Home
Pelco c3401m-a User's Manual
Contents
1. OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON SWITCH SETTING SW3 4 SW3 5 OFF OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF C3401M A 1 06 Table C Switch Settings for SW3 D Type Control Continued aan SWITCH SETTING ADDRESS SW3 2 SW3 3 SW3 4 SW3 5 SW3 6 SW3 7 SW3 8 71 ON OFF ON ON OFF OFF ON OFF 78 OFF ON ON ON OFF OFF ON OFF 79 ON ON ON ON OFF OFF ON OFF 80 OFF OFF OFF OFF ON OFF ON OFF 81 ON OFF OFF OFF ON OFF ON OFF 82 OFF ON OFF OFF ON OFF ON OFF 83 ON ON OFF OFF ON OFF ON OFF 84 OFF OFF ON OFF ON OFF ON OFF 85 ON OFF ON OFF ON OFF ON OFF 86 OFF ON ON OFF ON OFF ON OFF 87 ON ON ON OFF ON OFF ON OFF 88 OFF OFF OFF ON ON OFF ON OFF 89 ON OFF OFF ON ON OFF ON OFF 90 OFF ON OFF ON ON
2. 06 25 26 C3401M A 1 06 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below e Five years on FT FR8000 Series fiber optic products e Three years on Genex Series products multiplexers server and keyboard e Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra Esprit ExSite and PS20 scanners including when used in continuous motion applications Two years on Esprit and WW5700 Series window wiper excluding wiper blades Two years except lamp and color wheel on Digital Light Processing DLP displays The lamp and color wheel will be covered for a period of 90 days The air filter is not covered under warranty e Eighteen months on DX Series digital video recorders NVR300 Series network video recorders Endura Series distributed network based video products and TW3000 Series twisted pair transmission products e One year except video heads on video cassette recorders VCRs Video heads will be c
3. Note that you can connect video using either an unshielded twisted pair UTP of wires refer to Table D or coaxial cable refer to Table E A BNC connector for coaxial cable is attached to the dome drive If you are wiring more than one dome drive to the same transformer connect one side of the transformer to pin 9 of the RJ45 10 connector on all modules Connect the other side of the transformer to pin 10 of the RJ45 10 connector on all modules Failure to connect all modules the same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras b Turn the surface ring upside down and place it on the inside of the ceiling tile Refer to Figure 8 Dn WARNING Do not over tighten the mounting hardware Doing so can impede the pan movement of the dome drive c Attach the dome drive to the ceiling tile and surface mount ring with the two 10 x 1 50 inch self tapping screws supplied Refer to Figure 8 d Replace the ceiling tile DOME DRIVE SURFACE MOUNT RING Figure 7 How to Remove Surface Mount Ring 20 C3401M A 1 06 in SURFACE MOUNT RING CEILING TILE i lt t DOME DRIVE lt 10x 1 50 INCH SELF TAPPING SCREWS SUPPLIED Figure 8 Ceiling Tile Installation 6 Line up the tabs on the trim ring with the slots in the dome drive Snap the trim ring and dome bubble into place C3401M A 1 06 21 22 HARD CEILING
4. OFF ON OFF 91 ON ON OFF ON ON OFF ON OFF 92 OFF OFF ON ON ON OFF ON OFF 93 ON OFF ON ON ON OFF ON OFF 94 OFF ON ON ON ON OFF ON OFF 95 ON ON ON ON ON OFF ON OFF 96 OFF OFF OFF OFF OFF ON ON OFF 97 ON OFF OFF OFF OFF ON ON OFF 98 OFF ON OFF OFF OFF ON ON OFF 99 ON ON OFF OFF OFF ON ON OFF 100 OFF OFF ON OFF OFF ON ON OFF 101 ON OFF ON OFF OFF ON ON OFF 102 OFF ON ON OFF OFF ON ON OFF 103 ON ON ON OFF OFF ON ON OFF 104 OFF OFF OFF ON OFF ON ON OFF 105 ON OFF OFF ON OFF ON ON OFF 106 OFF ON OFF ON OFF ON ON OFF 107 ON ON OFF ON OFF ON ON OFF 108 OFF OFF ON ON OFF ON ON OFF 109 ON OFF ON ON OFF ON ON OFF 110 OFF ON ON ON OFF ON ON OFF 111 ON ON ON ON OFF ON ON OFF 112 OFF OFF OFF OFF ON ON ON OFF 113 ON OFF OFF OFF ON ON ON OFF 114 OFF ON OFF OFF ON ON ON OFF C3401M A 1 06 11 12 SPECTRA ADDRESS 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 Table C Switch Settings for SW3 D Type Control Continued ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF SW3 2 ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF SW3 3 OFF
