Pelco 100 Series User's Manual
Contents
1. See OFF Disables the DSS mode Ae A Mia le Digital slow shutter automatically adjusts the number of fields of integration depending on the light level of the viewed scene up to the maximum determined by the switch settings C2460M A 7 03 11 AGC AUTOMATIC GAIN CONTROL AGC automatically adjusts the image to compensate for changes in light levels ON Default setting Enables the AGC mode OFF Disables the AGC mode BLC BACK LIGHT COMPENSATION The BLC backlight compensation feature compensates for backlit scenes by enhancing objects in the center of the scene OFF Default setting Disables the BLC mode ON Enables the BLC mode Use this setting if a bright backlight is present and the subject in the center of the picture appears dark or as a silhouette VERTICAL PHASE ADJUSTMENT 24 VAC OPERATION ONLY When using more than one camera power supply a brief vertical roll may occur on the monitor when a camera view is switched To eliminate vertical roll reverse the 24 VAC connections on one camera If both cameras are connected to the same transformer this should solve the problem If reversing the connections does not solve the problem adjust the phase control by synchronizing or line locking the cameras to one another How to Adjust the Phase Control It may be necessary to have two people in communication when synchronizing the cameras one person at the camera and another p2. Copyright 2003 Pelco All rights reserved REVISION HISTORY Manual Date Comments C2460M 4 03 Preliminary manual for beta testing C2460M A 7 03 Final version C2460M A 7 03 15 PELCO World Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1509001 Orangeburg New York Las Vegas Nevada Eindhoven The Netherlands Wokingham United Kingdom Montreal Canada
3. 0 lux 50 IRE 30 fields of DSS f1 6 wide angle 2 6 6 0 mm or 4 0 9 0 mm varifocal D mount f1 6 Adjustable AC line lock internal auto select Electronic automatic 50 dB Selectable on off DIP switch selectable ON OFF DC drive 1 60 1 100 000 electronic auto Adjustable UL cUL and FCC Class B CE Class B UL cUL and FCC Class B Design and product specifications subject to change without notice C2460M A 7 03 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on Pelco manufactured cameras CC3500 CC3600 CC3700 and MC3500 MC3600 Series two years on all other cameras hree years on Genex Series multiplexers server and keyboard and 090 Series Camclosure Camera System wo years on 100 150 200 and 300 Series Camclosure Camera Systems wo years on all standard motorized or fixed focal length lenses wo years on Legacy CM6700 CM6800 CM6800E CM8500 CM9500 CM9740 CM9760 Matrix DF5 and DF8 Series Fixed Dome products wo years on Spectra Esprit and PS20 Scanners including when used in continuous motion applications wo years on Esprit and WW5700 series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders One year except video heads on video cassette recorde
4. INSTALLATION OPERATION 100 Series Camclosure Integrated Camera System With LowLight DSS Technology Dus LISTED 2460 7 03 CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS sssssssssetnettette teens 3 REGULATORY NOTIGES tne e rea ert enacted 3 WELCOME anaa 4 INSTALL THE BACK BOK rtr tdeo lr t enc t ea 5 REMOVE THE LOWER DOME INSTALE THE BACK BOX t etre o En EDI MB UN TEARS 5 ATTACH DIRECTLY TO A WALL CEILING sssssssssnee tnnt 5 ATTACH DIRECTLY TO CONCRETE WALL CEILING 6 ATTACH TO A 4S ELECTRICAL BOX iB MOUNT TO A PLASTER RING 2 7 CONNECT POWER WIRES cct cct ter ttem rh 8 INSTALL THE GAMERA MODUDE tte ttti 9 CHECK HEATER JUMPER INSTALL AND POSITIO MAKE CAMERA SETTINGS ZOOM FOCUS DIGITAL SLOW SHUTTER AGC AUTOMATIC GAIN CONTROL sssssseeeeeete tentent ntes BIG BACK LIGHT COMPENSATION cient etched VERTICAL PHASE ADJUSTMENT 24 VAC OPERATION ONLY HOW TO ADJUST THE PHASE VARIFOCAL LENS AUTO IRIS LEVEL ADJUSTMENT 00000 e eaaa eee aaa aane eaaa anana eaaa anaa aean REINSTALL THE LOWER DOME AND TRIM RING ssssseeee nennen 13 SPECIFICATIONS tanpa n
