1080i 1080p 24 30 60Hz of Video signals 32kHz 44 1kHz and 48kHz of Audio signals This Unit accepts 5 1 channel Audio signal Dolby Digital and 2 channel Audio signal LPCM This Unit accepts only signals in compliance with ElA861 For HDMI DVI Connection The Unit accepts 480i 480p 720p 1080i and 1080p Video signals HDMI DVI Connection requires separate Audio Connections as well and the Audio signals are Output as Analog L R Audio OUT DVI does not display 480i image which is not in compliance with EIA CEA 861 861B 13 English Component Analog Video Connection Component Analog Video Connection offers Better Picture quality for Video Devices connected to the Unit If you connect to the Unit s Component Video Y Pb Pr Input jacks connect Analog Audio Cables to the Analog Audio L R Input jacks M i OUT Set top box Audio L R cables pb a E 043 Component Y Pb Pr OUT vidko cables Blu ray disc DVD recorder
59. ormat that produces high resolution and high picture quality PIN code A stored 4 digit number that allows access to Parental control features SAP Seconda Second Audio channel delivered separately from the Main Audio channel This Audio channel is used as an alternate in bilingual broadcasting SDTV Standard Definition TV Standard Digital format that is similar to the Analog TV picture quality Audio Program 36 Maintenance Cabinet Cleaning Wipe the front panel and other exterior surfaces of the Unit with a soft cloth Never use a solvent or alcohol Do Not spray insecticide liquid near the Unit Such chemicals may cause damage and discoloration to the exposed surfaces Panel Cleaning Wipe the panel of the Unit with a soft cloth Before cleaning the panel disconnect the AC Power Cord Servicing Should your Unit become inoperative Do Not try to correct the problem yourself There are no user serviceable parts inside Call our toll free customer support line found on the cover of this User Manual to locate an Authorized Service Center IR Signal Check If the Remote Control is not working properly you can use a Digital or Cell Phone Camera to see if it is sending out an infrared signal e g With a Digital Camera Point the Digital Camera towards the Remote Control infrared diode at the front of the Remote Control Press any key on the Remote Control and look at the Camera Display If an i
60. ory Stick is Not Supported nor will we accept any liability for damage or loss of stored data To protect your USB Memory Stick files from being erased place the write protect sliding tab in the protect position Be sure to keep a backup copy of the original files on your device before you play them back on this Unit This unit does not recognize USB Memory Stick that requires a special driver This unit is not allowed to use the USB Memory Stick which requires an External Power Supply 500mA or more A file name exceeding 128 characters or contains a dot character is Not Supported on this TV Progressive JPEG files are Not Supported Only a Motion JPEG file with an avi extension is supported An extension mov is Not Supported During Motion JPEG Playback Pause Forward and Reverse Do Not Work on this Unit 32 Picture JPEG 1 Use A Y to select the desired file then press OK Picture Picture Image1 jpg Go to root folder Image1 jpg Image1 jpg 1024 768 2009 04 02 17 42 06 Thumbnails Press OK key to play pause e To toggle between List and Thumbnails press the NUMBER 2 key each time The unit goes to the Slide show Automatically To Pause Play the Slide show press OK Use the NUMBER keys 1 through 4 to see the file details Y or change the following settings Y EJ See the description in table below Deal Press 1 to display file detail
61. packaged with the bundled product Philips is not liable for any damage to or loss of any programs data or other information stored on any media contained within the product or any non Philips product or part not covered by this warranty Recovery or reinstallation of programs data or other information is not covered under this Limited Warranty This warranty does not apply a to damage caused by accident abuse misuse neglect misapplication or non Philips product b to damage caused by service performed by anyone other than Philips or Philips Authorized Service Location c to a product or a part that has been modified without the written permission of YEAR Philips or d if any Philips serial number has been removed or defaced or e product accessories or consumables sold AS IS without warranty of any kind by including refurbished Philips product sold AS IS by some retailers This Limited Warranty does not cover e Shipping charges to return defective product to Philips e Labor charges for installation or setup of the product adjust ment of customer controls on the product and installation or repair of antenna signal source systems outside of the product e Product repair and or part replacement because of improper installation or maintenance connections to improper voltage supply power line surge lightning damage retained images or screen markings resulting from viewing fixed stationary con tent for
