Palsonic 6845PFST User's Manual
Contents
1. menu item select VOL volume adjust menu item adjust To turn off TV automatically OFF timer K With the OFF timer the TV will automatically switch to standby mode at a preset time 1 In Timer menu press CH to select Timer off 2 Use Digit Buttons to set the OFF time In wrong in inputting press RED button to cancel and input again At the preset time the TV will go into standby mode automatically Palsonic Once the OFF timer has been fulfilled next when you want to use it you should reset it again To exit the menu press OK button 21 Timer setting To turn on the TV automatically ON timer D With the ON timer the TV will automatically turn on to a A F On standby preset channel at a preset time L 1 In Timer menu press CH to GS 3 select Timer on 2 Use Digit Buttons to set ON time If wrong in inputting Timer on press RED button to cancel i Prog no and input again lt A 3 Press CH to select Prg no use VOL to set the ON program or you can directly input the number by digit buttons MENU 4 Press STANDBY C button to switch the TV to standby mode CH At the preset time the TV will turn on to the preset menu item select program automatically VOL Once the ON timer has been fulfilled next when you want volume adjust ve item adjust to use it again you should reset it OK exit the menu To switch the TV to a progr2. channel 28 Automatic tuning Manual tuning 2 Press MENU repeatedly to display Tuning menu lt A Digit buttons 3 Press CH to select Manual tuning press VOL to enter into Manual Manual tuning MENU tuning sub menu A CH 4 lt a gt menu item Press CH to select Fine select tune Manual tuning VOL volume adjust 5 S menu item adjust Press VOL to begin fine OK tuning until the best possible Fine Tune exit the menu picture and sound are obtained Palsonic To exit the menu press OK button 14 Setting Colour System lf some channel s colour is abnormal it may be that the setting of the colour system is wrong please do the following steps to set a proper colour system 1 Press MENU repeatedly to display Special functions menu Color system Auto 2 Press CH to select Color lt Ap system 3 Press VOL to select a proper colour system MENU CH Setting Sound System menu item select If some channel s sound is abnormal it may be that the VOL setting of the sound system is wrong please do the MEA acs following steps to set a proper sound system OK exit the menu 1 Enter into Special functions menu 2 Press CH to select P Sound system 3 Press VOL to select a Sound system B G proper sound system lt 44 Some models are only with one sound system and in this Palsonic case the Sound System does not need to be adjus
3. OK exit the menu 2 Press CH or CH to select Adjusting sound 1 Press MENU repeatedly to display Sound menu Volume desired adjusting item Bass Treble S M y Sound mode select gm 6 3 Press VOL to adjust the ere level nec Volume stronger Bass stronger Treble stronger h Sound mode selection Balance decrease the decrease the right channel left channel You can select the sound quality instantly among DBE Dynamic three preset modes and one user set mode bass N ON OFF Press the S M button to select Sourd mode Movie MSS Micronas ON OFF the desired sound quality Movie surround sound Music Speech and Favourite sowa mode musc user set can be selected soun a Speech cyclically eh e Fawori Note DBE MSS function are optional function The adjusted level is stored in the Favourite position Sound quality Movie like a movie theatre filled with a dynamic sound Music like a music hall filled with a rich warm sound Speech Suitable for listening to news dialouge Favourite the sound quality you set 19 Sound Controls The unit receives both stereo and bilingual broadcasts transmitted in either the NICAM or German stereo bilingual broadcast system Stereo Programs 12 1 When a stereo program is Auto B G received STEREO appears Mono Enter into earphone state 12 2 Press the SOUND button to select Auto B G the stereo monaural mode Mono Bilingual Program
4. S VIDEO terminal To connect the 21 Pin Scarts External equipment connections This TV set is equipped with 21 Pin Scarts for your desired equipment to be connected The figure below shows how to connect the AV1 SCART to video equipment To access the unit connected to AV1 SCART press the 0 AV button until AV1 appears on the screen 21 pin SCART connector 4 If the signal source is RGB signal the OSD will be AV1 5 i 4 RGB Cal Z 21 pin SCART Converter Note If the equipment you want to connect is not equipped with 21 pin Scart you can connect it by using the 21 pin Scart Convertor supplied as illustrated above The figure below shows how to connect the AV2 SCART to video equipment AV2 SCART press the 0 AV button until AV2 appears on the screen 21 pin SCART connector If the signal source is RGB signal the OSD will be AV2 21 pin SCART RGB Converter Note If the equipment you want to connect is not equipped with 21 pin Scart you can connect it by using the 21 pin Scart Convertor supplied as illustrated above To connect
