Phantom Tech Viewpoint VI0508 User's Manual
Contents
1. Installing the Mounting Bracket Remove the backing of the adhesive strip on the back of the Mounting Bracket Insert the bottom of the Mounting Bracket into the track of the Bottom Rail on the hinge side of the door Push the Mounting Bracket upwards ensuring that the top of the Corner Cover is tight against the upper portion of the door frame Using a level ensure that the Mounting Bracket is positioned plumb Then press the Mounting Bracket firmly against the door frame allowing the adhesive tape to temporarily hold it in place Move the Sliding Bar and Mesh off to the side as indicated in the illustration Using the provided screws secure the Mounting Bracket to the door frame Return the Sliding Bar and Mesh back to its original position in front of the Mounting Bracket Door Frame Top Sliding Bar Mounting Bracket Door Frame Installing the Top Rail and Catch Fra Installing the Top Rail 1 Remove the backing of the adhesive tape on the top of the Top Rail Insert the Rollers at the top of the Sliding Bar into the Top Rail then push the Top Rail into the Corner Cover on the top of the Ush ip Mounting Bracket Pt ounting Bracke ome Cove Insert Rollers Position the Top Rail along the top of the door gt se frame at a 90 angle to the side mounting surfaces Making sure that the Top Rail is tight against the side2. Tension Wire Make sure that the Viewpoint Screen will fit the door This application will accommodate an opening of up to 36 914 mm wide and between 76 9 16 1 947 mm and 80 9 16 2 047 mm high If the door opening is larger than that the Viewpoint Screen can still be installed by attaching a filler strip under the door frame to reduce the height of the door opening Refer to page 6 for details Catch Frame Sliding Bar Bottom Cap NOTE The Viewpoint Screen can only be shortened by 4 100 mm to a minimum height of 76 9 16 1 947 mm If the door opening is smaller than this the Viewpoint Screen will not accomodate the door Is the Door Opening Square For the Viewpoint Screen to operate effectively the door opening must be perfectly square Using a Carpenter Square check to ensure that the door frame is square If not use shims to bring the door frame to square before beginning installation Bottom Rail Is there enough Mounting Surface The Viewpoint Screen is a recess mount screen that installs on the inside surface of the door frame A minimum Mounting Surface of 1 3 4 45 mm is required This Mounting Surface must be flat and flush and at a right angle 90 to the door om Viewpoint Screen Mounting S
3. mm Cut from each part the cut off length provided by the calculation performed above Do NOT remove the tape that keeps the components of the Screen Housing Assembly secure until all cutting is complete ae After cutting any part of the atc rame ff Viewpoint Screen use a file to remove any burrs from the E 7 surfaces NOTE Safety glasses should be worn at all times during the cutting process _ ra a Cut off Length Cut off Length Installing the Bottom Rail and Preparing the Screen Housing Installing the Bottom Rail Remove the backing from the double sided tape on the bottom of the Bottom Rail Attach the Bottom Rail onto the door sill placing the front edge of the Bottom Rail even with the face or front edge of the door frame on both sides of the opening Bottom Rail Preparing the Screen Housing Assembly 1 Before installing the Screen Housing Assembly rotate the Mounting Bracket so that the Tension Wires are no longer wound around it Failing to do so prior to installing the Mounting Bracket will restrict the motion of the Tension Wires and prevent the screen from operating Attach the Sliding Bar Bottom Cap to the bottom of the Sliding Bar using the two screws provided Insert the Corner Cover onto the top of the Mounting Bracket Ye Sliding Bar Ya aN T KN Sliding Bar Bottom Cap Sliding Bar
4. of the door frame opposite the Mounting Bracket press firmly in place allowing the adhesive tape to temporarily hold it in place Using the 5 8 16mm screws provided secure the Top Rail to the door frame Installing the Catch Frame 1 10 Insert the bottom of the Catch Frame inside the Bottom Rail and the top of the Catch frame into the Top Rail Position it against the door frame on the opposite side of the Screen Housing Assembly Lift the Catch Frame upward into the Top Rail as far as it will go and secure to the door frame using the provided wood screws Push up the top of the Catch Frame all the way into the Top Rail Door Frame e Mounting Bracket Top Rail Catch Frame Adjusting the Latch Pull the Sliding Bar over to the Catch Frame and ensure that the Latch can be engaged If the Latch cannot be engaged adjust it by following the procedure shown in the diagram Loosen the screw adjust the height of the Latch until it engages with the Sliding Bar Tighten the screw careful not to over tighten Adjusting the Tension Wires 1 Slide the Sliding Bar to the opposite end to engage the Latch Push the entire mesh over to the Sliding Bar so that only the Tension Wires are visible in the opening of the door Loosen the screw of the top most Tension Wire Adjuster Slide it up or down until snug without any sag in the Tension Wire Tighten the screw to secure it
5. Installation Manual for IEWPOINT Retractable Screen Solutions For Right and Left Hinged Doors Durable Reliable Attractive For door openings up to 36 914 mm wide and 80 9 16 2 047 mm high Quick and Easy to Size and Install P PHANTOM S C R E E N 5 True to you Pure Phantom Congratulations and thank you for purchasing Viewpoint The Viewpoint Screen is designed and manufactured by Seiki Screen Systems the world s largest manufacturer of retractable screens Phantom Screens North America s leading brand of retractable solutions is proud to bring you these innovative products Thanks to rigorous design and product testing the Viewpoint Screen will provide years of dependable operation Plus it comes with a factory supplied limited lifetime warranty on all parts against manufacturer s defects Viewpoint was designed for easy sizing and installation This Installation Manual provides a step by step guide through the entire process Any questions Contact our Help Line Toll Free at 1 877 446 7180 Eil ae SCREEN SYSTEMS True to you Pure Phantom Index Getting to Know the Viewpoint Screen 4 Parts and 1001 scence isuacieisniounineaune 5 Measuring the Door Opening ceeeeseeereee
6. NOTE do not over tighten the tension on the Tension Wire If any of the other Tension Wires are sagging perform the same procedure with each adjuster If any of the situations below occur follow the appropriate procedure to correct the situation After adjusting the tension move the Sliding Bar two or three times to check the operation of the Viewpoint Screen Situation 1 Situation 2 t t m cw p Solution 1 Solution 2 Keep the topmost Tension Wire Adjuster fixed loosen the remaining Adjusters Starting from the bottom Adjuster adjust the tension of each wire to remove the gap as well as any sag in the Tension Wires To correct this situation reverse the steps in Situation 1 starting from the top Adjuster Adjusting the Latch and Tension Wires Tension Wire k Tension Wire Adjuster Screw Situation 3 Loose Tension Wire Solution 3 Tighten the tension of the loose Tension Wire to the same tension as the other Tension Wires Eea Loosen the screw to move up and down 11 Attaching the Fixing Strip 1 and Installing the Clips Attach the Fixing Strip Insert one edge of the Fixing Strip into the Mounting Bracket on an angle beginning at the top and working toward the bottom Again fro
7. m the top press the other edge of the Fixing Strip into the Mounting Bracket working it into position all the way to the bottom so that it is now fully inserted into the Mounting Bracket Fixing Strip Sliding Bar Mounting Bracket Installing the Clips Install the Clips into the Mounting Bracket evenly between the Tension Wires keeping the ribbed face of the Clip facing outward Refer to the diagram Clip Fixing Strip The Viewpoint Screen Installation is Now Complete 2 Service and Maintenance Hints The Viewpoint Screen is designed and engineered to be maintenance free The following are some helpful hints to ensure the smooth operation of the Viewpoint Screen for years to come e All moving components used in the Viewpoint Screen are manufactured from a mixture of nylon and other materials This combination of compounds is strong impact resistant and self lubricating Do not use oil grease oil based sprays or lubricants on any of the components on the Viewpoint Screen These products attract dirt and debris and may cause the Viewpoint Screen to react abnormally However the periodic application of a dry silicon lubricant to the moving parts is permissible e We recommend that while not in use the Viewpoint Screen be kept in the retracted position This will help extend the life of the screen mesh In the retracted position the mesh is p
8. rotected and kept clean e The Screen Mesh and Bottom Rail should be kept free of dirt and debris Lightly vacuum to remove any obstructions from the Screen Mesh and Bottom Rail Before installing the Viewpoint Screen please take the time to read the installation instructions thoroughly 13 Help Hotline The Viewpoint Screen was designed for easy sizing and installation This Installation Manual provides a step by step guide through the entire process If there are any questions during the installation of the Viewpoint Screen please call toll free 1 877 446 7180 5 i PHANTOM SCREEN SYSTEMS 14 True to you Pure Phantom Viewpoint Screen Limited Lifetime Non transferable Manufacturer s Warranty The Viewpoint Screen is warranted by Seiki Screen Systems to be free of manufacturer s defects in materials or workmanship for as long as the original purchaser owns and or resides at that residence and that the product remains at its original point of installation Seiki Screen Systems will repair or replace at its discretion any component within the terms and conditions of this warranty which is deemed as being defective from the manufacturing process upon proof of purchase This warranty excludes the screen mesh Furthermore thi
9. s dimension in the box below labeled H NOTE If the height of the door opening is greater than the maximum height requirement it is still possible to install the Viewpoint Screen Simply attach a filler strip under the top of door frame to reduce the height of the opening to at least 80 9 16 2 047 mm Be 13 4 45 mm mounting surface Door Sill sure to attach the filler strip before taking the height measurement Filler strip Cutting the Horizontal and P l Vertical Parts Cutting the Horizontal Parts Calculate the correct cut off Lengths Maximum Opening Subtract inside door Enter Cut off Length Width frame width W Below 36 914 mm Cut from each part the cut off length provided by the calculation performed above eo oe E a Rail N onai After cutting any part of the ei ee TRN lt Viewpoint Screen use a file o lt he n to remove any burrs from the si ie RUA Ix surfaces C t ane Cut Off Length Cutting the Vertical Parts Calculate the correct cut off Lengths NOTE Cutting of the Screen Housing Assembly must take place from the bottom of the unit note the Cut No Cut labels No more than 4 100 mm can be cut from the Screen Housing Assembly Maximum Opening Subtract inside door Enter Cut off Length Height frame height H Below 80 9 16 2 047
10. s 6 Cutting the Horizontal and Verical Pare inca mie euatenncninada 7 Installing the Bottom Rail and Preparing the Screen Housing Assembly 8 Installing the Mounting Bracket 0 0 0 0 cesses 9 Installing the Top Rail and CA AIG ceicewoaeniauacasione 10 Adjusting the Latch and Tension Wif Sssnsanisnacinsdinnuneniii 11 Attaching the Fixing Strip and Installing the CIPS sresrrsnsoncenninris 12 Service and Maintenance Hints e 13 For installation on a double hinged door French Doors you will need two Viewpoint Screens and one Double Door Kit Please refer to the Installation Manual within the Double Door Kit prior to starting The Viewpoint Screen is not intended for installation on a Sliding Patio Door Getting to Know the Viewpoint Scree Before beginning become familiar with the Viewpoint Screen and the door on which it will be installed The Viewpoint Screen accommodates both in swing and out swing doors In swing doors open to the inside of the home and require the Viewpoint Screen to be installed on the outside of the home Out swing doors open to the outside of the home and require the Viewpoint Screen to be installed on the inside of the home Top Rail Sliding Bar Latch Latch Hole Does the Viewpoint Screen fit the Door Opening Rollers Door Frame Corner Cover Mesh Mounting Bracket LSS Clip Fixing Strip
11. s warranty does not cover components damaged through improper use or installation or if components have been altered from their original state in a manner not otherwise prescribed in the Viewpoint Screen Installation Instructions This warranty is strictly limited to defective components only This non transferable limited warranty excludes labor breakage or damage due to normal wear and tear lack of maintenance as illustrated in our Installation Instructions or use for other than residential applications accidents and acts of god Replacements or repairs made subject to this lim ited warranty are otherwise warranted for the balance of the original warranty period Seiki Screen Systems liability under this limited warranty is restricted to the corrective actions as set forth herein and contrarily repudiates all incidental and consequential damage It is the responsibility of the consumer to notify Seiki Screen Systems of missing components within 30 days of the purchase of the Viewpoint Screen The Viewpoint Screen is designed to assist in keeping unwanted insects from the home it is in no way intended as a safety or security device to prevent access by individuals animals or small children Liability for any damages including but not limited to general special indirect incidental consequential aggravated punitive or exemplary damages and economic loss as well as for breach of any expressed or implied warranties including but no
12. t limited to implied warranties of merchantability quality and fitness for any purpose other than as prescribed herein is disavowed and omitted here from to the extent that such a disclaimer and preclusions are permitted by the laws of any particular jurisdiction Maintenance Keep Bottom Rail clean and free of debris Periodic use of silicone spray to the rollers on the top of the Sliding Bar is recommended do not use petroleum based lubricants Viewpoint Screen Designed and Manufactured by Seiki Screen Systems INSTALLATION INSTRUCTION MANUAL For warranty claims Call 1 877 446 7180 Or email info seikiscreensystems com iS Designed amp Manufactured by Seiki Screen Systems Marketed and Distributed by Phantom Screens PHANTOM True to you Pure Phantom Seiki Screen Systems Phantom Mfg Int l Ltd Call 1 877 446 7180 Call 1 888 PHANTOM Or email info seikiscreensystems com Or email phantom phantomscreens com www seikiscreensystems com www phantomscreens com 2008 Phantom Mfg Int l Ltd amp Seiki Screen Systems V10508
13. urface Parts and Tools Before beginning make sure that all these M parts are included with the Viewpoint Screen 5 8 16 mm package Pan Head Screws Q A 12 pcs 9 1 2 12 mm Flat Head Screws 2 pcs Top Rail g isu kemiy Catch Frame not required for a double door application Bottom Rail Ge Re Sliding Bar Corner Cover Bottom Cap Clips 5 pcs Required Tools Hack saw Measuring tape Carpenter Philips Electric drill Level Pen square screwdriver Viewpoint Screens can be sized and installed using common household tools Make sure all necessary tools are available before beginning NOTE A chop saw can be used in place of a hacksaw provided that a bi metal blade has been properly installed Measuring the Door Opening The Viewpoint Screen requires a minimum Mounting Surface of 1 3 4 45 mm This mounting surface must be flat and flush and at a right angle 90 to the door For the Width Measure the width of the opening between the right and left surfaces of the door frame record this dimension in the box below labeled W For the Height Measure the height of the opening between the underside of the top of the door frame or filler strip and the top of the door sill at a point 1 3 4 45 mm from the front surface of the frame Record thi
Download Pdf Manuals
Related Search