5. 1 On top of the dome drive is an opening for an optional translator board The opening has a cover that must be left in place if a translator board is not required A taller cover is supplied if a translator board is installed If you are going to install a translator board follow the instructions that come with the translator board If you are not going to install a translator board save the taller cover in case a translator board is ever installed Using the supplied template cut holes in the ceiling for the dome drive and mounting hardware Pull the wiring for power video and control through the ceiling Remove the surface mount ring from the dome drive as follows Refer to Figure 7 a _ Place fingers on the circular marks located on the sides of the surface mount ring b Pinch the sides c Lift and remove the surface mount ring from the dome drive Connect the wiring You can plug the male RJ45 10 connector also known as an RJ 50 connector on the supplied interface cable refer to Figure 6 into the mating connector on top of the dome drive and then connect your wiring to the other end of the cable Or You can connect the supplied RJ45 10 connector to your wiring and then plug the connector into the dome drive Refer to Figure 6 Table D Table E and Table F for wiring connections Note that you can connect video using either an unshielded twisted pair UTP of wires refer to Table D or coaxial cable refer to Table E A B
6. 236 OFF OFF ON ON OFF ON ON ON 237 ON OFF ON ON OFF ON ON ON 238 OFF ON ON ON OFF ON ON ON 239 ON ON ON ON OFF ON ON ON 240 OFF OFF OFF OFF ON ON ON ON 241 ON OFF OFF OFF ON ON ON ON 242 OFF ON OFF OFF ON ON ON ON 243 ON ON OFF OFF ON ON ON ON 244 OFF OFF ON OFF ON ON ON ON 245 ON OFF ON OFF ON ON ON ON 246 OFF ON ON OFF ON ON ON ON 247 ON ON ON OFF ON ON ON ON 248 OFF OFF OFF ON ON ON ON ON 249 ON OFF OFF ON ON ON ON ON 250 OFF ON OFF ON ON ON ON ON 251 ON ON OFF ON ON ON ON ON 252 OFF OFF ON ON ON ON ON ON 253 ON OFF ON ON ON ON ON ON 254 OFF ON ON ON ON ON ON ON C3401M A 1 06 15 SURFACE MOUNT INSTALLATION 1 On top of the dome drive is an opening for an optional translator board The opening has a cover that must be left in place if a translator board is not required A taller cover is supplied if a translator board is installed If you are going to install a translator board follow the instructions that come with the translator board If you are not going to install a translator board save the taller cover in case a translator board is ever installed Prepare the ceiling as follows a Using the supplied template drill holes for toggle bolts or studs Refer to Figure 3 or Figure 4 b Dome with translator board Punch out the pie shaped section from the supplied templates Using the pie shaped template either cut a hole through the ceiling or make a hole with a depth of 0 25 inches 6 mm c Drill a ho
7. F OFF ON ON OFF OFF ON ON OFF SW3 3 ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON SWITCH SETTING SW3 4 SW3 5 ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF SW3 6 ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON SW3 7 OFF ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON SW3 8 ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON C3401M A 1 06 Table C Switch Settings for SW3 D Type Control Continued aan SWITCH SETTING ADDRESS SW3 2 SW3 3 SW3 4 SW3 5 SW3 6 SW3 7 SW3 8 229 ON OFF ON OFF OFF ON ON ON 230 OFF ON ON OFF OFF ON ON ON 231 ON ON ON OFF OFF ON ON ON 232 OFF OFF OFF ON OFF ON ON ON 233 ON OFF OFF ON OFF ON ON ON 234 OFF ON OFF ON OFF ON ON ON 235 ON ON OFF ON OFF ON ON ON