62. r On screen Language You can view Picture JPEG and Video Motion JPEG files stored on a USB Memory Stick 3 When the Setting is completed press Mor BACK to Exit English Picture Before you begin You must set Home in Location p 31 Otherwise personalized Picture and Sound settings will not be memorized after the Unit goes into Standby Mode 1 Press A and use A Y to select Picture then press OK Picture Settings assistant Auto picture Personal Backlight Sharpness Advanced settings 2 Use A V lt P to select the item you want to adjust then press OK o guide you through the best picture setting o select the desired setting then press OK Personal Standard Vivid Sports Movie Game Auto picture and Eco When you adjust the following settings Personal picture will be set Automatically Pr o Reduce Power Consumption and Reduce Backlight Brightness ncrease Power Consumption and Brightness Backlight Brightness o Decrease Brightness to Increase Brightness o Decrease Color o Increase Color ntensity ntensity o Add Red o Add Green o Select the desired Setting then press OK Color alignment Noise reduction Black Color Advanced settings stretch Dynamic contrast and Gamma 22 English You can set a Particular Picture Quality using Advanced settings Picture Color alignment Noise reduction Black stretch Dynamic contrast Color alignment
63. r consequential damages or allow limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights You may have other rights which vary from state province to state province P amp F USA Inc PO Box 2248 Alpharetta GA 30023 2248 38 English PHILIPS P amp F USA Inc PO Box 2248 Alpharetta GA 30023 2248 U S A P amp F Mexicana S A de C V Av La Palma No 6 Col San Fernando La Herradura Huixquilucan Edo de M xico C P 52787 Philips and Philips Shield are used under license of Koninklijke Philips N V A4AF2UT kk kkk
64. ries line up with the markings inside the case 3 Slide the cover back into position Note s Remove the Batteries if not using the Remote Control for an extended period of time 8 Continued on next page English Remote Control PREV CH PHILIPS 9 English C O POWER Turns the TV On from Standby or Off to Standby O EasyLink HDMI CEC buttons gt Begins or Restarts the Disc Playback H Pauses the Disc Playback a Stops the Disc Playback lt lt gt P Searches Backward or Forward through the Disc Note s e You must set On in the Master EasyLink p 19 to operate the above functions G SAP Selects Audio mode MONO STEREO SAP Audio language 4 A MENU Displays the main menu WINFO Displays Information about the current program A Y lt P NAVIGATION keys OK Moves the cursor Selects the On screen Menu items B OPTIONS Opens EasyLink options menu Note s e You must set On in the Master EasyLink p 19 to operate the above functions I SOURCE Selects Connected Devices CH Selects a Channel in the Memorized Channel Ring Low to High or High to Low COLOR keys Use these Keys according to the directions On screen 11 O 9 NUMBER keys Used to enter a Channel Program number e DOT Use with 0 9 to select Digital channels For example to enter 2 1 press as an O PREV CH Returns to the previously viewed Ch
65. rizontal vertical position clock and phase of the PC screen are Automatically adjusted Select if you want to adjust Automatically oe ee ee Horizontal to move PC screen Se to move PC screen left position right to move PC screen Vertical position down to move PC screen up to decrease setting value to increase setting value Note s e You may not obtain an appropriate screen with Auto adjustment for some signals In this case please adjust the settings manually e Properly adjust the Clock setting and then adjust the Phase setting Continued on next page English EasyLink This function allows you to operate the linked functions between our brand Devices with a EasyLink feature and this Unit connecting through an HDMI cable You must connect this Unit to our brand EasyLink devices and be sure it s EasyLink setting is also set to On 1 Use A V to select EasyLink then press OK Master EasyLink Auto device off Auto Von is Features Device control Device list 2 Use A V lt P to select the item you want to adjust then press OK Set the Master EasyLink On or Off The following additional settings will be grayed out when you set them to Off Disables All EasyLink Master EasyLink Selects if you have connected an External Device that is compatible with the EasyLink function You can set your connected EasyLink device to Tum Off by interlocking from this Unit s Power
66. root directory on the clean formatted USB Memory Stick Starting the Software Upgrade Warning When the Software Upgrade is running don t press any keys Do Not remove the USB Memory Stick during the Software Upgrade e Ifan Error occurs during the Upgrade retry the procedure or for further assistance please contact the Call Center 1 Connect your USB Memory Stick with the Upgrade file to the USB Service Port on the side of your TV Use only the Unit s Front Panel Keys to enter the following Instruction Steps 2 to 6 Press MENU and use A Y to select Features then press OK Use A Y to select Software upgrade then press OK Use A Y to select Upgrade then press OK maw N Read the On screen instructions and confirm that you want to continue with the Installation Would you like to upgrade the software Features 6 When the Software Upgrade is com leted press to set the Unit PE P P into Standby mode then remove the USB Memory Stick and then press o again to Turn the Unit back On e The TV starts up with the New Software For further assistance please contact the Call Center 7 Useful tips 34 FAQ Question My Remote Control does not work What should do How come the Initial Setup appears every time Turn On this Unit Why can not watch some RF signal TV Programs How come there is no image from the Connected External Devices When enter a channel number why does
