Panasonic BT-LH1760 Menu Information
Contents
1. FUNCTION GPI INPUT SELECT AUDIO DISPLAY SETUP CONTROL HOURMETER AAA dd dd 4 dd MENU EXIT MASEL ENTERJENTER Displays instructions on menu button operations 13 How to Use the On Screen Menu continued Time code TC display LTC 01 02 10 02 LUB 01 02 10 02 e Use the menu to display the time code for HD SDI signal input It also allows you to switch display mode VITC LTC VUB LUB In VITC and LTC display mode e Displays the time code in hours minutes seconds or frames e In drop frame mode a different delimiter between seconds and frames is used Note Read errors are displayed as In VUB and LUB display modes e BG8 BG7 BG6 BG5 BG4 BG3 BG2 BG1 appear in the stated order BG binary group e The delimiter does not appear Note Read errors are displayed as Closed caption CC display CLOSED CAPTION Closed caption display area 82 columns 14 e Use the menu to display closed caption for VIDEO NTSC signals It also allows you to select display mode CC1 to CC4 Note Closed captions are not available during HV DELAY How to Use the On Screen Menu continued Menu operations 1 Press MENU to display the MAIN menu N ODVI D MENU y A ENTER 1 2 3 2 Press V A to select a menu and press ENTER MAIN MENU gt VIDEO CONFIG SYSTEM CONFIG2. STATUS CONTINUE Sets display state for input signal status on screen menu DISPLAY 3SEC OFF lt CONTINUE gt Displayed at all times OFF lt 3SEC OFF gt Displayed for 3 seconds after a status change lt OFF gt Not displayed SETUP LOAD USERS 1 Loads saved factory defaults FACTORY or user data USER1 USERS USERA u After loading user data the screen displays the signal selected before USER2 2 user data was loaded USER1 1 FACTORY SETUP SAVE USERS Up to 5 sets of user data can be saved gt page 16 USER4 They save menu settings and adjustments made with the picture adjusting aij knob PHASE CHROMA BRIGHT CONTRAST BACKLIGHT except 2 SETUP SAVE SETUP LOAD USER1 POWER ON USER5 Selects the settings used when the power is turned on SETUP USER4 lt LAST gt Starts in the mode used when the power was last turned off ik lt FACTORY gt Starts up using the factory defaults USER1 lt USER1 5 gt Starts up using USER registered settings FACTORY LAST COLOR SPACE SMPTE C Sets the studio standard color shade EBU ITU 709 4 POWER SAVE OFF Sets the power save mode MODE ON lt ON gt The backlight dims when no signal NO SIGNAL is input for 60 seconds or longer Signal input or menu operation will return the backlight to its normal brightness BLACK DATA OFF Doubles the speed of the LCD panel INSERTION ON lt ON gt Double speed 120 Hz 100 Hz lt OFF gt Standard speed 60 Hz 50 Hz 1 When the monitor is shipped
3. lt 93 16 9 gt 93 area marker for 16 9 aspect ratio 93 4 3 lt 90 16 9 gt 90 area marker for 16 9 aspect ratio 90 4 3 lt 88 16 9 gt 88 area marker for 16 9 aspect ratio 88 4 3 lt 80 16 9 gt 80 area marker for 16 9 aspect ratio 80 4 3 lt 95 4 3 gt 95 area marker for 4 3 aspect ratio lt 93 4 3 gt 93 area marker for 4 3 aspect ratio lt 90 4 3 gt 90 area marker for 4 3 aspect ratio lt 88 4 3 gt 88 area marker for 4 3 aspect ratio lt 80 4 3 gt 80 area marker for 4 3 aspect ratio MARKER TYPE TYPE1 Selects conventional monitor or camera recorder marker size TYPE2 lt TYPE1 gt Conventional monitor marker size lt TYPE2 gt Marker size compliant with the camera recorder Panasonic CROSS HATCH HIGH Turns the cross hatch grid on and off and sets its density LOW lt HIGH gt 70 256 displays a dense cross hatch grid OFF lt LOW gt 20 256 displays a light cross hatch grid lt OFF gt Turns the display off 1 This setting is turned ON when receiving marker control in REMOTE operation GPI if set has priority 2 These settings are disabled when the GPI function gt page 36 is used to control the marker setting They are also disabled in split screen mode 3 This setting is enabled only for HD and SD signal input in 16 9 aspect ratio mode 4 This setting is enabled for SD signal input in 4 3 aspect ratio mode 5 Remote control via RS 232C ends in error error response ER
4. settings for USER1 USERS are identical to FACTORY 2 H POSITION V POSITION PHASE and CLOCK gt page 31 cannot be saved or loaded 3 Double speed reduces image lag caused by black signal input but lowers resolution compared to standard speed and some images may generate flicker Return to standard speed should flicker become noticeable 4 ITU 709 is an ITU R BT 709 standard 5 Factory preset settings are The U S A and Canada SMPTE C Others EBU 22 Main Menu continued FUNCTION Underlined values indicate factory defaults Sub menu Settings Description FUNCTION 1 HV DELAY Selects functions to be assigned to FUNCTION1 FUNCTION5 FUNCTION 5 AUTOSETUP front panel buttons BLUE ONLY lt HV DELAY gt GAMMA SELECT Displays synchronizing signals horizontal vertical SD ASPECT The display changes in the following order SCAN DELAY OFF gt V DELAY gt H DELAY gt HV DELAY gt DELAY OFF SUB WINDOW lt AUTOSETUP gt WFM VECTOR Performs auto setup for PC display MARKER lt BLUE ONLY gt PIXEL TO PIXEL Cuts the red and green signals Use this function to check phase and PIXEL POSITION chroma This button toggles between ON and OFF LEVEL METER lt GAMMA SELECT gt CROSS HATCH Displays the gamma curve MONO The display changes in the following order TIME CODE GAMMA STANDARD gt GAMMA FILM gt GAMMA STDIO PST CLOSED GAMMA STANDARD CAPTION lt SD ASPECT