8. F OFF 16 OFF OFF OFF OFF ON OFF OFF OFF 17 ON OFF OFF OFF ON OFF OFF OFF 18 OFF ON OFF OFF ON OFF OFF OFF 19 ON ON OFF OFF ON OFF OFF OFF 20 OFF OFF ON OFF ON OFF OFF OFF 21 ON OFF ON OFF ON OFF OFF OFF 2 OFF ON ON OFF ON OFF OFF OFF 23 ON ON ON OFF ON OFF OFF OFF 24 OFF OFF OFF ON ON OFF OFF OFF 25 ON OFF OFF ON ON OFF OFF OFF 26 OFF ON OFF ON ON OFF OFF OFF 2 ON ON OFF ON ON OFF OFF OFF 28 OFF OFF ON ON ON OFF OFF OFF 29 ON OFF ON ON ON OFF OFF OFF 30 OFF ON ON ON ON OFF OFF OFF 31 ON ON ON ON ON OFF OFF OFF 32 OFF OFF OFF OFF OFF ON OFF OFF 33 ON OFF OFF OFF OFF ON OFF OFF 34 OFF ON OFF OFF OFF ON OFF OFF 35 ON ON OFF OFF OFF ON OFF OFF 36 OFF OFF ON OFF OFF ON OFF OFF 37 ON OFF ON OFF OFF ON OFF OFF 38 OFF ON ON OFF OFF ON OFF OFF C3401M A 1 06 10 SPECTRA ADDRESS Table C Switch Settings for SW3 D Type Control Continued SW3 2 SW3 3 SW3 6 SW3 7 SW3 8 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 n 72 73 74 75 76 ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF ON OFF OFF OFF OFF ON ON ON ON OFF
9. F ON 165 ON OFF ON OFF OFF ON OFF ON 166 OFF ON ON OFF OFF ON OFF ON 167 ON ON ON OFF OFF ON OFF ON 168 OFF OFF OFF ON OFF ON OFF ON 169 ON OFF OFF ON OFF ON OFF ON 170 OFF ON OFF ON OFF ON OFF ON 171 ON ON OFF ON OFF ON OFF ON 172 OFF OFF ON ON OFF ON OFF ON 173 ON OFF ON ON OFF ON OFF ON 174 OFF ON ON ON OFF ON OFF ON 175 ON ON ON ON OFF ON OFF ON 176 OFF OFF OFF OFF ON ON OFF ON 177 ON OFF OFF OFF ON ON OFF ON 178 OFF ON OFF OFF ON ON OFF ON 179 ON ON OFF OFF ON ON OFF ON 180 OFF OFF ON OFF ON ON OFF ON 181 ON OFF ON OFF ON ON OFF ON 182 OFF ON ON OFF ON ON OFF ON 183 ON ON ON OFF ON ON OFF ON 184 OFF OFF OFF ON ON ON OFF ON 185 ON OFF OFF ON ON ON OFF ON 186 OFF ON OFF ON ON ON OFF ON 187 ON ON OFF ON ON ON OFF ON 188 OFF OFF ON ON ON ON OFF ON 189 ON OFF ON ON ON ON OFF ON 190 OFF ON ON ON ON ON OFF ON C3401M A 1 06 13 14 SPECTRA ADDRESS 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 Table C Switch Settings for SW3 D Type Control Continued ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF SW3 2 ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OF
10. INSTALLATION Spectra Mini Dome Indoor Ceiling Mount C3401M A 1 06 Important Safety Instructions a 16 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Installation should be done only by qualified personnel and conform to all local codes Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is designed for indoor use only and it must not be installed where exposed to rain and moisture Use only installation methods and materials capable of supporting four times the maximum spec
11. NC connector for coaxial cable is attached to the dome drive If you are wiring more than one dome drive to the same transformer connect one side of the transformer to pin 9 of the RJ45 10 connector on all modules Connect the other side of the transformer to pin 10 of the RJ45 10 connector on all modules Failure to connect all modules the same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras C3401M A 1 06 A WARNING Do not over tighten the mounting hardware Doing so can impede the pan movement of the dome drive 5 Attach the dome drive to the ceiling with the two 3 16 toggle bolts not supplied Refer to Figure 9 DOME DRIVE CEILING 3 16 TOGGLE BOLTS NOT SUPPLIED O Figure 9 In Ceiling Installation to a Fixed Ceiling 6 Line up the tabs on the trim ring with the slots in the dome drive Snap the trim ring and bubble into place C3401M A 1 06 23 Specifications MECHANICAL Pan Movement Vertical Tilt Manual Pan Tilt Speeds Pan Tilt Preset Speeds Pan Tilt ELECTRICAL Input Voltage Input Power Fuse GENERAL Construction Top Cap Trim Ring and Surface Mount Ring Bubble Finish Light Attenuation Smoked Clear Cable Entry Environment Weight CAMERA Signal Format Scanning System Image Sensor Effective Pixels NTSC PAL 360 continuous pan rotation Unobstructed 2 to 92 0 4 80
12. ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF SWITCH SETTING SW3 4 SW3 5 OFF ON OFF ON OFF ON OFF ON OFF ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON ON ON SW3 6 ON ON ON ON ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF SW3 7 ON ON ON ON ON ON ON SW3 8 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON C3401M A 1 06 Table C Switch Settings for SW3 D Type Control Continued aan SWITCH SETTING ADDRESS SW3 2 SW3 3 SW3 4 SW3 5 SW3 6 SW3 7 SW3 8 153 ON OFF OFF ON ON OFF OFF ON 154 OFF ON OFF ON ON OFF OFF ON 155 ON ON OFF ON ON OFF OFF ON 156 OFF OFF ON ON ON OFF OFF ON 157 ON OFF ON ON ON OFF OFF ON 158 OFF ON ON ON ON OFF OFF ON 159 ON ON ON ON ON OFF OFF ON 160 OFF OFF OFF OFF OFF ON OFF ON 161 ON OFF OFF OFF OFF ON OFF ON 162 OFF ON OFF OFF OFF ON OFF ON 163 ON ON OFF OFF OFF ON OFF ON 164 OFF OFF ON OFF OFF ON OF
13. The dome can be mounted to the surface of ceilings or it can be recessed in hard ceilings or standard 2 x 2 ft 61 x 61 cm tiles in suspended ceilings The Spectra Mini includes a high resolution color camera video output capability through either coaxial cable or UTP wiring pan tilt control using D P or Coaxitron protocol and on screen programming A translator board can be installed on the dome for communication with non Pelco controllers The dome is compatible with the following translator boards TXB AD Translator board for American Dynamics controllers TXB B Translator board for Philips Burle controllers TXB S422 Translator board for Sensormatic controllers TXB V Translator board for Vicon controllers MODELS SD4 W0 Indoor dome system smoked bubble NTSC SD4 W1 Indoor dome system clear bubble NTSC SD4 W0 X Indoor dome system smoked bubble PAL SD4 W1 X Indoor dome system clear bubble PAL C3401M A 1 06 Installation The following parts are supplied with the Spectra Mini dome system NN S So os ao Dome drive Dome bubble with trim ring Interface cable with a male RJ45 10 connector on one end and four twisted wire pairs on the other end Cover for use with optional translator board 10 x 1 50 inch self tapping screws for suspended ceiling installation 8 x 3 50 inch self tapping screws for surface mount installation Installation manual Operation Programming manual Template The following parts in a
14. age 18 16 14 12 1 0 mm 1 5 mm 2 5 mm 3 5 mm 215 ft 341 ft 542 ft 863 ft ZAVAC gz inl 154 m 245 m 391 m NOTE Power consumption is 21 VA per unit Use a power source with a minimum of 21 VA per unit C3401M A 1 06 RECESSED INSTALLATION SUSPENDED CEILING f C3401M A 1 06 On top of the dome drive is an opening for an optional translator board The opening has a cover that must be left in place if a translator board is not required A taller cover is supplied if a translator board is installed If you are going to install a translator board follow the instructions that come with the translator board If you are not going to install a translator board save the taller cover in case a translator board is ever installed Remove the ceiling tile from the ceiling Using the supplied template cut holes in the ceiling tile for the dome drive and mounting hardware Remove the surface mount ring from the dome drive as follows Refer to Figure 7 a _ Place fingers on the circular marks located on the sides of the surface mount ring b Pinch the sides c Lift and remove the surface mount ring from the dome drive Do not discard the surface mount ring because it is required to complete the installation Connect the wiring and attach the dome drive to the ceiling tile Using the supplied interface cable a _ Plug the male RJ45 10 connector also known as an RJ 50 connector on the supplied int
15. al number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem f there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned ethod of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS n order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below f you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco Pelco c o Expeditors 3500 Pelco Way 473 Eccles Avenue Clo
