Omron INTELLI 637IT User's Manual
Contents
1. Or the blood pressure val ues are displayed abnormal ly high low Blood pressure value tends to fluctuate depending on the mental state during measurement or the measuring time Breathe deeply to relax yourself and make measurement again Refer to Page 22 If you cannot resolve the problem even after taking the above mentioned measures please contact the nearest OMRON dealer or distributor 24 Spare parts and accessories OMRON considers due to the used high company and quality standards the main unit as a non serviceable part because of the necessity of proper calibration after replacement of high tech components The cuff can be replaced by an authorised expert Specifications Name OMRON Fully Automatic Blood Pressure Monitor for measurement on the wrist Model 637IT Display Dot matrix LCD display Measurement Oscillometric method Measurement Range Pressure 0 to 299 mmHg Pulse rate 40 to 180 min Accuracy Pressure within 3 mmHg Pulse rate within 5 of reading Inflation Automatic inflation with pump Deflation Automatic rapid deflation Pressure Detection Electrostatic capacity semi conductor pressure sensor Power supply Two LRO3 batteries AAA Battery Life Approximately 300 times of measurement when using alkaline batteries In case of the monitor is used three times a day inflat ing to 170 mmHg at the room tem2. bring you back the graph display You can use 3r 1 ors 4 F the arrows in the graph and memory dis E 40 play to leaf through the measurements mmHg DIA BPH mmHg Detail Screen of Data in Flashing Display The systolic blood pressure is higher than 170mmHg When a systolic blood pressure above 170 mmHg is measured twice the ai symbol is displayed in the graph When a systolic blood pressure above 170 mmHg is measured three times the aia sym bol disappears and the screen automatically changes to the hypertension display The Display screen where the Graph Display Screen of maximum displayed blood pressure value Systolic blood pressure Hypertension Type y axis will change from 170 mmHg to 210 values higher than 170 mmHg mmHg are measured twice How to change the settings The settings of your OMRON 637IT blood pressure monitor can be changed according to your own preferences and comfort To enter the setting menu please press the SET button when your blood pressure monitor is switched off By using 4 you can select your preference By pressing the SET button again you lock your preference and proceed to the next item as shown in the figure The on off button O I can be used to Switch the monitor off again 15 If you push the SETTING button while the power is turned off the Setting Screen is displayed in the order shown in the picture You can select the setting or set the
3. button Point the mouse pointer to Settings on the menu Click Control Panel 4 Open the Add Remove Programs by double clicking the icon 5 Execute the installation Click the install button Follow the instructions The software is installed on your personal computer How to uninstall the software 1 Open the control panel Click the Start button Choose Settings Click Control Panel 2 Open the Add Remove Prograns icon by double clicking 3 Delete the application Click BPFile from the list Click the Add Remove button The confirmation screen is displayed Click Yes Click OK 17 How to connect your 637IT blood pressure monitor to your PC Connect your 637IT blood pressure monitor with your PC using the included USB cable The mini USB connector small connector should be connected to your 637IT blood pressure monitor and the normal USB connector large connector should be plugged into your personal computer How to use the software Open the BPFile application from the program list or your desktop and the following screen is shown on the screen Counter tmn Tin ern BP chat m a OU a Fani uri Tira ar Ter cabo acad Serm MP MOT PER P Td BAYT dil mami Shere gratae C m cue EP ees PT cim Omron imd By pressing the DATA button your are able to transfer the memory of your 637IT blood pressure monitor to your personal computer By pressing t
