Onkyo HT-S5700 Owner's Manual
Contents
1. beginning Updating the firmware and adjusting the settings will be done automatically but may take some time to complete Please follow the procedures as instructed when you update Note that the update may fail or cause problems for your A V receiver if you do any of the following e Pull out the A V receiver s power cord e Interrupt the power supply to the A V receiver e g if the breaker is tripped or if there is an electrical outage e Insert or remove the LAN cable from a device in your network when updating over a network e Insert or remove a USB memory device from the A V receiver when updating via USB e Operate components connected to the A V receiver via HDMI such as a TV or a recording device If you see No Update on the front panel immediately after you have started the firmware update process you have the latest firmware In this case it is not necessary to do this update Limitation of liability The program and accompanying online documentation are furnished to you for use at your own risk Onkyo will not be liable and you will have no remedy for damages for any claim of any kind whatsoever concerning your use of the program or the accompanying online documentation regardless of legal theory and whether arising in tort or contract In no event will Onkyo be liable to you or any third party for any special indirect incidental or consequential damages of any kind including but not limited to compensation reimb2. ONKYO Firmware Update for the TX NR535 and HT R593 HT S5700 To update the firmware of the AV receiver you can choose from the following two methods update via network or update via USB storage Choose the one that best suits your environment Before proceeding with the update please read the corresponding explanations carefully Update via network You will need a wired Internet connection to update the firmware Update via USB storage Please prepare a USB storage device such as a USB flash memory stick You need at least 32 MB of available space to update the firmware Precautions for your Firmware Update Please enter NET mode before starting the update The firmware update may fail if an external HDMI control signal is input during the update procedure Please be sure to turn off the HDMI control function RIHD on your A V receiver before starting the update How to turn off RIHD In the Main menu select Hardware Setup then HDMI Set HDMI Control to OFF The firmware update should take 15 to 40 minutes depending on receiver model Once the update begins don t turn off the power supply to the A V receiver until it is time to restart it Depending on the conditions of the network a firmware update via a network may take more than one hour or even fail to finish If the update is not completed within two hours turn off the power supply by pushing the ON STANDBY button and then try updating again from the
3. files when complete ere ae amp Local Disk C J 4 items Cancel 4 items 3 Connect the USB Memory Device to the USB port of your computer and copy the contents of the unzipped extracted folder onto your USB Memory Device 4 Safely eject the USB Memory Device from your computer The product that you are using may have unexpected issue which will be addressed by this F W update Please check your FW version below and proceed for the FW update ONKYO Firmware Update for the TX NR535 and HT R593 HT S5700 How to upgrade the firmware via the USB 1 Turn on the receiver and select the USB input and wait for the Now Initializing process to complete 35 45 seconds 2 Insert the USB Memory Device containing the software into the front panel USB port of the receiver 3 From the front panel press and hold the USB input button followed by the On Standby button Unit will display Update lt Enter gt Press Enter 4 Press the Enter button on the front panel to begin the update 5 Do not shut the unit off until Complete is shown on the front display 6 Once the update has completed check the firmware version to confirm that the unit is fully up to date If it is not run the update again To check the firmware version press the Home button on the front panel or remote control Highlight Hardware Setup and press enter Highlight Firmware Update and press enter The c
4. tup and press Enter 3 Select 7 Hardware Setup and press Enter 4 Select Firmware Update and press Enter 5 Select Update via Net and press Enter 6 Do not shut the unit off until Complete is shown on the front display 7 Once the update has completed check the firmware version to confirm that the unit is fully up to date If it is not run the update again 8 Tocheck the firmware version follow steps 1 4 The current firmware version will be displayed TV screen once Firmware Update is selected Current firmware version 1080 9110 0000 ONKYO Firmware Update for the TX NR535 and HT R593 HT S5700 How to prepare the USB Memory Device 1 Download the zipped firmware update file and save to the Desktop of your computer http download onkyo com AVR0017 ONKAVR0017_ 0000000000NALANA_108 zip File name ONKAVR0017_0000000000NALANA_108 2 Right click on the file and select Extract All and place the extracted folder on the Desktop of your computer Open Extract All Scan with Microsoft Security Essentials Open with b Restore previous versions Send to gt Cut Copy Create shortcut Delete Rename Properties Select a Destination and Extract Files a Name r nize v Files will be extracted to this folder m p AVROOOD Release KAVROOOD_OOEAEAOOEAEAEA 120 gp Downloads __ ONKAVROOOD_OOEAEAQOEAEAEA of1 Recent Plac __ ONKAVROOOD_OOEAEAOOEAEAEA of2 Show extracted
5. urrent firmware version will be displayed on the Firmware Update page Current firmware version 1080 9110 0000
6. ursement or damages on account of the loss of present or prospective profits loss of data or for any a E A E E E E N E EAT ONKYO Firmware Update for the TX NR535 and HT R593 HT S5700 We are pleased to offer this firmware update for the best possible performance of your AV Receiver To check the firmware version press the Home button on the front panel or remote control Highlight Hardware Setup and press enter Highlight Firmware Update and press enter The current firmware version will be displayed on the Firmware Update page A firmware update is now available through the Network or USB connections Latest Firmware Version 1080 9110 0000 The 1 29 2015 update will address the following 1 Improves operation of Spotify Connect The 11 04 2014 update will address the following 2 Adds support of Spotify Connect Please note below e Please download the Spotify Music app from the iTunes or Google Play store prior to installing this update e After installing this update Spotify will no longer be able to be controlled through the receivers OSD menu e All control of the Spotify service will be done through the Spotify Music app We hope you enjoy the improved functionality this update provides to your AV Receiver ONKYO Firmware Update for the TX NR535 and HT R593 HT S5700 How to upgrade the firmware via the Network 1 From the front panel or remote press the Home button 2 Select Se
Download Pdf Manuals
Related Search