Pelco DVR DX8100-EXP User's Manual
Contents
1. Slot 4 x1 PCI Express connectors DvD Rw 12 O Q Slot 7 Optional Expansion Unit 1 0 card C2636M B 4 07 9 Install the DX8100 1 0 Card The DX8100 1 0 card comes in a separate box that contains the DX8100 1 0 card and two cables a 5 pin alarm and relay cable and a 32 pin video input ribbon cable For information about the other DX8100 Expansion Unit kit components refer to Parts Liston page 4 The 1 0 card is installed in slot 7 and does not insert into a slot on the motherboard The DX8100 I O card receives power from the DX8100 and provides power for the DX8100 Expansion Unit Figure 8 DX8100 I O Card and Cables Table F describes the items included with the DX8100 1 0 card Table F DX8100 I O Card and Accessories Item Description TV Audio cable Video ribbon cable 32 pin 0X81001 0 card C2636M B 4 07 To install the DX8 1 Remove the 100 I O card in slot 7 Rear Cross Brace Refer to item 14 in Figure 7 on page 9 2 Dothe following a Remove the slot cover for slot 7 and retain the screw b Insert c Insert d Insert end of e nsert 3 This comple C2636M B 4 07 he DX8100 1 0 card into the slot 7 opening and secure the I O card bracket with the screw he 4 wire DX8100 power plug into the 1 0 card power connector CN302 he 5 pin Alarm and Relay cable into the DX8100 I O card Alarm and Rel2. Base Unit With Expansion Unit Camera inputs 8 24 16 32 Alarm inputs 8 24 16 32 ATM POS 8 24 16 32 Relay outputs 8 16 16 24 PARTS LIST In addition to this document Table B lists the components that are included in the DX8100 EXP Expansion Unit kit Oty Table B DX8100 Expansion Unit Kit Items Description Purpose DX8100 EXP Expansion Unit Provides connectivity for additional cameras alarms and relays Expansion cable Capture Card 16 channel Interconnects the DX8100 and Expansion Unit Adds 16 video channels provides connection for an optional 8 or 16 channel Audio card Interconnect flat ribbon cable 14 pin Interconnects the main Capture and secondary Capture cards DX8100 1 0 card Capture Card cable 5 pin Provides external interface between the Expansion Unit and DX8100 Alarm and relay cable that interconnects the DX8100 1 0 card and Capture Card Video input flat ribbon cable 32 pin Routes video input from DX8100 I O Card to the Capture Card Expansion Unit rack mount kit Includes two brackets and hardware to mount the Expansion Unit in a rack C2636M B 4 07 TOOLS NEEDED Table C DX8100 Expansion Unit Kit Items Oty Description 1 Phillips screwdriver 1 nonmagnetic 1 Properly grounded ESD wrist strap and mat 4 Small containers for storing screws optional OTHER DX8100 OPTIONAL ACCESSORIES The
3. 32 x 0 375 inch Phillips screw 4 Rack screw washers O 4 10 32 x 0 750 inch Phillips screw To install the Expansion Unit in an equipment rack 1 Attach the rack ears to the Expansion Unit using the eight 6 32 x 0 375 inch Phillips screws Refer to Figure 14 2 Using the remaining four 10 32 x 0 750 inch Phillips screws and rack screw washers install the Expansion Unit in the rack above the DX8100 C2636M B 4 07 15 To connect the Expansion Unit to the DX8100 DVR 1 Do one of the following Desktop mounting Set the Expansion to the side or on top of the DX8100 Rack mounting Attach the rack mount kit and install the Expansion Unit in the rack enclosure directly above the DX8100 2 Connect the 50 pin Expansion cable end partially shown in Figure 15 to the Expansion Unit connector and then connect the 50 pin Expansion cable end to DX8100 1 0 card 3 Plug the power cord back into the DX8100 and then into the wall Figure 15 Interfacing the Expansion Unit and DX8100 C2636M B 4 07 4 Power on the DX8100 Figure 16 Restarting the Unit 5 Log in to the DX8100 and verify that the additional devices are displayed in the DX8100 site tree For information about the additional features provided by the Expansion Unit refer to Table A on page 4 6 This completes the Expansion Unit installation process The DX8100 DVR does not have to be powered down to connect devices to the Expansion Unit To con
