O'Neil MICROFLASH 2TE User's Manual
Contents
1. RF Power ON OFF LED Status LED Charge LED Figure 2 Latch Power Port NOTE When the cable plug is inserted into the Power Port the cable plug must lay horizontally to the bottom of the surface of the case MICROFLASH 2 PRINTER USER S GUIDE Using the Battery General Guidelines If the printer has not been used for a long period of time it may be necessary to recharge the battery For more information see Charging the Battery on page 2 Charging the Battery If the battery is low when the printer wakes up the printer sounds three short beeps Plug the AC Adapter into an appropriate power source and into the Power Port on the printer The Charge LED will flash and progress from red when the battery is very low in power to orange and then to a solid green when the battery is fully charged A complete charge takes approximately 2 5 to 3 5 hours Note To obtain full battery capacity a new battery must cycle through two to three complete depletions and recharges Note To restart a charge unplug the power cord Wait 30 seconds then replug the power cord Determining Battery Condition To determine the battery s condition print a self test For more information see Printing a Self Test on page 4 The battery voltage varies between 5 8 and 8 0 volts Caution There is a risk of explosion if the battery is replaced by an incorrect type Dispose of used batteries a2. ASH 6 2 PRINTER USER S GUIDE Using Buttons LEDs and Audio Indicators Button Functions Green Self Test Button Short press If printer is asleep printer wakes up If printer is awake paper feeds Long press Prints a self test press and hold for five seconds Bluetooth Power Button Short press If printer is asleep and RF power is off printer wakes up and RF power is turned on If printer is asleep and RF power is on printer wakes up and RF power is turned off If printer is awake and RF power is off RF power is turned on If printer is awake and RF power is on RF power is turned off LED Indicators Bluetooth LED Indicators LED Description Blue flash power is on and printer is awake fast Blue flash RF power is on and printer is asleep slow Off RF power is off 10 MI CROFLASH 2Te PRINTER USER S GUIDE Charge LED Indicators LED State of Charge Action Flashing Charge in progress Wait for the charge Orange LED to turn green Flashing Red Green Charge complete None Red flash Battery is too cold Change environment slow Red flash High temperature Change environment fast Red to Battery voltage is very Wait for solid red orange solid low Restart charge Red to Battery voltage is too Replace battery orange flash fast high Orange flash Charge timeout Restart battery slow charge Orange flash In
3. CABIL ost Reliable Portable Printer MICROFLASH 2 User s Guide TABLE OF CONTENTS microFlash 2te Printer Top View 1 Using the Battery General Guidelines 2 Charging the Battery 2 Determining Battery Condition 2 Installing Paper 3 Printing a Self Test 4 Clearing Linerless Paper Jams 5 Removing a Paper Jam 5 Avoiding Paper 5 Configuring the Printer 6 Using Printer Data Cables 7 Using Bluetooth 9 Bluetooth Parameters 9 Using Buttons LEDs and Audio Indicators 10 Button FUNCIONS 10 LED Indicators 10 Audio Indicators 12 CardReader Audio Indicators 12 Using a CardReader 13 General Guidelines 13 Media Supplies 18 MI CROFLASH 2Te PRINTER USER S GUIDE microFlash 2te Printer Top View Bluetooth Button LEDs Self Test Button Print Head Roller Release Lever Data Port Paper Paper Cavity Figure 1
4. MI CROFLASH 2Te PRINTER USER S GUIDE Copyright This manual and any examples contained herein are provided as is and are subject to change without notice O Neil Product Development Inc makes no warranty of any kind with regard to this manual including but not limited to the implied warranties of merchantability and fitness for a particular purpose O Neil Product Development Inc shall not be liable for any errors or for incidental or consequential damages in connection with the furnishing performance or use of this manual or the examples herein This guide is copyrighted All rights are reserved This guide may not in whole or in part be reproduced translated stored in a retrieval system or transmitted in any form or by any means electronic mechanical photographic or otherwise without the prior written consent of O Neil Product Development Inc 17 MICROFLASH 6 2 PRINTER USER S GUIDE Media Supplies O Neil Product Development Inc offers seven certified grades of paper for use in the printers Our certified supplies are guaranteed compatible this important qualification means that rigorous performance and image life testing have been performed Quality supplies are key to obtaining optimal image quality and print performance Quality supplies are also the key to extending the life of the printer O Neil Product Development strongly recommends using O Neil Certified Supplies only For more information c
