Pentair 720 User's Manual
Contents
1. D Pentair Water Pool and Spa Prowler 720 ana 730 Robotic Inground Pool Cleaners Installation and User s Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Customer Service you have questions about ordering Pentair replacement parts and pool products please use the following contact information Customer Service 8 A M to 5 P M Eastern and Pacific Times Phone 800 831 7133 Fax 800 284 4151 Technical Support Sanford North Carolina 8 A M to 5 P M Eastern Time Phone 919 566 8000 Fax 919 566 8920 Moorpark California 8 A M to 5 P M Pacific Time Phone 805 553 5000 Ext 6312 Fax 805 553 5502 Web site visit www pentairpool com or www staritepool com to find information about Pentair products 2006 Pentair Water Pool and Spa Inc All rights reserved This document is subject to change without notice 1620 Hawkins Ave Sanford NC 27330 919 566 8000 10951 West Los Angeles Ave Moorpark CA 93021 805 553 5000 Trademarks and Disclaimers Prowler and the Pentair Water Pool and Spa logo are trademarka of Pentair Water Pool and Spa Inc Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products Pentair Water Pool and Spa Inc disclaims any proprietary interest in trademarks and trade names other than its own P N P121542. Cart Prow ler 720 Photo shows the Prowler 720 in a convenient protective cradle for easy storage and transport also available for the Prowler 730 model Prowler 720 and 730 Installation and User s Guide Operating the Prowler 720 and 730 Cleaners A WARNING Your Cleaner should not be used while people are swimming in the pool The cable can trip or entangle swimmers which could result in drowning A WARNING Risk of electrical shock or electrocution oe A Ground Fault Current Interrupter GFCI USA or a Residual Current Device RCD EUROPE must S be installed to protect your electric outlet and to prevent any possible electrical shock Failure to do so could create an electrical hazard which could result in death or serious injury to pool or spa users installers or others due to electrical shock and may also cause damage to property A CAUTION DO not switch the pool cleaner to ON if it is not fully immersed in water Operating the cleaner out of water will immediately cause severe damage and will result in loss of warranty Allow the cleaner to remain in the pool for 15 to 20 minutes following the end of its cleaning cycle This will allow the motors to cool adequately Do not leave the cleaner in the pool all the time Always remember to turn the power supply OFF and unplug it from the power outlet before removing the cleaner from the pool Prowler 720 and 730 Technical Data Reco
3. ASSY INCLUDES P N P12105 43 P12123 SHRINK TUBE 1 METER 0 44 P12124 SHRINK TUBE 1 METER 45 012125 BUTT CONNECTOR 46 SWIVEL 47 SOCKET Used on both of the Prowler 720 amp 730 models Prowler 720 and 730 Installation and User s Guide 14 Prowler 730 Model Prowler 720 and 730 Installation and User s Guide 15 Replacement Parts List for the Prowler 730 Model ITEM No PARTNo DESCRIPTION 1 P12100 4 PIN PLUG 0 2 P12126 CABLE ASSY INCLUDES P N s P12100 P12123 3 SEALING GROMMET 4 P12102 HANDLE ASSY 5 PUSH BUTTON LOCK 6 P12103 SPRING 9 7 CLEVIS PIN 8 R PIN FOR HANDLE 9 SCREW FOR PUMP 10 OUTLET TOP 11 SCREW OUTLET TOP 12 P12104 LOCK TAB 0 13 SCREW 14 P12105 NUT 15 P12106 SCREW O 16 P12107 SCREW O 17 RUBBER VALVE 18 P12108 SIDE PLATE 9 19 P12122 TRIM PANEL 20 P12109 BUSHING 21 SMALL ROLLER 22 P12133 SLEEVE ROLLER 23 P12110 PULLEY ASSY 24 P12111 DRIVE BELTS 9 25 P12112 DRIVE TRACK 0 26 P12127 DRIVE MOTOR MASTER INCLUDES P N P12123 21 P12129 DRIVE MOTOR SLAVE INCLUDES P N P12123 28 P12128 PUMP MOTOR INCLUDES P N P12123 29 PROPELLER 30 SCREW FOR PROPELLER 31 P12132 PVA BRUSH 32 P12131 WHEEL TUBE ASSY HEX 33 FLAT NYLON WASHER 34 P CLIP 35 P12118 FILTER BAG 0 36 BOTTOM LID ASSY 37 BOTTOM LID VALVE 38 P12120 FILTER SCREEN 39 P12134 POWER SUPPLY ASSY 1 HR 40 POWER SUPPLY COR