4. 00 EXP Expansion Unit familiarize yourself with the instructions throughout this manual The Expansion Unit is ready to use after you complete the installation steps in this manual The steps to install the Expansion Unit are summarized as follows 1 Unpack the DX8100 EXP Expansion Unit kit and check that you have all the necessary Expansion Unit kit components For information about components supplied in the DX8100 EXP Expansion Unit kit refer to Parts List on page 4 2 Verify that you have the required tools to install the Expansion Unit For information about the tools required to install the Expansion Unit refer to Tools Needed on page 5 3 Shut down the DX8100 Series DVR For information about shutting down the DX8100 refer to the DX8100 Installation Manual Operation Programming manual or DX8100 server online Help 4 Unplug the power cord from the wall socket WARNING It is critical that the unit be unplugged for your safety You must remove the power cord because current continues to flow through the DX8100 even when the unit is off Remove the power cord from the wall socket first and then from the rear of the DVR Figure 3 Removing Power Cord from Wall 5 Remove the power cord from the back of the DX8100 gt Figure 4 Removing Power Cord from DX8100 6 C2636M B 4 07 6 Ensure that the DX8100 Series DVR and all of its components are protected against electrostatic discharge ESD Before handling any el
5. DX8108 base unit comes with an 8 channel Capture Card and the DX8116 base unit includes a 16 channel Capture Card When considering adding the audio option The DX8108 AUD audio card is installed on the 8 channel Capture Card The DX8108 AUD audio card can be installed on a 16 channel Capture Card In this case only audio inputs 1 to 8 are available for recording Audio channels 9 to 16 can be configured but audio data is not recorded The DX8116 AUD audio card is installed on the 16 channel Capture Card The DX8116 AUD audio card cannot be installed on an 8 channel Capture Card The table below describes other DX8100 optional accessories that can be installed along with the Expansion Unit For a list of the current DX8100 options refer to the DX8100 Product Specification sheet Refer to the documentation supplied with the optional accessories for instructions on how to install those accessories Table D DX8100 Optional Accessories Option Number Description DX8108 AUD DX8100 8 channel audio input card DX8116 AUD DX8100 512RAM DX8100 16 channel audio input card DX8100 memory upgrade from 512 MB to 1 GB KBD300A KBD300A universal keyboard requires KBDKIT KBDKIT X VSI PRO Remote keyboard wiring kit X 220 VAC AVE video serial interfaces for ATM POS The VSI PRO and required cabling is available from AVE C2636M B 4 07 Getting Ready Before you install the DX81
6. PELLI DX8100 EXP Expansion Unit Installation Manual ii C2636M B 4 07 BYGAI Digital Video Recorder Introduction Welcome to the DX8100 EXP Expansion Unit upgrade for the DX8100 Series digital video recorder DVR This document serves as a guide for installing the DX8100 EXP Expansion Unit If you ordered the DX8124 or DX8132 model DVR the optional Capture Card and DX8100 1 0 card are already installed Use the Expansion cable to connect the Expansion Unit to the DX8100 For information about connecting the DX8100 Expansion Unit to the DX8100 DVR refer to Connecting the Expansion Unit to the DX8100 on page 15 This document is organized into the following sections Introduction on this page Getting Ready on page 6 Prepare DX8100 for Expansion Unit Installation on page 8 Install the DX8100 I O Card on page 10 Installing the Capture Card on page 12 Reassemble the Unit on page 14 Connecting the Expansion Unit to the DX8100 on page 15 The following figures show the front and back of the Expansion Unit 8100s X P222 ECCO Figure 1 DX8100 EXP Expansion Unit Front 9000000 30066 Figure 2 DX8100 EXP Expansion Unit Back C2636M B 4 07 Table A describes the additional capacity that the DX8100 EXP Expansion Unit upgrade adds to the base model DX8100 Table A DX8100 Expansion Unit Upgrade Features DX8108 Configuration DX8116 Configuration Feature Base Unit With Expansion Unit
7. adhesive side down on a free section of the inside of the door c Press down firmly to ensure that the label properly adheres to the inside of the door NOTE In the event that your unit or its components require service part labels must be present and appropriately affixed to the unit s door Pelco product support personnel use these labels to identify the exact components installed in your system A separate part label is required for each upgrade component installed on the DX8100 DX8100 512RAM 1 IU IT AKA 04070 FDF C6B6 10 J Figure 13 Example Product Label 3 Reinstall the unit in a rack enclosure if necessary and reconnect all of the cables and peripheral equipment you removed earlier 14 C2636M B 4 07 Connecting the Expansion Unit to the DX8100 This section describes how to connect the Expansion Unit to the DX8100 The Expansion Unit can be rack mounted positioned to the side or set on top of the DX8100 Figure 14 shows how to assemble the rack mount kit a X S120 seneca Figure 14 Assembling Expansion Unit Rack Mount Kit Table H describes the items included in the Expansion Unit rack mounting kit The Expansion Unit mounting dimensions are as follows Desktop 1 73 H x 17 W x 8 19 D inches 4 39 x 43 18 x 20 80 cm Rack Mount 1 73 H x 19 0 W x 8 19 D inches 4 39 x 48 26 x 20 80 cm Table H Expansion Unit Rack Mounting Kit Item Oty Description 1 2 Rack ears a 8 6
