Oregon EMR201A User's Manual
Contents
1. QUICK START GUIDE OREGON SCIENTIFIC WEATHER COLLECTION SCIENTIFIC B SET UP WIRELESS SENSOR Orecon You will have one of the following Oregon Scientific products EMR201A BAR206A RMR202A BAR208HGA RMR203HGA RAIN AND TEMPERATURE STATION RGR202A o x Assign a channel by sliding selection switch to the appropriate a a S channel 1 2 3 location If installing additional sensors make sure you assign a different channel for each sensor Make sure that you have all of the parts of one of the three QrOoUups of products shown here before the installation of your Slide open battery door Install the battery matching polarity Before placing the sensor outdoors please verify Weather Collection proq uct communication with the main unit by placing the sensor next to the base unit during this setup process Press the reset button WEATHER etre WEATHER Doe M ma Doe M Temperature Temperature Sensor Humidity Sensor Time is synchronized Receiving signal is strong RAIN AND TEMPERATURE STATION Time is not synchronized Receiving signal is weak K LIS Xe wD RS KG NESS ey ss Z i lt A Te Atomic Clock Signal Atomic clock synchronization will automatically occur after installing the batteries Reception takes 2 10 minutes If the signal is weak it can take up to 24 hours to retrieve a valid signal 2 There are two types of signals the main uni2. is during nighttime hours It can take up to 24 hours to receive a signal To complete the installation slide the hood cover on and secure with two base Secure the battery cover with eight screws screws located on the bottom rim of the rain gauge Place the filter in the cup to prevent leaves or other debris from blocking water from entering the cup Contact our Customer Service Department for additional questions website www2 oregonscientific com service phone 800 853 8883 voice address 19861 SW 95th Avenue Tualatin OR 97062
3. opriate icons on main unit display 2 Place the main unit away from other electronic devices that might cause signal interference 3 Decrease the distance between the remote sensor and the main unit Outdoor temperature reading is wrong When does the memory BAR208HGA BAR206A Tilt the tipping funnel on the rain gauge several times and verify a numerical After verifying connection to the base station place the rain gauge outside on O Lies y fying p a RMR203HGA RMR202A reading on the base unit 58 Numerical reading will take approximately a level surface and place a few drops of water on the cross at the base of the 30 45 seconds to transmit to the main unit funnel to check the horizontal level Water will pool to the center of the cross when the rain gauge is level You can adjust the level when securing the rain 7 Press and hold the SINCE button for two seconds The total rainfall and today gauge on the level screws by using the mounting screws rainfall will be reset to zero Weather warning display The Weather Warnings icons will activate when current weather conditions fall under specific temperature is blank barometric or humidity requirements Atomic Clock is not BAR208HGA BAR206A Move the main unit close to a window away from other electronic devices and hit the up button to intitiate syncronizing RMR203HGA RMR202A an atomic clock signal search The best time to achieve successful signal synchronizing
4. t will receive Temperature Signal After installing the batteries the main unit will automatically search for the signal from the wireless sensor Once a temperature reading is displayed on the LCD screen communication is now established Install the required number of batteries in the battery compartment located on the back of each main unit Please monitor atomic clock icon on the bottom part of the LCD display next to the time This icon indicates the status of the clock reception signal sia THN132N 1x Temperature Sensor se 4 Screws Type C 6x OreGcon SCIENTIFIC SET UP RAIN GAUGE FOR THE RAIN AND TEMPERATURE STATION PLACE WIRELESS SENSOR OUTSIDE HH UHH T E Q U E Remove the two base screws located on the bottom rim of the rain gauge Press the RESET button and slide the hood cover off to expose the battery compartment Find a location for the temperature and humidity sensor Press the SEARCH button on the main unit to initiate a wireless sensor search Temperature and thermo humidity sensors should be located in areas Locate the battery compartment and remove the eight screws that secure the protected from the sunlight and rain Mount the sensor under a covered cover Install two AA batteries Before proceeding to install the rain gauge outside please verify location like a roof overhang or under the eaves This will ensure acc
5. urate communication to the main base station temperature and humidity readings Find a location for the wireless rain gauge The wireless rain gauge should be placed on a flat and level surface The location must be away from anything that may block rainfall from entering the rain collector Rain gauge should be elevated off the ground Placing your rain gauge on your outside deck would be an ideal location Remove the packing tape from the tipping funnel The distance between the main unit and remote sensor should not be greater than 100 feet FAQ s Frequently Asked Questions Problem Applicable Models Solutions appears on the All models 1 Check main unit or remote sensor battery levels by viewing the appropriate icons on main unit display temperature display 2 Place the main unit away from other electronic devices that might cause signal interference 3 Decrease the distance between the remote sensor and the main unit Weather forecast icons is The weather forecast feature does not show you current conditions outside rather it will forecast what the displaying the wrong forecast weather will be in the next 12 hours Weather forecast is calculated to be 75 accurate appears on the remote BAR208HGA BAR206A NOTE If you have the RVR203HGA you need to purchase the THGR268 sensor to display outside humidity humidity display RMR203HGA 1 Check main unit or remote sensor battery levels by viewing the appr
Download Pdf Manuals
Related Search