Peavey 210HP User's Manual
Contents
1. 210HP POWERED ENCLOSURE OPERATING GUIDE CAUTION TO PREVENT ELECTRICAL SHOCK OR FIRE HAZARD DO NOT EXPOSE THIS INSTRU MENT TO RAIN OR MOISTURE BEFORE USING THIS INSTRUMENT READ BACK COVER FOR FURTHER WARNINGS The 210HP isa powered two way enclosure designed primarily tobe used for biamp applications in conjunction with bass guitar amplification systems While this product should not be used as a full range bass guitar system it will function well as a powered sound reinforcement monitor or for general purpose PA The speaker system consists of two 10 inch Scorpion loudspeakers CH 3 horn with the model 22A compression driver and a passive high level crossover The power amplifier 500 BH is rated at 210 watts at 4 ohms and features DDT Distortion Detection Technique U S Patent 4 318 053 which prevents the amplifier from severe clipping When used in a biamp configuration the recommended crossover frequency between the 210HP and the associated subwoofer is 250 Hz to 500 Hz 1 MAIN POWER AMP INPUT Use to connect line level signal to power amplifier 2 AUXILIARY POWER AMP INPUT Use to send line level signal to additional power amplifier DAISY CHAIN Will not operate unless main input is connected 3 LEVEL Controls the volume level of the enclosure LINE CORD For your safety we have incorporated a 3 wire line mains cable on the back of the chassis with proper grounding facilities It is n2. E 250 VOLTS Fey crnzs SOO BH A PRODUCT OF PEAVEY ELECTRONICS CORPORATION MERIDIAN MS MADE IN USA BUILT UNDER US PATENT NOS 4318053 AND 4 348 788 210HP POWERED ENCLOSURE SPECIFICATIONS 500 BH MODULE WITH DDT COMPRESSION RATED POWER amp LOAD 210W RMS into 4 ohms 300W RMS into 2 ohms POWER CLIPPING TYPICALLY 5 THD 1 kHz 120 VAC Line 130W RMS into 8 ohms 225W RMS into 4 ohms 320W RMS into 2 ohms AMPLIFIER FREQUENCY RESPONSE 0 1 dB 20 Hz to 20 kHz 200 watts into 4 ohms SYSTEM RESPONSE 90 Hz to 16 kHz 3 dB TOTAL HARMONIC DISTORTION Less than 0 1 200 mW to 200W RMS 20 Hz to 10 kHz 4 ohms Typically below 0 05 INTERMODULATION DISTORTION Less than 0 1 200 mW to 200W RMS 60 Hz amp 5 kHz 4 ohms Typically below 0 05 DDT DYNAMIC RANGE Greater than 26 dB DDT MAXIMUM TOTAL HARMONIC DISTORTION 1 kHz Below 0 5 THD for 6 dB overload Below 1 THD for 20 dB overload HUM amp NOISE Greater than 90 dB below rated power INPUT SENSITIVITY 1V RMS 0 dBV for full power output INPUT IMPEDANCE 50K ohms POWER CONSUMPTION DOMESTIC 800 watts 50 60 Hz 120 VAC WEL oovements coo PaTiONA sarery ano ut oun Eh HAS SPECIFIED TE FOLL OWING SERWESBLE nolge LEVEL Eaeosuaes ORATION PER DAY IN TAU Er are wc en ra asap ot or i i Due to our efforts for constant improvement features and specifications are subject to change without notice PEAVEY ELEC
3. TRONICS CORPORATION 711 A STREET MERIDIAN MS 39301 TELEPHONE 601 483 5365 TELEX 504115 1986 PRINTED INUSA 80300532 2 86
4. ot advisable to remove the ground pin under any circumstances If it is neces sary to use the amplifier without proper grounding facilities suitable grounding adapters should be used Less noise and greatly reduced shock hazard exists when the unit is operated with the proper grounded receptacles NOTE The above statement in reference to removing the ground pin is applicable only to 120 volt model products 5 POWER SWITCH Center position is OFF Two ON positions are provided one of which will properly ground the amplifier Switch to the on side that yields the low est amount of residual hum or popping noise when the instrument is touched 220 and 240 volt models utilize a two way ON OFF switch only 6 FUSE The fuse is located within the cap of the fuseholder If the fuse should fail IT MUST BE REPLACED WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE TO THE EQUIPMENT AND TO PREVENT VOIDING THE WARRANTY If the amp repeatedly blows fuses it should be taken to a qualified service center for repair WARNING THE FUSESHOULD ONLY BE REPLACED WHEN THE POWER CORD HAS BEEN DISCON NECTED FROM ITS POWER SOURCE 7 PILOT LIGHT Illuminates when AC power is being supplied to the amp gt QR Levante 4 300 WATTS 2 OHMS 210 WATTS 4 OHMS POWER 800 WATTS ON al HAZARD REPLACE WITH SAME TYPE 250 VOLT FUSE AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR REMPLACER PAR UN FUSIBLE DE MEME TYPE ET D
Download Pdf Manuals
Related Search