8. ay connector CN303 The other the cable inserts into the optional Capture Card For information about installing the optional Capture Card refer to Installing the Capture Card on page 12 he 32 pin ribbon cable into the video connector CN304 es installation of the DX8100 1 0 card Continue to nstalling the Capture Card on page 12 Figure 9 Installing the DX8100 I O Card Installing the Capture Card This section describes how to install the DX8100 Capture Card The Capture Card installation is performed after you have installed the DX8100 1 0 card The DX8100 Capture Card comes in a separate box that contains the Capture Card and one 14 pin interconnect cable For information about the other DX8100 Expansion Unit kit components refer to Parts List on page 4 The optional Capture Card is installed in PCI slot 3 and supports the additional 16 BNC video inputs 16 terminal block alarm inputs and 8 terminal block relay outputs provided by the Expansion Unit Figure 10 DX8100 Capture Card and Cable Table G describes the items included with the DX8100 Capture Card Table G DX8100 Optional Capture Card and Accessories Item Description 1 Optional Capture Card identical to the main Capture Card 0 14 pin ribbon cable C2636M B 4 07 To install the optional Capture Card 1 On the main Capture Card remove the 7 wire TV Audio cable and lay the cable over the DX8100 I O card Refer to callout 2
9. c in Figure 11 for the location of the TV Audio cable 2 Do the following a b C2636M B 4 07 Remove the slot cover for slot 3 and retain the screw Place the optional Capture Card under the 5 wire Alarm and Relay cable from the main Alarm and Relay 0 board and firmly seat the card in the PCI slot 3 connector and then secure the Capture Card bracket with the screw Connect the 7 wire TV Audio cable to the TV Audio connector on the optional and main Capture Card Verify that the 5 wire Alarm and Relay cable from the main Alarm and Relay I O board is firmly inserted in the 1 0 connector on the main Capture Card Connect the 5 wire Alarm and Relay cable from the DX8100 I O card to the 1 0 connector on the optional Capture Card Connect the 32 pin ribbon cable from the DX8100 1 0 card to the second video connector on the optional Capture Card Insert the 14 pin ribbon cable into the PB Path connectors on the optional and then main Capture Card This completes installation of the Capture Card Continue to Reassemble the Uniton page 14 Reassemble the Unit To reassemble the DX8100 1 Replace the chassis cover using the same screws you removed from the side and rear of the unit Refer to Figure 12 Figure 12 Replacing Chassis Cover 2 Attachthe silver part label that came in your upgrade kit to the inside of your DVR s front door a Remove the paper backing from the part label b Carefully place the label
10. ectronic components you should take steps to ground yourself properly so that any built up static electric charges are dissipated away from the unit The most effective method for combating ESD is to use a properly grounded wrist strap NOTE If you do not have access to a grounded wrist strap you can discharge any built up static by periodically touching an unpainted section of the chassis Figure 5 ESD Protection 7 Install the Expansion Unit PC cards and cabling 8 Connect the Expansion Unit to the DX8100 9 Start the DX8100 and verify that you have access to the additional features functions that are supported by the Expansion Unit C2636M B 4 07 Prepare DX8100 for Expansion Unit Installation This section describes how to access the DX8100 interior For information about mounting the DX8100 in a rack refer to the DX8100 Installation Manual OPEN THE DX8100 CHASSIS If the DX8100 is mounted in a rack it must be removed Two people might be required to lift and remove the DX8100 To move the DX8100 to an area that will provide full access to the unit chassis WARNING Make sure unit is turned off and you are wearing a properly grounded ESD wrist strap before attempting to open the DX8100 chassis cover For information about shutting down the unit refer to Getting Ready on page 6 1 Disconnect any cables or connections that may restrict access or interfere with the removal of the unit 2 If applicable Unscrew the fas
