Peavey Electronics Stereo System VSX 48 User's Manual
Contents
1. Hr TYPE Available filters are Flat Butterworth 6 12 18 24 30 36 42 and 48 dB oct Bessell 12 18 24 30 36 42 and 48 dB oct Linkwitz Riley 12 24 36 and 48 dB oct The user is free to mix and match filter types to create symmetrical or asymmetrical Crossovers FREQUENCY The VSX is a very powerful tool and as such the frequency points are independent allowing over lapping or under lapping as the system may require The lowest and highest slopes in the chain are useful as high and low system cutoff filters to prevent low frequency rumble and speaker over excursion as well as high frequency interference The filter points are selectable in 1 Hz steps from 20 Hz to 20kHz They may also be selected in the setup configuration screen LEVEL The levels of the crossover sections are independently adjustable from 15 dB to 15 db in 5 dB steps Move the indicator to the plateau and the level parameter appears 13 Delay Screen Inputs A B C amp D or outputs 1 8 should be selected on the top of the screen While on the top of the screen push the data wheel and an arrow appears Rotate the wheel to select which input IH INPUT DELAY or output you wish to adjust Push the data wheel to accept 07 Normally the output delays are used align the phase response HORM of the drivers in a system while the input delays are useful for adding delay to the entire system s ewok D lt ka i2. VSX 48 Digital Loudspeaker Processor Operating Manual www peavey com Intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons Intended to alert the user of the presence of important operating and maintenance servicing instructions in the literature accompanying the product CAUTION Risk of electrical shock DO NOT OPEN CAUTION To reduce the risk of electric shock do not remove cover No user serviceable parts inside Refer servicing to qualified service personnel WARNING To prevent electrical shock or fire hazard this apparatus should not be exposed to rain or moisture and objects filled with liquids such as vases should not be placed on this apparatus Before using this apparatus read the operating guide for further warnings Este s mbolo tiene el prop sito de alertar al usuario de la presencia de voltaje peligroso sin aislamiento dentro de la caja del producto y que puede tener una magnitud suficiente como para constituir riesgo de descarga el ctrica Este s mbolo tiene el prop sito de alertar al usario de la presencia de instruccones importantes sobre la operaci n y mantenimiento en la informaci n que viene con el producto PRECAUCION Riesgo de descarga el ctrica NO ABRIR PRECAUCION Para disminuir el riesgo de descarga el ct
3. While on the top of the screen push the data wheel and an arrow appears Rotate the wheel to select which input or output you wish to adjust and press the data wheel Dynamics in the input channels may be linked in pairs for stereo tracking on the Input pages on the Setup Configuration screen Most users should use the dynamics on the outputs as Limiters to protect speakers and amplifiers and as compressors on the inputs should this type of tonal modification be necessary THRESHOLD The threshold is adjustable in 5 dB steps from 76 dBu to 24 dBu This control determines the minimum level when the compressor begins to limit the dynamic range The compressor has no affect on the signal as long as the signal strength is below the threshold point Once it passes the threshold point the compressor begins to limit the dynamic range of the output according to the value set by the Ratio control THRESH 244 DBY RATIO 1 d DO DE ATTACK 8 g RELEASE 5 RATIO The ratio determines how strong the limiting becomes once the threshold is crossed Values of 1 1 no compression to 20 1 are possible Ratios of 10 1 and above should be selected for speaker protection ATTACK The attack function sets the amount of time for the compressor to respond once the threshold has been crossed Specifying this value allows the user to determine whether the compressor responds as a peak or RMS unit as very short attack times consider only peaks w
4. a bin file 15 VSX 48 BLOCK DIAGRAM gt geen eer alen COMP gt sl 6 PEQ comP DLY 5 6 PEQ coMP 5 PEQ COMP I IDLY OUT sr COMP me 5 PEQ COMP PEQ COMP 5 MIC INPUT s rea cour GENERATOR 16 VSX 48 SPECIFICATIONS Comments Audio Channels 5 inputs 8 outputs Mic input can be summed with Line inputs LED Metering 4 inputs 8 outputs LED STATUS Red 0 5 dBFS and higher Clip Red amp Green 4 to 0 5 dBFS Green 4 to 40 dBFS Off below 40 dBFS Mute Function Front panel switch and LED for each input LED STATUS and output Red Muted Off On Input Trim Range Software controlled Line Sens Settings Software selectable Line Input Impedance Electronically balanced Line Input Crosstalk 20 Hz to 20 kHz Line Input Dynamic Range 150 ohm input termination RTA Mic Gain Range Approximately 1 2 dB steps RTA Max In Gain 60 dB 22K BW RTA Input Impedance Electronically balanced RTA Input ElN 128 dB A weighted 150 ohm input termination RTA Phantom Power 48 volts Software controlled AES Input On XLR 1 Software selectable between left channel analog line input OUTPUTS Output Full Scale 24 dBu Balanced Output Impedance 150 ohms Electronically balanced Minimum Load Impedance 600 ohms Maximum output 600 ohms 22 5 dBu Dynamic Range 105 dB A weighted ANALOG INPUT TO OUTPUT Total Harmonic Distortion 0 007 20 Hz to 20 kH