5. confirm Now program 23 and program 37 are swapped Palsonic To exit the menu press OK button Repeat the above steps to edit the programs in your favourite order 16 Channel selection 1 Use Direct Channel Select buttons To select one digit channel Press button to display then input the number button i Press 0 9 button 5 To select two digit channel Press button to display then input the number Digit buttons Press Press Press button p 0 9 button 5 0 9 button 56 To select three digit channel Press button to display then input the number CH Channel i i a u p d own Press Press Press Press button 0 2 button 0 9 button 0 9 button In this model the maximum channel number is 255 2 Use CH or CH button Press CH button the channel number increases Press CH button the channel number decreases Retain on screen display 3 Use previous program button Press this button to switch between the current program Palsonic and the previous one Notes Use on screen display button to know the current channel number Press this button to display the 12 current TV state If in TV program Auto B G viewing then it will display the current channel number colour system sound system and sound mode Press it again to cancel the display 17 Picture adjustment To select the picture mode You can select
6. have sections that are concealed such as the answers to riddles or puzzles To see the concealed part press the button Press it again to conceal 5 HOLD To hold the current teletext page press the button To release the page press the button again 6 SIZE Press the button to expand the top half of the display Press it again to expand the bottom half of the display Press it once more to resume normal size 7 REAL CLOCK Press the button to display the real time on the screen while viewing TV program which carries a teletext broadcasting Press again to turn off the time display 8 RED GREEN YELLOW CYAN buttons corresponds to GAMES S M P M LOCK button These four colour coded buttons control a memory that allows instant access to the displayed corresponding page number 9 34 buttons Press the buttons to adjust Teletext brightness 10 buttons Press the buttons to adjust Teletext contrast 2 Special Functions Before calling service personnel please check the following chart for a possible cause to the trouble you are experiencing Symptoms Check the following items Power is not turned on O Be sure the power cord is plugged in Poor colour poor tint o Contrast colour tint are not correctly adjusted Spots appear on the screen o Possible interferences of automobiles motorcycle trolley bus neon lamps etc Stripes appear on the screen Possible interference of electronic interference
7. lock function is active now the screen only displays blue back with Lock menu bar 4 To unlock input the correct password to set the Child lock to OFF Note the preset password can be changed the steps are shown below After you set the lock to On or Off the screen will display New Inout the new password and confirm again Now the password has been changed But make sure to remember the new password In child lock OFF mode if you press LOCK button unintentionally you can press OK button to exit In child lock ON mode buttons on the TV set can not act Also most buttons on the remote control can not act To avoid forgetting the password write it down here 24 Hotel lock setting Hotel lock is an optional function Hotel lock setting Making use of hotel lock function you can limit some functions so that other user can not change your settings This function is especially useful in hotel 1 Press 3t button on the Hotel remote control the screen will display Hotel me Hotel HK KK 2 Input the 6 digit password the preset password is 123465 the screen will display Hotel Off or On Hotel On 3 Press VOL to select ON Hotel Off Now Hotel Lock function is active now Only some buttons for example channel select buttons volume control buttons AV button etc can act and the volume is limited In Hotel ON mode the maximum volume level is the level you set just
8. normal when you adjust the CONTRAST or BRIGHTNESS setting CARE AND MAINTENANCE To prevent fire or shock hazard disconnect your unit from the AC power source when cleaning The finish on the receiver may be cleaned with a dust cloth and cared for as other furniture Use caution when cleaning and wiping the plastic parts Mild soap and a soft damp cloth may be used 29 Specifications Power Supply AC 240V 50Hz Power Consumption 180W Dimensions mm 800 W x 595 H x 511 D Weight kg 47 CRT 68cm TV system amp channel range System VHF UHF CATV PAL B G 2 12 21 69 X Z 2 1 S41 TELETEXT WST TELETEXT Colour System PAL BG NTSC AV Stereo bilingual system NICAM BG IGR BG Sound output 7WX 2 Note Design and specifications are subject to change without notice 30 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL 02 9313 7111 FAX 02 9313 7555 www palsonic com au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA 1300 657 888 604 TA29513 00