4. Prowler 720 and 730 provide on demand cleaning without running pumps It requires no installation no booster pump no hoses Just plug it in and place it in your pool it s a totally self contained cleaning and filtration system Two way cleaning with remote control convenience The Prowler 730 7 Remote Control provides the ultimate in automatic pool cleaning convenience The wireless radio remote control system provides two automatic cleaning options one for the pool bottom and a second for the bottom and sides Remote control functions allow you to override the automatic cleaning modes to perform quick spot clean ups Simply guide the cleaner to any area of the pool with the touch of a button No other cleaner is so simple No other cleaner provides such a complete cleaning job at such a low operating cost Prowler 720 Prowler 720 and 730 Installation and User s Guide General Features Two way cleaning performance e Powerful vacuum action removes fine particles and larger debris e Integrated filtration system captures dirt and debris in handy collection bag e Integrated filter reduces run time of your primary filtration system by 25 to save on pump energy use and normal wear and tear e Works fast thoroughly scrubs and vacuums pools up to 20 50 feet in just 60 90 minutes e Auto reverse feature prevents hang ups in corners and by steps and ladders for uninterrupted service e Cleans all pool surfaces g
5. Replacement Parts List cccccecccceececeeeeeseeteeeeteseeteseeneeeaneetaness 13 Prowler 730 Exploded VieW srgecscesacescascuamansansassebacos tucevevanccenunsdant eaesourmaraneenmiatimeseis 14 Prowler 730 Replacement Parts List cccccecceseececseeeeseeteneeteeeteneeseeeaneetaness 15 Prowler 720 and 730 Installation and User s Guide IMPORTANT SAFETY PRECAUTIONS Important Notice Attention Installer This guide contains important information about the installation operation and safe use of this product This information should be given to the owner and or operator of this equipment after installation of the pool cleaner Attention User This manual contains important information that will help you in operating and maintaining this pool cleaner Please retain it for future reference Consult Pentair Water with any questions regarding this equipment A WARNING Before installing this product read and follow all warning notices and instructions which are included Failure to follow safety warnings and instructions can result in severe injury death or property damage Call 800 831 7133 for additional free copies of these instructions Consumer Information and Safety The Prowler 720 and 730 pool cleaners are designed and manufactured to provide many years of safe and reliable service when installed operated and maintained according to the information in this manual Throughout the manual safety
6. Rev A 1 11 06 Contents IMPOMaNt Salety PVCCAULONS ences eimina irda oni dn AE G aE 1 1 610 Aaa Endaia 1 Prowler 720 and 730 Overview cccccssscccceececcenececceeueeesseaesecseaeeeeseausessaaneeesaas 1 Prowler 720 and 730 Features ccccccccseeeccceeeeeeeeeeeeeeeceeseeeeeeeessaeeeeeessaeeeeeeeeaas 2 2 instalation pcscsretccucers genasesteeeasansas EEEE 3 Cleaner COMPONE NS serisinin inene EE ENES Aa EAS Iaia 3 Operating the Prowler 720 and 730 Cleaner n nnannnannnnnnnnnnnnnnnnnennnnnnnnnnnnnnnennnne 4 0 E 4 5 Power SUDDIY acnee saewscanevadevenesiaundustsuusne ncaasuneenteseatyiedanuunl 6 Wireless Remote 6 eet ctuadshtocteeesevenetersengencncceedserseeints 7 Using the Radio Remote Control Feature cccccccccsececseeeeeececeeceseeeeseeesaneesaaess 7 Remote Control Cleaning Modes 0 7 Replacing the Remote Control Battery cc cecccceccceececeeeeeeeeeeeeeeseeeeseeeeaeeeeanees 8 Section 3 ennnen nnne 9 Changing Cleaning the Filter Bag 9 Changing the Drive BENS s sccseoccscnd cegidessveserererncdsvoressmesincsdeheseameonaunecstaressnesebanetesbed ene 10 BU NE O arie E E oer eo ee eee eee 10 ee ee eee 11 11 In Off Season Storage ccccccscccceccceeeeceececeeeecaeeeseeeeeeeseeeseueeseeeseessueeseueesseeesaees 11 Section 4 Replacement Parts 1 nnn 12 Prowler eai 12 Prowler 720