5. des Erdungssteckers Ein gepolter Stecker weist zwei Stifte auf von denen einer breiter ist als der andere Ein Erdungsstecker weist zwei Stifte und einen dritten Erdungsstift auf Der breite Stift bzw der dritte Stift dient Ihrer Sicherheit Sollte der beiliegende Stecker nicht in Ihre Steckdose passen wenden Sie sich bitte an einen Elektriker um die ungeeignete Steckdose austauschen zu lassen Sch tzen Sie das Netzkabel sodass niemand darauf tritt oder es geknickt wird insbesondere an Steckern oder Buchsen und ihren Austrittsstellen aus dem Gerat Verwenden Sie nur die vom Hersteller erh ltlichen Zubeh rger te oder Zubeh rteile Verwenden Sie nur einen Wagen Stativ Dreifu Tr ger oder Tisch der den Angaben des Herstellers entspricht oder zusammen mit dem Ger t verkauft wurde Wird ein Wagen verwendet bewegen Sie den Wagen mit dem darauf befindlichen Ger t besonders vorsichtig damit er nicht umkippt und m glicherweise jemand verletzt wird Trennen Sie das Ger t w hrend eines Gewitters oder w hrend l ngerer Zeitr ume in denen es nicht benutzt wird von der Stromversorgung Lassen Sie s mtliche Wartungsarbeiten von qualifizierten Kundendiensttechnikern durchf hren Eine Wartung ist erforderlich wenn das Ger t in irgendeiner Art besch digt wurde etwa wenn das Netzkabel oder der Netzstecker besch digt wurden Fl ssigkeit oder Gegenst nde in das Ger t gelangt sind das Ger t Regen oder Feuchtigkeit ausgesetzt wurde ni
6. line level inputs Input A may be switched to AES digital input via software Setup Configuration Screen INPUT SETTINGS Rotate the data wheel to scroll across the screen and push the wheel to select and confirm LELIEL ABC amp D INPUTS EI 40BU 6 46 DE Input sensitivity switches between 10 dBV or 4 dBV inputs HUTE bitt DOHE The 4 dB position should be considered the normal position A GG DE and should be used with professional systems The 10 dB position allows the unit to be driven with hi fi level equipment or directly from a CD player Mute toggle on off Analog digital operation is selectable on input A Level controls digital processing headroom and is adjustable from 0 dB through 100 dB This adjustment is best left as high as possible but may be adjusted as necessary Trim is variable from 6 dB to 6 dB and is used to match analog input sensitivity as necessary Exit this screen by selecting Done and pressing the data wheel or pressing the setup button ST M Toggles between Stereo and Mono Selecting Stereo associates the A B channel inputs It does not affect the output channels When engaged in stereo adjusting a parameter on channel A will make a corresponding adjustment on Ch B This may be most useful when adjusting PEQs Delay or Dynamic settings Preliminary adjustments can be made to both channels in this manner and then the switch ca
7. LCD DISPLAY This screen gives a graphical representation of unit configuration and parameter settings The layout of the screen and the information displayed will depend on the function being monitored or set 4 Parameter Select Buttons SETUP Configurations are selected here Parameter selection for inputs signal generator stereo mono routing matrix and outputs EQ parameter selection of input or output equalizers DYNAMICS parameter selection of input or output compressor limiters XOVER parameters of the bandpass modules for each output or configured crossover DELAY delay time and polarity for each input or output TOOLS saving and loading of presets as well as default configuration 5 Input Output Monitoring LEDs indicate active or muted channel conditions Mute switches are provided to manually mute inputs or outputs Signal LEDs are Green for normal signal level Yellow at 18 dBu output and Red at 20 dBu just before the onset of clipping 6 USB ports Connection of memory stick jump drive for preset storage and system update The slot supports USB 2 0 memory sticks whose current draw is 150 ma or less NOTE Some USB memory sticks with proprietary software may not function correctly Make sure the memory stick is properly formated and there are no autorun programs installed 59 He 14 WATTS 1 IEC POWER INPUT and FUSE HOLDER 2 OUTPUT SECTION XLR male line level outputs 3 INPUT SECTION XLR female
