Omron Healthcare INTELLISENSE BP755 User's Manual
Contents
1. AND THE MEASUREMENT VALUES NOTE If two sets of measurement values are stored in the memory for the 10 minute period the average is based on the two sets of measurement values If one set of measurement value is stored this is displayed as the average 1 Press the Memory Down button C 2 The average value symbol fat appears on the display when the average reading is shown 26 USING THE MEMORY FUNCTION 2 Press the Memory Down button C lt to display the most recent set of measurement values on the screen Press the Memory Up button to display the oldest set of measurement values Alternating display NOTES The date and time are alternately displayed with the measurement values Press the button repeatedly to display the next values Press and hold the button to display the values faster 3 Press the START STOP button to turn the power off 27 USING THE MEMORY FUNCTION TO DELETE ALL VALUES STORED IN THE MEMORY You cannot partially delete values stored in the memory All values will be deleted 1 While holding the Memory Down button C lt press the START STOP button down for more than 2 seconds until the display appears as it does in the following illustration 2 Press the START STOP button to turn the monitor off NOTE The monitor will automatically turn off after five minutes 28 CARE AND MAINTENANCE To keep your digital blood pressure m2. iac d 4 5 Ud 5 a re Tw Hashes g 00 g 00 g 00 24 TAKING A MEASUREMENT 4 When the measurement is complete the arm cuff completely deflates Your blood pressure and pulse rate are displayed 5 Press the START STOP button to turn the monitor off NOTE The monitor will automatically turn off after five minutes SPECIAL CONDITIONS A CAUTION Inflating to a higher pressure than necessary may result in bruising where the cuff is applied If your systolic pressure is known to be more than 220 mmHg press and hold the START STOP button until the monitor inflates 30 to 40 mmHg higher than your expected systolic pressure NOTES Do not apply more pressure than necessary The monitor will not inflate above 299 mmHg When the measurement is complete the arm cuff completely deflates Your blood pressure and pulse rate are displayed 25 USING THE MEMORY FUNCTION Every time you complete a measurement the monitor stores the blood pressure and pulse rate in the memory The monitor automatically stores up to 90 sets of measurement values blood pressure and pulse rate When 90 sets of measurement values are stored the oldest record is deleted to save the most recent values ADVANCED AVERAGING FUNCTION The monitor calculates the average reading based on the three most recent sets of measurement values taken within 10 minutes of the most recent reading TO DISPLAY THE AVERAGE VALUE
3. minutes between measurements The wait time allows the arteries to return to the condition prior to taking the blood pressure measurement You may need to increase the wait time depending on your individual physiological characteristics 8 Keep a record of your blood pressure and pulse readings for your physician A single measurement does not provide an accurate indication of your true blood pressure You need to take and record several readings over a period of time Try to measure your blood pressure at the same time each day for consistency KNOW YOUR UNIT Main Unit Display Start Stop Button Memory Buttons Date Time Setting Button AC Adapter Jack Components Air Tube Thumb Grip Air Plug Connects to Air Jack Arm Cuff OMRON STARTED AC Adapter Instruction Manual Quick Start Guide 8 UNIT DISPLAY Systolic Blood Pressure V1 us Diastolic Blood Pressure UN D Heartbeat Symbol Hypertension Indicator Pulse Display Deflation Symbol 388 a Memory Symbol Average Value Symbol i 1 Co Co Movement Error Symbol ca T co ca Date Time Display Battery Low Indicator Irregular Heartbeat Symbol DISPLAY SYMBOLS IRREGULAR HEARTBEAT SYMBOL QD When the monitor detects an irregular rhythm two or more times during the measurement the Irregular Heartbeat Symbol Q will appear on the display with the measurement
4. values An irregular heartbeat rhythm is defined Normal Heartbeat as a rhythm that is more than 2596 Pulse slower or 25 faster from the average Blood fNJN N N NUN rhythm detected while the monitor is pressure measuring the systolic and diastolic li lar Heartbeat blood pressure rregular Heartbea Short Long If the irregular heartbeat symbol CO Pulse displays with your measurement results Blood NINIS f UN we recommend you consult your pressure physician Follow the directions of your doctor MOVEMENT ERROR SYMBOL The Movement Error Symbol amp is displayed if you move your body during the measurement Please remove the arm cuff and wait 2 3 minutes reapply the arm cuff and take another measurement AVERAGE VALUE SYMBOL l The Average Value Symbol fi is displayed when you press the Memory button The most recent average reading appears on the display screen 10 DISPLAY SYMBOLS HEARTBEAT SYMBOL HYPERTENSION INDICATOR Y TAKING A MEASUREMENT The Heartbeat Symbol 9 flashes on the display during the measurement The Heartbeat Symbol flashes at every heartbeat When the measurement is complete the Heartbeat Symbol flashes on the display with your blood pressure and pulse rate if the reading is above 135 for the Systolic Blood Pressure value and or above 85 for the Diastolic Blood Pressure value USING THE MEMORY FUNCTION The Heartbeat Symbol flashe