7. cleaner was not designed to automatically clean steps or to work under a solar cover It was also not designed to do initial cleanup for a new pool installation A CAUTION The unit must be supplied through a residual current device RCD having a rated operating current not exceeding 30mA e The connection to the branch circuit should be consistent with the local and National Electrical Code e Mishandling the unit can result in leakage of lubricants e f the supply cord is damaged it must be replaced by a licensed or certified electrician or a qualified pool serviceman in order to avoid hazards Prowler 720 and 730 Installation and User s Guide Section 1 Introduction The Prowler 720 and 730 Overview Vacuums what you can see filters what you can t Prowler 720 and 730 are the computer controlled programmed cleaners that scrub and vacuum your pool s bottom walls and steps and provides supplemental filtration of pool water Powerful efficient and smart The Prowler 720 and 730 features the patented Aqua Smart System This intelligent program enables the cleaner to fully cover and efficiently clean any standard residential swimming pool in approximately one hour 90 minutes for larger residential pools The high speed drive motor propels the unit across pool surfaces while a high efficiency pump motor delivers thorough economical cleaning performance Totally independent of your pool circulation system the
8. the rinse water is clear Ifnecessary machine wash the bag using only cold water with NO DETERGENT 5 Re install the bag on the support bars with the label in the center of one of the long sides of the bottom lid see Step 6 6 Re install the bottom lid assembly onto the body Push down on it until all 4 locking tabs snap properly into place Lock Tabs Figure 14 Prowler 720 and 730 Installation and User s Guide 10 Changing the Drive Belts Depending on usage the drive belts located behind the side plate will stretch When this happens in order to maintain the optimum performance of the unit these Figure 15 drive belts have to be changed 1 Turntherobotupside down and remove the bottom lid assembly as shown on page 9 Figure 14 Steps 1 4 2 Inside locate four screws on drive motor side which hold the side plate in place see Figure 15 3 Take out these four screws and remove the side plate see Figure 16 Figure 16 4 Remove the drive track Before removing the drive track notice how the drive belts are positioned for re assembly see Figure 17 5 Take out the old drive belts and replace them with new ones P N P12111 To re assemble reverse Steps 4 to 1 above Drive Track Changing Brushes Drive Belts a It is necessary to replace the brushes when they are worn out when the brushes reach the plastic of the wheel Worn out brushes will impede the cleaner s scrubbing climbing t
9. warnings and cautions are identified by the 44 symbol Be sure to read and comply with all of the warnings and cautions A DANGER Risk of electrical shock or electrocution 9 The electrical supply to this product must be installed in accordance with the National Electrical Code and all applicable local codes and ordinances Improper installation will create an electrical 5 hazard which could result in death or serious injury to pool or spa users installers or others due to electrical shock and may also cause damage to property Always disconnect the power to the cleaner before servicing Failure to do so could result in death or serious injury to serviceman pool users or others due to electrical shock Read and follow the specific instructions inside this guide A WARNING Hazardous suction Do not play with cleaner or cable or apply to body Can trap and tear hair or body parts Cable can trip or entangle swimmers which could result in drowning A WARNING Do not allow swimmers in the pool while pool cleaner is operating Cable can trip or entangle swimmers which could result in drowning A WARNING To reduce the risk of injury do not let children use or play with pool cleaner A CAUTION Before installing the cleaner in a gunite pool or a pool that is partially or completely tiled repair loose tiles and tighten any loose light rings A CAUTION Before installing the cleaner understand cleaner coverage The
10. D 41 P12130 BODY ASSY INCLUDES P N P12115 42 P12123 SHRINK TUBE 1 METER 43 SWIVEL 44 P12137 REMOTE CONTROL 45 P12138 AXLE FOR WHEEL TUBE ASSY 46 SOCKET Used on both of the Prowler 720 amp 730 models SAVE THESE INSTRUCTIONS Prowler 720 and 730 Installation and User s Guide 16 Notes Prowler 720 and 730 Installation and User s Guide 17 Notes Prowler 720 and 730 Installation and User s Guide 18 Notes Prowler 720 and 730 Installation and User s Guide Prowler 720 730 D Pentair Water Pool and Spa P N P12154 Rev A 1 11 06