16. ddition to normal installation tools are needed but not supplied Small flashlight for viewing switches Long handled flat blade screwdriver for setting switches 6 32 toggle bolts for surface mount installation 8 32 studs and nuts for surface mount installation to concrete 3 16 toggle bolts for recessed installation in hard ceiling DOME DRIVE TRIM RING AND TRANSLATOR BOARD BUBBLE COVER INTERFACE CABLE 1 5 INCH SELF TAPPING MANUALS AND RJ45 10 SCREWS 2 EA CONNECTOR 3 5 INCH SELF TAPPING SCREWS 2 EA Figure 1 Package Components C3401M A 1 06 SWITCH SETTINGS Coaxitron control If you are going to use Coaxitron protocol to communicate with the dome system you do not have to set any switches Proceed to the installation instructions that follow this section Non Pelco control If you are going to install a protocol translator board to communicate with the dome system through anon Pelco controller proceed to the installation instructions that follow this section When you are instructed to install the translator board you will set the switches as described in the installation operation manual that accompanies the translator board D or P control If you are going to use D or P protocol to communicate with the dome system follow the steps below to set the switches Refer to Figure 2 WARNING Do not remove the dome liner refer to Figure 2 Replacing the dome liner requires qualified service personnel otherwise the do
17. e in a residential instal lation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accor dance with the instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e _ Reorient or relocate the receiving antenna e _ Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help You may also find helpful the following booklet prepared by the FCC How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission s rules This Class B digital apparatus complies with Canadian ICES 003 4 C3401M A 1 06 Description The Spectra Mini is an indoor dome system designed for ceiling applications
18. erface cable refer to Figure 6 into the mating connector on top of the dome drive b Turn the surface ring upside down and place it on the inside of the ceiling tile Refer to Figure 8 A WARNING Do not over tighten the mounting hardware Doing so can impede the pan movement of the dome drive c Attach the dome drive to the ceiling tile and surface mount ring with the two 10 x 1 50 inch self tapping screws supplied Refer to Figure 8 d Replace the ceiling tile e Remove an adjacent ceiling tile and connect your wiring to the dome drive Refer to Figure 6 Table D Table E and Table F for wiring connections Note that you can connect video using either an unshielded twisted pair UTP of wires refer to Table D or coaxial cable refer to Table E A BNC connector for coaxial cable is attached to the dome drive If you are wiring more than one dome drive to the same transformer connect one side of the transformer to pin 9 of the RJ45 10 connector on all modules Connect the other side of the transformer to pin 10 of the RJ45 10 connector on all modules Failure to connect all modules the same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras Using the supplied RJ45 10 connector a Connect the supplied RJ45 10 connector to your wiring and then plug the connector into the dome drive Refer to Figure 6 Table D Table E and Table F for wiring connections
19. est from the controller Table B Switch Settings for SW3 P Type Control SEA SWITCH SETTING SE SWITCH SETTING ADDRESS Sw3 1 SW3 2 SW3 3 SW3 4 SW3 5 ADDRESS sw31 sw3 2 SW3 3 SW3 4 SW3 5 1 2 ON OFF OFF OFF OFF 18 ON OFF OFF OFF ON 3 OFF ON OFF OFF OFF 19 OFF ON OFF OFF ON 4 ON ON OFF OFF OFF 20 ON ON OFF OFF ON 5 OFF OFF ON OFF OFF 21 OFF OFF ON OFF ON 6 ON OFF ON OFF OFF 22 ON OFF ON OFF ON 7 OFF ON ON OFF OFF 23 OFF ON ON OFF ON 8 ON ON ON OFF OFF 24 ON ON ON OFF ON 9 OFF OFF OFF ON OFF 25 OFF OFF OFF ON ON 10 ON OFF OFF ON OFF 26 ON OFF OFF ON ON 11 OFF ON OFF ON OFF 27 OFF ON OFF ON ON 12 ON ON OFF ON OFF 28 ON ON OFF ON ON 13 OFF OFF ON ON OFF 29 OFF OFF ON ON ON 14 ON OFF ON ON OFF 30 ON OFF ON ON ON 15 OFF ON ON ON OFF 31 OFF ON ON ON ON 16 ON ON ON ON OFF 32 ON ON