8. T PROFITS LOST SAVINGS DAMAGE TO ANY OTHER EQUIPMENT OR OTHER ITEMS AT THE SITE OF USE OR ANY OTHER DAMAGES WHETHER INCIDENTAL CONSEQUENTIAL OR OTHERWISE EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This Warranty gives you specific legal rights and you may also have other rights which vary from state to state If you have any questions about this warranty or service received or if you need assistance in locating an Authorized Service Center please contact the Peavey International Service Center at 601 483 5365 Features and specifications subject to change without notice OJ L 37 38 13 02 03 and defined in EN 50419 2005 The bar is the symbol for marking of new waste and is applied only to equipment manufactured after 13 August 2005 x Logo referenced in Directive 2002 96 EC Annex IV 19 2009 GA Features and specifications subject to change without notice Peavey Electronics Corporation 5022 Hartley Peavey Drive Meridian MS 39305 601 483 5365 FAX 601 486 1278 e www peavey com EX 000047
9. arro pie tr pode o soporte especificado por el fabricante o vendido junto al aparato Cuando se use un carro tenga cuidado al mover el conjunto carro aparato para evitar que se da e en un vuelco No suspenda esta caja de ninguna manera Desenchufe este aparato durante tormentas o cuando no sea usado durante largos periodos de tiempo Para cualquier reparaci n acuda a personal de servicio cualificado Se requieren reparaciones cuando el aparato ha sido da ado de alguna manera como cuando el cable de alimentaci n o el enchufe se han da ado alg n l quido ha sido derramado o alg n objeto ha ca do dentro del aparato el aparato ha sido expuesto a la lluvia o la humedad no funciona de manera normal o ha sufrido una ca da Nunca retire la patilla de Tierra Escribanos para obtener nuestro folleto gratuito Shock Hazard and Grounding Peligro de Electrocuci n y Toma a Tierra Conecte el aparato s lo a una fuente de alimentaci n del tipo marcado al lado del cable de alimentaci n Si este producto va a ser enracado con m s equipo use alg n tipo de apoyo trasero Nota para el Reino Unido solamente Si los colores de los cables en el enchufe principal de esta unidad no corresponden con los terminales en su enchufe proceda de la siguiente manera a El cable de color verde y azul debe ser conectado al terminal que est marcado con la letra E el s mbolo de Tierra earth coloreado en verde o en verde y amarillo b E
10. cht normal arbeitet oder heruntergefallen ist Der Erdungsstift darf nie entfernt werden Auf Wunsch senden wir Ihnen gerne unsere kostenlose Brosch re Shock Hazard and Grounding Gefahr durch elektrischen Schlag und Erdung zu Schlie en Sie nur an die Stromversorgung der Art an die am Ger t neben dem Netzkabel angegeben ist Wenn dieses Produkt in ein Ger te Rack eingebaut werden soll muss eine Versorgung ber die R ckseite eingerichtet werden Hinweis Nur f r Gro britannien Sollte die Farbe der Dr hte in der Netzleitung dieses Ger ts nicht mit den Klemmen in Ihrem Stecker bereinstimmen gehen Sie folgenderma en vor a Der gr n gelbe Draht muss an die mit E Symbol f r Erde markierte bzw gr ne oder gr n gelbe Klemme angeschlossen werden b Der blaue Draht muss an die mit N markierte bzw schwarze Klemme angeschlossen werden c Der braune Draht muss an die mit L markierte bzw rote Klemme angeschlossen werden Dieses Ger t darf nicht ungesch tzt Wassertropfen und Wasserspritzern ausgesetzt werden und es muss darauf geachtet werden dass keine mit Fl ssigkeiten gef llte Gegenst nde wie z B Blumenvasen auf dem Ger t abgestellt werden Belastung durch extrem hohe L rmpegel kann zu dauerhaftem Geh rverlust f hren Die Anf lligkeit f r durch L rm bedingten Geh rverlust ist von Mensch zu Mensch verschieden das Geh r wird jedoch bei jedem in gewissem Ma e gesch digt der ber einen bestimmten Zeitraum aus
11. encialmente peligrosa se recomienda que todas las personas expuestas a equipamiento capaz de producir altos niveles de presi n sonora tales como este sistema de amplificaci n se encuentren protegidas por protectores auditivos mientras esta unidad est operando GUARDE ESTAS INSTRUCCIONES ENGLISH VSX 48 Digital Loudspeaker Processor The VSX 48 is a fully progammable 32 bit audio processing and louspeaker management control system Considerably more powerful than similarly priced units the VSX 48 provides a versatile and economical alternative for system designers Please read this guide carefully to ensure your personal safety as well as the safety of your equipment Features e 5 inputs 8 outputs e 48 kHz sample rate 24 bit 256x over sampled Delta Sigma AD DA e USB A and B ports for memory storage and computer interface e XLR inputs and outputs e 24 dBu inputs and outputs e Phantom power 48V Front Panel P ra HS gw 4 lt wa F Zeg SES E N map SW 5 CC ES CE E Gi d 6 wr J a ee d Lu Fa 1 ye e AA De gt 4 G PRS lt 4 zeg A Pat a k e P AS Input Section 1 MIC INPUT Front panel Mic or line level input Phantom power may be selected in software May be used as a extra Input and routed through the system 2 DATA WHEEL Rotate clockwise or counter clockwise to scroll through screens Push to enter or confirm selection 3
