Home
Omega Vehicle Security LVR300 User's Manual
Contents
1. OMEGA is pleased to offer suggestions on the use of its various products However OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance with information provided by OMEGA either verbal or written OMEGA warrants only that the parts manufactured by the company will be as specified and free of defects OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER EXPRESSED OR IMPLIED EXCEPT THAT OF TITLE AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED LIMITATION OF LIABILITY The remedies of purchaser set forth herein are exclusive and the total liability of OMEGA with respect to this order whether based on contract warranty negligence indemnification strict liability or otherwise shall not exceed the purchase price of the component upon which liability is based In no event shall OMEGA be liable for consequential incidental or special damages CONDITIONS Equipment sold by OMEGA is not intended to be used nor shall it be used 1 as a Basic Component under 10 CFR 21 NRC used in or with any nuclear installation or activity or 2 in medical applications or used on humans Should any Product s be used in or with any nuclear installation or activity medical application used on humans or misused in any way OMEGA assumes no responsibilit
2. Compatibles 4 Datalogging Systems A Recorders Printers amp Plotters HEATERS 4 Heating Cable WY Cartridge amp Strip Heaters 4 Immersion amp Band Heaters WY Flexible Heaters 4 Laboratory Heaters ENVIRONMENTAL MONITORING AND CONTROL Zd Metering amp Control Instrumentation A Refractometers 4 Pumps amp Tubing A Air Soil amp Water Monitors 4 Industrial Water amp Wastewater Treatment A pH Conductivity amp Dissolved Oxygen Instruments M 4213 0605
3. of the Programming Position steps noted at left follow these steps to modify the operating parameter 1 Turn the programming ring to the right to Position 2 and then back to Neutral to bring up the editing cursor in the first deci mal place 2 Turning the ring to the right and back to Neutral increases the current decimal place to the next highest value 3 Turning the ring to the left and back to Neutral moves the cur sor on to the next decimal position Repeat step 2 to edit the current position 4 To confirm the new value continue to turn the ring to the left and back to neutral until you cycle through all of the decimal places and the next parameter shows on the display ENTERING ADDITIONAL PROGRAM PARAMETERS After reaching the Code step enter 111 by turning the ring P1 to Neutral and you can access these additional parameters em e 3 1 HHH 2 Inch cm 4 20 mA Time for the mea Switch between inches Switchable to surement to and cm Switch points are 0 20 mA respond seconds e Lg ee 4 HHHH 5 HHHH 6 Inches cm Set the 4 mA level Set the may be higher than 20 mA level the min level converted automatically Returns to regular dis play mode Enter Code 989 to return to Factory Default Settings Step by step program examples are illustrated on the following pages Note During the programming process if there is no new action taken within 30 seconds the sensor will return to measurement display w
4. User s Guide LVR300 Series Shop online at omega con OZOMEGA omega com e mail info omega com For latest product manuals omegamanual info 1809001 1509002 CERTIFIED CERTIFIED CORPORATE QUALITY CORPORATE QUALITY STAMFORD CT MANCHESTER UK LVR300 Series Continuous Level Switch System omega com CEOMEGA OMEGAnet Online Service Internet e mail omega com info omega com U S A ISO 9001 Certified Canada Servicing North America One Omega Drive P O Box 4047 Stamford CT 06907 0047 TEL 203 359 1660 FAX 203 359 7700 e mail info omega com 976 Bergar Laval Quebec H7L 5A1 Canada TEL 514 856 6928 FAX 514 856 6886 e mail info omega ca For immediate technical or application assistance U S A and Canada Mexico Benelux Czech Republic France Germany Austria United Kingdom ISO 9002 Certified Sales Service 1 800 826 6342 1 800 TC OMEGA Customer Service 1 800 622 2378 1 800 622 BEST Engineering Service 1 800 872 9436 1 800 USA WHEN TELEX 996404 EASYLINK 62968934 CABLE OMEGA En Espa ol 001 203 359 7803 e mail espanol omega com FAX 001 203 359 7807 info omega com mx Servicing Europe Postbus 8034 1180 LA Amstelveen The Netherlands TEL 31 0 20 3472121 FAX 31 0 20 6434643 Toll Free in Benelux 0800 0993344 e mail sales omegaeng nl Frystatska 184 733 01 Karvin Cz