ON ON ON 8 C3401M A 1 06 Table C Switch Settings for SW3 D Type Control SPECTRA SWITCH SETTING ADDRESS SW3 3 SW3 4 SW3 5 SW3 6 SW3 7 SW3 8 1 ON OFF OFF OFF OFF OFF OFF OFF a OFF ON OFF OFF OFF OFF OFF OFF 3 ON ON OFF OFF OFF OFF OFF OFF 4 OFF OFF ON OFF OFF OFF OFF OFF 5 ON OFF ON OFF OFF OFF OFF OFF 6 OFF ON ON OFF OFF OFF OFF OFF 7 ON ON ON OFF OFF OFF OFF OFF 8 OFF OFF OFF ON OFF OFF OFF OFF 9 ON OFF OFF ON OFF OFF OFF OFF 10 OFF ON OFF ON OFF OFF OFF OFF 1 ON ON OFF ON OFF OFF OFF OFF 12 OFF OFF ON ON OFF OFF OFF OFF 13 ON OFF ON ON OFF OFF OFF OFF 14 OFF ON ON ON OFF OFF OFF OFF 15 ON ON ON ON OFF OFF OF
20. ified load Use stainless steel hardware to fasten the mount to outdoor surfaces To prevent damage from water leakage when installing a mount outdoors on a roof or wall apply sealant around the bolt holes between the mount and mounting surface CAUTION These servicing instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other that contained in the operating instructions unless you are qualified to do so Only use replacement parts recommended by Pelco The product and or manual may bear the following marks A This symbol indicates that dangerous voltage constituting a risk of electric shock is A This symbol indicates that there are important operating and maintenance instructions C3401M A 1 06 present within this unit CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN in the literature accompanying this unit Regulatory Notices This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interferenc
21. le in the ceiling for wiring Note that you do not have to run wiring through the ceiling you can fasten the wires to the ceiling and then run the wires through the air gap between the ceiling and the surface mount ring as shown in Figure 5 Connect the wiring and attach the dome drive to the ceiling You can plug the male RJ45 10 connector also known as an RJ 50 connector on the supplied interface cable refer to Figure 6 into the mating connector on top of the dome drive and then connect your wiring to the other end of the cable Or You can connect the supplied RJ45 10 connector to your wiring and then plug the connector into the dome drive WARNING Do not over tighten the mounting hardware Doing so can impede the pan movement of the dome drive Refer to Figure 3 and Figure 4 for installing the dome drive Refer to Figure 6 Table D Table E and Table F for wiring connections Note that you can connect video using either an unshielded twisted pair UTP of wires refer to Table D or coaxial cable refer to Table E A BNC connector for coaxial cable is attached to the dome drive If you are wiring more than one dome drive to the same transformer connect one side of the transformer to pin 9 of the RJ45 10 connector on all modules Connect the other side of the transformer to pin 10 of the RJ45 10 connector on all modules Failure to connect all modules the same way will cause the cameras to be out of phase with each other and may pr
22. me drive may not operate properly 1 Place the dome drive on a flat surface with the dome liner pointing up 2 Point the camera straight up 3 Using a flashlight look straight down through the viewing slot of the dome liner Look at the circuit board in the bottom of the housing Rotate the dome liner until you see two DIP switches on the circuit board 4 Set the switches Refer to Table A Table B and Table C There are no settings for SW1 NOTE The unit automatically detects D or P protocal DATA PORT Figure 2 Component Locations DATA PORT The data port refer to Figure 2 allows access for on site setup and testing of the dome system It also is used for uploading revised operating software and language files Refer to Software Language File Upload in the Operation Programming manual C3401M A 1 06 7 Table A Switch Settings for SW2 Special Systems Switch Number AD 32 Preset System CM9502 Setting Baud Rate Switch Number 2400 Baud 4800 Baud 9600 Baud Protocol Termination Switch Number Terminated SW2 1 SW2 2 SW2 3 SW2 4 SW2 5 SW2 6 SW2 7 SW2 8 SW2 9 ON OFF ON SW2 3 SW2 4 SW2 5 SW2 6 SW2 7 SW2 8 SW2 9 ON OFF Not Terminated If you are connecting a single dome to a controller terminate the dome When connecting more than one dome to a single controller terminate the dome farth