12. erre ou correspondant aux couleurs verte ou verte et jaune du guide b Le connecteur Bleu doit tre connectrer au terminal not N correspondnat la couleur noire du guide c Le connecteur marron doit tre connectrer au terminal not L correspondant la couleur rouge du guide Cet quipement lectrique ne doit en aucun cas tre en contact avec un quelconque liquide et aucun objet contenant un liquide vase ou autre ne devrait tre pos sur celui ci Une exposition de hauts niveaux sonores peut conduire des dommages de l coute irr versibles La susceptibilit au bruit varie consid rablement d un individu l autre mais une large majorite de la population exp riencera une perte de l coute apres une exposition une forte puissance sonore pour une dur e prolong e L organisme de la sant am ricaine OSHA a produit le guide ci dessous en rapport la perte occasionn e Dur e par Jour heures Niveau sonore moyen dBA 8 90 6 92 4 95 3 97 2 100 1 102 1 105 110 inf rieur 15 D apr s les tudes men es par le OSHA toute exposition au dela des limites d crites 66 0655005 entrainera des pertes de l coute chez la plupart des sujets Le port de syst me de protection casque oreilette de filtrage doit tre observ lors de l op ration cette unit ou des dommages irr versibles peuvent tre occasionn s Le port de ces syst mes doit tre observ par toutes personnes sus cept
13. h wll AEk qe LC m nf d d w AA q e m q IN OUT Toggles to engage or bypass the delay NORM REVERSE Toggles to invert the polarity from the present state It may become necessary to flip the polarity many times while adjusting the delay time or adjusting the cut off rate of the filters It is conveniently located on this page for that purpose DELAY Adds delay to the selected input or output The delay is displayed in milliseconds feet and meters and automatically calculates each as the data wheel is rotated The range of each delay is 340 ms 379 09 feet and 115 59 meters The input delay amount will be added to the output delay amount for a possible 680 ms 758 18 feet and 231 18 meters should a very long delay be necessary One example would be for use with delay towers 14 IMPORTANT WHEN LOADING NEW PRESETS FROM MEMORY STICK BE SURE TO MUTE ALL OUTPUTS AND TURN YOUR POWER AMPLIFIERS DOWN OR OFF CORRUPT DATA CAN CAUSE UNDESIRABLY RESULTS THAT COULD POTENTIALLY DAMAGE YOUR SPEAKERS SAVE PRESET _ Allows saving the current configuration to one of 8 internal LOAD SETTINGS USB MEMSTICK C JE memory positions or to an external USB memory stick If external USB is selected the VSX will automatically write a folder and file to the stick without disturbing other files folders that may be present o
14. hile times above 50 ms average these peaks and result in RMS response We recommend attack times of between 50 ms 100 ms be used when setting the limiters to protect the speakers from being overdriven by the power amps It is the average power long term that causes speaker burn out The transient peaks usually cause little damage if kept inside the speaker s band limits 12 RELEASE The Release value sets the amount of time for the compressor to recover from the compressed state once the level falls below the threshold level We recommend release times of 5x to 10x the Attack time in normal use GAIN This adjustment serves to compensate for the loss in average signal strength due to compression The range is 100 dB to 30 dB IN OUT This button toggles to bypass the dynamics section The output channel numbers appear across the top of the screen Depending on the configuration template chosen they may appear together as blocks representing 2 way 3 way or 4 way crossovers or singly as a Bandpass filter After making a selection rotate the data wheel to adjust parameters Each bandpass filter associated with the crossover is represented graphically on the screen The two slopes represent the lower and upper frequencies of the bandpass and the plateau represents the level of the bandpass The intersection of slopes represents the electrical crossover point s 1 2 3 5 SE QUTi OUT TYPE FLAT FREQ Z
15. ibles d tre expos es a des conditions au dela des limites d crites ci dessus GARDEZ CES INSTRUCTIONS INSTRUCCIONES IMPORTANTES PARA SU SEGURIDAD CUIDADO Cuando use productos electr nicos debe tomar precauciones b sicas incluyendo las siguientes 1 OS ae 10 11 12 13 14 15 16 17 18 19 Lea estas instrucciones 6 6 Guarde 65185 instrucciones Haga caso de todos los consejos Siga todas las instrucciones No usar este aparato cerca del agua Limpiar solamente con una tela seca No bloquear ninguna de las salidas de ventilaci n Instalar de acuerdo a las instrucciones del fabricante No instalar cerca de ninguna fuente de calor como radiadores estufas hornos u otros aparatos incluyendo amplificadores que produzcan calor No retire la patilla protectora del enchufe polarizado o de tipo a Tierra Un enchufe polarizado tiene dos puntas una de ellas m s ancha que la otra Un enchufe de tipo a Tierra tiene dos puntas y una tercera a Tierra La punta ancha la tercera se proporciona para su seguridad Si el enchufe proporcionado no encaja en su enchufe de red consulte a un electricista para que reemplaze su enchufe obsoleto Proteja el cable de alimentaci n para que no sea pisado o pinchado particularmente en los enchufes huecos y los puntos que salen del aparato Usar solamente a adidos accesorios proporcionados por el fabricante Usar solamente un c