5. a es Mating Connector oar M12 x 1 5 position female shielded straight or M12 x 1 5 position female shielded right angle Example of hysteresis setting Hyst 1 Sue Sources Hirschmann Binder Examples with S1 as maximum switching point ae Alarm range rde Connectors amp Cables or and as minimum switching point comparable connector your interface Time All specifications are subject to change without notice Copyright Omega Engineering Inc 4 05 omega com LVR300 Series Programming Positions amp Operation On power up the company logo is displayed followed by the preset level unit measurement Changing the level by float movement will be reflected in the display If the level is at either of the preset switch levels S1 or S2 the upper and lower levels the display will also be alternating between the S1 or S2 status indication with the level reading The Switch Active status is also indicated by a flashing LED By rotating the program ring to Position 1 P1 toward the left and then back to Neutral the pro gram steps to the S1 setting The level for activation of the S1 switch is indicated and may be edited by turning the program ring to the P2 position see below This will highlight the tenths digit The digit value is advancing by alternating the program ring from center to the right P2 position Turning the ring to the P1 position accepts that value and moves to the next di
6. ars and enters the code The next parameter arrives automati cally A J A J X N S lt Cursor flashing O S NOTE If you remain idle in the programming stage for 30 seconds the display indication will return to measurement display without saving your new set tings You will have to cycle through the program again to make your changes All specifications are subject to change without notice In regular display mode again 07070 lt Code 001 Code 0o01 Code 011 07070 lt 1 Code 111 Filter Units Inch cm Output 4 20 mA Inch cm Filter for display and analog output It is a FIFO filter and the time to accomplish the actual measurement value corresponds to the seconds shown in the display Selection of various units inches cm PSI Display and switch points are recalculated automatically Set analog output 4 20 mA or 0 20 mA Start of analog output range in the selected unit End of analog output range in the selected unit To RETURN TO THE Factory DEFAULT SETTING Set the code to 989 All individual parameters are now overwritten OE OMEGA LVR300 Continuous Level Sensor Installation Guide General Information 1 Continuous Level Sensors should be installed rigidly so the float is free to move as the liquid level cha
7. e This affords our customers the latest in technology and engineering OMEGA is a registered trademark of OMEGA ENGINEERING INC Copyright 2005 OMEGA ENGINEERING INC All rights reserved This document may not be copied photocopied reproduced translated or reduced to any electronic medium or machine readable form in whole or in part without the prior written consent of OMEGA ENGINEERING INC Where Do I Find Everything Need for Process Measurement and Control OMEGA Of Course Shop online at omega com TEMPERATURE uF Thermocouple RTD amp Thermistor Probes Connectors Panels amp Assemblies 4 Wire Thermocouple RTD amp Thermistor A Calibrators amp Ice Point References 4 Recorders Controllers amp Process Monitors 4 Infrared Pyrometers PRESSURE STRAIN AND FORCE 4 Transducers amp Strain Gages Load Cells amp Pressure Gages 4 Displacement Transducers 4 Instrumentation amp Accessories FLOW LEVEL 4 Rotameters Gas Mass Flowmeters amp Flow Computers WY Air Velocity Indicators 4 Turbine Paddlewheel Systems A Totalizers amp Batch Controllers pH CONDUCTIVITY 4 pH Electrodes Testers amp Accessories 4 Benchtop Laboratory Meters Controllers Calibrators Simulators amp Pumps 4 Industrial pH amp Conductivity Equipment DATA ACQUISITION 4 Data Acquisition amp Engineering Software 4 Communications Based Acquisition Systems 4 Plug in Cards for Apple IBM amp