4. may arise as a ZA Caution How to Use the Memory Function 11 result of incorrect handling How to Use the Graph Function 12 Material damage refers to a wide range of damage involving your house How to change the settings 13 household goods domestic animals and pets Auto Memory oue ca ee e ern Rn doen VQ 14 Examples of signs Position Sensor xv ono eS ee E 15 The icon indicates prohibitions what you cannot do Matters involving actual pro Left or right wrist measurement 15 AM p i hibitions are indicated by text or pictures in or near Alarm soe nee 15 The left icon refers to prohibition to disassemble TUG Ec 16 Delete data ee 16 The icon indicates something compulsory always follow Matters involving actual Reset settings ii 16 Q compulsory actions are indicated by oy or pictures in or near s The left icon refers to general compulsion How to use the computer interface 17 What Is Blood Pressure 5 20 A Caution Blood pressure at the upper arm and wrist 21 Self diagnosis of measured results and treatment are dangerous Please follow the Maintenance and storage issues 22 instructions of your doctor Error indication 2h pp ee age dee arp 23 Self diagnosis may worsen the disease When the arterial sclerosis proceeds due to diabetics hyperlipemia or hype
5. day only the third reading will be displayed On the other hand all read ings will be stored in the memory See also page 11 There are three different graphs available All data graph displays all measurements per week Morning data graph displays all morning measurements per week Evening data graph displays all evening measurements per week No graph display is provided for daytime data only To display the graph push the GRAPH CALL button All Data Graph is displayed Push the GRAPH CALL button again to display the vin Ly Ud Morning Data Graph a l Qa Morning Data Graph Push the GRAPH CALL button again to display the Evening Data Graph Each time you push the GRAPH CALL button All Morning and Evening data are displayed in that order repeatedly Night Data Graph 12 Explanation of the graph display Blood Pressure Values sys Date of tolic diastolic mmHg When the GRAPH button is pushed the latest Measurement measurement will appear in a flashing display In the example the measurement is made on January 31 at 22 40 The graph shows 140 at 1 mmHg for systolic and 95 mmHg for diastolic e all ll I il top and bottom of vertical bar and a pulse rate J n Jl of 90 beats a minute Pulse Month Days of a Week Rate When you push the memory button in the graph display the details of the measurement will appear Pushing the graph button again will
6. your display By pushing the 4l buttons you can enlarge the readings PULSE DI SYS pss 1 1 8 70 gt 118 48 How to Use the Memory Function Your OMRON 637IT blood pressure monitor is able to store maxi mum 90 measurements including date and time When your blood pressure monitor is holding 90 measurements the oldest will be deleted to store a new measurement Y OMRON deu 1 99 Press the M memory button when your blood pressure monitor is Switched off The latest measurement will be displayed Each time you push 4 2 button an earlier measurement will be displayed By pushing the b I button a later reading is displayed By pushing the GRAPH button the selected measurement is dis played in a weekly graph see also How to use the graph function Push the memory button to return to the memory display again Date and Time of Measurement 11 How to use the graph function This monitor has the possibility to display the stored measurements as a graph In order to get a clear history of your blood pressure the measurements are put in time zones Morning Measurements made between 0 00 and 9 59 Daytime Measurements made between 10 00 and 17 59 Evening Measurements made between 18 00 and 23 59 The last measurement in each time zone will be displayed For example if you measure 3 times in the same time zone on the same
7. Data Deleted Blank Reset settings Screen In this menu you can choose to reset all the settings to the factory pre RESET SETTINGS I set settings The factory preset for this menu is NO If you choose YES KS HO by using the 4 button the monitor will ask you for a confirmation ARE YOU SURE After confirmation by selecting YES all the settings will be changed to the factory mode Reset Settings YES The monitor will return to the AUTO MEMORY SCREEN You can turn off Screen your monitor by pushing the O I button ARE YOU SURE D gt YES NO Are You Sure YES Screen 16 How to use the computer interface This blood pressure monitor has a computer interface and is supplied with software to transfer the memory of the blood pressure monitor to your personal computer Required operating environment The following operating environment is required to operate the communication software as supplied on the CD ROM Personal computer PC AT compatible with CPU of 80486 or above or with any Pentium processor OS Windows 98SE ME XP 2000 Memory RAM 16 MB or more Hard disk Free area of 10 MB or more is necessary Display 640 x 480 pixels or more Disk drive CD ROM drive Connection port Free USB connection port How to install the software 1 Turn on your personal computer P Your windows desktop is displayed 2 Insert the CD ROM in the disk drive 3 Open the control panel Click the Start