16. ith manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding plug The wide blade or third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point they exit from the apparatus Only use attachments accessories provided by the manufacturer Use only with a cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Never break off the ground pin Write for our free booklet Shock Ha
17. l cable coloreado en azul debe ser conectado al terminal que est marcado con la letra N o el color negro c El cable coloreado en marr n debe ser conectado al terminal que est marcado con la letra Lo el color rojo Este aparato el ctrico no debe ser sometido a ning n tipo de goteo o salpicadura y se debe tener cuidado para no poner objetos que contengan l quidos como vasos sobre el aparato La exposici n a altos niveles de ruido puede causar una p rdida permanente en la audici n La susceptibilidad a la p rdida de audici n provocada por el ruido var a seg n la persona pero casi todo el mundo perder algo de audici n si se expone a un nivel de ruido suficientemante intenso durante un tiempo determinado El Departamento para la Salud y para la Seguridad del Gobierno de los Estados Unidos OSHA ha especificado las siguientes exposiciones al ruido permisibles Duraci n por D a en Horas Nivel de Sonido dBA Respuesta Lenta 8 90 6 92 4 95 3 97 2 100 1 102 1 105 110 o menos 115 De acuerdo al OSHA cualquier exposici n que exceda los limites arriba indicados puede producir alg n tipo de p rdida en la audici n Protectores para los canales auditivos o tapones para los o dos deben ser usados cuando se opere con este sistema de sonido para prevenir una p rdida permanente en la audici n si la exposici n excede los l mites indicados m s arriba Para prote gerse de una exposici n a altos niveles de sonido pot
18. less 115 According to OSHA any exposure in excess of the above permissible limits could result in some hearing loss Ear plugs or protectors to the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss if exposure is in excess of the limits as set forth above To ensure against potentially dangerous exposure to high sound pressure levels it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation SAVE THESE INSTRUCTIONS WICHTIGE SICHERHEITSHINWEISE ACHTUNG Beim Einsatz von Elektroger ten m ssen u a grundlegende Vorsichtsmafinahmen befolgt werden 1 a EE e 10 11 12 13 14 15 16 17 18 19 Lesen Sie sich diese Anweisungen durch 6 6 Bewahren Sie diese Anweisungen auf Beachten Sie alle Warnungen Befolgen Sie alle Anweisungen Setzen Sie dieses Ger t nicht in der N he von Wasser ein Reinigen Sie es nur mit einem trockenen Tuch Blockieren Sie keine der L ftungs ffnungen F hren Sie die Installation gem den Anweisungen des Herstellers durch Installieren Sie das Ger t nicht neben W rmequellen wie Heizungen Heizger ten Ofen oder anderen Ger ten auch Verstarkern die Warme erzeugen Beeintrachtigen Sie nicht die Sicherheitswirkung des gepolten Steckers bzw
19. n be toggled to mono allowing further independent adjustment of single inputs The switch may be toggled again to link up the dynamic sections for stereo tracking of the comp limiters HIC SETTINGS MIC Allows engaging the 48 V phantom power as well as adjusting SA DEF the Mic gain range from 23 dB to 67 dB of gain Select done or CAH 46 7 DB press setup to escape to the main screen GEN This screen selects the parameters for the signal generator Pink White or Sine may be selected When Sine is selected the EE frequency of the sine wave may be adjusted for 20 Hz to 20 kHz f SIGHAL GENERATOR The output level may be adjusted by highlighting the fader graphic w and adjusting the Level control An In Out button is provided CS to turn on and off the generator The screen may be exited by CHITE selecting done or pressing the setup button The Generator SINE must be assigned to an output of your choice with the Matrix A single Band pass filter can also be assigned to that output and 1800 Hz LTH Done the skirts may be adjusted to provide limited bandwidth noise for testing purposes MATRIX The matrix provides the method to assign inputs to outputs In the default configuration NO SIGNAL IS PASSED through the unit until some selection in the matrix is made This prevents potentially destructive signals from reaching the wrong outputs The inputs are represented by the rows and the o