5. HATCH function is assigned changes the display as shown HD SD 16 9 mode 2nd press 1st press gt 3rd press back to original image without cross hatch 28 Main Menu continued GPI CONTROL is used to enable and disable GPI functions and assign functions to each of the GPI terminal pins gt page 36 Underlined values indicate factory defaults Sub menu Settings Description GPI CONTROL DISABLE ENABLE Enables and disables GPI functions lt DISABLE gt Disabled lt ENABLE gt Enabled GPI1 GPI8 UNDEF MARKER1 ON OFF MARKER2 ON OFF MARKER BACK HALF MARKER BACK BLACK CENTER MARKER INPUT SEL VIDEO INPUT SEL SDI1 INPUT SEL SDI2 INPUT SEL YPsPr RGB INPUT SEL DVI D SD ASPECT SCAN R TALLY G TALLY MONO GAMMA SEL FILM GAMMA SEL STDIO PST SELECT SYNC PIXEL TO PIXEL Assigns functions to the GPI control terminal pins The same items can be set to each terminal gt page 36 Note This function is not available when e SD ASPECT operation when input signal is HD or PC SCAN operation when the input signal is PC e GAMMA SELECT operation when the input signal is PC e SELECT SYNC operation when anything other than RGB VIDEO is selected under YPsPr RGB in the INPUT SELECT menu e MONO operation when input signal is PC 29 Main Menu continued INPUT SELECT Underlined value
6. VECTOR display gt page 33 Press the button FUNCTION1 to FUNCTIONS gt page 23 to which the WFM VECTOR function has been assigned to turn the function on and off This assumes that the WFM VECTOR function has been assigned to any of the FUNCTION1 to FUNCTION5 buttons g Press the FUNCTION button to which the WFM VECTOR function has been assigned B Normal screen GE a y EL a DOS Press the button again gt 1 Displayed only for SDI signal input 26 WFM display WFM waveform display Press the button again D VECTOR display VECTOR vector display These examples show 16 9 aspect ratio images Main Menu continued E PIXEL TO PIXEL and PIXEL POSITION The PIXEL TO PIXEL function allows you to check images at their actual pixel resolution 1080I P signals only Press the button FUNCTION1 to FUNCTIONS gt page 23 to which the PIXEL TO PIXEL function has been assigned to turn the function on Then press the button FUNCTION1 to FUNCTIONS gt page 23 to which the PIXEL POSITION function has been assigned to position the display of signals This assumes that the PIXEL TO PIXEL and PIXEL POSITION functions have been assigned to any of the FUNCTION 1 to FUNCTIONS buttons Underlined values indicate factory defaults Sub menu Settings Description PIXEL TO PIXEL OFF Tailors the ima
7. appear on the screen can be adjusted e The display always appears in the same screen PHASE 32 i eee location Display status PHASE CHROMA BRIGHT CONTRAST or BACKLIGHT Note The status of the volume knob does not appear on the screen Sharpness display e This is the SHARPNESS H V mode display e It disappears after 2 minutes of inaction SHARPNESS H 30 How to Use the On Screen Menu continued FUNCTION display e Use the menu to open and set up functions e When FUNCTION DISPLAY gt page 23 is set to ON press any of the FUNCTION1 to FUNCTIONS buttons to display the functions F1 MARKER assigned to the FUNCTION buttons F2 WFM VECTOR e This display disappears after 2 seconds of inaction F3 PIXEL TO PIXEL e XXXXX indicates operating status gt page 25 F4 TIME CODE Functions displayed during FUNCTION button F5 LEVEL METER operation XXXXX Audio level meter display e A white skeleton bar meter indicates the audio level for SDI signals e You can switch the level display on off and set the number of displayed channels using the menu e The 0 dB line and channel display can be switched on off from the menu Channel Level 0 dB line display display Menu display e This is the menu display MAIN MENU e It disappears after 2 minutes of inaction gt e You can change position of the display gt page 22 VIDEO CONFIG MENU POSITION SYSTEM CONFIG