67. s below g Name Album Date Size and Next More Detail Press 1 again to remove file details Press 4 or OK to start the Slide show Start show While the Slide show is on the following 2 settings will be displayed Press 2 then use A Y to select the transition mode choosing from None Dissolve Wipe right Wipe left Wipe up Wipe down Box in and Box out Press 3 then use Y to change the display time choosing from Short g play g Slide time Medium and Long Press 4 or OK to stop the Slide show Stop show While the Slide show is Off the following 2 settings will be displayed Every press on 2 will turn the picture clockwise by 90 degrees Rotate Press 3 then use A Y to select the zoom factor 1x 2x or 4x Press Zoom OK to set the zoom factor Transitions Video Motion JPEG 1 Use A Y to select the desired file then press OK Video MOVIE1 avi Go to root folder Title MOVIE1 avi HE MOVIE avi Director Date 2009 04 02 Duration 00 06 37 Supported format motion jpeg 320 x 240 30FPS e To stop Playback and return to the file list press BACK OK or CH e Press CH to play back from the beginning Press 1 to display file details below Title Director Date and Duration More Detail Press 1 again to remove file details English 6 Upgrade your TV Software Philips continuously tries to improve its products and we strongly recommend that you Upgrade the TV S
68. selections show the differences selected 26 Note s Closed Caption will NOT be displayed when you are using an HDMI Connection Digital caption service that you can switch differs depending on the broadcast description e Caption style will not have any effect if the User setting is set to Off The captions do not always use correct spelling and grammar e Not all TV Programs and product commercials include Closed Caption information or All types of the Closed Captioning Refer to your area TV Program listings for the TV channels and times of Closed Caption shows The captioned programs are usually noted in the TV listings with abbreviations such as CC To show the Closed Caption on your TV screen Broadcast signal must contain the Closed Caption data Captions and texts may not exactly match the TV voice Changing channels may delay the Closed Caption for a few seconds Adjusting or muting the volume may delay the Closed Caption for a few seconds Abbreviations symbols and other grammatical shortcuts may be used in order to keep pace with the on screen action This is not a malfunction The caption or text characters will not be displayed while the main menu or functions display is shown If a black box appears on the TV screen this means that the Closed Caption is set to the text mode To clear the box select CC 1 CC 2 CC 3 or CC 4 If the Unit receives poor quality television signals the captions may c
69. some sound operations such as volume up can be changed by using this Unit s Remote Control to Output Sound from the Unit s Speakers Off not to Output Sound from the Unit s Speakers TV speakers to Control Audio Output from your connected EasyLink Compliant Devices with VOL by using this Unit s Remote Control Speakers EasyLink Before you begin Make sure the Unit is connected to Antenna or 1 Press f and use A Y to select Setup the Cable n press OK Autoprogram Channel list Add channels Antenna 2 Adjust the following items Autoprogram 24 Autoprogram Please wait while the system is scanning for channels Auto programming may take more than 20 minutes to complete Digital channels 10 ch Analog channels 6ch e When the Scanning and Memorizing of Available Channels is Completed the Lowest Memorized Channel will be Displayed Note s After setting Autoprogram using CH skips unavailable channels Automatically e If you are not receiving a signal from your Cable service contact the Cable provider If you press do fi during Autoprogram the Setup of TV channels will be Cancelled Even if Autoprogram is completed the channel setting will be lost if the AC Power Cord is unplugged before the Unit goes into Standby mode by pressing O The PIN Code will be required Once you set a PIN code in the Child and Ratings Lock mm p 27 e If you want to change your P
70. talled shall not be exposed to excessive heat such as sunshine fire or the like WARNING To prevent injury this apparatus must be securely attached to the furniture wall in accordance with the instructions Tipping shaking or rocking the unit may cause injury death 6 English Environmental Care The packaging of this product is intended to be recycled Contact your local authorities for information about how to recycle the packaging For product recycling information please visit www recycle philips com End of Life Directives Philips pays a lot of attention to produce environmental friendly products in green focal areas Your new TV contains materials which can be recycled and reused At the end of its life specialized companies can dismantle the discarded TV to concentrate the reusable materials and to minimize the amount of materials to be disposed of Please ensure you dispose of your old TV according to local regulations Disposal of Used Batteries The Batteries supplied do not contain the heavy metals mercury and cadmium Nevertheless in many areas Batteries may not be disposed of with your household waste Please ensure you dispose of Batteries according to local Regulations Preparing to Move Ship the Unit Please pack the Unit properly by following the Diagram on the Carton O To avoid damage to the Screen do not pack the stand on the same side as the TV screen 3 Getting Started