8. OMRON Instruction Manual 637IT Fully automatic blood pressure monitor for measurement at the wrist Gebrauchsanweisung 637IT Vollautomatisches BlutdruckmeBgerat zur Messung am Handgelenk Gebruiksaanwijzing 637IT Volledig automatische bloeddrukmeter voor de pols Manuel d instructions 637IT Tensiom tre enti rement automatique pour prise de mesure au poignet Manual de instrucciones 637IT Aparato completamente autom tico para medir la presi n arterial en la mu eca Manuale di instruzioni 637IT Misuratore della pressione per il polso completamente automatico English e Deutsch Nederlands Francais Italiano Espa ol A e 637IT Vers 01 07 02 1 Table of Contents Before Measuring Your Blood Pressure Se Measuring Your Bood POSSUO UTOR 3 Notes on Safety Please read thoroughly before using this monitor Notes on Safety seins coe uten ehe Enti m de 4 Names and Functions of the Parts 5 The warning signs and the sample icons shown here are listed for you to use the product safely How to Insert the Batteries 6 and correctly as well as to prevent the risk of damage to you and others How to Set the Date and Time 7 The icons and meanings are shown as follows How to Measure Blood Pressure Correctly 7 Corect POStuIe vc se rid mre X Fee oaks EX 9 Warning sign Contents How to Measure Blood Pressure 10 C Indicates matters in which bodily harm or material damage
9. batteries out of the monitor if you intend not to use the monitor for a long period app 2 months How to Set the Date and Time Before using your OMRON 637IT for the first time you have to set the date and time After turning the monitor on by pushing the i O I button the initial screen see picture will be available for a 0 00 few seconds After the initial screen you will proceed automatical ly to the TIME SET screen For instruction how to set the date and time refer also to page 16 in Chapter How to change the set tings Initial Screen After reaching the time screen you will see the Gregorian calen b d dar year day month The year will be flashing TIME SET 1 By using the 4 amp buttons you can set the current year 17 2 By pushing the SET button you will lock the year and proceed 7 2002 7 1 1 0 00 to the next item Time Screen vl For setting the month date and time repeat step 1 and 2 After setting the minutes you will proceed to the DELETE DATA screen Please turn off your monitor by pushing the O I button Your OMRON 637IT is ready for use now How to Measure Blood Pressure Correctly How to wrap the cuff In order to measure your blood pressure correctly it is needed to wrap the cuff around your wrist in a correct way If not correct measurements are not possible Please follow the coming instructions left wrist 1 Make sure that your wrist is bare and will be wrappe
10. d over your skin 2 Make sure that you clothing is not constraining the flow of your blood 3 Make sure that the wrist left or right to measure is selected from the settings menu see also page 15 The left wrist is preset 4 Place the cuff over your left wrist with your thumb facing upwards Leave app 10 15 mm between the cuff and the bottom of the palm of your hand as shown in the figures 4 Pull the wrist cuff upward and close the cuff firmly with the Velcro tape as shown You can use your 637IT also on your right hand after selecting right wrist measurement in the SETTING MODE People with a slender wrist wrist circumference of less than 145mm may feel loose because the cuff may not be wrapped firmly Please do not force the cuff it will not affect the measurement How to obtain a correct posture Achieving a correct posture before measuring your blood pressure is important since an incorrect posture might give you incorrect readings To achieve a correct posture please follow the instructions see pictures 1 Sit down and stretch your back 2 Relax yourself by relieving the stress from your shoulders and arms 3 Breath several times deeply and return to natural respiration 4 Do not sustain your wrist with your other hand and avoid stress in your hand by making firm grips or large extensions Correct Posture Measuring your blood pressure and pulse If yo