8. gt UNDEF Switches between 16 9 and 4 3 lt SCAN gt Switches between UNDER SCAN and NORMAL SCAN lt SUB WINDOW gt Sets the split screen function The display changes in the following order SINGLE gt FULL PART gt STILL gt SINGLE Factory default lt WFM VECTOR gt FUNCTION1 Displays waveform or vector display MARKER lt MARKER gt FUNCTION2 Turns the marker on and off WFM VECTOR lt PIXEL TO PIXEL gt FUNCTIONS Turns the PIXEL TO PIXEL function On and Off PIXEL TO PIXEL lt PIXEL POSITION gt FUNCTIONA4 Positions the display of signals in PIXEL TO PIXEL mode TIME CODE lt LEVEL METER gt FUNCTIONS Turns the LEVEL METER display On and Off LEVEL METER lt TIME CODE gt Turns the time code display on and off lt MONO gt Switches between color and monochrome lt CLOSED CAPTION gt Turns the closed caption display on and off lt UNDEF gt Undefined FUNCTION OFF Selects display of functions assigned to FUNCTION1 DISPLAY ON1 FUNCTIONS front panel buttons It also selects button action 1 ON2 touch 2 touch off lt ON1 gt 1 touch action to display and perform functions lt ON2 gt 2 touch action to display and perform functions lt OFF gt No function display 1 Changes in settings change menu settings 23 Main Menu continued E FUNCTION setting restrictions Settings are not available under the following conditions Setting Conditions that disable
9. the speaker R or headphones SELECT R Factory R default CH2 LEVEL OFF Selects embedded audio meter displayed by the on screen display METER ON CH SELECT 8CH Selects number of audio meter channels 4CH 2CH OdB POINT OFF Switches the 0 dB line displayed on the meter on and off ON CH INFO OFF Switches the channel displayed on the meter on and off ON 1 When ANALOG is selected in the INPUT SELECT menu the LEVEL METER does not indicate the audio level even when set to ON 32 Main Menu continued DISPLAY SETUP Underlined values indicate factory defaults Sub menu Settings Description WFM OFF Switches between WFM VECTOR waveform and vector display VECTOR WFM lt WFM gt Displays waveforms VECTOR lt VECTOR gt Displays vector waveforms POSITION LB Selects the position for the WFM VECTOR waveform display RB lt LB gt Left Bottom RT lt RB gt Right Bottom LT lt RT gt Right Top lt LT gt Left Top VECTOR x 8 Enlarges vector waveforms MODE x4 lt x 8 gt 8x x2 lt x 4 gt 4x x 1 lt x 2 gt 2x lt x 1 gt 1x VECTOR 100 Determines the scale of vector waveform SCALE 75 lt 100 gt Displays it at 100 scale lt 75 gt Displays it at 75 scale TIME CODE RU Turns the time code display on and off MODE LTC Selects time code display mode SELECT VITC lt LTC gt Displays linear time code LTC LUB lt VITC gt Displays vertical interval time c
10. 001 when GPI PRESET1 or GPI PRESET2 is selected with the GPI function 6 Display size for SD signals differ TYPE1 The effective horizontal area meets the SMPTE125M for NTSC and ITU R BT 601 5 for PAL TYPE2 The effective horizontal area meets the EIA RS170 for NTSC and ITU R BT 470 4 for PAL 18 Main Menu continued Marker types 16 9 marker Displayed for HD input and SD input in 16 9 ratio mode This marker is only displayed as a vertical bar The section becomes the MARKER BACK 4 3 marker 14 9 marker 13 9 marker VISTA marker CNSCO marker This marker is displayed as a horizontal dotted line VISTA marker CNSCO marker The marker is displayed as a vertical dotted line when UNDER is selected under SCAN in the VIDEO CONFIG menu M 4 3 marker Displayed for SD input in 4 3 aspect ratio mode This marker is displayed as a dotted line un 95 Area marker 7 b E 90 ea marker i a 80 Area marker Po e 93 Area marker 88 Area marker Displayed for HD input and SD input in 16 9 ratio mode This marker is displayed as a dotted line 95 Area marker 93 Area marker IES TYPE1 Vertical 89 horizontal 88 TYPE2 Ver
11. D input mode DVI COMP lt DVI VIDEO gt Selects component input lt DVI COMP gt Selects PC input 1 AUTO is the factory default but select a specific format when there is risk that the input signal may be contaminated by outside noise 30 Main Menu E COMP continued Selecting RGB COMP under YPsPr RGB in the INPUT SELECT menu opens the following menu Underlined values indicate factory defaults Sub menu Settings Description AUTOSETUP Selecting RGB COMP under YPsPr RGB in the INPUT SELECT menu automatically adjusts the screen A separate screen opens Select YES to perform AUTOSETUP H POSITION 0 60 Adjusts horizontal image display position Factory preset settings 30 V POSITION 0 60 Adjusts vertical image display position 2 Factory preset settings 30 PHASE 0 31 Adjusts the clock phase in 1 32 clock period increments Factory preset settings 16 CLOCK 700 1800 Adjusts the sampling clock in dot units 2 Factory preset settings WXGA XGA XGA Switches between WXGA and XGA WXGA RESET Returns H POSITION V POSITION PHASE and CLOCK settings in the COMP input compliant format to their factory defaults 1 EXECUTING is displayed during AUTOSETUP and COMPLETE appears when setup completes INCOMPLETE is displayed if setup could not be completed AUTOSETUP may no