9. not preset the desired channels or you want to preset the desired channels one by one with the preferred channel numbers please make use of Manual tuning 1 Repeatedly press MENU to enter into Tuning menu Manual tuning Press CH or CH to select Manual tuning qe Press VOL to enter into Manual tuning submenu Manual tuning Aa GW N Program In Manual tuning submenu MENU press CH to select Program use VOL to E CH select a number or you can KAN valet tem directly input the number by O digit buttons a ren ech al 5 Pica ee psi anual search press Mania h a oe VOL to start searching tae gt eeer The VOL searches towards E lower frequency the VOL lt A gt towards higher frequency When a channel is located the searching stops and the channel is stored in the specified position number Notes 7 In manual tuning you can also use BAND selection to quicken searching process if Palsonic you know which band your desired program locates in The band switches among VHF L VHF H and UHF 2 Repeat the above 1 5 steps if you want to store another program in other position number To exit the menu press OK button 13 Fine tuning is not necessary under normal conditions However in area of inferior broadcast conditions where adjustment is necessary for a better picture and sound use Fine tuning 1 Select a channel you want to fine tune for example
10. teletext signal Channel swap Child lock option Hotel lock option Digital comb filter SMV scan velocity modulation option Black stretch CTI Colour Transient Improver function Game AVL automatic volume level option Bass Treble Balance control MSS Micronas surround sound option DBE Dynamic Bass Enhanced option Picture rotate option Safety precautions Note This TV set can operate on an AC power of 240V 50Hz You must not use a power supply of any other type When any unusual situation occurs turn off the power supply at once and remove the plug from the wall outlet Contact a qualified service department in your local area Do not expose the TV set to rain or excessive moisture Avoid using the set in very warm or damp places and never use it in a bathroom When cleaning dust off the picture tube disconnect the power first You can wipe lightly with a piece of dry clean and soft cloth Avoid exposing the set to direct sunlight and other sources of heat to prevent damage to the cabinet and components O High voltage exists in this TV set Do not remove the cover Safety precautions Do not cover the ventilating hole in the cabinet Keep a space of more than 10cm from the walls to the TV set to ensure adequate ventilation If the power cord or the plug is damaged contact a qualified service department for service O When the TV set is to be left unattended for a long p
11. the AV Outputs You can connect a stereo system to the AV output jacks on the TV set rear to enjoy a high quality sound from the stereo system or you can connect the AV output jacks to the VTR to record the program you like To external input Eo Signal Swoim L Ce en C _ amp Stereo System Y Yellow video WW White audio L MONO a VTR for recording R Red audio R 2 vol m gt e o J nme Power on off Turning on 1 Press the Power Switch on the TV set Now the standby indicator lights up the TV set is in STANDBY mode Now please follow step 2 2 In STANDBY mode press the button or 0 9 digit button on the remote controller and the TV set is turned on 0 9 digit In STANDBY mode you can also press Channel buttons up down or AV TV button on the set to turn on the set Turning off 1 Press the Power Switch on the TV set if you want to cut off the power completely If you want to turn off the TV set temporarily press the button Palsonic 10 Channel delete amp to order the channels Watching AV program This TV set provides AV input terminals and 21 pin scarts for your convenient connection to VCR DVD or other video equipments 1 To wa