5. N Heater elements could be hot When camera power is on use caution when adjusting the camera REGULATORY NOTICES This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help C2460M A 7 03 3 Thank you for purchasing Pelco s Camclosure integrated camera system with LowLight DSS digital slow shutter technology Your new ICS100 Series surface mount dome system includes a high resolution low light color camera with auto i
6. aa DAN er tomm a bct 14 WARRANTY AND RETURN INFORMATION ssssseseetnette tentent ntes 15 LIST OF ILLUSTRATIONS Figure Page 1 Installation Directly to a Wall Ceiling seen 5 2 Installation Directly to a Concrete Wall Ceiling s 6 3 Installation on a 4S Electrical BOK in 6 4 Mounting to a Plaster Ring 5 Terminal Block for Input Power 6 Heater Jumper and Camera Connector Locations ssssssssssee 9 7 Default Switch Settings and Location of Camera Adjustments 11 8 Window Adjustment 0 c cccccssessscssessessesssessessscsssssscsscssccsessscssecsscsscssecsecsusaueassessessessecsucasecseenss 13 2 C2460M A 7 03 IMPORTANT SAFEGUARDS AND WARNINGS 1 Installation and servicing should be done only by qualified service personnel and conform to all local codes 2 Unless the unit is specifically marked as a NEMA Type 3 3R 35 4 4X 6 or 6P enclosure it is designed for indoor use only and must not be installed where exposed to rain and moisture 3 Useonly installation methods and materials capable of supporting four times the maximum specified load 4 Use stainless steel hardware to fasten the enclosure to outdoor surfaces 5 prevent damage from water leakage when installing an enclosure outdoors apply sealant around the bolt holes between the enclosure and mounting surface CAUTIO
7. e into position c Tighten the three Phillip screws to lock liner in place 2 Align the screw holes in the trim ring with those in the Camclosure base 3 Tighten the tamper resistant screws with the supplied 1 8 inch hollow screwdriver bit ADJUSTMENT GROOVE DOME LINER LOOSEN SCREWS Figure 8 Window Adjustment C2460M A 7 03 13 SPECIFICATIONS BACKBOX Electrical Input Voltage Power Consumption Video Connector General Operating Temperature Pan Tilt Adjustment Construction Finish Dimensions Above Ceiling Below Ceiling Bubble Environment Weight CAMERA Signal System Imaging Device Resolution Min Illumination Lens Synchronize Iris Control Signal to Noise AGG BLC Auto Iris Type Shutter Video Level CERTIFICATIONS NTSC Models PAL Models 12 VDC or 24 VAC 1096 auto sensing 13 watts or less BNC 50 to 122 F 46 to 50 C De ices to 25 F 4 C Manual 360 pan 180 tilt Aluminum with steel camera mounting bracket and polycarbonate dome White polyester powder coat 1 75 H x 3 50 W inches 4 45 x 8 89 cm 2 42 H x 5 48 W inches 6 15 x 13 90 cm 3 75 inch diameter Indoor outdoor 1 70 Ib 0 77 kg NTSC PAL 1 3 inch interline transfer CCD 480 TV lines 0 75 lux 40 IRE DSS off f1 6 wide angle 1 20 lux Q 50 IRE DSS off f1 6 wide angle 0 025 lux 40 IRE 30 fields of DSS f1 6 wide angle 0 04
8. ectly to a Wall Ceiling MOUNTING HARDWARE NOT SUPPLIED C2460M A 7 03 5 Attach Directly to Concrete Wall Ceiling Refer to Figure 2 for the following steps 1 Attach the base to the wall or ceiling hardware not supplied 2 Doone of the following Not Using Side Conduit Opening Verify the set screw and side conduit cover are tight Using Side Conduit Opening Loosen the set screw and remove the conduit plug Install a 3 4 inch 1 91 cm conduit fitting and tighten the set screw 3 Connect the video cable CII IY IIAL CONCRETE WALL OR CEILING BASE CONDUIT PLUG MOUNTING HARDWARE NOT SUPPLIED Figure 2 Installation Directly to a Concrete Wall Ceiling Attach to a 4S Electrical Box Refer to Figure 3 for the following steps The installation instructions assume that the 4S electrical box was previously installed 1 Attach the ICS100 AP adapter plate not supplied to the 4S box with the two 8 32 x 750 inch flat head screws supplied 2 Pull video and power wires into the base and attach the base to the adapter plate with the three 8 32 x 375 inch pan head screws supplied 3 Connect the video cable WALL OR CEILING 4S ELECTRICAL BOX QOO 8 32 X 750 FLAT D SCREW SUPPLIED ADAPTER PLATE BASE 8 32 X 375 PAN Heap SCREW SUPPLIED Figure 3 Installation on a 4S Electrical Box 6 C2460M A 7 03 Mount to a Plaster Ring R