71. uare widescreen models are 16 9 the TV screen is almost twice as wide as its height CEC Consumer Electronics Control This allows you to operate the linked functions between our brand devices with CEC feature and this Unit We Do Not guarantee 100 interoperability with other brands of CEC compliant devices Component Video This is a Video signal format that conveys each of 3 principal colors of light red blue and green through different signal lines This allows the viewers to experience picture colors as original as it is There are several signal formats including Y Pb Pr and Y Cb Cr Dolby Digital The system developed by Dolby Laboratories to compress Digital sound It offers Stereo Sound 2ch or multi channel Audio DTS TruSurround Enable DTS TruSurround to enhance your audio experience DTV ATSC Abbreviation that stands for Advanced Television Systems Committee and the name of the Digital broadcasting standards E sticker E sticker is showing set features technical information etc on this TV set that is displayed on the TV screen mainly used by TV retailers Previously the information was on a printed sticker that was put on the display HDMI High Definition Multimedia Interface Interface that supports All uncompressed Digital Audio Video formats including Set top Box Blu ray DVD Recorder or Digital television over a single cable HDTV High Definition TV Ultimate Digital f
72. use A Y to select Sound then ek This setting is not interlocked when you change the Output mode by pressing SAP Refer to Switching Audio Mode p 18 to Output Stereo Audio Audio setting to Output Mono Audio Auto sound Standard Equalizer DTS TruSurround ii Auto volume leveling Oi to Output Second Audio Program TV speakers On Digital output format Bitstream Audio setting Stereo 2 Use A V lt P to select the item you want to adjust then press OK to select the desired setting then press OK Personal Standard Vivid Sports Movie Music and News Auto sound When you adjust the following settings Equalizer DTS TruSurround and Auto volume leveling Personal sound will be set Automatically Adjust the tonal quality for each frequency to adjust each level of tonal quality Press BACK to go back to the previous menu Equalizer This selects Sound Modes for more spatial or Surround Sound reproduction Off to set DTS TruSurround to Off DTS TruSurround On to set DTS TruSurround to On This function keeps a constant loudness level between the TV commercials and the Programs to Remove the Auto volume leveling Auto volume to Reduce Volume Differences leveling between the TV Commercials and the Programs You can select the Audio Output from the Unit s speakers or not If your amplifier is HDMI link function compatible and connected by an HDMI cable to this Unit
73. ws your other HDMI link devices to be controlled by the HDMI cable connected o your TV HDMI Input e HDMI DVI Input f your Video Device has a DVI Output jack use an HDMI DVI Conversion Cable to connect he Unit Component Video Input PC Input nput from a Computer AV Input Audio and Video Input from an External Device USB terminal The Picture JPEG and Video Motion JPEG files stored on a USB Memory Stick can be played back on this Unit e Digital Audio Output Digital Audio Supporting Dolby Digital sent to Home Theaters and other Digital Audio systems Headphone Audio Output Headphone 3 5mm Stereo jack for personal listening T Supplied Accessories User Manual Quick Start guide TV base and Screws Screws packed with this Unit Remote Control and Batteries AAA 1 5V x 2 Model Quantity Size 32PFL3509 3 M4 x 0 551 14mm Cw w Note s e Ifyou lose the Screws please purchase the above mentioned Phillips head Screws at your local store e If you need to replace these accessories please refer to the part name or No with the illustrations and call our toll free customer support line found on the cover of this User Manual When using a Universal Remote Control to operate this Unit Make sure the component code on your Universal Remote Control is set to our brand Refer to the instruction book accompanying your Remote Control for more deta
74. y approved in the User Manual The user could lose the authority to operate this apparatus if an unauthorized change or modification is made Cables Connections to this device must be made with shielded cables with metallic RFI EMI connector hoods to maintain compliance with FCC Rules and Regulations Canadian notice CAN ICES 3 B NMB 3 B Standard Television Receiving Apparatus Canada BETS 7 NTMR 7 Copyright All other registered and unregistered trademarks are the property of their respective owners The terms HDMI and HDMI High Definition Multimedia Interface and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries H M HIGH DEFINITION MULTIMEDIA INTERFACE Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories DOLBY DIGITAL For DTS patents see http patents dts com Manufactured under license from DTS Licensing Limited DTS the Symbol amp DTS and the Symbol together are registered trademarks and DTS TruSurround is a trademark of DTS nc DTS Inc All Rights Reserved dts TruSurround ENERGY STAR is a joint program of the US Environmental Protection Agency and the U S Department of Energy helping us all save money and protect the environment through energy efficient products and practices ENERGY STAR Consumer Notice This TV has be

Philips 32PFL3509/F7 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents