Perle Systems S-110P User's Manual
Contents
1. Perle PoE PoE 10 100 Ethernet Media Converters Installation Guide S 110P S 110PP S 110P SFP S 110PP SFP P N 5500318 12 Overview This document contains instructions necessary for the installation and operation of the Perle Standalone PoE PoE 10 100 rate converting Media Converters S 110P These products have the ability to convert 10 100Base T cable connections copper to 100Base X connection fiber The Perle media converters function as a PoE switch and support a variety of port configurations These media converters function as Power Sourcing Equipment PSE and can power up one Powered Device PD using standard UTP cables that carry Ethernet data The S 110P models are compatible with Powered Devices that comply with the IEEE 802 3af standard and the S 110PP models are compatible with Powered Devices that comply with both the IEEE 802 3af and the 802at 2009 standards The fiber connection can be either single mode SM or multimode MM and can operate over different wavelengths and distances depending on the model selected see table below POE POE PoE P Connector Mode Wavelength PoE PP xx Distance TX RX 5 1 10PP M2ax2 SEST TAPER 1310m 5 1 10P 52120 Fe 20 kin 12 4 mi Bb 5 L1OPP Su40 SC ST ETAN 1310 nm 5 1 10PP S2ax80 SESI 30 kin 49 7 mi LE 5 110PP Sex120 pak 120 km74 6 1550 nm S 110PP S1SC20U ac 20 12 4 mi POP S LIOPP SISC20D aC 20 kin 12 42. 70 13F to 158F 5 to 90 non condensing Operating Temperature Storage Temperature Operating Humidity Storage Humidity 5 to 95 non condensing Operating Altitude Up to 3 048 m 10 000 ft Dimensions 80 mm by 120 mm by 26 mm No Power MTBF supply POE POE 1 SFP 1 copper ports 437 237 hours 229 220 hours 81 386 hours 1 SC ST 1 copper 385 526 hours 214 161 hours 79 404 hours Fiber Optic Specifications PoE P Mode Wavelength TX Power RX Power Budget PoE PP nm dB dB dB S 110P M2xxC2 MM TX 1310 Min 20 Min 31 11 S 110PP M2xxC2 RX 1310 Max 12 Max 14 S 110P S2SC20 SM TX 1310 Min 18 Min 32 14 S 110PP S2SC20 RX 1310 Max 7 Max 3 S 110P S2ST20 SM TX 1310 Min 15 Min 32 17 S 110PP S2ST20 RX 1310 Max 8 Max 3 S 110P S2xx40 SM TX 1310 Min 5 Min 34 29 S 110PP S2xx40 RX 1310 Max 0 Max 3 S 110P S2SC80 SM TX 1550 Min 5 Min 34 29 S 110PP S2SC80 RX 1550 Max 0 Max 3 S 110P S2ST80 SM TX 1550 Min 5 Min 34 29 S 110PP S2ST80 RX 1550 Max 5 Max 3 S 110P S2SC120 SM TX 1550 Min 0 Min 35 35 S 110PP S2SC120 RX 1550 Max 5 Max 3 19 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide S 110P S2ST120 TX 1550 Min 0 Min 35 s 110PP s2sT120 M Rx 1550 Max 5 Max 0 2 S 110P S1SC20U SM TX 1310 Min 14 Min 32 18 S 110P
3. two devices in the event that one of the devices becomes overwhelmed with data The Perle media converter can generate and respond to Pause messages If Auto negotiation is set to On the media converter will advertise symmetrical and asymmetrical pause If Auto negotiation is set to Off the Pause receive and send will be disabled 16 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide Troubleshooting General e Ensure power is supplied to the media converter Only the Perle provided power supply may be used e Ensure the remote device s fiber connection type is compatible with the media converter If using a simplex fiber connection ensure that you have both an Upstream U and Downstream D media converter e Ensure all cabling is of the correct type and is in good working order e For duplex fiber connections ensure the RX and TX has been reversed between the two media converters No connectivity If unable to get full connectivity with all DIP switches in the UP position this procedure is recommended for troubleshooting Method 1 1 Set the Link Pass Through mode to Standard on both media converters Leave all other switches in the Up position 2 Connect the copper device to the copper port on the media converter The LKC LED light indicates good copper connection If the LKC LED is not lit then check the copper cable and the attached device 3 Repeat for the far end media converter 4 Connec
4. type of device detection required If the device type is unknown the default should be used as per IEEE802 3af at standards Enabled When enabled the media converter will perform Power Sourcing Equipment PSE functions as per IEEE802 3af POE or 802 3at 2009 POE standards Disabled When disabled the media converter will not perform PSE functions PD Power Reset Switch 6 Switch Position Mode Up default Disabled Down Enabled Disabled When disabled the loss of fiber link has no effect on PSE power to the PD device Enabled When enabled if the media converter detects loss of link on the fiber port it will turn off PSE output power to the PD device connected to the copper port After 2 seconds the media converter will restore power to the PD and the power will remain on until the fiber link transitions from a link up to link down state Loopback Fiber Switch 7 Switch Position Mode Up default Disabled Down Enabled Disabled The loopback feature is disabled This is default position for normal operation The switch must be set to this position in order for data to pass through the media converter Enabled This is a test mode All data received on the receive RX fiber connection is looped back to the transmit TX fiber connection The data link will be disabled however power to the 9 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide p
5. P S1SC20U RX 1550 Max 8 Max 3 S 110P S1SC20D SM TX 1550 Min 14 Min 32 18 S 110PP S1SC20D RX 1310 Max 8 Max 3 S 110P S1SC40U SM TX 1310 Min 8 Min 33 25 S 110PP S1SC40U RX 1550 Max 3 Max 3 S 110P S1SC40D SM TX 1550 Min 8 Min 33 25 S 110PP S1SC40D RX 1310 Max 3 Max 3 S 110P SFP S 110PP SFP SFP Note 1 Note 1 Note 1 Note 1 Fiber Cabling Requirements MM 50 125 microns or 62 5 125 microns SM 9 125 microns Ethernet Copper Cabling Requirements e Category 5 UTP or STP e 24 22 AWG e Straight through or Ethernet crossover Note Please refer the product page on the Perle website for the most up to date models and specifications http www perle com 20 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide Compliance Information FCC This product has been found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions in this Guide may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his her own expen
6. dia Converter Installation Guide 100 Copper Port On 100 Mbps valid link and detected speed is 100 Mbps Off 10 Mbps if link is currently established LKC Link Status on Copper port On Copper link is present Off No copper link present Blinking fast Copper link up and receiving data PSE Solid Green Active The PSE has successfully detected a compliant PD and is applying power over UTP Solid Orange Inactive The PSE is not active The PSE has been configured to provide power however e acompliant PD not detected no power applied e aPSE has turned off power for Reset function Off Disabled The PSE function is disabled in the configuration Error conditions A blinking red light is an error condition The led light will cycle with a 3 second stop interval between the error condition code PSE LED 1 blink PD Capacitance too high 2 blinks PD Resistance too low or short circuit 3 blinks PD Resistance too high 15 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide Other Features Auto MDIX Auto MDIX automatic medium dependent interface crossover detects the signalling on the 10 100BASE T interface to determine the type of cable connected straight through or crossover and automatically configures the connection Pause IEEE 802 3xy Integrated Pause signalling is an IEEE feature that temporarily suspends data transmission between
7. gh Mode In this mode the link state on one connection is directly reflected through the media converter to the other connection If link is lost on one of the connections then the other link will be brought down by the media converter If the installation has a media converter on both ends of the fiber link and both are set up for Link Pass Through then a loss of copper link on the far end device will propagate through both media converters and will result in a loss of link at the near end device Standard Mode In this mode links on the fiber and copper sides can be brought up and down independently of each other A loss of link on either the fiber or copper port can occur without affecting the other connection Link Pass Through Behaviour A Remote Media Converter setup for Far End Fault Enabled Auto negotiation OFF and Link Mode Standard B Local Media Converter setup for Far End Fault enabled Link Pass Through On and Auto negotiation OFF 1 A Loses fiber connection on its receiver 2 A Sends FEF 3 B Detects FEF signal and shuts down the fiber link 7 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide 4 B Drops link on copper connection because Link Pass Through is configured 5 A Link on copper connection is not affected because Link Pass Through Mode is set to Standard Far End Fault Switch 3 Switch Position Fiber Port Up default Enabled Do
8. mi 1930310 am 5 110PP S1SC40U a NUS Din 5 1 10PP SISC40D 20 km24 9 mi 132015 100m 5 1 10PP SFP SFP NOTE 1 2 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide Installation The default DIP switch settings all switches in the UP position will work for most installations These are the steps required to configure the Perle S 110P Ethernet media converter 1 Insert SFP Module SFP Model only eo OG GO IN Power up the media converter Power Sourcing Pinouts Set the DIP switch settings if required Set the Powering Option Jumpers if required Install and connect the fiber cable Install and connect the copper cable Install the Power cord Relief clip optional When Power Sourcing is enabled on a copper port the S 110P will provide power to the connected PD device over the Ethernet cable see PSE function on Dip Switch configurations The wire pairs on the cable used for delivering power will depend on the device The following options are available PoE Option RJ 45 Alternative A Alternative B Legacy 1 positive 2 positive 3 negative 4 positive negative 5 positive negative 6 negative 7 negative positive 8 negative positive 3 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide UTP copper Power PoE e IEEE 802 3af PoE up to 15 4 Watts for the UTP port PoE e IEEE 802at 2009 PoE e Up to 30 Wat