11. ailure to comply will result in loss of warranty Prowler 720 and 730 Installation and User s Guide Replacing the Remote Control Battery Remove the top screw see Figure 13 Step 1 Pull the top of the cover away from the transmitter and then pull upwards Step 2 Replace the battery and make sure the polarity 15 the same as the existing battery Step 3 Push the cover downwards into the 2 slots Step 4 Push the top of the cover towards the battery until it snaps into place Step 5 NN Wn A WW N e Put the screw back into place 9V BATTERY PILE ALCALINE lt Figure 13 Prowler 720 and 730 Installation and User s Guide Section 3 Maintenance Maintaining the Prowler 720 and 730 Cleaner Clean the Filter Bag after every Cleaning Cycle 1 Unplug the power supply Keep the plug away from contact with water 2 Ifthe unitis inthe pool gently pull the cleaner toward you using the cable until the handle 1s within reach Use the handle not the cable to pull the cleaner out of the pool after allowing most of the water to drain from the unit 3 Lay the unit on its back on 8 smooth surface in order to prevent scratches on the machine body unlock and remove the bottom lid assembly see Figure 14 Steps 1 4 4 Remove the filter bag from the support bars see Step 5 turn it inside out and wash off all the dirt with a garden hose or ina sink Squeeze the bag gently until
12. direction after the button Left has been released LED Cleaning Modes Program The Remote Control has an advanced cleaning program with two options Option 1 STANDARD MODE this cycle 18 1 hours long and cleans the bottom of the pool only Option 2 SUPER MODE this cycle cleans the bottom and the walls of the swimming pools This cleaning program is 3 hours long and is registered in the cycle counter as two cycles one for each 1 5 hours of use Every time a cleaning cycle is complete the cleaner will stop automatically Every remote control unit is shipped from the factory with the Standard Mode as the primary program To switch from the Standard Mode to the Super Mode simply press the Program button once The cleaner will immediately receive the command and will start to clean the bottom and the walls Your signal that the cleaner is in the Special Mode is that the machine will climb up to the waterline in the first contact with a wall To return to the Standard Mode simply press the Program button again ONLY when the machine is on the pool bottom Figure 12 NOTE When the Power Supply is turned off the Mode is automatically returned to the Standard Mode floor cleaning only A CAUTION Be sure to always keep your Pentair pool cleaner properly stored anywhere between 50 to 104 Fahrenheit 10 to 40 Celsius This will keep the motors plastics and seals protected F
13. he walls and or general performance 1 Detach one of the side plates by unscrewing the four screws see Figure 15 Figure 18 2 With side plate detached take out the wheel tube from the machine 3 Remove the end hub and pull out the worn PVA brush see Figure18 4 Place the new PVA brush onto the hexagonal tube and replace the end hub Wheel Tube 5 Re install the wheel tube in place and reattach the side plate by screwing back in the four screws End Hub Prowler 720 and 730 Installation and User s Guide 11 Cable Care The cable may become twisted after a period of use To correct this condition simply lock the moveable handle on the top of the cleaner in the opposite diagonal direction The pool cleaner will now travel in the opposite direction while cleaning your pool and the cable will uncoil Check the cable periodically for external damage If the problem persists use the E Z Swivel device Place the Robot on the ground and unplug the cable from the transformer With one hand holding the E Z Swivel walk away from the Robot pulling the cable to its full length The core will rotate inside the cover which will untangle the cable see Figure 19 Important Maintenance Tips 1 Shut offand unplug the power supply every time you remove the cleaner from the water Clean the filter bag after every cycle Reverse the handle after every cleaning cycle to avoid tangling the cable Periodically straighte