9. efer to Figure 4 for the following steps Installation instructions assume that the 4S electrical box and plaster ring were previously installed 1 Pull video and power wires into the base 2 Attach the base to the plaster ring Use the two 8 32 x 750 inch pan head screws to attach the base to a 401 plaster ring Use the three 6 32 x 750 inch pan head screws to attach the base to a 404 plaster ring 3 Connect the video cable WALL OR C Q Pill 4S ELECTRICAL BOX 401 OR 404 PLASTER RING BASE SCREW SUPPLIED SEE TEXT FOR SIZE Figure 4 Mounting to a Plaster Ring C2460M A 7 03 CONNECT POWER WIRES Depending on the input voltage connect either the 12 VDC or 24 VAC input power wires to the terminal block inside the base Refer to Figure 5 for the location of the terminal block DC Operation Refer to the enlarged portion of Figure 5 for the 12 VDC and ground connections AC Operation It does not matter which terminals the power wires are connected to However if you are wiring more than one Camclosure system to the same transformer connect one side of the transformer to the same terminal on all units and connect the other side of the transformer to the remaining terminal Failure to connect all of the units the same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras Figure 5 Terminal Block for Inp
10. erson at the monitor to observe the vertical roll and the effect of any adjustments made at the camera To synchronize the cameras 1 Choose a reference camera to which all other cameras will be phased 2 Select a camera and synchronize it to the reference camera by turning the phase adjustment control refer to Figure 7 clockwise and or counterclockwise 3 Each time an adjustment is made switch back and forth between the camera you are adjusting and the reference camera Repeat this process as many times as necessary until the roll between the cameras is no longer noticeable 4 Adjustthe phase of all other cameras by repeating steps 2 through 3 Always adjust to the reference camera selected in step 1 NOTE The preferred method for camera phase adjustment is to use a dual trace oscilloscope to align the vertical synchronization pulses of the reference camera to the selected camera s VARIFOCAL LENS AUTO IRIS LEVEL ADJUSTMENT To adjust the auto iris level turn the level adjustment counterclockwise to decrease the brightness level and clockwise to increase the brightness level Refer to Figure 7 for the location of the level adjustment 12 C2460M A 7 03 REINSTALL THE LOWER DOME AND TRIM RING 1 Domes with Liners only Position the viewing window over the lens of the camera a Loosen the three Phillip screws located in the dome b Insert the blade of a standard screwdriver in one of the adjustment grooves Move dom
11. information Model and serial number 2 Date of shipment PO number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii If you are located outside the continental U S Alaska Hawaii Puerto Rico Puerto Rico Service Department Intermediate Consignee Ultimate Consignee Pelco American Overseas Air Freight Pelco 3500 Pelco Way 320 Beach Road 3500 Pelco Way Clovis CA 93612 5699 Burlingame CA 94010 Clovis CA 93612 5699 USA USA Pelco the Pelco logo Spectra Genex Esprit Camclosure and Legacy are registered trademarks of Pelco