12. ECT AUDIO DISPLAY SETUP CONTROL HOURMETER CONT BACK BACKLIGHT SUB WINDOW MENU POSITION STATUS DISPLAY SETUP LOAD SETUP SAVE POWER ON SETUP COLOR SPACE POWER SAVE MODE BLACK DATA INSERTION FUNCTION1 FUNCTION2 FUNCTIONS FUNCTION4 FUNCTIONS FUNCTION DISPLAY VIDEO NTSC SETUP YPsPr RGB COMPONENT LEVEL SELECT SYNC COMP DVI D INPUT SELECT EMBEDDED SELECT L EMBEDDED SELECT R LEVEL METER CH SELECT 0 dB POINT CH INFO CONTROL LOCAL ENABLE OPERATION LCD MARKER 16 9 GAMMA SELECT de FILM GAMMA ERR COLOR TEMP E SHARPNESS MODE NEEN SHARPNESS H GPI PRESET2 SHARPNESS V MARKER TYPE P MODE CROSS HATCH MONO USERO 63 ANAMO se SD ASPECT SCAN ci VAR1 WHITE BALANCE VAR1 VAR2 WHITE BALANCE VAR2 VAR3 WHITE BALANCE VAR3 GPI CONTROL GPI1 GPI2 GPI3 GPI4 GPI5 GPI6 GPI7 AUTOSETUP GPI8 H POSITION V POSITION PHASE CLOCK WXGA XGA RESET WFM VECTOR COLOR TEMP POSITION GAIN RED VECTOR MODE GAIN GREEN VECTOR SCALE WHITE BALANCE VAR1 3 GAIN BLUE TIME CODE BIAS RED MODE SELECT BIAS GREEN CLOSED CAPTION BIAS BLUE MODE SELECT RESET 17 Main Menu continued Underlined values indicate factory defaults Sub menu Setting Description MARKER OFF Enables the MARKER setting ON 16 9 23 OFF Selects and displays marker type for 16 9 aspect ratio 4 3 lt OFF gt No marker display 13 9 lt 4 3 gt 4 3 marke
13. FUNCTION GPI INPUT SELECT AUDIO DISPLAY SETUP CONTROL HOURMETER Xd4d dd dd 4 dd MENU EXIT MASEL ENTERENTER To return to the previous screen Push MENU 3 Press V A to select a sub menu and Press ENTER The settings in the sub menu change to green MARKER 4 3 OFF NORMAL OFF 95 16 9 95 16 9 GPI PRESET1 GPI PRESET2 MARKER TYPE TYPE1 CROSS HATCH OFF MENU EXIT MAJSEL ENTER SET 4 Press V A to select a setting then press ENTER To cancel press MENU MARKER 4 3 OFF NORMAL OFF 95 16 9 95 16 9 TYPE1 OFF GPI PRESET1 GPI PRESET2 MARKER TYPE CROSS HATCH MENU EXIT MASEL ENTER SET 15 User Data You can save and load up to five combinations of menu settings and adjustments made with the picture adjustment knob as user data You can also return settings and adjustments to their factory defaults User data include the following settings e Menu settings except SETUP LOAD SAVE including button function settings on the monitor front panel e Screen adjustments made with the picture adjusting knob Saving user data 1 Press MENU to display the MAIN menu 2 Press V A to select the SYSTEM CONFIG menu and press ENTER 3 Press V A to select the SETUP SAVE sub menu and press ENTER The setting in the sub menu changes to green SYSTEM CONFIG CONT BACK BACKLIGHT SUB WINDOW MENU POSITION STATUS DISPLA
14. Panasonic Broadcast BT LH1760P Menu Information How to Use the On Screen Menu The screen displays eight types of information input signal status picture adjusting knob status sharpness display FUNCTION display audio level meter display menu display time code display and closed caption display Input signal status 1 The selected input line gt page 9 El VIDEO SDI1 SDI2 SDI1 1080 59 941 YPsPr RGB VIDEO RGB COMP DVI VIDEO DVI COMP 2 Signal format e Use STATUS DISPLAY in the SYSTEM CONFIG menu to set the display status gt page 22 e UNSUPPORT SIGNAL appears if an unsupported signal is input It may also indicate that the format selected in the INPUT SELECT menu does not match the input signal e NO SIGNAL appears if no signal is input 3 Various indications PIXEL TO PIXEL mode e This indicates the PIXEL TO PIXEL mode is engaged 4 Various indications FILM mode e This indicates that GAMMA SELECT is set to FILM 5 Various indications lock status e This indicates that the control lock is on Note UNSUPPORT SIGNAL and NO SIGNAL may not be properly displayed Picture adjusting knob status Picture adjusting knob gt page 9 L e Press or turn this knob to make adjustments e The status display appears when the knob is pressed To clear the display press the knob again or leave it idle for 10 seconds e Only adjustments that
15. T METER OFF METER 2CH METER 4CH METER 4 3 16 9 8CH e SCAN e CROSS HATCH NORMAL SCAN UNDER SCAN CROSS HATCH HIGH CROSS HATCH LOW SUB WINDOW CROSS HATCH OFF SINGLE FULL PART STILL MONO e WFM VECTOR MONO ON MONO OFF WFM ON WFM VECTOR OFF VECTOR x 1 e TIME CODE VECTOR x 2 VECTOR x 4 VECTOR x 8 LTC VITC LUB VUB TC OFF e CLOSED CAPTION CC1 CC2 CC3 CC4 CC OFF E HV DELAY This displays the blanking period Each press of the button changes the display as follows H blanking display gt V blanking display gt H and V blanking display gt no blanking display E SUB WINDOW Opening the SUB WINDOW function splits the screen main window in two as shown below to enable comparison of a recorded still image with live video Use the SUB WINDOW setting FULL PART in the SYSTEM CONFIG menu gt page 22 to set up the function as shown below Press the button FUNCTION1 to FUNCTIONS gt page 23 to which the SUB WINDOW function has been assigned to turn the function on and off This assumes that the SUB WINDOW function has been assigned to any of the FUNCTION1 to FUNCTIONS buttons To setup IP MODE gt page 20 exit the SUB WINDOW function first FULL Resizes the main window to also display a second window two sub windows g Press the FUNCTION button to which the SUB WINDOW function has been assigned a Normal window Before image input After image input main window two sub w