12. the picture quality instantly among three preset modes and one user set mode Poure mode Standart mode Standard Press the P M button to select the Pitre mode Dynamic desired picture quality Standard Dynamic Mild and Favourite user Picture mode Mild set can be selected cyclically Picture mode Favourite Mode Picture quality Standard Display normal pictures Display more brightness and contrast pictures MENU CH menu item select VOL volume adjust z L jain adjust Picture adjustment OK exit the menu 1 Press MENU to display P M Picture menu Picture mode select Display mild pictures The picture quality you set Contrast 2 Press CH or CH to select desired adjusting item 3 Press VOL to adjust VOL Contrast weaker Brightness darker Colour paler Palsonic Sharpness softer Tint purplish SVM High Mid Low Off Notes Tint is only for NTSC system Turning on SVM will greatly improve picture s sharpness SVM is an optional function To exit the menu press OK button 18 Sound controls Adjusting volume 1 Use VOL or VOL button Press VOL button the volume increases Press VOL button the volume decreases Poe 2 Use MUTE button If you want to mute the sound press IQ button on the remote To resume the sound press this button again MENU CH menu item select VOL volume adjust menu item adjust
13. OWNER S MANUAL Paisonic 68CM CORDLESS REMOTE COLOUR TELEVISION MODEL 6845PFST Type Tested Electrical Safety AS NZS 3250 Lic 4166 Standards Australia APP No N15900 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL 02 9313 7111 FAX 02 9313 7555 www palsonic com au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA 1300 657 888 Congratulations on your purchase of this Palsonic colour television We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this equipment Retain this manual in an easily accessible location for future reference Screen displays and illustrations in this manual may differ from the actual ones for better visibility Contents Fea CS a 1 Channel Selection 05 17 Safety precautions 008 2 Picture adjustment 18 Identification of Controls 4 to select the picture mode 18 POM oenen a 4 Picture adjustment ccccceeeeeeeees 18 Eee GRE EEEE S 4 Sound Controls cccee 19 Remote Controller lcnn 5 Adjusting VOIUME nsee 19 Antenna Connection 6 Sound mode selection cc 19 Installation cssesssesseeseneeees 7 To select stereo bilingual mode 20 External equipment To enter into earphone state 20 COMME CUONS cicin 8 Timer Setting ousus 21 Using the side Audio Vid
14. Reception disturbances Most types of television interference can be remedied by adjusting the height and position of the VHF UHF antenna Outdoor antennas are recommended for best results if not using cable The most common types of television interference are shown below If one of these symptoms appear when the TV is connected to a Cable TV system the disturbance may be caused by the local cable company broadcast IGNITION Black spots or horizontal streaks may appear picture may flutter or drift Usually caused by interference from automobile ignition systems neon lamps electric drills and other electric appliances GHOSTS Ghosts are caused by the television signal following two paths One is the direct path and the other is reflected from tall buildings hills or other objects Changing the direction or position of the antenna may improve the reception SNOW 5 Ee n If your receiver is located in the fringe area of a television station where the f 9 3 ad signal is weak your picture may be marred by the appearance of small dots 4334 i SE LEN When the signal is extremely weak it maybe necessary to install an ea ere cae iat external antenna to improve the picture lt a ade ee sag SAS h ht rere z RADIO FREQUENCY INTERFERENCE This interference produces moving ripples or diagonal streaks and in some cases causes loss of contrast in the picture PICTURE SIZE VARIATION A slight picture size variation is quite
15. am at a preset time Cancel the inputting 1 In Timer menu press CH to select Timer set 2 Use Digit buttons to set the time If wrong in inputting press RED bution to cancel and input again Timer set 18 00 lt 4 3 Press CH to select Prg no use VOL to set a program number or directly input the Palsonic number by digit buttons At the preset time the TV will Prog no automatically switch to the preset program Note When you turn off the TV by main power switch all functions in Timer menu will be cancelled To exit the menu press OK button 22 Special functions To select OSD language There are multi OSD languages in this TV set provided for you to select OSD on screen display 1 Press MENU repeatedly to display Special functions menu Special functions 2 Now the first menu item is Language English highlighted and indicates the current selected OSD language if in English it will display ENGLISH lt gt 3 Press VOL to select a proper OSD language Setting blue back 1 Enter into Special functions menu Special functions MENU CH4 2 Press CH to select Blue Be pee menu item back select VOL 3 Press VOL to turn on off volume adjust blue back menu item adjust If the Blue back is turned on the TV will appear a blue back OK on the screen when there is no input signal exit the menu Rotate function When you switch on your TV th