20. n the stick It is not necessary to dedicate a memory stick to the exclusive service of the VSX Files from the stick may be transferred to a PC or MAC computer UF CANCEL Note Configuration presets are stored in the folder VSX48 presets on the memory stick NAME Selecting this function opens a alpha numeric keyboard The VSX M DEDI allows 8 characters to name the file The Right Arrow button on Qi the bottom right returns to the Save screen tes OK LESSING Must be selected and the data wheel pushed to actually save the CU LE LAN IN LES LA EI LE preset You will be asked to confirm this on the next screen LOAD SETTINGS Rotate the data wheel to select from the eight internal presets and from an external memory stick if it is plugged in Press OK and it PRESET E will load the preset to the current preset A confirmation screen will C JE En appear before overwriting the current preset UF CANCEL INSTALLING SOFTWARE UPDATES Press and hold in the data wheel while powering up Insert a memory stick or connect via USB to a computer The VSX will search for files and will display a list Select the desired version by highlighting it and press the Data Wheel A confirmation screen will appear Cursor over to yes and press the Data Wheel The VSX will automatically perform the upgrade from here When downloading the upgrade from the web place it in a folder VSX48 firmware The upgrade file will be
21. reichend starkem L rm ausgesetzt ist Die US Arbeitsschutzbeh rde Occupational and Health Administration OSHA hat die folgenden zul ssigen Pegel f r L rmbelastung festgelegt Dauer pro Tag in Stunden Ger uschpegel dBA langsame Reaktion 8 90 6 92 4 95 3 97 2 100 1 102 1 105 110 oder weniger 115 Laut OSHA kann jede Belastung ber den obenstehenden zul ssigen Grenzwerten zu einem gewissen Geh rverlust f hren Sollte die Belastung die obenstehenden Grenzwerte bersteigen m ssen beim Betrieb dieses Verst rkungssystems Ohrenstopfen oder Schutzvorrichtungen im Geh rgang oder ber den Ohren getragen werden um einen dauerhaften Geh rverlust zu verhindern Um sich vor einer m glicherweise gef hrlichen Belastung durch hohe Schalldruckpegel zu sch tzen wird allen Personen empfohlen die mit Ger ten arbeiten die wie dieses Verst rkungssystem hohe Schalldruckpegel erzeugen k nnen beim Betrieb dieses Ger ts einen Geh rschutz zu tragen BEWAHREN SIE DIESE SICHERHEITSHINWEISE AUF 4 ATTENTION L utilisation de tout appareil lectrique doit tre soumise aux precautions d usage incluant NON ONE SA 00 9 15 16 17 18 19 INSTRUCTIONS IMPORTANTES DE SECURITE CE Lire ces instructions Gardez ce manuel pour de futures r f rences Pr tez attention aux messages de pr cautions de ce manuel Suivez ces instructions N utilisez pas cette unit proche de plans d eau N utilisez qu un tis
22. repair or replace at Peavey s discretion products covered by warranty at no charge for labor or materials If the product or component must be shipped to Peavey for warranty service the consumer must pay initial shipping charges If the repairs are covered by warranty Peavey will pay the return shipping charges How To Get Warranty Service 1 Take the defective item and your sales receipt or other proof of date of purchase to your Authorized Peavey Dealer or Authorized Peavey Service Center OR 2 Ship the defective item prepaid to Peavey Electronics Corporation International Service Center 412 Highway 11 amp 80 East Meridian MS 39301 Include a detailed description of the problem together with a copy of your sales receipt or other proof of date of purchase as evidence of warranty coverage Also provide a complete return address Limitation of Implied Warranties ANY IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Exclusions of Damages PEAVEY S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT AT PEAVEY S OPTION IF WE ELECT TO REPLACE THE PRODUCT THE REPLACEMENT MAY BE A RECONDITIONED UNIT PEAVEY SHALL NOT BE LIABLE FOR DAMAGES BASED ON INCONVENIENCE LOSS OF USE LOS
23. rica no abra la cubierta No hay piezas tiles dentro Deje todo mantenimiento en manos del personal t cnico cualificado ADVERTENCIA Para prevenir choque electrico o riesgo de incendios este aparato no se debe exponer a la lluvia o a la humedad Los objetos llenos de liquidos como los floreros no se deben colocar encima de este aparato Antes de usar este aparato lea la guia de funcionamiento para otras advertencias Ce symbole est utilis dans ce manuel pour indiquer a l utilisateur la pr sence d une tension dangereuse pouvant tre d amplitude suffisante pour constituer un risque de choc lectrique Ce symbole est utilis dans ce manuel pour indiquer l utilisateur qu il ou qu elle trouvera d importantes instructions concernant l utilisation et l entretien de l appareil dans le paragraphe signal ATTENTION Risques de choc lectrique NE PAS OUVRIRI ATTENTION Afin de r duire le risque de choc lectrique ne pas enlever le couvercle Il ne se trouve l int rieur aucune pi ce pouvant tre repar e par l utilisateur Confiez l entretien et la r paration de l appareil un r parateur Peavey agr AVIS Dans le but de reduire les risques d incendie ou de decharge electrique cet appareil ne doit pas etre expose a la pluie ou a l humidite et aucun objet rempli de liquide tel qu un vase ne doit etre pose sur celui ci Avant d utiliser de cet appareil lisez attentivement le guide fonctionnant pour avertissemen