16. Y SETUP LOAD BACKLIGHT FULL CENTER 38SEC OFF FACTORY gt POWER ON SETUP COLOR SPACE EBU POWER SAVE MODE OFF BLACK DATA INSERTION ON MENU EXIT MASEL ENTERJENTER Changes to green 4 Press V A to select a USER1 to USER5 file to save the settings to and press ENTER The following screen appears LAST SETUP SAVE USER1 YES gt NO MENUEXIT ASEL ENTER SET 5 Select YES and press ENTER This saves the user data To return to the previous screen Push MENU 16 Loading user data 1 Press MENU to display the MAIN menu 2 Press V A to select the SYSTEM CONFIG menu and press ENTER 3 Press V A to select the SETUP LOAD sub menu and press ENTER The setting in the sub menu changes to green SYSTEM CONFIG CONT BACK BACKLIGHT SUB WINDOW MENU POSITION STATUS DISPLAY gt SETUP SAVE POWER ON SETUP COLOR SPACE EBU POWER SAVE MODE OFF BLACK DATA INSERTION ON MENU EXIT VUSEL ENTERJENTER Changes to green 4 Press V A to select a USER1 to USER5 file to load and press ENTER The following screen appears To return to the factory defaults select FACTORY BACKLIGHT FULL CENTER 3SEC OFF USER1 LAST SETUP LOAD USER1 YES gt NO EXIT ASEL ENTERSET 5 Select YES and press ENTER This loads the user data Main Menu Menu configuration FUNCTION GPI INPUT SEL
17. abled PIXEL TO PIXEL When SD1 or SD2 is selected in the INPUT SELECT menu during 10801 P signal input or YPsPr is selected in YPsPr RGB 10801 P signal input is enabled When other settings are made INVALID FUNCTION appears to indicate that operation is disabled In SUB WINDOW mode INVALID FUNCTION appears to indicate that operation is disabled LEVEL METER When input is something other than SDI INVALID FUNCTION appears to indicate that operation is disabled MONO When GPI is set INVALID FUNCTION appears to indicate that operation is disabled TIMECODE When input is something other than HD SDI input INVALID FUNCTION appears to indicate that operation is disabled 24 Main Menu continued E Functions displayed during FUNCTION button operation Pressing any of the FUNCTION1 to FUNCTIONS buttons displays the operations assigned to each button as shown below e HV DELAY e MARKER DELAY OFF V DELAY H DELAY HV DELAY MARKER OFF 4 3 MARKER 13 9 MARKER 14 9 e AUTOSETUP MARKER VISTA MARKER CNSCO MARKER 95 AUTOSETUP COMPLETE INCOMPLETE NOT MARKER 93 MARKER 90 MARKER 88 RGB COMP CH MARKER 80 MARKER MARKER ON e BLUE ONLY e PIXEL TO PIXEL BLUE ONLY ON BLUE ONLY OFF e PIXEL POSITION GAMMA SELECT CENTER LEFT TOP LEFT BOTTOM RIGHT TOP GAMMA STANDARD GAMMA FILM GAMMA RIGHT BOTTOM PIXEL TO PIXEL OFF STDIO PST e AUDIO LEVEL METER SD ASPEC
18. d FILM GAMMA 2 VARICAM Selects type of FILM gamma mode OTHER lt VARICAM gt For VARICAM use lt OTHER gt Other COLOR TEMP USERO 63 Selects color temperature D93 lt USER 0 63 gt Adjustable settings 0 63 equivalent to a color a temperature range of 3 000 9 300K VARI lt D93 gt Equivalent to a color temperature of 9 300K VAR2 lt D65 gt Equivalent to a color temperature of 6 500K VAR3 lt D56 gt Equivalent to a color temperature of 5 600K lt VAR1 gt WB adjustment mode lt VAR2 gt WB adjustment mode 4 lt VAR3 gt WB adjustment mode SHARPNESS HIGH Selects the width of outline correction edge MODE LOW lt HIGH gt Thin edge lt LOW gt Wide edge SHARPNESS H 0 30 Sets horizontal outline correction The item display moves to the lower part of the screen during adjustment SHARPNESS V 0 30 Sets vertical outline correction The item display moves to the lower part of the screen during adjustment I P MODE MODE2 Selects IP conversion mode gt page 21 IP mode MODE1 lt MODE2 gt Inter field interpolation lt MODE1 gt Inter frame interpolation MONO 2 OFF Switches between color and monochrome MONO ON lt OFF gt Color lt ON gt Monochrome When ON the CHROMA setting of the picture adjusting knob is fixed at 0 ANAMO 27 OFF With an Anamo lens and SDI 720 60P 59 94P input the picture is ON resized to Anamo magnification the vertically enlarged signal can be vertically compressed and corrected for
19. display SD ASPECT 4 3 Sets the aspect ratio for SD signal input 16 9 lt 4 3 gt 4 3 display lt 16 9 gt 16 9 display SCAN NORMAL Sets under scan and normal display UNDER lt NORMAL gt Normal display lt UNDER gt Under scan 1 In split screen display changes are not reflected to the still image in the main window 2 These functions are not available when RGB COMP under YPsPr RGB or DVI COMP under DVI D is selected in the INPUT SELECT menu gt page 30 3 The following sharpness values are available and the settings for the selected input signal is displayed Adjustment status during selection appears at the bottom right of the screen 1 VIDEO system input VIDEO the factory defaults are SHARPNESS MODE LOW and SHARPNESS H V 0 2 HD for any other input the factory defaults are SHARPNESS MODE HIGH and SHARPNESS H V 0 3 SD for any other input the factory defaults are SHARPNESS MODE LOW and SHARPNESS H V 0 4 Selecting VAR1 VAR2 and VAR3 engages the WB adjustment mode gt page 21 5 To select USERO 63 1 Press ENTER USER changes to blue 2 Use V A to select 0 63 and press ENTER 6 To use the SUB WINDOW gt page 25 function 1 Change settings after exiting the SUB WINDOW function 2 It is recommended to use MODE2 for handling fast video 7 SCAN changes are not reflected in Anamo size display 20 Main Menu conti
