Packard Bell GN45 User's Manual
Contents
1. Power Button WiFi ECO Card To remove the power button WiFi ECO card first remove the keyboard top cover see Keyboard and then perform the following steps 1 Remove the two screws holding the card 2 Carefully disconnect the flat cable Packard Bell EasyNote GN45 Disassembly Manual rackard vell Fig 27 Removing the power button WiFi ECO card Packard Bell EasyNote GN45 Disassembly Manual 15 rackard vell 16 Notice The information in this guide is subject to change without notice This guide contains information protected by copyright No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent from Packard Bell B V PACKARD BELL B V SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING PERFORMANCE OR USE OF THIS MATERIAL Copyright 2006 Packard Bell B V All rights reserved Packard Bell is a trademark of Packard Bell B V The names of actual companies and products mentioned herein may be trademarks and or registered trademarks of their respective owners The software described in this guide is furnished under a license agreement or nondisclosure agreement The software may be used or copied only in accordance with the terms of the agreement EasyNote GN45 Disassembly Manual Author Olivier Raimbault amp Juan M Calvino First Edition2. To remove the top cover first remove the battery see Battery remove the hard disk drive see Hard Disk Drive remove the optical disk drive see Optical Disk Drive remove the keyboard cover see Keyboard Remove the Express Card if needed and then perform the following steps 1 Turn the notebook upside down and remove all screws securing the bottom cover Packard Bell EasyNote GN45 Disassembly Manual rackard vell 10 INA i Fig 15 Removing the bottom cover screws 2 Remove the four screws securing the top cover to the motherboard Fig 16 Releasing the top cover 3 Separate the top cover from the casing LCD Module To remove the LCD module remove the keyboard top cover see Keyboard and then perform the following steps 1 Remove the four screws holding the LCD module 2 To disconnect the video cable carefully pull the plastic part upward Packard Bell EasyNote GN45 Disassembly Manual rackard vell 11 Fig 17 Removing the LCD module LCD Panel To remove the LCD panel remove the keyboard cover see Keyboard and then perform the following steps 1 Remove the screw securing the LCD cover next to the hinge on each side Fig 18 Removing the LCD cover screws 2 Remove the LCD top cover Fig 19 Removing the LCD cover Packard Bell EasyNote GN45 Disassembly Manual rackard vell 12 3 Disconnect the VGA cable r op Mt Fil ool Fig 20 Disconnecting the
3. July 2006 Version 1 0 Packard Bell B V www packardbell com Packard Bell EasyNote GN45 Disassembly Manual
4. Fig I Removing the battery Hard Disk Drive To remove the hard disk drive first remove the battery see Battery and then perform the following steps 1 Remove the screws on the hard disk drive cover and carefully open it Fig 2 Removing the hard disk drive cover Packard Bell EasyNote GN45 Disassembly Manual rackard vell 2 Pull out the hard disk drive using the plastic tab Fig 3 Removing the hard disk drive 3 Remove the two screws on both sides of the hard disk drive shield va ioe By pi Uy T bees ET DEEE S EI p Fig 4 Unscrewing the hard disk drive shield screws Optical Disk Drive To remove the optical disk drive first remove the battery see Battery and then perform the following steps 1 Release the screw securing the optical disk drive TITT ee TITTET Fig 5 Releasing the optical disk drive Packard Bell EasyNote GN45 Disassembly Manual rackard vell 2 Remove the optical disk drive from the drive bay Fig 6 Removing the optical drive Memory Module To remove the memory module first remove the battery see Battery and then perform the following steps 1 Release the screws retaining the memory module slot cover PE Pe LL 00 00085 Fig 7 Removing the memory slot cover 2 Remove the memory module from the slot and put it aside Packard Bell EasyNote GN45 Disassembly Manual rackard vell ene 0 LEAD FREE PRODUCT CAREFUL HANDLI