9. only 1 Locate the appropriate fiber module and insert the SFP into the opening on the front of the media converter 2 Ensure the SFP module is properly seated The release latch of the SPF fiber transceiver must be in the closed up position before insertion 3 The SFP module may be inserted before or after applying power to the media converter 4 Proceed with cable connections Installing the Duplex Fiber Cable Locate a 100Base X compliant duplex 2 strands fiber cable with appropriate connectors Connect the fiber cables from one media converter to the other media converter switch fiber device ensuring that the RX and TX are reversed crossed at the opposite end iol i TX TX Perle Media Perle Media Converter Converter 11 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide ne the Simplex Fiber Cable Locate a 100BASE X compliant simplex 1 strand fiber cable with appropriate connectors Ensure that the TX wavelength matches the RX wavelength at the other end and the RX wavelength matches the TX wavelength at the other end e Connect the fiber cable from one media converter to the other media converter switch fiber device Installing the Copper Cable e Locate 10 100Base T compliant copper cables with the appropriate connectors e Connect the RJ 45 cable between the Perle media converter and the device Attaching the Power Cord Strain Relief Clip 1 Remove the screw from the cha
10. owered devices will be maintained This mode will override all other switch settings Bank 2 Speed Copper Switch 1 Switch Position Copper port Up default 100 Down 10 100 When Switch 1 is in the Up position the S 110P will force the speed to 100 Mbps 10 When Switch 1 is in the Down position the media converter will force the speed to 10 Mbps Duplex Copper Switch 2 Switch Position Copper port Up default Full Duplex Down Half Duplex Full Duplex In the Up switch position the media converter will be set to Full Duplex mode Half Duplex The media converter will be set to Half Duplex mode Duplex Fiber Switch 3 Switch Position Copper port Up default Full Duplex Down Half Duplex Note When Auto negotiation SW1 is set to Off the media converter will use this Duplex setting for the copper port Full Duplex In the Up switch position the media converter will be set to Full Duplex mode 10 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide Half Duplex The media converter will be set to Half Duplex mode Auto MDIX Switch 4 Switch Position Copper port Up default Auto Down MDIX Auto In the Up switch position the media converter will automatically detect the Ethernet cable s polarity MDIX The S 110P will operate as a MDIX device Installing the SFP Fiber Module SFP models
11. se EN 55022 Class A WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures EN 55024 Class A Laser Safety IEC 60825 1 2007 This product meets Class Laser safety requirements per IEC 60825 1 2007 standard and complies with FDA CDRH 21 CFR1040 10 and 21CFR1040 11 WARNING Visible and invisible laser radiation may be present when cables are not connected Do not stare into the beam or view the beam directly with optical instruments Failure to observe this warning could result in an eye injury or blindness WARNING Use of controls adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure 21 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide Warranty Registration Perle s standard Lifetime Warranty provides customers with return to factory repairs for Perle products that fail under the conditions of the warranty coverage Details can be found at http www perle com support_services warranty shtml Contacting Technical Support Contact information for the Perle Technical Assistance Center PTAC can be found at the link below A Technical Support Query may be made via this web page www perle com support_services support_request shtml Copyright 2011 Perle Systems Limited All rights reserved No part of this doc
12. ssis that is closest to the power cord connector 2 Feed the power cord through the opening in the power cord relief clip 3 Attach the power cord relief clip to the chassis and secure with the provided screw 4 Plug the power cord into the AC power connector at the rear of the chassis 12 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide 5 Plug the other end of the power cord into an appropriate power outlet Powering up the Perle Media Converter 13 Connect the Perle supplied power adapter to the media converter Connect the power adapter to a power source Check that the PWR LED is lit Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide Operation Status LED The Perle PoE PoE 10 100 Rate converting Media converters have status LEDs located on the front panel of the unit 10 100Base T C Pst 100Base X AN 2 100 PR en J LKC PWR On Power is applied to the unit Blinking slow Loopback mode fiber interface is in loopback mode Blinking fast Power On failure See LED Pattern to determine pattern combination and failure cause LED Pattern LKF LKC 100 Off Off On SFP incompatible Internal hardware failure All other LED patterns LKF Status on Fiber Link On Fiber link is present Off No fiber link present Blinking fast Fiber link up and receiving data 14 Perle PoE PoE 10 100 Ethernet Me