14. mmended pool size 20 x 50 feet 6 1 15 2 meters Volume of water filtered 4 225 gal hr 16m hr Prowler 720 Floating cable length 60 feet Prowler 730 Floating cable length 19 feet Drive motor 24V DC high speed submersible Filter specification Reusable 2 micron Electrical specification 115V 60Hz Voltage in water 24V DC 24V DC high efficiency Pump motor submersible Handle Handle Lock Mechanism Side Plate Drive Track Scrubbing Brush Figure 1 Prowler 720 and 730 Installation and User s Guide Operating the Prowler 720 and 730 Cleaners cont d Figure 4 Handle Lock Mechanism Figure 5 TU LT BELEA 7 Figure 6 Prowler 720 and 730 Installation and User s Guide Place the power supply transformer at least ten feet three meters from the pool as shown in Figure 2 The transformer will supply low voltage to the cleaner Uncoil the cable as shown in Figure 3 For proper operation lock the moveable handle diagonally across the top of the cleaner s body Push down on the handle lock mechanism and slide the handle all the way to the end we recommend one slot before the end then release the lock The handle will remain fixed in this position Repeat this process on the other side of the cleaner Remember the handle must be fixed diagonally see Figures 4 and 5 Place the unit in the water Turn the unit side to side in the water to allow air to esca
15. n out the floating cable Replace worn brushes to ensure maximum cleaning performance oo ee S Make sure that your pool cleaner positions itself properly on the wall The machine handle must rest parallel to the water line upon reaching the surface of the water 7 Save your cleaner s packaging for off season storage or for shipping the unit to your dealer if service is required patent pending Figure 19 8 Store the unit and accessories on the caddy 9 Leave your pool cleaner in the water for 15 to 20 minutes after every cleaning cycle 10 Do not leave your cleaner in direct sunlight when not in use 11 Never leave the power supply in direct sunlight and avoid leaving it in the rain 12 Occasionally you should rinse your cleaner in clean fresh water This will lengthen the service life of the drive belts drive tracks and scrubbing brushes In Season Storage Do not leave your Prowler cleaner in the pool when not in use Doing so will reduce the life of your Filter Bag and the Prowler cleaner After removing the Prowler cleaner from the pool you should clean and re install the Filter Bag Then rest the Prowler cleaner on its side in a dry shaded area along with its Power Supply and properly coiled Floating Cable Off Season Storage When the Pool Season is over you should thoroughly clean the Filter Bag Make sure that there is no water in the Prowler cleaner Completely untangle and then pro
16. o the left to unlock it then pull it rey out Transformer 6 The Power Supply Cable Plug Rotate left and pull to unlock Transformer is now ready for operation Listed below are the Transformer buttons as shown in Figure 10 Figure 9 a Green Button push button turns the machine ON b Red Button push button turns the machine OFF IMPORTANT After every cycle the pool cleaner will turn off automatically In case you want to turn the machine off during the working cycle push the red button once and the indicator light will turn off signaling that the machine has stopped running Figure 10 Remember to keep the Power Supply at least 10 feet away from the pool Prowler 720 and 730 Installation and User s Guide Wireless Remote Control only for Prowler 730 cleaners equipped with Remote Control Using Radio Remote Control Feature and Accessing Cleaning Modes The Remote Control Model is equipped with a multi directional radio transmitter see Figure 12 This feature will enable you to guide the pool cleaner directly to areas of the pool requiring additional cleaning attention or for quick clean ups When you F d R press the Right or Left buttons the cleaner will turn until the button is released Then the cleaner will proceed straight ahead Right in the new direction Pressing the Forward Reverse button will cause the cleaner to proceed in the new