5. NG REQUIRED Pre TE ee e n pak ba EHT OG co WF OG OO BG 28 20 ea Laretei eee beste brer rende CEC Fig 8 Removing the memory module WLAN Card To remove the WLAN card first remove the battery See Battery and then perform the following steps 1 Release the screws retaining the memory module slot cover see step 1 in Memory Module 2 Disconnect the wireless antenna cables red circles on Fig 9 ee LEAD FREE PRODUCT i CAREFUL HANDLING REQUIRED aoe ispod nt mn inath ee GHADA CO BT OF OG OG 58 30 a i L a T Fig 9 Removing the WLAN card 3 Remove the two screws securing the WLAN card yellow circles on Fig 9 4 Lift the card from the main board Packard Bell EasyNote GN45 Disassembly Manual rackard vell Keyboard To remove the keyboard first remove the battery see Battery and then perform the following steps 1 Remove the indicated screws on the back of the notebook oe _ a 2 gt me mit x gt a Fig 10 Left keyboard back screw Fig 11 Right keyboard back screw 2 Use a small screwdriver to unlock the keyboard cover on both sides L Fig 12 Releasing the keyboard cover 3 Remove both screws securing the keyboard Packard Bell EasyNote GN45 Disassembly Manual rackard vell Fig 13 Releasing the keyboard 4 Before removing the keyboard disconnect the keyboard flat cable Fig 14 Disconnecting the flat cable Top Cover
6. Packard Bell EasyNote GN45 Disassembly Manual Packard 200 rackard vell 1 Table of Contents OE EEE 2 Technician Notes arrnnrnnnennnnnrnarvnrrvnrnnnnnnnennnnnrnnnenarnnnrnnnennsnnarnnnennnnnarnnnennsnneennnennnnnnennnennnnnsennnennnnnnennsn 2 Disassembly InstructionsS rrrarnnnrnnnevnnnnnrnnrrrannnrnnnennnnnrnnnennnnnrnnnennnnnarnnnennrnnaennnennsnnaennnrneennnnnnennsennsenn 2 Reassembly Instructions rrnrnnnrnnnrnnrrnnrrarrnnrrnnrnnnrnarnnnrnanennrnnnrnanrnarnnrnnnrnnnnneennnennsnnennnennrnnennnennnnnsennne 2 REQUIFED TOOIS cccceccceecceeeeceeece cece eeene eee eee eeeeeeeee ees eesaeeeeeeeee esse eesaeeseeeeeueesaeesaeesaeesaueeseeesaeeseeeseueeneeaes 2 Hazardous Voltage ccc eeccceccceeeceeeeeeeece eee eeeeeeeeeeeeeeeeeeeseeeeeeeseueeseeeseeesaeeseueeseeesaeeseesueesueeseeeseeeseueeaeeenes 3 Avoid Electrostatic DiSCN rge cccccccseccneeceeeseceneeceeeseeeneeeeeeseeseeeeeesaeeseeseuesaeeneeeaueseeeneeeaueteeeneeesueneeenaes 3 Pr UN 3 BU IY EEE EN NN 4 giclee EE GB EEE NE NN NN ENE EE 4 Gje DISK DIVE EE NNN NENNE NNN NE 5 MN NE eaaa se dooscedeehdsandsaedece dese desndaseee cues 6 VAN 7 FT 8 TOD Go EEE EE EE EEE EE 9 0 D 0 EEE EE 10 0 D EEE EEE EEE EE 11 MAN BOT Vunnet tenn sesadnsetedatedududcscunsadudadutndsaeds comers E 12 PU 12 ROST FRE nr 13 NIK 01010 9 0110 eee ee 14 Speaker Assembly rrrannrnnnnrnnnnrrnnrrrnnnnvannrnnnrnnnnsnnnnnnnnnsennnsennasennnsennasennns
7. VGA cable Main Board To remove the main board first remove the top cover see Top Cover and then perform the following steps 1 Remove the four screws securing the main board 18cH2BAKE07 ATLL Fig 21 Removing the main board screws 2 Pull the main board towards the right side and upward to extract it from the casing CPU To remove the CPU first remove the main board see Main Board and then perform the following steps 1 Remove the screws securing the heat sink Packard Bell EasyNote GN45 Disassembly Manual rackard vell Fn en 2 Remove the CPU eawene 2 ee oa eg FO VIHOY OV37 ximhy ET OD UP a 3 a Fig 23 Removing the CPU Express Card Reader To remove the Express Card reader remove the top cover see Top Cover and then do the following 1 Remove the two screws securing the Express Card reader Fig 24 Express card reader slot Packard Bell EasyNote GN45 Disassembly Manual 13 rackard vell 14 Touchpad To remove the touchpad first remove the top cover see Top Cover and then perform the following steps 1 Remove the four screws securing the touchpad to the top cover Fig 25 Removing the touchpad Speaker Assembly To remove the speaker assembly first remove the top cover see Top Cover and then perform the following steps 1 Remove the two screws holding the speaker assembly Fig 26 Removing the speaker assembly
8. ennnsennnsennnsennasennasennnennnsennnsennnee 14 Power Button WiFi ECO Card ornonanenanennnrnnnrnnanenanennnrnnnnnnanennnnnanennnenanennnsnnnnenanenanennnsnnnnenunennnennnsnnnnen 14 NOU nere 16 Packard Bell EasyNote GN45 Disassembly Manual rackard vell 2 Overview This document contains step by step disassembly instructions for the Packard Bell EasyNote GN45 The instructions are illustrated where necessary with images of the part that is being removed or disassembled Packard Bell reserves the right to make changes to the EasyNote GN45 without notice Technician Notes Only technicians authorized by Packard Bell B V should attempt to repair this equipment All troubleshooting and repair procedures are detailed to allow only subassembly module level repair Because of the complexity of the individual boards and subassemblies no one should attempt to make repairs at the component level or to make modifications to any printed wiring board Improper repairs can create a safety hazard Any indication of component replacement or printed wiring board modifications may void any warranty or exchange allowances Disassembly Instructions When disassembling the system unit follow these general rules Turn off the power using the battery switch Disconnect the adapter Remove the SD or MMC card from the device Do not disassemble the system into parts that are smaller than those specified in the instructions Label all removed c