20. ge display size to the input signal size ON Compatible formats 1080 601 591 501 60P 59P 50P 30P 29P 25P 24P 23P 24Psf 23Psf PIXEL POSITION CENTER Positions the display of signals in PIXEL TO PIXEL mode LEFT TOP lt CENTER gt Center of the screen RIGHT TOP lt LT gt Left Top RIGHT BOTTOM lt RT gt Right Top LEFT BOTTOM lt RB gt Right Bottom lt LB gt Left Bottom 1 The following settings are disabled in PIXEL TO PIXEL mode Setting ANAMO to ON and setting SCAN to UNDER in VIDEO CONFIG Any HV DELAY setting in FUNCTION MARKER display 2 Enabled during SDI1 SDI2 and YPsPr input E PIXEL POSITION display position sequence PIXEL POSITION 0 gt gt Q gt gt CENTER LEFT TOP RIGHT TOP RIGHT BOTTOM LEFT BOTTOM 27 Main Menu continued M CROSS HATCH The CROSS HATCH function enables display of markers at regular vertical and horizontal intervals to facilitate composition and other tasks The width of marker lines is 1 dot the markers consist of 1 line and are spaced 80 dots apart fixed value Each press of the button FUNCTION1 to FUNCTIONS5 to which the CROSS HATCH has been assigned turns the function on and off Each press of the FUNCTION button to which the CROSS
21. indows two sub windows Press the button again gt Still image Video Press the CE aa button again lt 2 a Video gt 25 Main Menu continued e PART Resizes the main window to show only its center to also display a second image two sub windows g Press the FUNCTION button to which the SUB WINDOW function has been assigned B Normal window main window E x gt D Sep S iet DOR Video Crops the image to show its center part Press the button again Before image input two sub windows mo esp 7 ID OB Video Video Press the button again The cropped main window image is placed side by side with a second image Note on FULL PART selection After image input two sub windows Video Still image These examples show 16 9 aspect ratio images This function is designed to enable comparison of identical formats input to the same input terminal Input of different formats via different input channels may distort the sub window left side still image or blanking could occur However input of an identical format signal to the input terminal during still image acquisition will display correctly M WFM VECTOR The WFM VECTOR function enables display of the waveform and vector display Use DISPLAY SETUP in the main menu to select WFM and
22. k engagement MAIN MENU mey Key mark gt y 2 Only available when REMOTE is selected under CONTROL HOURMETER Underlined values indicate factory defaults Sub menu Settings Description OPERATION XXXXXXH Displays the number of hours it has been on LCD XXXXXXH Displays the number of hours that the backlight has been on 3 XXXXXX indicates the number of hours XXXXXX 262800H about 30 years 262800 or greater number results in OVER 34
23. nued IP mode within 1 field The factory default is MODE1 MODE performs IP conversion using inter field interpolation Since interpolation is performed inside each field this mode is suitable for checking interlace status MODE1 performs IP conversion using inter frame interpolation Conventional inter frame interpolation involved 1 frame or greater delay but this monitor suppresses the delay to E WB adjustment mode Select VAR1 to VAR3 for COLOR TEMP in the VIDEO CONFIG menu to make WHITE BALANCE VAR1 to WHITE BALANCE VAR3 WB adjustments Underlined values indicate factory defaults Sub menu Settings Description COLOR TEMP USERO 6 Selects the color temperature that will become the basis D93 for adjustment D65 lt USER 0 63 gt Adjustable settings 0 63 equivalent to a D56 color temperature range of 3 000 9 300K lt D93 gt Equivalent to a color temperature of 9 300K lt D65 gt Equivalent to a color temperature of 6 500K lt D56 gt Equivalent to a color temperature of 5 600K GAIN RED 0 1023 Adjusts the GAIN elements for RED 2 GAIN GREEN Factory defaults are color Adjusts the GAIN elements for GREEN temperature lt D65 gt GAIN BLUE values Adjusts the GAIN elements for BLUE These are the adjustments made before shipment from the factory BIAS RED 512 511 Adjusts the BIAS elements fo