24. ship in Peavey products purchased and serviced in the U S A and Canada What This Warranty Does Not Cover The Warranty does not cover 1 damage caused by accident misuse abuse improper installation or operation rental product modification or neglect 2 damage occurring during shipment 3 damage caused by repair or service performed by persons not authorized by Peavey 4 products on which the serial number has been altered defaced or removed 5 products not purchased from an Authorized Peavey Dealer Who This Warranty Protects This Warranty protects only the original retail purchaser of the product How Long This Warranty Lasts The Warranty begins on the date of purchase by the original retail purchaser The duration of the Warranty is as follows Product Category Duration Guitars Basses Amplifiers Pre Amplifiers Mixers Electronic Crossovers and Equalizers 2 years 3 years Drums 2 years I year Enclosures 3 years 2 years Digital Effect Devices and Keyboard and MIDI Controllers I year I year Microphones 2 years Speaker Components incl speakers baskets drivers diaphragm replacement kits and passive crossovers and all Accessories I year Tubes and Meters 90 days Denotes additional warranty period applicable if optional Warranty Registration Card is completed and returned to Peavey by original retail purchaser within 90 days of purchase What Peavey Will Do We will
25. su sec pour le nettoyage de votre unit N obstruez pas les syst mes de refroidissement de votre unit et installez votre unit en fonction des instructions de ce manuel Ne positionnez pas votre unit proximit de toute source de chaleur Connectez toujours votre unit sur une alimentation munie de prise de terre utilisant le cordon d alimentation fourni Prot gez les connecteurs de votre unit et positionnez les cablages pour viter toutes d connexions accidentelles N utilisez que des fixations approuv es par le fabriquant Lors de l utilsation sur pied ou pole de support assurez dans le cas de d placement de l ensemble enceinte support de pr venir tout basculement intempestif de celui ci Il est conseill de d connecter du secteur votre unit en cas d orage ou de dur e prolong e sans utilisation Seul un technicien agr par le fabriquant est m me de r parer contr ler votre unit Celle ci doit tre contr l e si elle a subit des dommages de manipulation d utilisation ou de stockage humidit Ne d connectez jamais la prise de terre de votre unit Si votre unit est destin e a etre mont e en rack des supports arriere doivent etre utilises Note pour les Royaumes Unis Si les couleurs de connecteurs du cable d alimentation ne correspond pas au guide de la prise secteur proc dez comme suit a Le connecteur vert et jaune doit tre connectrer au terminal not E indiquant la prise de t
26. ts suppl mentaires Dieses Symbol soll den Anwender vor unisolierten gefahrlichen Spannungen innerhalb des Gehauses warnen die von Ausreichender Starke sind um einen elektrischen Schlag verursachen zu k nnen Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen die Handhabung und Wartung des Produkts betreffen VORSICHT Risiko Elektrischer Schlag Nicht ffnen VORSICHT Um das Risiko eines elektrischen Schlages zu vermeiden nicht die Abdeckung enfernen Es befinden sich keine Teile darin die vom Anwender repariert werden k nnten Reparaturen nur von qualifiziertem Fachpersonal durchf hren lassen WARNUNG Um elektrischen Schlag oder Brandgefahr zu verhindern sollte dieser Apparat nicht Regen oder Feuchtigkeit ausgesetzt werden und Gegenst nde mit Fl ssigkeiten gefuellt wie Vasen nicht auf diesen Apparat gesetzt werden Bevor dieser Apparat verwendet wird lesen Sie bitte den Funktionsf hrer f r weitere Warnungen IMPORTANT SAFETY INSTRUCTIONS WARNING When using electrical products basic cautions should always be followed including the following 1 DNS ok D 10 11 12 13 14 15 16 17 18 19 Read these instructions 6 6 Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a dry cloth Do not block any of the ventilation openings Install in accordance w