5. 4 AA size batteries so the positive and negative polarities match the polarities of the battery compartment as indicated NOTE 4 AA size batteries are not included in this unit 3 Replace the battery cover 15 BATTERY INSTALLATION BATTERY REPLACEMENT X Low Battery Indicator When the Low Battery Indicator appears on the display screen turn the monitor off and remove all the batteries Replace with four new batteries at the same time Long life alkaline batteries are recommended A WARNING If battery fluid should get in your eyes immediately rinse with plenty of clean water Contact a physician immediately NOTES Turn the unit off before replacing the batteries If the batteries are removed while the unit is still on the date and time will be reset to that of the previous use However the measurement results are not deleted When the batteries are replaced you may need to reset the date and time If the year is flashing on the display screen refer to Setting the Date and Time A CAUTION Dispose of the device components and optional accessories according to applicable local regulations Unlawful disposal may cause environmental pollution 16 SETTING THE DATE AND TIME Set the monitor to the current date and time before taking a measurement for the first time If the current date and time are not set correctly the measurement values stored in the memory and the average val
6. HE RIGHT ARM When taking a measurement using the right arm use this instruction for Step 5 Apply the cuff to your right upper arm so the thumb grip is centered on the inside of your inner arm The bottom of the cuff should be approximately 1 2 above your elbow Right Arm Thumb Grip NOTE Be careful not to rest your arm on the air tube This will restrict the flow of air to the cuff 22 TAKING A MEASUREMENT The monitor automatically determines your ideal inflation level In rare circumstances when a higher inflation may be necessary the monitor automatically re inflates the cuff up to 30mmHg higher than the initial inflation and restarts the measurement 1 Sit on a chair with your feet flat on the floor Place your arm on a table so the cuff is level with your heart 23 TAKING A MEASUREMENT 2 Press the START STOP button AII display symbols appear on the screen The cuff starts to inflate automatically As the cuff inflates the monitor automatically determines your ideal inflation level Remain still and do not move your arm until the entire measurement process is completed NOTE To stop the inflation or measurement push the START STOP button The monitor will stop inflating start deflating and will turn off 3 Inflation stops automatically and the measurement is started As the cuff deflates decreasing numbers appear on the display 12 and the Heartbeat Symbol 4 amp
7. OMRON Automatic Blood Pressure Monitor with ComFit Cuff Model BP755 ENGLISH ESPA OL CONTENTS Before Using the Monitor Introduction cedere e E MEE ARX UR MEE SS E 3 Safety Information 1 ossscsceee e oer re Red oat tobe 4 Operating the DEVICE iier pee e RE R4 ER Edd 4 Risk of Electrical Shock ceres creerii ienesa 5 Cate and Maintenance vase t EXPE RUE HR ERE RR ER 6 Before Taking a Measurement sssless lessen 7 Operating Instructions Know Your Unit zoe 4 der eoe eee Rak DE netos 8 Erit Display o geese econ mie x ae a i estes uesv e RU tauren tea ad 9 Display Symbols 45 2 ceeds ea cea adn e ha dense ys 10 Irregular Heartbeat Symbol D 00 0000s eee 10 Movement Error Symbol 8 20 2 0 0 cc eee 10 Average Value Symbol ih eee eee eee 10 Heartbeat Symbol Hypertension Indicator amp 11 Using the AC Adapter sese cia ersigisa iR td CNRC RE 13 Battery Installation en e a eee 15 Setting the Date and Time sees 17 Applying the Arm Cuff 0 0 0 0 eee eee eee 20 Taking Measureinent ierra ERR REA EC aloe 23 Special Conditions iles 25 Using the Memory Function 0 0 cee tensta 26 Care and Maintenance Care and Maintenance 0 0 cece eee eee eka 29 Error Indicators and Troubleshooting Tips 3T FCC Statement ae 2a does wie tert e ERR axes E eR n duets 33 M attanly i
8. asts so the above limitation may not apply to you OMRON SHALL NOT BE LIABLE FOR LOSS OF USE OR ANY OTHER INCIDENTAL CONSEQUENTIAL OR INDIRECT COSTS EXPENSES OR DAMAGES Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which may vary from state to state FOR CUSTOMER SERVICE Visit our web site at www omronhealthcare com Call toll free 1 800 634 4350 34 SPECIFICATIONS Model BP755 HEM 7000 Z4CS Display LCD Digital Display Measurement Range Pressure 0 to 299 mmHg Pulse 40 to 180 min Accuracy Calibration Pressure 3mmHg or 2 of reading Pulse 5 of reading Inflation Automatic by electric pump Deflation Automatic pressure release valve Rapid Air Release Automatic exhaust valve Pressure Detection Capacitive pressure sensor Measurement Method Oscillometric method Pulse Wave Detection Capacitance type pressure sensor Power Source 120V 60Hz AC Adapter or 4 AA batteries Battery Life Approx 1500 uses with 4 new alkaline batteries Operating Temperature 50 F to 104 F 10 C to 40 C 15 to 90 RH Humidity Storage Temperature 4 F to 140 F 20 C to 60 C 10 to 95 RH Humidity Air Pressure 700 1060 hPa Main Unit Weight Approximat