5. SI EN 390 328 VL amp 1 2904 11 ETSI EN 303 439 1 V LAT 2006 08 ERM EN 40 17 VL2 1 200 0 EN 55621 199 CISPR Publication 22 1997 Chun Lindis and Methods EN 55624 1999 1 0 2 20800 CISPR 24 ITE Insanity Chrscteristkcs Limits and Methods of Mss EN 406 4 1 EPPS A 1 1598 Discborge VN 6996 4 5 AT 1998 RF Oe Blectrical Pact Tracker 5 1995 Vols Surge TP 21993 Magnetic EN 61906411 1994 Dips Sheri 00 And Variations 2000 Harmenkc Current mdriens ENEIDI 1 95 1 Voltage 397931098 amd Hicker 180 Industry Comets THD CEO Th s Device a RF device intended for office and hame uw In all FU and EFTA monder states Belgtam Denmark France Groves Inetond Haly Lexembserg The Nethertamds Portugal Spain Sweden Untied wis EFTA Lischtenziin Norwory amd Swttoertued L the undersigned hereby declare that the equipment specified above conforms to the above Direceives s and Seandard Company Official Ken Carbon Director of Electrical Engineering Date 4112008 Contact O Neil Product Development Ind amp Court Crowahill Keynes UK MKS OJP Phone INT 44 1905 393300 Fax INT 44 1908 393400 www oueilprinter com 16
6. ccording to the instructions MI CROFLASH 2 PRINTER USER S GUIDE Caution The operating temperature of this portable printer is 50 C However the operating temperature when used with O Neil power supply for charging the portable printer is limited to 40 C Please charge the printer in a suitable location that meets this temperature requirement Caution For US Canada Please only use the O Neil part number 220240 100 power supply with this product Installing Paper l Insert a roll of paper with the end of the roll exiting from the bottom of the paper cavity Figure 3 2 Open the print head by raising the green print head release lever until it stops Figure 4 Figure 3 Figure 4 3 Wake up the printer by briefly pressing the green self test button Figure 5 7 8 MICROFLASH 2 PRINTER USER S GUIDE Feed the end of the paper under the roller The paper automatically feeds under the roller and exits from the top of the print head Verify the paper exits straight Figure 5 Lower the green print head release lever Figure 6 Feed the paper through the printer s cover Figure 7 Figure 6 Figure 7 Close and latch the printer s cover Tear off any excess media Printing a Self Test 1 2 3 After installing the paper open the printer s cover Press and hold the green self test button for approximately five seconds until printing begin
7. lprinters com MI CROFLASH 2Te PRINTER USER S GUIDE Using Printer Data Cables l Select the appropriate cable for use with the host device you are using 2 Insertthe plug into the printer data port Figure 12 Figure 12 3 Lead the cable through the notch on the outside of the printer cover 4 With the cable exiting the front of the printer close and latch the printer cover MICROFLASH 6 2 PRINTER USER S GUIDE Note When closing the printer be cautious of the cable that is exiting to prevent pinching of the cable Remove the cable when the printer is not in use Figure 13 MI CROFLASH 2Te PRINTER USER S GUIDE Using Bluetooth Note The following information applies to printers with Bluetooth capabilities Radio printers are configured with default factory settings To determine your printer s radio configuration print a self test For more information see Printing a Self Test on page 4 If you have multiple printers configure them specifically for use in your environment For proper system operation set the following parameters on your printer and host computer Bluetooth Parameters Device Name Authentication Bondable Discoverable Connectable w Encryption For information on setting parameters see Configuring the Printer on page 6 Contact your network administrator to verify the proper radio settings for your environment MICROFL
8. ontact O Neil Printer Supplies Group at 949 458 6400 Maintenance Supplies We recommend that you follow a regular maintenance schedule using our cleaning card or cleaning kit when using linerless labels O Neil s cleaning cards are designed to effectively remove dirt and other contaminants from the thermal printhead rollers and paper path resulting in a clean crisp image output every time Our cleaning kits remove any adhesive residue when using linerless labels in addition to dirt and other contaminants For more information contact O Neil Printer Supplies Group at 949 458 6400 For more information For information about using the printer contact O Neil at 949 458 0500 or visit www oneilprinters com 18 CABIL The Most Reliable Portable Printers World Headquarters O Neil Product Development 8 Mason Irvine CA 92618 2705 Ph 949 458 0500 Fx 949 458 0708 Europe 6 Joplin Court Crownhill Milton Keynes MK8 0JP United Kingdom Ph 44 0 1908 635360 Fx 44 0 1908 635361 WWW ONEILPRINTERS COM COPYRIGHT 2008 O NEIL PRODUCT DEVELOPMENT INC Part Number 110228 001 April 2008 Made in USA