11. date and time with the buttons To finish the setting push the ON OFF button Automatic Memory Setting Refer to Page 14 AUTO HEHORY ON OFF Reset Settings Refer to Page 16 RESET SETTINGS YES O Auto memory gt gt on OFF lt YES HO Position Sensor Setting Refer to Page 15 POSITION SENSOR SIGHAL k OH OFF Measuring Wrist Setting Refer to Page 15 WRIST LEFT RIGHT All Memory Erasure Time Setting Refer to Page 16 Refer to Page 16 DELETE DATA TIME SET lt lt 2002 1 1 0 00 Alarm Setting Refer to Page 15 ALARM SET 8 00 20 00 amp J You can either enable ON or disable OFF the memory function of your blood pressure When the auto memory function is switched off the measure ment will not be stored When using your OMRON 637IT monitor with more than one person it is recommended to disable the auto memory function The auto memory function mode is ON when you purchased your OMRON 637IT factory preset 14 Automatic Memory Screen AUTO HEHURY ON SFF 4 r N Automatic Memory OFF Screen Position sensor The position sensor of your OMRON 637IT can be switched ON or OFF In the factory preset the position sensor is enabled If the position sensor is switched ON you can choose to have the optimal w
12. eaningful readings Avoid eating and drinking alcohol smoking sport and taking medicines before measuring your blood pressure as this could affect your blood pressure level Before you start sit comfortably on a chair and relax It is recommended to check your blood pressure at least twice a day in the morning after getting up and in the evening after work or as advised by your doctor Do not move and do not speak while the measurement is being taken Avoid measuring your blood pressure while you are in a moving vehicle Allow an interval of at least three minutes between readings Otherwise congestion of blood might occur and distort the readings Always remove the cuff between readings Bare your wrist and take of your watch and jewellery before applying the cuff Do not constrict the flow of your blood if you push up your sleeve Cautions Blood pressure measurement is not suitable in case of serious arteriosclerosis hardening of the arteries The pulse rate indicator is not suitable for monitoring the frequency of cardiac pacemakers If you suffer from disorders of heart rhythm known as arrythmia you should only use this blood pres sure monitor in consultation with your doctor In certain cases oscillometric measurement methods can produce incorrect readings Pregnant women should only measure their own blood pressure in consultation with their doctor since the readings may be changed by the pregnancy Please remember Sel
13. earest OMRON dealer If you cannot resolve the problem even after taking the above mentioned measures please con tact the nearest OMRON dealer 25 Troubleshooting Trouble Possible cause How to correct Nothing is displayed when you push the ON OFF button Measurement cannot be made Or the blood pressure values are displayed abnor mally high low Replace the batteries with new ones See to Page 6 Batteries are worn out The directions of polarities of inserted batteries and are wrong Insert the batteries correctly Refer to Page 6 Measure your blood pressure again in correct posture Refer to Page 9 The wrist cuff is not held at the level of the heart The wrist cuff is not Wrap the wrist cuff correctly Refer to wrapped firmly Page 7 Too much stress is applied Relax yourself and make measure on your shoulder or arm ment You are talking or moving your hands during meas urement Be still and make measurement The blood pressure values differ from the values meas ured at brachial Refer to the section on Wrist Blood Pressure Monitor Refer to Page 21 Blood pressure values are displayed before the monitor inflates to the required value Contact the store where the unit was sold or the nearest OMRON distributor Air is leaking from the wrist cuff Blood pressure value fluc tuates each time of mea surement
14. ety of Hypertension This classification is made based on the blood pressure values measured at upper arm by sitting on the chair in the hospital regardless of the age Blood pressure at the upper arm and wrist Wrist Blood Pressure Monitor Blood pressure is usually measured at brachial artery As the wrist arterial vessel is connected to the brachial ves sel wrist blood pressure values are close to brachial ones Brachial artery Wrist artery Radial artery Heart Ulnar artery and reflect the change of brachial blood pressures However in case there is a circulatory disorder such as arterial infarction fairly large difference is observed between the brachial and the wrist blood pressure values After consulting with your doctor use the wrist blood pres sure together with the brachial pressure for your health management 21 Diseases influencing blood pressure values Diabetes hyperlipemia or hypertension accelerates arterial sclerosis which causes dangerous disease such as cerebral apoplexy or myocardial infarction or induces arterial stenosis or peripheral circulatory disorder In these cases the wrist and brachial blood pressure values may differ greatly Even in healthy people a difference of 20 mmHg may occur if the measuring conditions are not proper Therefore do not try to diagnose the measurement values by yourself but be sure to follow the instructions of your doctor In addition difference of wri