9. e amp Automatic Blood Pressure Monitor excluding the arm cuff is warranted to be free from defects in materials and workmanship appearing within 5 years from the date of purchase when used in accordance with the instructions provided with the monitor The arm cuff is warranted to be free from defects in materials and workmanship appearing within one year from the date of purchase when the monitor is used in accordance with the instructions provided with the monitor The above warranties extend only to the original retail purchaser We will at our option repair or replace without charge any monitor or arm cuff covered by the above warranties Repair or replacement is our only responsibility and your only remedy under the above warranties To obtain warranty service contact Customer Service by calling 1 800 634 4350 for the address of the repair location and the return shipping and handling fee Enclose the Proof of Purchase Include a letter with your name address phone number and description of the specific problem Pack the product carefully to prevent damage in transit Because of possible loss in transit we recommend insuring the product with return receipt requested ALL IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE APPLICABLE WRITTEN WARRANTY ABOVE Some states do not allow limitations on how long an implied warranty l
10. e proper configuration for the power outlet A The power unit AC Adapter is intended to be correctly oriented in a vertical or floor mount position NOTES Use only the authorized Omron AC Adapter that came with this monitor We recommend you install the batteries even if the AC Adapter is used If no batteries are installed you may need to reset the date and time if the AC Adapter is disconnected The measurement results will not be deleted A CAUTION Use only authorized parts and accessories Parts and accessories not approved for use with the device may damage the unit 13 USING THE AC ADAPTER To connect the AC Adapter QD Insert the AC Adapter Plug into the AC Adapter Jack on the back side of the monitor as illustrated Q Plug the AC Adapter into a 120V AC outlet 60 cycles Cord To disconnect the AC Adapter Hold and pull the housing to remove the AC Adapter from the electrical outlet Do not remove by pulling the cord Remove the AC Adapter plug from the monitor A WARNING Do not plug or unplug the power cord into the electrical outlet with wet hands CAUTION Do not overload power outlets Plug the device into the appropriate voltage outlet 14 BATTERY INSTALLATION NOTE Use 4 new AA size batteries long life alkaline batteries are recommended 1 Press the V indicator on the battery cover and slide the cover off in the direction of the arrow 2 Install
11. ely 12 1 2 oz 355 g not including batteries Main Unit Dimensions Approx 6 3 32 I x 5 5 32 w x 3 5 16 h 155 mm x 131 mm x 84 mm Cuff Size Approximately 6 w 152 mm Cuff tube 23 5 8 1 600 mm Cuff Circumference Fits arm circumferences 9 to 17 220mm to 420mm Memory Up to 90 readings Contents Main Unit ComFit Cuff AC Adapter Instruction Manual Quick Start Guide and Storage Case Type B NOTE These specifications are subject to change without notice 35 Manufactured by OMRON HEALTHCARE Made in China Distributed by OMRON HEALTHCARE INC 1200 Lakeside Drive Bannockburn Illinois 60015 www omronhealthcare com Copyright 2009 Omron Healthcare Inc
12. ent or other property A CAUTION OPERATING THE DEVICE A Contact your physician for specific information about your blood pressure Self diagnosis and treatment using measured results may be dangerous Follow the instructions of your physician or licensed healthcare provider A The monitor is not intended to be a diagnostic device A If battery fluid should get in your eyes immediately rinse with plenty of clean water Contact a physician immediately A Read all of the information in the instruction manual and any other literature in the box before operating the unit SAFETY INFORMATION OPERATING THE DEVICE continued A This device is intended for use in measuring blood pressure and pulse rate in the adult population Do not use this device on infants or persons who cannot express their intentions As Read the Special Conditions section page 24 of the instruction manual if your systolic pressure is known to be more than 220 mmHg Inflating to a higher pressure than necessary may result in bruising where the cuff is applied A Operate the device only as intended Do not use the device for any other purpose A Dispose of the device components and optional accessories according to applicable local regulations Unlawful disposal may cause environmental pollution A Do not use a cellular phone near the device It may result in an operational failure A Use only authorized parts and accessories Parts and accessorie