8. ech Republic TEL 420 0 59 6311899 FAX 420 0 59 6311114 Toll Free 0800 1 66342 e mail info omegashop cz 11 rue Jacques Cartier 78280 Guyancourt France TEL 33 0 1 61 37 2900 FAX 33 0 1 30 57 5427 Toll Free in France 0800 466 342 e mail sales omega fr Daimlerstrasse 26 D 75392 Deckenpfronn Germany TEL 49 0 7056 9398 0 FAX 49 0 7056 9398 29 Toll Free in Germany 0800 639 7678 e mail info omega de One Omega Drive River Bend Technology Centre Northbank Irlam Manchester M44 5BD United Kingdom TEL 44 0 161 777 6611 FAX 44 0 161 777 6622 Toll Free in United Kingdom 0800 488 488 e mail sales omega co uk It is the policy of OMEGA Engineering Inc to comply with all worldwide safety and EMC EMI regulations that apply OMEGA is constantly pursuing certification of its products to the European New Approach Directives OMEGA will add the CE mark to every appropriate device upon certification The information contained in this document is believed to be correct but OMEGA accepts no liability for any errors it contains and reserves the right to alter specifications without notice WARNING These products are not designed for use in and should not be used for human applications omega com LVR300 Series Sensor Overview Operating Principle mm The complete LVR300 Series Sensor is designed to be a self contained continuous level sen sor and control requiring only a power source A 16 bit microcont
9. git Turning the ring to Neutral and then back to P1 will cycle through all of the digits and then accept the values PROGRAMMING POSITIONS The P1 to Neutral movement steps the program through positions in the following sequence Neutral Program Position 1 Program Position 2 LOGO Logo display only shown on initial power up HHHH Inches cm Current float level At right the switch active status is indicated and alter nates with the regular measurement display and the LED is flashing 4 Switch point 1 value HHHH sets level for activation 4 Switch point 1 is active if the level is below or below S1 Min Max a Hyst 1 Hysteresis threshold added to HHH switch point 1 for switch active a Switch point 2 value HHH sets level for activation Switch point 2 is active if the level is above or below S2 Hysteresis threshold added to switch point 2 for switch active To access other program para lt meters rotate ring to P2 000 and change 000 to 111 Returns to regular display of current float level Inches cm PROTECTING YOUR PROGRAMMING PARAMETERS 1 Pull off the ring Keep it as a personal key 2 Use ring in reverse position on the sensor PROG LOCK position All specifications are subject to change without notice MODIFYING OPERATING PARAMETERS From any
10. ion 1 to begin cycling through these programming parameters Switching points S1 and S2 Hysteresis direction of S1 and S2 Hysteresis Hyst 1 and Hyst 2 Code allows editing of additional parameters Filter Units Output 4 mA Value and 20 mA value See following pages for detailed programming instructions B Editing with Position 2 Turn the programming ring to the right to Position 2 and a flashing cursor appears showing the position to be changed With repeated turning to Position 2 the values are increased By turning to Position 1 you obtain the next position Each position can be edited in this way If there is no Programming Ring turns from Position 1 to Position 2 Terminal Assignment action within 5 seconds the device returns to the normal display sec Garoa A tion without the change being accepted and you will have to cycle S o e o through the program again wr lo bie z Sensor PC o e n C Saving the change with Position 1 HC st e 7 Turning one time toward Position 1 after quitting the last value signifies EC s y acceptance of the change 7 N Value Alarm range Z load Example PNP or NPN Programming protection i The switch points are automatically chang The programming ring can be pulled off EAN ing to positive or negative depending on inverted and replaced This will prevent further programming resulting from turning the ring in either direction v
11. ithout saving your changes You will have to go through the entire program a second time to re program the unit Copyright Omega Engineering Inc 4 05 omega com LVR300 Series Quick Reference Programming Steps HOW TO MODIFY THE SENSOR OPERATING PARAMETERS Example S1 18 6 Inches or cm If the ring is turned right toward Position 2 EDIT a cursor appears while the parameter you want to modify is displayed S1 v 25 5 S1 Turning right effects a change to the next 25 higher figure S1 Turning left moves the cursor to the next deci mal position ooa oY Move ring 3 times to the right alternating to Position 2 and center and you will see a 3 digit increase to the figure marked by the cursor s location i S Turn the ring 2 times to the left toward Position 1 and the cur sor disappears The modified S1 is now vis able and the next para meter is shown automatically HOW TO ENTER ADDITIONAL PARAMETERS amp INFORMATION When the program ring is turned to the right toward Position 2 EDIT a cursor appears at the parameter to modify J Turning right effects an increase of the figure J V 4 Turning left moves the cursor gt to the next deci mal position By turning the ring to the left toward Position 1 the cursor disap pe