9. onnectors note where the connector goes and in what position it was installed Reassembly Instructions Reassembly is the reverse of the disassembly process Use care to ensure that all cables and screws are returned to their proper positions Check that no tools or any loose parts have been left inside the casing Check that everything is properly installed and tightened Required Tools All disassembly procedures can be performed using the following tools m Small Phillips and flat blade screwdriver Packard Bell EasyNote GN45 Disassembly Manual rackard vell Hazardous Voltage There is hazardous voltage present inside the notebook when it is connected to an AC supply even when the notebook s power switch is off Exposure to hazardous voltage could cause personal injury To avoid risk of injury contact an Authorized Service Provider for proper un installation of optional hardware devices Avoid Electrostatic Discharge Electrostatic electricity can easily damage circuit cards and integrated circuits ICs To reduce risk of damage store them in protective packaging whenever they are not installed in your system Add in cards can be extremely sensitive to ESD and always require careful handling After removing the card from the notebook place the card flat ona grounded static free surface component side up Use a conductive foam pad if available but not the card wrapper Do not slide the card over any surface Befo
10. pas utiliser le systeme quand le capot est enleve WARNUNG Das System darf weder an eine Stromquelle angeschlossen sein noch eine Verbindung mit einer Telekommunikationseinrichtung einem Netzwerk oder einer Modem Leitung haben wenn die Geh useabdeckung entfernt wird Nehmen Sie das System nicht ohne die Abdeckung in Betrieb ADVERTENCIA Aseg rese de que cada vez que se quite la cubierta del port til el sistema haya sido desconectado de la red de alimentaci n y de todos lo enlaces de telecomunicaciones de red y de l neas de m dem No ponga en funcionamiento el sistema mientras la cubierta est quitada WAARSCHUWING Zorg er voor dat alle verbindingen van en naar de notebook stroom modem netwerk etc verbroken worden voordat de behuizing geopend wordt Zet de notebook nooit aan als de behuizing geopend is AVVERTENZA Prima di rimuovere il coperchio del telaio assicurarsi che il sistema sia scollegato dall alimentazione da tutti i collegamenti di comunicazione reti o linee di modem Non avviare il sistema senza aver prima messo a posto il coperchio Packard Bell EasyNote GN45 Disassembly Manual rackard vell Battery Perform the following steps to remove the battery Make sure the power is off Turn the unit upside down Unlock the left battery lock Push battery lock on right outward to the release the battery Slide the battery out of its place in the direction of the arrow me Nr peeee
11. re you install or remove memory modules video memory disk drives circuit cards or other devices protect them from static electricity To do so make sure your notebook s power switch is OFF Then unplug the notebook s AC power cord Before picking up the device you un install you should wear an anti static wrist wrap available at electronic supply stores Be sure to connect the wrist wrap to an unpainted metal portion of the notebook casing As an alternative you can dissipate electrostatic build up by touching an unpainted metal portion of the notebook casing with one hand Then touch the device you are un installing with the other hand and maintain continuous contact with it until it is un installed in the notebook Power Supply Unit Under no circumstances should you attempt to disassemble the power supply The power supply contains no user serviceable parts Inside the power supply are hazardous voltages that can cause serious personal injury Always return a defective power supply to your dealer WARNING Ensure that the notebook is disconnected from its power source and from all telecommunications links networks or modem lines whenever the casing cover is removed Do not operate the notebook with the cover removed AVERTISSEMENT Assurez vous que le syst me est d branch de son alimentation ainsi que de toutes les liaisons de t l communication des r seaux et des lignes de modem avant d enlever le capot Ne
Download Pdf Manuals
Related Search