12. ris and varifocal lens The LowLight color camera has extended DSS settings to enhance the low light performance of the camera by automatically adjusting the number of fields of integration This slows the picture frame rate and increases the camera s sensitivity in low light conditions Prior to installation and operation of your new system thoroughly familiarize yourself with the information in this manual 4 C2460M A 7 03 INSTALL THE BACK BOX REMOVE THE LOWER DOME Loosen the tamper resistant screws with the supplied 1 8 inch hollow screwdriver bit Remove the lower dome and place it to the side INSTALL THE BACK BOX IMPORTANT The installation methods for the ICS100 back box include the following To maximize tamper resistance e Attach Directly to a Wall Ceiling when not SET SCREW e Attach Directly to a Concrete Wall or Ceiling using the e Attach to a 4S Electrical Box side conduit e Mount to a Plaster Ring opening for wire connections verify that the conduit plug and set screw are tight Select the best method for your installation and then refer to the following pages for instructions Attach Directly to a Wall Ceiling Refer to Figure 1 for the following steps 1 Cuta small hole in the ceiling or wall and pull video and power wires into the base 2 Attach the back box to the wall ceiling hardware not supplied 3 Connect the video cable A n m OR BASE Figure 1 Installation Dir
13. rs VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent reight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise he above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state f a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following
14. ut Power 8 C2460M A 7 03 INSTALL THE CAMERA MODULE CHECK HEATER JUMPER The Camclosure is equipped with a heater to defrost the dome Some installations may not require this heater If the unit will never be subjected to a frost temperature you can disable the heater saving power requirements To disable the heater remove the jumper cover from the J1 jumper block refer to Figure 6 It is recommended that the jumper cover be left in the unit by installing it on one of the jumper pins CAMERA CONNECTOR J1 JUMPER Figure 6 Heater Jumper and Camera Connector Locations C2460M A 7 03 INSTALL AND POSITION THE CAMERA 1 2 4 Plug the video connector from the camera into the mating connector inside the back box refer to Figure 6 Position the camera so that the tab on the camera bracket is pointing out of the enclosure away from the ceiling or wall Refer to the following illustrations for proper camera orientation CAMERA BRACKET TAB ALWAYS POINTS OUT OF THE ENCLOSURE CAMERA BRACKET TAB ALWAYS POINTS OUT OF THE ENCLOSURE Wall Mounting The camera bracket Ceiling Mounting The camera bracket tab points out of the enclosure and the tab points out of the enclosure and the top top of the camera points up towards of the camera is pointed in the opposite the tab direction Install the camera bracket Gently squeeze the bracket place it against the shoulder inside the back box and gentl
15. y release Turn on power to the camera and monitor C2460M A 7 03 MAKE CAMERA SETTINGS CAUTION Heater elements could be hot When camera power is on use caution when adjusting the camera This applies to all models WHITE INDICATES SWITCH SETTING LEVEL PHASE ZOOM N lt q FOCUS wekan mp Figure 7 Default Switch Settings and Location of Camera Adjustments ZOOM FOCUS 1 Select a field of view by turning the zoom adjustment ring Refer to Figure 7 2 Tighten the zoom locking screw 3 Adjust the focus by moving the focus locking screw clockwise counterclockwise 4 Tighten the focus locking screw DIGITAL SLOW SHUTTER DSS Digital slow shutter slows the picture frame rate and increases the camera sensitivity under low light conditions Depending on the number of fields of integration the picture will develop a granular appearance and motion may show some lag resulting in a stereoscopic effect or streaking on fast moving objects These effects increase as the number of fields of integration increase Available settings include the following ON OFF DSS2 1 pss4 90 fields of integration maximum default setting 1 2 second scene update rate DSS2 pss4 16 fields of integration maximum 1 4 second scene update rate DSS2 pss1_ 4 fields of integration maximum 1 15 second scene update rate
Download Pdf Manuals
Related Search