15. f measurement is not the same as medical treatment You should never change the dose of medicines as prescribed by your doctor Before using your OMRON 637IT for the first time Your blood pressure monitor the benefits The OMRON 637IT is a compact fully automatic wrist blood pressure monitor Operating on the oscil lometric principle it measures your blood pressure and pulse rate comfortable and quickly from the wrist It contains an intelligent system for fuzzy controlled inflation known as Intellisense This is an advanced method of oscillometric measurement No pre setting of re inflation is necessary The OMRON 637IT has a Position Sensor The Position Sensor is able to determine the optimal height of your wrist heart level for the blood pressure measurement Measuring at the heart level is extremely important since measuring at a higher or lower position will give wrong results The OMRON 637IT has a large DOT matrix display enabling you to enlarge the digits and showing you graphs Together with the USB computer interface and the built in alarm function for same time measurements or pill intake your OMRON 637IT is the optimal device to manage your blood pres sure Main unit Batteries for monitoring Two LRO3 alkaline batteries SR Y Instruction Manual amp J Ke CD ROM Names and Functions of the Parts Data Transfer Port Connects your 637IT with y
16. he TIME button you are able to set the date and time in your 637IT blood pressure monitor By pressing the ID button you are able to set your personal name in your 637IT blood pressure monitor By pressing the CLOSE button you are closing the program 18 How to create a data file Brin marron Press the DATA button on your screen Fear ili m di iue Press the Dir button on your screen and CAN iii name the file Press OK The file can be opened in most windows programs like Excel Word How to set the time Press the TIME button on your screen The time and date are read from your 637IT blood pressure monitor Change the time and date if applicable in the white field ni 2 riw maim Trma EENE EH 2H Teas paa CUITE iaj rna n Ww EF Tin Cty amd bp raa n rl 0D a a dD EE T 19 What is blood pressure Blood is pumped to artery by the beat con traction and expansion of a pump called the heart The pressure to pump out blood to artery is called the systolic blood pressure The pressure when the heart expands as the blood having circulated the whole body returns is called the diastolic blood pres sure Health and blood pressure Blood pressure fluctuates being affected by everyday life and age Hypertension is a sign that can cause dangerous diseases such as cerebral apoplexy or myocardial infarction to occur easily By understanding the state of you
17. ies out if the monitor is not used for a long period app 2 months or more Electro Magnetic fields can influence the measurement Do not use a protable phone near the unit Disposal of this product and used batteries should be carried out in accordance with the national regulations for the disposal of electronic products 22 Error indication If the measurement is not made correctly the following error can be displayed After severa seconds Error Cause How to correct 28 1 2561 Measure your blood pres Bele 1 Bus i sure again without moving HEIGHT You moved your wrist i your wrist until the meas mmHg mmis during measurement urement is completed Refer to Page 10 E wn OB 25 1 8 15 mmHg After several seconds You moved your arm or body or talked during measurement Measure your blood pres sure again without moving your arm or body Refer to Page 10 E E After several 25 8 15 seconds mmHg You moved your arm or body extensively during measurement Measure your blood pres sure again without moving your arm or body Refer to Page 10 Battery replacement mark flashes 025 E Only E and numerals are displayed Batteries are worn out Trouble caused by abnor mality in function Replace both batteries with new ones Refer to Page 6 Please contact the n
18. ock the settings ALARM SET ALARM SET gt 8 80 6 30 amp ALARM 20 004 20 00 Screen of indicating that the alarm is sounding Alarm Screen 15 Time You can change the time and date setting of your blood pressure monitor TIME SET When reaching the time screen you will see the Gregorian calendar The 2002 di 1 1 year will be flashing N74 N 1 By using the 4 buttons you can set the current year 0 00 2 By pushing the SET button you will lock the year and proceed Time Screen to the next setting For setting the month date and time repeat step 1 and 2 After setting the minutes you will proceed to the DELETE DATA screen DELETE DATA T YES NO 1 N n Delete data All Memory Erasure In this screen you are able to delete all stored measurement from you YES een OMRON 637IT Please be careful that deleted data cannot be restored The factory preset is NO If you choose YES the monitor will ask for a ARE YOU SURE confirmation ARE YOU SURE To cancel select NO to confirm Tyres NO DELETE DATA select YES pis After deleting all stored measurements the Data Deleted Screen will be shown All the stored measurements are deleted and the monitor will be Are You Sure YES turned off Screen If the stored measurements are not deleted you will proceed to the RESET SETTINGS screen C SYS ae M mmHg me DIA mm mm BPH mmHg