23. oduce a vertical roll when switching between cameras 4 Line up the tabs on the trim ring with the slots in the dome drive Snap the trim ring and bubble into place C3401M A 1 06 CONCRETE i CEILING CEILING Ll IT VI 6 32 TOGGLE BOLTS NOT SUPPLIED OR 8 32 MOUNTING HARDWARE 8 X 3 5 INCH SELF TAPPING NOT SUPPLIED SCREWS F E SUPPLIED Noe D DRIVE Figure 3 Ceiling Installation Figure 4 Concrete Ceiling Installation mj eee CONNECTOR TWISTED PAIRS a Figure 5 Wiring Attached to Ceiling Figure 6 Interface Cable C3401M A 1 06 17 Table D Interface Cable Wiring Table E Video Coaxial Cable Requirements Pin Color Function Cable Type Maximum Distance 1 ORANGE UTP RG59 U 750 ft 229 m 2 WHITE ORANGE UTP RG6 U 1 000 ft 305 m 3 GREEN RX RG11 U 1 500 ft 457 m 2 11 ITE GREEN om Cable requirements gt BLUE TX 75 ohm impedance 6 WHITE BLUE TX All copper center conductor 7 NOTUSED All copper braided shield with 95 braid coverage 8 NOT USED 9 BROWN 24 V Av 10 WHITE BROWN 24V N Table F Wiring Distances The following are the recommended maximum distances for 24 VAC applications and are calculated with a 10 percent voltage drop Ten percent is generally the maximum allowable voltage drop for AC powered devices Wire Gauge Volt
24. overed for a period of six months e Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and seri
25. sec manual operation 100 sec turbo 0 7 40 sec manual operation 140 sec 80 sec For variable speed operation an appropriate controller is required 18 30 VAC 24 VAC nominal 21 VA nominal 1 6A Anodized cast aluminum ABS plastic Acrylic White 1 2 F stop light loss Zero light loss Single RJ45 10 connector pigtail supplied BNC connector Indoor 1 75 Ib 0 79 kg NTSC PAL 2 1 interlace 1 4 inch interline CCD 768 H x 494 V 752 H x 582 V C3401M A 1 06 Horizontal Resolution NTSC PAL Minimum Illumination Sync System White Balance Shutter Speed Gain Control Video Output Video Signal to Noise Ratio LENS Lens Zoom Speed optical range Horizontal Angle of View Focus Iris Control gt 470 TV lines gt 460 TV lines 3 0 lux AC line lock phase adjustable via remote control V Sync Automatic with manual override Automatic electronic iris manual 1 60 1 30 000 Automatic with manual override 1 0 to 1 2 Vp p 75 ohms adjustable gt 50 dB F1 8 F 4 2 42 mm optical 10X optical zoom 8X digital zoom 1 5 2 5 4 3 seconds 46 4 wide zoom 5 0 telephoto zoom Automatic with manual override Automatic with manual override Design and product specifications subject to change without notice WITH TXB TRANSLATOR BOARD 10 80 WITHOUT TXB TRANSLATOR BOARD N 04 25 10 80 NOTE VALUES IN PARENTHESES ARE CENTIMETERS ALL OTHERS ARE INCHES C3401M A 1
26. vis CA 93612 5699 USA South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 REVISION HISTORY Manual Date Comments C3401M 12 05 Original version C3401M A 1 06 Added warning about over tightening mounting hardware Pelco the Pelco logo Camclosure Esprit Genex Legacy and Spectra are registered trademarks of Pelco Endura and ExSite are trademarks of Pelco DLP is a registered trademark of Texas Instruments Inc Copyright 2006 Pelco All rights reserved Worldwide Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1 09001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East
Download Pdf Manuals
Related Search
Related Contents
Axor 37134XX1 User's Manual Studio Control with StudioWare and Sysx Owner`s Manual - Stamina Products SuperPro IS03 Manual Hikvision Digital Technology DS-1004KI Benutzerhandbuch analyse de textes socio 06-07 "取扱説明書" Omega OUCHT holder Gembird NCT-4 cable network tester Copyright © All rights reserved.
Failed to retrieve file