24. ode VITC VUB lt LUB gt Displays user bits included in LTC lt VUB gt Displays user bits included in VITC r tes ac Turns closed caption display on and off 2 MODE CC4 Selects the cross caption display mode 2 SELECT CC3 CC2 CC1 1 Available during HD SDI input signals 2 Available during VIDEO NTSC input Closed captions appear as bright lines on line 21 when closed caption is set to ON and underscan is also on 3 Opens the vector display during SDI signal input 33 Main Menu continued CONTROL Underlined values indicate factory defaults Sub menu Settings Description CONTROL LOCAL Selects operation with control clock REMOTE lt LOCAL gt Enables front panel operation lt REMOTE gt Enables remote operation front panel operation is locked LOCAL DISABLE Selects the disabled operation on the front panel when selecting ENABLE 2 INPUT REMOTE under CONTROL lt DISABLE gt Disables all front panel operations lt INPUT gt All controls except INPUT SELECT and the volume knob are disabled 1 The menu can be displayed when the lock is engaged Only CONTROL LOCAL ENABLE menu items are available when the lock is engaged The picture adjusting knob is disabled when the lock is engaged The LOCAL ENABLE setting determines operations in lock mode The volume knob gt page 9 El can be used during lock engagement The key mark is displayed during loc
25. operation HV DELAY During SUB WINDOW WFM PIXEL TO PIXEL mode operation INVALID FUNCTION appears to indicate that operation is disabled When RGB COMP is selected under YPsPr RGB or DVI COMP is selected under DVI D in the INPUT SELECT menu INVALID FUNCTION appears to indicate that operation is disabled AUTO SETUP When something other than RGB COMP is selected under YPsPr RGB in the INPUT SELECT menu NOT RGB COMP CH appears to indicate that operation is disabled When RGB COMP is selected under YPsPr RGB in the INPUT SELECT menu and no signal is input INCOMPLETE appears to indicate that operation is disabled GAMMA SELECT When GPI is set INVALID FUNCTION appears to indicate that operation is disabled When RGB COMP is selected under YPsPr RGB or DVI COMP is selected under DVI D in the INPUT SELECT menu INVALID FUNCTION appears to indicate that operation is disabled SD ASPECT When GPI is set INVALID FUNCTION appears to indicate that operation is disabled During SUB WINDOW still image and HD display including PIXEL TO PIXEL INVALID FUNCTION appears to indicate that operation is disabled SCAN When GPI is set INVALID FUNCTION appears to indicate that operation is disabled During SUB WINDOW and PIXEL TO PIXEL mode operation INVALID FUNCTION appears
26. r lt 13 9 gt 13 9 marker 14 9 lt 14 9 gt 14 9 marker lt CNSCO gt CNSCO marker CNSCO lt VISTA gt VISTA marker lt 95 gt 95 area marker VISTA lt 90 gt 90 area marker lt 80 gt 80 area marker 95 lt 93 gt 93 1 area marker TYPE1 93 93 area marker TYPE2 90 lt 88 gt 89 5 area marker TYPE1 88 88 area marker TYPE2 80 4 3 24 OFF Selects and displays marker type for 4 3 aspect ratio 95 lt OFF gt No marker display 93 lt 95 gt 95 area marker lt 93 gt 93 area marker 90 lt 90 gt 90 area marker lt 80 gt 80 area marker 88 lt 88 gt 89 area marker TYPE1 80 88 area marker TYPE2 BACK NORMAL Selects the background brightness around the marker HALF lt NORMAL gt Normal background BLACK lt HALF gt 50 background brightness lt BLACK gt 0 background brightness black CENTER OFF Displays the center marker ON lt OFF gt Turns the display off lt ON gt Turns the display on GPI PRESET1 4 3 GPI PRESET1 Selects the marker displayed by the GPI terminal 13 9 MARKER1 ON OFF gt page 36 operation 14 9 GPI PRESET2 Selects the marker displayed by the GPI terminal CNSCO MARKER2 ON OFF gt page 36 operation VISTA lt 4 3 gt 4 3 marker 5 95 16 9 lt 13 9 gt 13 9 marker GREPRESETS 93 16 9 lt 14 9 gt 14 9 marker 90 16 9 lt CNSCO gt CNSCO marker 88 16 9 lt VISTA gt VISTA marker 80 16 9 lt 95 16 9 gt 95 area marker for 16 9 aspect ratio 95 4 3
27. r RED 2 BIAS GREEN Factory darau o Adjusts the BIAS elements for GREEN 2 BIAS BLUE Adjusts the BIAS elements for BLUE 2 RESET Resets GAIN RED BIAS BLUE to color temperature values selected under COLOR TEMP 1 Selecting COLOR TEMP and pressing ENTER after making a change opens a confirmation screen Selecting YES and pressing ENTER in this screen resets selected GAIN and BIAS values to the selected color temperature values 2 The item display moves to the lower part of the screen during adjustment 21 Main Menu continued SYSTEM CONFIG Underlined values indicate factory defaults Sub menu Settings Description CONT BACK BACKLIGHT Selects function to be assigned to CONTRAST BACKLIGHT front panel CONTRAST knob lt BACKLIGHT gt Adjusts the BACKLIGHT lt CONTRAST gt Adjusts the CONTRAST BACKLIGHT 0 60 Adjusts LCD backlight brightness Adjust as reguired by ambient conditions SUB WINDOW FULL Selects sub window type PART lt FULL gt Reduces the entire images for both input signals and places them side by side lt PART gt Cuts out the center of the images for both input signals and places them side by side the images are shown at their original size MENU CENTER Positions the on screen menu POSITION LB lt CENTER gt Center of the screen a lt LB gt Left Bottom lt RB gt Right Bottom LT lt RT gt Right Top lt LT gt Left Top