9. roval of manufacturer could void the user s authority to operate this equipment This device and its antenna s must not be co located or operated in conjunction with any other antenna or transmitter within 20 centimeters INDUSTRY CANADA STATEMENT Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation 14 MI CROFLASH 2Te PRINTER USER S GUIDE Applicable Directive 89 336 EEC 73 23 EEC Applicable Standards EN55022 1998 EN55024 1998 EN60950 1992 5 Dx 15 MI CROFLASH 6 2 PRINTER USER S GUIDE DECLARATION OF CONFORMITY According to ISO TEC Guide 22 aud EN 45014 THE PRODUCT HEREWITH COMPLIES WITH THE REQUIREMENTS OF THE LOW VOLTAGE DIRECTIVE 73 23 THE EMC DIRECTIVE 89 336EEC Mauufacrarer s Name European Representaave O Neil Product Development Inc O Ned Product Development ltd 8 Mazon Irvine 92618 USA 6 Joplin Court Crownhill Keynes UK MKS OJP Declares that the product listed below Product Type ITE Residential Commercial and Light Industrial Product Name MFlte Model Number MF te Options 31067004 Radio Date Issued 411 2008 Conforms to the following product peci amp canon Safety EN 0950 1 2001 60950 1 2001 and EMC requirements Verepesa Startar r ET
10. s After printing begins release the green self test button MI CROFLASH 2Te PRINTER USER S GUIDE Clearing Linerless Paper J ams Note The following applies to printers that are designed for linerless paper A paper jam may occur if an O Neil printer with linerless paper installed is left in a cold environment without being used for an extended period of time such as overnight Removing a Paper Jam Note Do not use a knife to fix the paper jam This may cause damage to the printer roller underneath the paper l Open the print head by raising the print head release lever until it is fully open Do not stop at the partial open position 2 Roll the media tightly onto the spool Figure 8 Avoiding a Paper Jam There are two options to help avoid paper jams with linerless paper MICROFLASH 2Te PRINTER USER S GUIDE Remove the Linerless Paper from the Print Head If the printer is going to be in a cold environment for a long period of time remove the linerless paper from the print head The paper can remain in the printer Figure 9 Advance the Paper When the printer is turned on hold the paper and then advance the paper Verify the paper exits the print head straight Figure 10 Figure 11 Configuring the Printer The printer has many configurable settings To configure or upgrade firmware download the latest Windows configuration program at www onei
11. s on page 10 13 MICROFLASH 2 PRINTER USER S GUIDE Agency Approvals FE FCC Notice This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This equipment has been verified to comply with the limits for a class B computing device pursuant to FCC Rules Operation with non approved equipment is likely to result in interference to radio and TV reception The user is cautioned that changes and modifications made to the equipment without the app
12. ternal error Reset printer fast Power LED Indicators LED State of Charge Action Solid green Printer is on None Black Printer is off Printer needs to be turned on using the Green self test button Printer needs to be recharged 11 MICROFLASH 2 PRINTER USER S GUIDE Audio I ndicators Beep s Description Action 1 Printer wakes up None 2 Out of paper Install paper 3 Low battery Charge battery 1 short RF power is on when None blue RF power button is pressed and power was turned off 2 short RF power is off when None blue RF power button is pressed and power was turned on 1 long Boot code is starting or Redownload restarting when firmware downloading new firmware 8 short CRC error in firmware Redownload firmware CardReader Audio I ndicators Beep s Description Action 1 long Bad read Reswipe card 2 short Good read None 12 MI CROFLASH 2 PRINTER USER S GUIDE Using a CardReader Note The following information applies to printers installed with the CardReader option CardReader Slot Figure 14 General Guidelines To use the CardReader swipe a card with the stripe facing toward the printer then slowly move the card left or right in the CardReader slot For information on CardReader LED indicators and audio indicators see Using Buttons LEDs and Audio Indicator
Download Pdf Manuals
Related Search