16. before you enter the Hotel ON mode If you a Clear the OSD See want to change the volume limitation set the Hotel to OFF and then adjust the volume then enter into ON mode N l VOL buttons again To exit the hotel lock set Hotel to OFF To clear the On screen display you can press OK button o gt o Enter into hotel lock settino To change Hotel Lock password The preset password for hotel lock can be changed the steps are shown below Hotel ______ 1 After setting Hotel to OFF mode press MENU button the screen displays Hotel se e se se e _ New Palsonic Hotel Off 2 Input the new Password and confirm N again pe eae Now the password has been changed 25 Game playing To play game card game 1 Press GAME button to enter 2 Press MENU button to select level There are five levels for you to select The higher the level the more difficulty the playing 3 Press CH CH VOL VOL button to select card press OK button the card will be turned over If the second card you turned over is different with the first card it will cover again unless the same two cards are selected Only you turn over all the cards you win the game 4 Press GAME button to exit The best record The level you select Game Best 190 i l ime 120 Fi ty Game control buttons i a HF a Cea P iy cae ae i 7 a Enter exit game playing The card you turn over Palsonic To
17. eo jacks 8 Setting ClOCK eresia 21 to connect the 21 Pin scarts 9 Setting OFF time aeee 21 To connect the AV outputs 9 Setting ON timer screen 22 Power on off ccsscsessscueeneeseees 10 Setting Timer Set ccceceee eee 22 TUNING On ccscentsensecvesvcesscnecevescetescsst 10 Special functions 23 Turning Off s ncidaictindedusinetradsoouavantetints 10 To select OSD language 23 Selecting Input Signal 11 Setting blue back seeen 23 Watching AV program soesnesennoennn 11 Rotate TUNG ON virunn isen 23 Switching from AV to TV eeen 11 Screen aspect selection 00 23 T NINO Menonin 12 Child lock setting 24 Automatic tuning seese 12 Hotel Lock Setting 25 Manual Tuning oneen 13 Game playing cceeee 25 Fine tuning ooo ee eee eee eee seen seen 14 Teletext eee ee ne 27 Setting colour System ccceeee 15 Troubleshooting Guide 28 Setting sound system s e 15 Specifications eee 30 Channel delete 008 16 To order the channels 16 Main features Hyperband Automatic channel preset Full function remote control 21 pin scarts and AV input output RCA jacks Selectable picture and selectable sound NICAM and German stereo bilingual broadcasts optional Teletext ON Timer OFF Timer Real Clock with
18. ere may be a slight tilt of the picture to the left or right This is due to the earth s magnetic field or position of your TV To rectify you can do the following 1 Enter into Special functions menu Special functions 2 Press CH to select Rotate Rotate 3 Press VOL to rotate the picture until you are satisfied Palsonic 2 Press CH to select To exit the menu press OK button Aspect 3 Press VOL to select picture size ratio between 4 3 and 16 9 according to your preference 23 Child lock setting Digit buttons MENU CH menu item select VOL volume adjust menu item adjust OK exit the menu Enter into child lock setting Palsonic Child lock is an optional function Child lock setting Making use of child lock function you can lock all the programs to prevent children from viewing them 1 Press LOCK button on the Lock ______ Lock _ remote control the Lock menu bar appears Lock KKK Lock KK or press MENU repeatedly 0 5 me to display Special functions o tox or menu Press CH to select New ______ Child lock item then press VOL to enter NO Input the correct password 6 digit the preset password Is 123456 After inputting the screen displays Lock On OO After one or more seconds the screen will display New now press OK button or wait for some time until New disappear and the child
19. eriod of time turn off the power supply and remove the plug from the wall outlet gt Don t try to push anything into the cabinet or place any vessel with water on the TV set amp Don t overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock Identification of Controls Volume up Volume down Remote sensor Channel up Channel down AV TV Menu POWER switch AV3 input S VHS input S VIDEO VIDEO AUDIO L MONO R S VIDEO VIDEO L MOMO AUDIO R C3AV3 SVHS Earphone jack Antenna input OOOOOOOOOO ea Ig A OOOOOOOOoOO AV output VIDEO AUDIO L MONO R Identification of Controls Real clock teletext Power on standby Hold teletext Reveallconceal teletext Size teletext Mix teletext Index teletext Teletext TV Sound mute Enter into Earphone state Direct channel select TV VIDEO input select Previous program Digit select SAW ac Return to TV mode Clear the menu Channel up down D Volume up down MENU Menu item select a Menu item adjust Red teletext Game playing Gan Coc CYAN teletext Child lock GREEN teletext G C YELLOW teletext Sound mode select E gt Picture mode select fo Contrast control teletext Brightness control teletext Sound Stereo Mono Bilingual select Retain on screen display Palsonic Antenna connection Optimum reception of colour requires a good si