13. ents 30 ERROR INDICATORS AND TROUBLESHOOTING TIPS SYMBOL CAUSE CORRECTION Take another measurement and remain still until the measurement is complete Monitor could not detect pulse wave Cuff under inflated Cuff not applied Remove the arm cuff correctly Read Taking a Measurement Wait 2 3 minutes Cuff over inflated Take another measurement Replace the four batteries Refer Batteries are worn epe to Battery Installation 31 ERROR INDICATORS AND TROUBLESHOOTING TIPS CAUSES AND SOLUTIONS No power Replace all four batteries with new ones No display appears on the unit Check the battery installation for proper placement of the battery polarities Blood pressure varies constantly Many factors including stress time of day how you wrap the cuff may affect your blood pressure Review the sections Before Taking a Measurement and Taking a Measurement Measurement values appear too high or too low 32 FCC STATEMENT Note POTENTIAL FOR RADIO TELEVISION INTERFERENCE for U S A only This product has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation The product generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions
14. may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If the product does cause harmful interference to radio or television reception which can be determined by turning the product on and off the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna ncrease the separation between the product and the receiver Connect the product into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help POTENTIAL FOR RADIO TELEVISION INTERFERENCE for Canada only This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference causing equipment standard entitled Digital Apparatus ICES 003 of the Canadian Department of Communications Cet appareil num rique respecte les limites de bruits radioel ctriques applicables aux appareils num riques de Clase B prescrites dans la norme sur le materiel brouilleur Appareils Num riques ICES 003 dict e par le minister des communications Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 33 WARRANTY LIMITED WARRANTIES Your BP755 IntelliSens
15. onitor in the best condition and protect the unit from damage follow the directions listed below Keep the monitor in the storage case when not in use Make sure the AC Adapter is placed under the main unit so that is does not damage the display Do not forcefully bend the arm cuff or air tube Do not fold tightly Clean the monitor with a soft dry cloth Do not use any abrasive or volatile cleaners Do not attempt to clean the cuff A CAUTION Do not submerge the device or any of the components in water Do not subject the monitor to extreme hot or cold temperatures humidity or direct sunlight A CAUTION Store the device and the components in a clean safe location A CAUTION Do not subject the monitor to strong shocks such as dropping the unit on the floor Remove the batteries if the unit will not be used for three months or longer Always replace all the batteries with new ones at the same time Use the unit consistent with the instruction provided in this manual Use only authorized parts and accessories 29 CARE AND MAINTENANCE Use the unit in a manner consistent with the instructions provided in this manual A CAUTION Use only Omron authorized parts and accessories Parts and accessories not approved for use with the device may damage the unit A CAUTION Changes or modification not approved by the manufacturer will void the user warranty Do not disassemble or attempt to repair the unit or compon
16. s not approved for use with the device may damage the unit A Use only 1 5 V AA alkaline batteries with this device Do not use other types of batteries This may damage the unit RISK OF ELECTRICAL SHOCK A Do not plug or unplug the power cord into the electrical outlet with wet hands A Do not overload power outlets Plug the device into the appropriate voltage outlet SAFETY INFORMATION CARE AND MAINTENANCE A Do not subject the monitor to strong shocks such as dropping the unit on the floor A Do not submerge the device or any of the components in water A Store the device and the components in a clean safe location A Changes or modification not approved by the manufacturer will void the user warranty Do not disassemble or attempt to repair the unit or components BEFORE TAKING A MEASUREMENT To ensure a reliable reading follow these recommendations 1 Avoid eating drinking alcohol smoking exercising and bathing for 30 minutes before taking a measurement Rest for at least 15 minutes before taking the measurement 2 Stress raises blood pressure Avoid taking measurements during stressful times 3 Measurements should be taken in a quiet place 4 Remove tight fitting clothing from your left arm 5 Sit on a chair with your feet flat on the floor Rest your left arm on a table so that the cuff is at the same level as your heart 6 Remain still and do not talk during the measurement 7 Wait 2 3