11. irective 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment PELLO Worldwide Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1 09001 Australia Canada Finland France Germany Italy Macau The Netherlands Russia Singapore South Africa Spain Sweden United Arab Emirates United Kingdom United States
12. nect devices to the Expansion Unit 1 Power down the Expansion Unit by disconnecting the 68 pin Expansion cable end at the Expansion Unit The Expansion Unit is powered down 2 Connect the additional devices to the Expansion Unit 3 Reconnect the 68 pin Expansion cable end to the Expansion Unit The Expansion Unit is powered up 4 Configure the DX8100 to work with the new devices attached to the Expansion Unit C2636M B 4 07 17 REVISION HISTORY Manual Date Comments C2636M 11 06 Original version C2636M A 3 07 Added Expansion Unit rack mount dimensions and revised DX8108 AUD DX8116 AUX text C2636M B 4 07 Corrected the reference to the Expansion cable from 68 to 50 pin Pelco the Pelco logo Camclosure Esprit ExSite Genex Legacy and Spectra are registered trademarks of Pelco Copyright 2007 Pelco AII rights reserved Endura and Spectra Ill are trademarks of Pelco DLP is a registered trademark of Texas Instruments Inc AVE is a registered trademark of AVE Inc 18 C2636M B 4 07 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below e Five years on fiber optic products and TW3000 Series unshielded twisted pair transmission products hree years on Spectra IV products hree years on Genex Series produc
13. or equal to the method by which he item was received by Pelco RETURNS n order to expedite parts returned to the factory for repair or credit please call he factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to Pelco 3500 Pelco Way Clovis CA 93612 5699 USA If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco c o Expeditors 473 Eccles Avenue South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 Green The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002 95 EC This equipment contains electrical or electronic components that must be recycled properly to comply with D
14. ornia Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or conse quential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem f there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explana ion with the product when returned Method of return shipment shall be the same
15. teners that are securing the unit in the rack and carefully lift the unit out of the rack 3 Place the DX8100 on a flat surface with ample workspace WARNING The chassis assembly includes parts with sharp edges To avoid injury use caution when working in and around the DX8100 s chassis and components 4 Using a Phillips screwdriver remove the chassis cover a Remove the top two screws on the left and right side panels of the DX8100 Refer to Figure 5 b Remove the four silver screws at top of the unit fastening the cover to the back of the unit Refer to Figure 6 c Carefully remove the chassis cover by sliding it back and up Set aside the cover Figure 6 Removing Chassis Cover 8 C2636M B 4 07 COMPONENT LAYOUT Figure 7 shows the slots and the DX8100 Series DVR s major components Some detail is removed from the illustrations in this manual for the purpose of clarity Slots on the motherboard are labeled differently Figure 7 DX8100 Interior Table E describes the DX8100 s slot assignments and major components Table E DX8100 Slot Assignments and Major Components Item Description Item Description Slot 1 PTZ card installed in PC connector CPU Slot 2 Capture Card installed in PCI connector Power supply Slot 3 PC connector DIMM sockets RAM Slot 5 x1 PCI Express connectors Hard drive bay Slot 6 x16 PCI Express connector Front cross brace Rear cross brace
16. ts multiplexers server and keyboard hree years on Camclosure and fixed camera models except the C3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and C3651H 2X camera models which have a five year warranty hree years on PMCL200 300 400 Series LCD monitors wo years on standard motorized or fixed focal length lenses wo years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products wo years on Spectra III Esprit ExSite and PS20 scanners including when used in continuous motion applications wo years on Esprit and WW5700 Series window wiper excluding wiper blades wo years except lamp and color wheel on Digital Light Processing DLP isplays The lamp and color wheel will be covered for a period of 90 days he air filter is not covered under warranty Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight pre paid to Pelco Clovis Calif
Download Pdf Manuals
Related Search