13. t the fiber cable to both media converters The LKF LED indicates good fiber connection If no LKF LED then check the fiber cabling Ensure the transmitter and receiver pairs are crossed 5 Return units to desired configuration Method 2 The fiber connection can also be verified by configuring the remote media converter for loopback mode The LKF LEDs on both media converters should be lit Data should pass through the local converter over the fiber connection to the remote media converter At the remote media converter the data will be looped 17 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide back and passed through the fiber back to the local converter and passed to the copper link No Power to the PD e Ensure that the PD is compatible with the S 110P If the PD is a POE device then a POE media converter must be used S 110PP e Ensure that the power supply being used is the one provided with the product e If the PD does not support Alternative A including Legacy PD s the Power Option Jumpers must be set accordingly Also ensure the correct pin out for the device e For proper detection of different classes of devices the dip switches must be set correctly 18 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide Technical Specifications The following applies to all S 110P media converters Power Input Consumption 48V DC to 56V DC 6W OCT to 50 32F to 122F 25 to
14. ts on UTP port e PoE models will also support 802 3af PDs Type 1 and PoE PDs Type 2 Powering Options Jumper Settings Note The factory settings for Power Sourcing Pinouts will work for most installations as 802 3a and 802at 2009 POE POE devices will detect and sync to the correct POE option However in the rare case that you need to modify the settings the procedure is below In order to select a powering option the Power Options Jumper settings must be set Each copper port has a set of Power Option jumpers To access the Powering Options Jumper settings unscrew the six side screws on the case and remove the cover plate Locate the Power Option jumper set and strap the option pins as detailed below A a ee Alternative B gt mauve 3 ee ly FE 4 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide DIP Switches The DIP switches for Bank 1 are accessible through the opening in the side of the enclosure Bank 1 1 Auto nesotiation 3 Far End Fault 2 Link Mode 4 PSE Power 5 PSE Power PD Power Reset Bank 2 To access the DIP switches for Bank 2 unscrew the six side screws on the case and remove the cover plate Locate the jumper set as detailed below Dip switches 5 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide Bank 2 1 Speed Copper 2 Duplex Copper 3 Duplex Fiber 4 Auto MDIX 1234 Note All switch changes take effect immediately S
15. ument may be reproduced or used in any form without written permission of Perle Systems Limited 22 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide
16. witch changes will cycle power to the PD only if the PD Reset switch is set to On or you make changes to the PSE Power switches DIP Switch Settings Bank 1 Auto negotiation copper Switch 1 Switch Position Copper Port Up default Auto Down Off Note Auto negotiation should only be turned off if the copper link partner does not support Auto negotiation and fixed settings are required by the copper link partner Auto When enabled the media converter will negotiate with its link partner to determine the most optimal parameters for this connection The S 110P will advertise capabilities of 10 and 100 Mbps full and half duplex as well as pause to the link partner If the copper link partner does not support Auto negotiation the S 110P will parallel detect to 10 or 100 Mbps and force Half Duplex mode as per IEEE specifications Off When the Auto negotiation switch is set to the OFF position the media converter will not negotiate the Ethernet parameters 6 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide with the copper link partner The parameters used by the media converter will be determined by the Copper Speed Bank 2 switch 1 and Duplex Copper Bank 2 switch 2 DIP switch settings Pause receive and send will be disabled Link Pass Through Mode Switch 2 Switch Position Mode Up default Link Pass Through Mode Down Standard Mode Link Pass Throu
17. wn Disabled Enabled If the media converter detects a loss of signal on the fiber receiver it will immediately disable its fiber transmitter signal on the same port This in effect notifies the fiber link partner that an error condition exists on the fiber connection If the remote media converter is set up for Far End Fault FEF and the local media converter is set up with Link Pass Through a loss of fiber link on either the transmit or receive line will be passed through to the local copper connection thus notifying the connected device If the media converter has been set to Link Pass Through mode the effect will be the same as FEF since the link loss on the fiber receiver will result in bringing down the copper link which will in turn cause the transmit fiber link to be brought down Note This feature only takes affect if Auto negotiation Switch 1 has been turned Off Disabled The media converter will not monitor for or generate Far End Fault PSE Enable Copper Switch 4 and 5 Switch Position 4 Switch Position 5 Type PSE enabled Up default Up default normal detection PSE enabled Up Down High capacitance detection Down U PSE enabled p Legacy device 8 Perle PoE PoE 10 100 Ethernet Media Converter Installation Guide detection Down Down PSE disabled These switches must be set in order to enable the power sourcing function and to indicate the
Download Pdf Manuals
Related Search