20. exit the menu press OK button 26 Teletext Teletext is an optional function therefore only a set with the teletext system can receive the teletext broadcast Real clock Reveal Conceal Mix Text select Direct page select Coloured text select Text page up down Teletext Teletext contrast control brightness control Palsonic Switching Teletext on off Press button once to switch on teletext Press button twice both teletext and TV program are displayed Press button third time to switch off the teletext Description of Teletext Teletext is a free service broadcast by most TV stations which gives up to the minute information on news weather television programs share prices and many other topics The thing to remember about Teletext is that it is slow It is the nature of the system itself where a large amount of information is sent using a small fraction of the TV signal If you get yourself into trouble read the following instruction carefully It may have your answer Teletext is controlled through the remote controller Button introduction 1 TEXT Press amp button to bring the set from TV mode to Teletext mode Press it at the third time to resume TV mode 2 MIX Press the button the text will be superimposed on a TV picture Press again to restore text 3 INDEX In teletext mode press the button the index page will appear 4 REVEAL Some pages
21. from another TV set a computer an electronics game machine a broadcast station etc Double images or ghosts This may be caused by reflections from nearby mountains or buildings Check the antenna direction Snowy picture It is possible that the aerial lead in is damaged or comes off Check the antenna direction The set may be in child lock ON mode Use LOCK button and password to unlock it If you forget the password you can contact our company or the The screen only displays blue back Buttons on the TV set can not act dealer Only some buttons have function while others can not act and the volume is limited The set may be in hotel lock ON mode Set hotel lock to OFF If you forget the password you can contact our company or the dealer Even if the picture or the sound is normal changes in the room temperature sometimes make the TV cabinet expand or contract making a noise This does not indicate a malfunction TV cabinet creaks Remote controller does The batteries may be worn out not work The batteries may be installed with their polarity reversed O When the set is switched on do not shift or move the set around Sometimes it may develop an Unevenness in colour in unevenness in colour in some parts of the screen some parts of the screen This can be eliminated by switching off the set with the POWER switch and wait for 30 minutes before Switching on again 28 Toubleshooting Guide
22. gnal and will generally mean that an outdoor aerial must be used The exact type and position of the aerial will depend upon your particular area KN O Notes 0 t is recommended that the 75 ohm coaxial cable be used to eliminate interference and noise which may occur due to radio wave conditions O0 The aerial cable should not be bundled with the power cord and the like INSTALL the unit in a room where direct light will not fall upon the screen Total darkness or a reflection on the picture screen may cause eyestrain Soft and indirect lighting is recommended for comfortable viewing Installation Installing batteries Open the battery cover Install two AAA batteries matching the polarities of the battery to the marks Replace the battery cover Q Notes O Do not try to recharge batteries they are not intended to be recharged Use only the size and type of batteries specified Do not mix different types of batteries together or old batteries with fresh ones When the remote control will not be used for a long period of time or when the batteries are worn out remove the batteries Do not throw the batteries into a fire Dispose of used batteries in the specified manner Do not drop dampen or disassemble the remote control Effective range of the Remote O Notes O When there is an obstacle between the TV and the transmitter the transmitter may not operate When direc