19. our PC Main unit Wrist Cuff Battery Cover Systolic Blood Pressure Display Diastolic Blood f AN Pressure Display omnon MA Ince li 637IT p sense i i a Date Time Display gb 1 s 8 m 5 i mrHg 70 DIA BPH mmhg Gd Mark Displayed when a stored measurement is shown Pulse Display d b button Push i to move the displayed item forward Push 4 to move the dis played item backward SETTING button Push this button to set various items on the moni tor such as time and date How to Insert the Batteries Use this monitor after inserting batteries in the main unit 1 a Open the battery compartment 2 a Insert the batteries Type LRO3 AAA as shown in the figure Ensure the polarity of the batteries is correct 3 Close the battery cover MEMORY RECALL button Push this button to see the measured values stored in the monitor GRAPH CALL button Push this button to see the graph ON OFF button Push this button to measure your blood pressure or to switch the moni tor off Please disconnect your 637IT from your PC when you replace the batteries With new batteries long life alkaline batteries you are able to measure app 300 times under normal conditions Please switch of the monitor after using it If you forget to switch the monitor off it will Switch off itself after app 2 minutes Please take the
20. perature of 22 C Operating Temperature and Humidity 10 to 40 C 30 to 85 RH Storage temperature and humidity 20 to 60 C 10 to 95 RH Measurable circumference of wrist 135 to 215 mm Weight of Main Unit Approximately 150 g not including batteries External Dimensions 78 W x 65 5 H x 37 2 D mm not including the wrist cuff Electric Shock Protection Internal power supply appliance type B Accessories Two LRO3 alkaline batteries for monitoring use storage case Instruction Manual USB cable software n the interest of product improvement specifications are subject to change without notice e Type B EU Representative C 0197 OMRON Healthcare Europe B V Kruisweg 577 NL 2132 NA Hoofddorp 25
21. r blood pressure review your health and lifestyle 20 Systolic blood pressure Diastolic blood pressure Blood is pumped out Blood returns to heart Vascular Artery wall Vascular wall Vein Pressure Pressure to to vascular Expansion J vascular wall a wall a drops a K increases t t Lifestyle Excessive intake of salt Excessive consumption of alcohol Obesity Lack of exercise v Hypertension v Arterial sclerosis Danger of Cerebral apoplexy Myocardial infarction Hypertension guide The World Health Organization WHO and the International Society of Hypertension ISH estab lished the Blood Pressure Classification Use this Classification as the guide to know the state of your blood pressure However if you are concerned with your blood pressure be sure to follow the instructions of your doctor There is no universally accepted definition of hypotension Generally speaking those with the Systolic pressure below 100 mmHg are considered to be hypotension Systolic blood pressure mmHg A Severe hypertension 180 Moderate hypertension 160 Mild hypertension Normal systolic value 130 Normal blood pressure 120 Optimal blood Diastolic pressure blood target value pressure gt mmHg 80 85 30 10 10 According to the blood pressure classification by the WHO ISH revised in 1999 International Soci
22. rist height supported by an acoustic sound SIGNAL ON or OFF POSITION SENSOR POSITION SENSOR POSITION SENSOR NL M 4 T ron OFF ON SFF k ON OFF SIGHAL SIGNAL ON OFF ON aF 4 1 N Position Sensor Screen Position Sensor OFF Position Sensor ON and Screen SIGNAL OFF Screen Left or right wrist measurement Normally blood pressure is measured on the left wrist factory preset With your OMRON 637IT you can choose to use the monitor either on your left or right wrist It is recommended to use the same wrist when for optimal comparisons of your blood pressure fluctuations PRIST WRIST piger RIGHT LEFT RIGHT Measuring Wrist Screen Measuring Wrist Right Wrist Screen Alarm Your blood pressure monitor has the possibility to set an alarm twice a day The alarm function can be used to monitor your blood pressure at the same time every day or as a reminder for pill intake The alarm will sound for 2 minutes By pushing the O I button the alarm will stop The alarm will not sound when the blood pressure monitor is used e g for measuring or graph display at the moment the alarm is set You can set the requested hour by pushing 4 b when flashing Press SET to lock the hour and pro ai de ceed with the minutes By pushing the 4 If you can set the minutes Press SET to confirm and to proceed Push either 4 to enable A or disable OK the alarm Press SET to l