28. s indicate factory defaults Sub menu Settings Description VIDEO AUTO Selects the video input format NTSC lt AUTO gt Automatically selects NTSC or PAL PAL lt NTSC gt NTSC lt PAL gt PAL NTSC SETUP 75 Selects NTSC setup level 00 lt 75 gt Select this function when using 7 5 setup signals Adjusts the interior of the monitor to the 7 5 setup level to suit the black level lt 00 gt Select this when there is no setup signal YPsPr RGB YPsPr Selects YPsPr component or RGB input mode RGB VIDEO lt YPsPr gt Selects the YPsPr signal RGB COMP lt RGB VIDEO gt Selects the video RGB signal lt RGB COMP gt Selects the PC RGB signal COMPONENT SMPTE Selects YPsPr component signal input level LEVEL B75 lt SMPTE gt Signal level complies with SMPTE and Ps and Pr are Boo 0 7 Vp p at 100 chroma lt B75 gt Select this when connecting a Betacam or similar device with a setup function Adjusts the interior of the monitor to the 7 5 setup level to suit the black level lt B00 gt Select this when connecting a Betacam or similar device without a setup function SELECT SYNC INT Selects the sync signal when using YPsPa and RGB VIDEO input EXT lt INT gt Select when the synchronizing signal is superimposed on the G or Y signal lt EXT gt Select to synchronize with an external synchronizing signal COMP v Performs analog PC settings COMP gt page 31 DVI D DVI VIDEO Selects DVI
29. t provide adequate adjustment for some video input Use H POSITION V POSITION PHASE and CLOCK to adjust 2 Each input format can be adjusted but not when user data is loaded SETUP LOAD gt page 22 or saved SETUP SAVE gt page 22 3 CLOCK factory default FORMAT CLOCK FORMAT CLOCK 640 x 400 70 Hz 800 1024 x 768 60 Hz 1344 640 x 480 60 Hz 800 1024 x 768 70 Hz 1328 640 x 480 75 Hz 840 1024 x 768 75 Hz 1312 640 x 480 85 Hz 832 1024 x 768 85 Hz 1376 800 x 600 60 Hz 1056 1280 x 768 50 Hz 1648 800 x 600 70 Hz 1040 1280 x 768 60 Hz 1680 800 x 600 75 Hz 1056 1280 x 768 75 Hz 1712 800 x 600 85 Hz 1048 1280 x 1024 60 Hz 1688 31 Main Menu continued Sets speaker and headphones output Underlined values indicate factory defaults Sub menu Settings Description INPUT AUTO Selects speaker and headphones output SELECT ANALOG lt AUTO gt When an SDI input line is selected with the INPUT SELECT button on the front panel embedded audio SDI terminal When input lines other than SDI1 or SDI2 are selected with the INPUT SELECT button on the front panel analog AUDIO input terminal lt ANALOG gt Analog AUDIO input terminal EMBEDDED CH1 CH8 Selects embedded audio channel output to the speaker L or headphones SELECT L Factory L default CH1 EMBEDDED CH1 CH8 Selects embedded audio channel output to
30. tical Horizontal 88 L VISTA marker Area marker CNSCO marker This marker is displayed as a dotted line TYPE1 Vertical 93 1 horizontal 93 TYPE2 Vertical Horizontal ane 95 Area marker 93 Area marker TYPE1 Vertical 89 5 horizontal 88 TYPE2 Vertical Horizontal 88 90 Area marker 80 Area marker 88 Area marker 90 Area marker 80 Area marker 88 Area marker You can display the 4 3 marker and the 16 9 marker simultaneously Simultaneous display example The section becomes the MARKER BACK It controls the background of the marker selected with a 16 9 ratio 4 3 marker 16 9 marker E Center marker 7 ji 16 9 marker 95 area marker 4 3 marker 80 area marker Center marker This marker is displayed at the center of the screen Main Menu continued VIDEO CONFIG Underlined values indicate factory defaults Sub menu Settings Description GAMMA STANDARD Selects gamma curve SELECT FILM lt STANDARD gt Standard mode lt FILM gt Film mode STDIO PST lt STDIO PST gt Color emphasis mode a mode that approximates CRT display capability suitable for studio or postproduction application The F ILM mark appears at the top left of the screen when FILM is selecte
31. to indicate that operation is disabled SUB WINDOW When RGB COMP is selected under YPsPr RGB or DVI COMP is selected under DVI D in the INPUT SELECT menu INVALID FUNCTION appears to indicate that operation is disabled If you select RGB COMP or DVI COMP while motion picture is displayed in sub window the screen returns to a single screen display Selecting something other than RGB COMP or DVI COMP opens the split screen mode and a still image is blacked out WFM VECTOR During SUB WINDOW and PIXEL TO PIXEL mode operation INVALID FUNCTION appears to indicate that operation is disabled When RGB COMP or RGB VIDEO is selected under YPsPr RGB or DVI COMP or DVI VIDEO is selected under DVI D in the INPUT SELECT menu INVALID FUNCTION appears to indicate that WFM operation is disabled 1080 23P 24P 25P 29P or 30P input causes INVALID FUNCTION to appear indicating that operation is disabled VECTOR does not appear when a selection other than SDI is made in the INPUT SELECT menu MARKER When RGB COMP is selected under YPsPr RGB or DVI COMP is selected under DVI D in the INPUT SELECT menu INVALID FUNCTION appears to indicate that operation is disabled When GPI is set during sub window operation INVALID FUNCTION appears to indicate that operation is dis
Download Pdf Manuals
Related Search