27. utputs by the columns Most users will commonly assign crossovers in the setup screen so that only a single input assignment will be necessary In addition to the line inputs the Mic and GEN inputs are assigned in this screen To continue from the matrix you must exit from the upper left or the lower right squares 10 Setup Configuration Screen SETUP Selecting this button takes you to the preset configuration page The VSX is pre programmed with fourteen configuration ere dE e templates representing the most frequently used crossover F42 41000 Hz Tt possibilities As you scroll through the configuration presets you are 1000 MZ uy 1 will see and can adjust the basic filter types only symmetrical 56 2 LE choices may be made here Center frequencies of those filters and a graphic representation of the filters will be displayed You must enter OK to accept the selection Selecting and pressing Exit or pressing the Setup button will return you to the main screen Upon returning to the main screen you will see the graphic representation of your selection OUTPUT 1 8 Output levels may be adjusted on this page Press done or push the setup button to return to the main screen Inputs or outputs should be selected on the top of the screen g While on the top of the screen push the data wheel and an arrow DI IBICID 3 11213 451617 je appears Rotate the wheel to select which input or output you
28. wish to adjust PARAMETRIC EQs on inputs Inputs A thru D display a graphical representation of the six parametric EQs that are available on each input BW Bandwidth in oct F Frequency being adjusted LVL Level control After selecting a frequency rotating the data wheel allows boosting or cutting the amplitude of the selected frequency 15 dB in 5 dB increments Tip Pressing the EQ button is a short cut to return to the top of the screen 11 OUTPUT EQUALIZERS Select 1 8 on the top of the EQ screen FILTER 10F 5 TYPE PARAMETRIC El FRE 1666 Hz 16 067 LEVEL DE FILTER Select any of the five independent filters to use B TYPE Choices are Parametric Notch Allpass1 Allpass2 Horn EQ LPF 6 LPF 12 HPF 6 HPF 12 Low Shelf High Shelf and Bandpass Depending on the filter selected various options for adjustment are presented in the window Parametric Frequency BW in oct Level Notch Frequency BW in oct Notch has a fixed attenuation on minus infinity and the BW is defined 3 dB from unity All Pass1 Frequency All Pass2 Frequency and Bandwidth Horn EQ Turnover Frequency and Level LPF6 and HPF6 Frequency LPF12 and HPF12 Frequency and Q Low and High Shelf Frequency and Level Bandpass Center Frequency and Bandwidth Dynamics DYNAMICS Inputs A B C amp D or outputs 1 8 should be selected on the top of the screen
29. z 22 kHz BW Noise filter 4 dBu signal with 20 dB headroom Frequency Response 20 Hz to 20 kHz 0 5 dBr referenced at 1 kHz Dynamic Range 105 dB A weighted 150 ohm input termination Latency gt 1 msS Propagation delay from input to output VSX 48 SPECIFICATIONS Comments DIGITAL Sample Rate QUANTIZATION 24 bit 256 x over sampled Delta Sigma AD DA Digital Processing 100 32 bit MIP Uses Analog Devices BLACKFIN processors 40 bit accumulators DSP Cycle Speed 500 MHZ u 5 CONTROL MEMORY USB 2 0 PC Memory Stick PDA Connection GENERAL Dimensions 19 48 26 cm W without connectors 12 25 31 12 cm D 3 5 8 89 cm H Net Weight 1 6 bs 6 26 kg AC Power Input Voltage 100 240 VAC 47 63 Hz Universal Power Supply Power Consumption 14 watts 120 V 163 mA Power Dissipation 47 Btu 11 8 kcal 120 V Agency Compliance Listings UL CUL CE FCC part 15 Class B Unless otherwise noted 1 All specifications are typical for any channel s 2 All measurements are made in the digital domain 3 All specifications are for an AC line input of 120 volts RMS 4 All input measurements are made using a 40 ohm balanced source impedance at 24 dBu full scale 5 All measurements are made with gain attenuation set for unity 18 PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY Effective Date July 1 1998 What This Warranty Covers Your Peavey Warranty covers defects in material and workman
30. zard and Grounding Connect only to a power supply of the type marked on the unit adjacent to the power supply cord If this product is to be mounted in an equipment rack rear support should be provided Note for UK only If the colors of the wires in the mains lead of this unit do not correspond with the terminals in your plug proceed as follows a The wire that is colored green and yellow must be connected to the terminal that is marked by the letter E the earth symbol colored green or colored green and yellow b The wire that is colored blue must be connected to the terminal that is marked with the letter N or the color black c The wire that is colored brown must be connected to the terminal that is marked with the letter L or the color red This electrical apparatus should not be exposed to dripping or splashing and care should be taken not to place objects containing liquids such as vases upon the apparatus Exposure to extremely high noise levels may cause a permanent hearing loss Individuals vary considerably in susceptibility to noise induced hearing loss but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time The U S Government s Occupational Safety and Health Administration OSHA has specified the following permissible noise level exposures Duration Per Day In Hours Sound Level dBA Slow Response 8 90 6 92 4 95 3 97 2 100 1 1 2 102 1 105 12 110 14 or
Download Pdf Manuals
Related Search