23. rten Troubleshooting siiis 24 sion it may cause peripheral circulatory disturbance For these cases blood pres Spare parts and accessories 25 sure may differ greatly between measurement at the wrist and the brachial Specifications scele dst i e rece he 25 Do not use this monitor for the infant or the person who cannot express one s inten tion Dear Customer They may suffer accident or trouble Thank you for purchasing this OMRON product OMRON products are known for their reliability and Do not use this monitor for purposes other than measuring blood pressure advanced technology By buying this OMRON 637IT wrist blood pressure monitor with USB computer interface and position sensor you have chosen for a high quality and innovative instrument We hope You may suffer accident or trouble that you will be fully satisfied with your new blood pressure monitor Please take your time to read Donat use xortable hones near this monitor this instruction manual carefully before using it for the first time If you still have questions The sc ae ma Dersle erroneousi please contact your OMRON dealer or the distributor as mentioned on the packaging They will be y y pleased to help you Do not disassemble or modify the main unit or the wrist cuff of the blood pressure F monitor We wish you a healthy future Correct measurement will be impossible 2 3 Notes on Safety Important instructions for obtaining m
24. st and brachial blood pressure val ues may somewhat get affected by the physiological condi tions at the time of measurement However the blood pres sure values measured at wrist and upper arm usually fluctuate in the same manner Therefore you can check the fluctuation tendency of blood pressure by measuring the wrist blood pressure Differences between blood pressure measured at home and at the doctor s office Normally blood pressure measured at home tends to be lower than when measured at the doctor s office This can be as much as 20 mmHg due to that you feel more relaxed at home and feel slightly tense when visiting the doctor To manage your blood pressure it is important to monitor and register your blood pressure at home Since blood pressure is fluctuating from beat to beat and is influenced by daily activities measure ments can differ from measurement to measurement Maintenance and storage For cleaning the monitor only use a soft lightly moistened cloth Do not use petroleum spirits thinners or similar solvents Stains on the cuff can be carefully removed using a moist cloth and soapy water Do not wash the cuff or make it wet Please make sure no water will enter the main unit Keep your monitor in the storage case protected from extreme temperatures and humidity Do not carry out repairs of any kind yourself If a defect occurs consult your OMRON dealer or dis tributor Please take the batter
25. u have achieved the correct posture you can start the measurement When you measure for the first time the Position Sensor and the Signal will be ON and measuring at the left wrist will be pre set POSITION Push the O I button to activate your 637IT and the Position Sensor be 6A 44444 Screen will be displayed LEFT WRIST v b OQ LEFT WRIST How to Measure Blood Pressure Sustain your elbow with your other hand or a table to avoid movement Adjust the height of your wrist by using your elbow as a fulcrum When the 4 amp will reach the amp signyou will hear a beeping sound indicating that your blood pressure monitor is at the correct height heart height The amp 2 sign will change in the sign and the measurement will start 25 1 8 15 b Q b gt gt LEFT WRIST LEFT WRIST RO WRIST peri p Start Screen Mark Do not move until the measurement results are iren v displayed Progress The screens see picture will be shown during the 25 1 measurement Pulse 8 15 Rate RAA 58 Mark V m mmHg Inflation in Progress Screen ee 18 o DIA T8 When the measurement is finishes the deflation mark v flashed and the cuff deflates Deflation BPH mg Mark Deflation Start Screen 118 mmHg 70 BPH mmHg Measurement Results Display Screen 10 How to enlarge the reading e The results will be shown on
Download Pdf Manuals
Related Search