23. s Menu 1 When a bilingual program is received DUAL appears CH menu item select e adusi 2 Press SOUND button to select the sound to be heard menu item Adjust Dual and Dual Il appear cyclically on the screen As for NICAM dual program Mono and Dual I and Dual Il appear cyclically on the screen OK exit the menu Notes SOUND As for FM Germany Dual program press SOUND button Monaural the sound mode will switch between Dual and Dual Il Stereo bilingual select To enter into earphone state Press button to enter into earphone state in this state sound is outputted through earphones and speakers sound is muted Press Palsonic the button again to restore O In earphone state the sound menu is shown on the right figure In the menu use CH to select item VOL to adjust the level Or you can directly press VOL button to adjust earphone To exit the menu press OK button volume 20 Timer setting Setting clock 1 Press MENU button repeatedly to display Timer menu 2 Press CH to select Clock 3 Use digit buttons to input the current time for the set If wrong in setting the time press RED button to cancel and input again Digit buttons Notes Before setting the timer please first set the CLOCK item Press the main power switch to turn off the set the clock will be cancelled You need to reset it if you want to use the timer MENU function CH
24. t sunlight and incandescent lamp fluorescent lamp or any other strong light shines on the REMOTE SENSOR of the TV the remote operation may be unstable Using the side AUDIO VIDEO Jacks The optimal use for the side A V jacks are to connect an A V component that is used only occasionally such as a camcorder or video game Connect the Audio Video output jacks of the external unit to the Audio Input jacks and the Video Input jacks External equipment connections The figure below shows how to connect the AV3 input jacks to video equipment z TV SET SIDE S Y Yellow video u White audio L MONO To access the unit connected Red audio R aH to these jacks press 0 AV 2 L7 button until AV3 appears on z A Ne Vid the screen 5 lt a i dale 4 l Oe 2 Signal To video To audio output outputs O nt Q gt O Wo Q a h The figure below shows how to connect the SVHS input to video equipment To access the unit connected to these jacks press 0 AV button until AV3 SVHS appears on the screen White audio L MONO Camcorder etc Q Red audio R L MONO AUDIO R_ _ AV3 SVHS To audio B B To S VIDEO Signal Outputs output Mee S VIDEO VIDEO Note The S VIDEO input terminal has priority over AV3 VIDEO terminal To use equipment connected to AV3 VIDEO terminal disconnect any plug from the
25. tch video program from AV inputs or 21 pin scarts Press 0 AV button repeatedly until you see the appropriate input indicator on the screen B AV2 AV3 E AV button TV VIDEO input select Notes When the signal source input through AV1 AV2 is RGB OK button signal the OSD is AV1 RGB AV2 RGB When AV3 S VIDEO is used the OSD is AV3 S VHS N CH button Switching from AV to TV When the TV set is in AV mode there are three ways for you to switch back to TV mode as follows 1 Press 0 AV button repeatedly until the TV program appears 2 Press the OK button to switch back to TV mode 3 Press CH button to switch back to TV mode Palsonic 11 Automatic Tuning 1 Press MENU repeatedly to display Tuning menu Automatic tuning Manual tuning lt a Automatic tuning 2 Press CH or CH to select Automatic tuning lt 4 MENU CH 3 Press VOL to start automatic Program n item tuning All active channels will man sa be preset and stored into e VOL memory automatically A volume adjust menu item adjust OK exit the menu After automatic tuning the set will return to the first channel program During automatic tuning pressing OK button will stop the process Note Before Automatic tuning we recommend you to set a proper Sound System according to your local area see page 15 Palsonic To exit the menu press OK button 12 Manual tuning lf automatic tuning can
26. ted To exit the menu press OK button 15 Channel delete amp to order the channels To delete an unnecessary channel After presetting the channels you may delete unnecessary channels so that only the channels you want to watch are selected 1 Use digit buttons or channel up down button to select a channel you want to delete for example channel 18 2 Press MENU repeatedly to display Program sort menu wap Fg nit Press CH to select Delete Prg lt JA Press the S M button to confirm Please wait for some time until the Delete Prg menu MENU item does not glitter for the system needs time to delete CH program Sn i Now channel 18 s program is deleted and channel 19 s program move to channel 18 and so on VOL volume adjust menu item adjust OK To order the channels exit the menu S M confirm button You can edit the channel programs in your favourite order S N Cancel the inputting 1 Press MENU repeatedly until Program sort menu appears 2 Press CH to select Swap Prg A use VOL to select a program number or you can directly press digit Swap PrgA 027 buttons to input the number for example 23 3 Press CH to select Swap Prg B use VOL to select a program number or directly press digit buttons to input the number for example 37 If wrong in inputting you Swap Prg B 037 can press RED button to cancel and input again 4 lt 44 Press S M button to
Download Pdf Manuals
Related Search