17. s when the blood pressure reading stored in the memory is above 135 for the Systolic Blood Pressure value and or above 85 for the Diastolic Blood Pressure value 11 DISPLAY SYMBOLS The American Heart Association recommends the following guideline for upper limit of normal for home blood pressure readings AHA Home Guideline for Upper Limit of Normal BP Systolic Blood Pressure 135 mmHg Diastolic Blood Pressure 85 mmHg This is a general guideline because blood pressure depends on age and morbidity The AHA recommends a lower home blood pressure goal for certain patients including diabetic patients pregnant women and patients with renal failure A WARNING The monitor is not intended to be a diagnostic device A WARNING Contact your physician for specific information about your blood pressure Self diagnosis and treatment using measured results may be dangerous Follow the instructions of your physician or licensed healthcare provider Omron Healthcare recommends you contact your physician if the Heartbeat Symbol 99 flashes on the display with your measurement values American Heart Association Scientific Statement 2004 12 USING THE AC ADAPTER IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS DANGER TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK CAREFULLY FOLLOW THESE INSTRUCTIONS A For connection to a power supply not in the U S A use an attachment plug adapter of th
18. se eeu nie eR e b E ep eae HERI 34 Specifications used d genae edet E PS Rte eiden 35 INTRODUCTION Thank you for purchasing Omron BP755 IntelliSense Automatic Blood Pressure Monitor with the ComFit Cuff Fill in for future reference DATE PURCHASED SERIAL NUMBER Staple your purchase receipt here Your new digital blood pressure monitor uses the oscillometric method of blood pressure measurement This means the monitor detects your blood s movement through your brachial artery and converts the movements into a digital reading An oscillometric monitor does not need a stethoscope so the monitor is simple to use The BP755 comes with the following components Monitor ComFit Cuff AC Adapter Storage Case Quick Start Guide nstruction Manual printed in English and Spanish The BP755 IntelliSense Automatic Inflation Blood Pressure Monitor is intended for home use SAVE THESE INSTRUCTIONS 3 SAFETY INFORMATION To assure the correct use of the product basic safety measures should always be followed including the warnings and cautions listed in this instruction manual SAFETY SYMBOLS USED IN THIS INSTRUCTION MANUAL Indicates a potentially hazardous situation A WARNING which if not avoided could result in death or serious injury Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury to the user or patient or damage to the equipm
19. t to advance by increments of one minute Press the Date Time Setting button to set the current minute The year flashes on the display 7 TO TURN THE MONITOR OFF Press the START STOP button NOTE The monitor will automatically turn off after the minute has been set after battery replacement 19 APPLYING THE ARM CUFF A CAUTION Read all of the information in the instruction manual and any other literature in the box before operating the unit A CAUTION This device is intended for use in measuring blood pressure and pulse rate in the adult population Do not use this device on infants or persons who cannot express their intentions APPLYING THE CUFF ON THE LEFT ARM 1 Make sure the air plug is securely inserted in the main unit 2 Remove tight fitting clothing from your upper arm ISN 20 APPLYING THE ARM CUFF 3 Hold the thumb grip on the cuff Thumb Grip securely with your hand Cloth Fastening 4 Turn the palm of your hand upward 5 Apply the cuff to your left upper arm so the blue stripe is on the inside of your arm and aligned with your middle finger The air tube runs down the inside of your arm The bottom of the cuff should be approximately 1 2 above your elbow Left Arm Blue Stripe 1 2 inch 1 2 cm N Air Tube 21 APPLYING THE ARM CUFF 6 Wrap the cuff firmly in place around your arm using the cloth fastening APPLYING THE CUFF ON T
20. ues may not be correct 1 TO START THE SETTING Press the Date Time Setting button C to adjust the date and time The year flashes on the display N 7 20 06 2 SETTING THE YEAR The year can be set between 7 2006 and 2030 LEN When the display reaches 2030 it will return to 2006 Press the Memory Up button C gt to advance by increments of one year Press the Date Time Setting button to set the current year The month flashes on the display NOTES Press the Memory Down button C4 D to decrease the day and time values by increments of one Press and hold the Memory button to increase or decrease the date and time values faster 17 SETTING THE DATE AND TIME 3 SETTING THE MONTH Press the Memory Up button C gt to advance by increments of one month Press the Date Time Setting button to set the current month The day flashes on the display 4 SETTING THE DAY Press the Memory Up button C gt to advance by increments of one day Press the Date Time Setting button to set the current day The hour flashes on the display 5 SETTING THE HOUR The time is set using AM or PM Press the Memory Up button to advance by increments of one hour ui 7 Press the Date Time Setting button to set the current hour The minutes flash on the display 18 SETTING THE DATE AND TIME 6 SETTING THE MINUTE Press the Memory Up button g
Download Pdf Manuals
Related Search