17. pe from the body and then let the cleaner sink to the bottom of the pool see Figure 6 Then spread the cable over the surface of the pool as evenly as possible as shown in Figure 2 Plug the cable into the power supply Make sure the key on the plug exactly corresponds with the key slot on the socket of the power supply see Figure 7 Plug the power supply into a grounded outlet Make sure that the electric outlet has been properly grounded see Figure 8 The light will glow indicating that the system is ON and the pool cleaner will start the cleaning cycle The unit keeps record of the number of cleaning cycles Only an authorized service center can display the accumulated cleaning cycles See details on the next page key key Transformer Transformer Plug Socket Figure 8 Figure 7 Setting Up the Standard Power Supply Transformer To plug the cable into the transformer socket on the power supply follow these steps 1 Prepare the plug with the key and three outside slots as shown in Figure 9 2 Fitthe key and the slots Transformer from cable plug exactly Socket with the corresponding key and slots from the Transformer transformer socket Socket 3 Push the plug all the way into the socket of the transformer 4 Once the plug is in rotate the plug to the right to lock it into place as shown in Figure 9 sep eens 5 To remove the plug first rotate the plug t
18. perly coil the Floating Cable Your Prowler cleaner and Power Supply should be stored in a dry protected area away from freezing temperatures Prowler 720 and 730 Installation and User s Guide Prowler 720 and 730 Installation and User s Guide Prowler 720 Model Replacement Parts Section 4 12 13 Replacement Parts List for the Prowler 720 Model ITEMNO PARTNO DESCRIPTION 1 012100 4PINPLUG 0 2 12101 CABLE ASSY INCLUDES P N P12100 P12125 3 SEALING GROMMET 4 012102 HANDLE ASSY 0 5 PUSH BUTTON LOCK 6 P12103 SPRING 0 7 CLEVIS PIN 8 R PIN FOR HANDLE 9 SCREW FOR PUMP 10 OUTLET TOP 11 SCREW OUTLET TOP 12 P1214104 LOCKTAB 0 13 SCREW 14 P12105 NUT 0 15 P12106 SCREW 0 16 P12107 SCREW 0 7 RUBBER VALVE 18 P12108 SIDEPLATE 0 19 12122 TRIM PANEL 0 20 P12109 BUSHING 0 21 SMALL ROLLER 22 12133 SLEEVE ROLLER 0 23 12110 PULLEY ASSY 0 24 NYLON BUSHING 25 P12111 DRIVE BELT 26 12112 DRIVE TRACK 0 7 12113 DRIVE MOTOR 1 HR INCLUDES P N 012125 4 28 12114 PUMP MOTOR INCLUDES P N P12123 29 PROPELLER 30 SCREW FOR PROPELLER 31 P12116 WHEEL TUBE ASSY HEX 32 12117 PVA BRUSH 33 LARGE ROLLER 34 P CLIP 35 012106 SCREW P CLIP 0 36 P12118 FILTER BAG 0 37 P12119 BOTTOM LID ASSY 38 BOTTOM LID VALVE 39 12120 FILTER SCREEN 0 40 12121 POWER SUPPLY ASSY 1 HR 41 POWER SUPPLY CORD 42 P12115 BODY
19. unite vinyl fiberglass and tile Additional Features Time and energy saving features e Reduces your filtration system s run time e Removes algae and bacteria e Vacuums all types of debris e Cleans and scrubs most pool steps e Built in filtration system with reusable filter bag e Cleans any size shape and type of standard residential pool in only one hour e The intelligent program enables the cleaner to fully cover and efficiently clean any standard residential swimming pool in approximately one hour 90 minutes for larger residential pools Prowler 720 and 730 Installation and User s Guide Section 2 Installation The following general information describes how to install the Prowler 720 and 730 robotic pool cleaners Carefully read the following so that you are fully aware of all the capabilities and features this Prowler cleaner has to offer NOTE Before installing this product read and follow all warning notices and instructions starting on page ii Introducing your new Prowler Cleaner Dear Customer Congratulations You have purchased one of the best pool cleaners that technology has to offer Thank you for choosing the Prowler cleaner to clean your pool We hope that you will enjoy using your new Prowler cleaner to maintain your swimming pool for years to come Your Prowler automatic pool cleaner includes the following e Cleaning Unit amp Cable e Power Supply Transformer e Caddy
Download Pdf Manuals
Related Search