12. n Y CEOMEGA Shop online at omega com e mail info omega com For latest product manuals omegamanual info WARRANTY DISCLAIMER OMEGA ENGINEERING INC warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase OMEGA s WARRANTY adds an additional one 1 month grace period to the normal one 1 year product warranty to cover handling and shipping time This ensures that OMEGA s customers receive maximum coverage on each product If the unit malfunctions it must be returned to the factory for evaluation OMEGA s Customer Service Department will issue an Authorized Return AR number immediately upon phone or written request Upon examination by OMEGA if the unit is found to be defective it will be repaired or replaced at no charge OMEGA s WARRANTY does not apply to defects resulting from any action of the purchaser including but not limited to mishandling improper interfacing operation outside of design limits improper repair or unauthorized modification This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence of having been damaged as a result of excessive corrosion or current heat moisture or vibration improper specification misapplication misuse or other operating conditions outside of OMEGA s control Components in which wear is not warranted include but are not limited to contact points fuses and triacs
13. nges 2 Continuous Level Sensors should be mounted in a tank area free of severe turbulence or protected from such turbulence by appropriate and adequate slosh shields 3 Continuous Level Sensors stems should be vertical for best results but satisfactory operation is possible in most liquids with the stem at up to a 30 angle from vertical 4 Care should be taken that Continuous Level Sensors are always operated within electri cal ratings Cautions 1 The pressure temperature and electrical limitations shown for the specified level sensor must not be exceeded 2 The pressures and temperatures must take into consideration possible surges in the temperature and pressure of the system 3 The liquids used must be compatible with the materials of construction Specifications of materials will be given upon request 4 Life expectancy of the sensor varies with applications 5 Ambient temperature changes can affect sensor set points since specific gravities of liquids vary with temperature Consult factory for assistance 6 Level sensors have been designed to be shock and vibration resistant For maximum life both should be minimized Consult factory for assistance 7 Excessive contaminants in fluid may inhibit float operation and occasional wipe down may be necessary 8 Physical damage to product may render product unserviceable 9 Installation in a vessel made from magnetic materials may affect operation omega co
14. roller with a 14 bit A D converter and a 12 bit D A converter provides the necessary processing speed and measurement accuracy The signal is displayed with units using a back lit LCD graphical display and converted to a 4 20 mA signal Two switch points with either a positive or negative output can be programmed over the com plete range The switching point hysteresis can be set separately in value and direction minimum maximum switching value Upward and downward crossings of switching points and error messages are shown in the display with a flashing red LED that is easily visible from a distance Other parameters can be changed using codes including signal filter selectable unit inch cm includes automatic con version of the values selectable 0 20 mA or 4 20 mA output value assignment of 4 20 mA setting of zero point and span The complete housing can be rotated around the mechanical connection so that the correct reading position can be set after mounting installation This LVR300 Series is very easy to use as dialog messages are displayed for the user It can even be set when wearing protective gloves if necessary Programming Overview HE The LVR300 Series programming ring can be rotated from the Neutral center position to Position 1 and Position 2 The following actions are possible A Display of parameters with Position 1 simultaneous display of the set parameters Turn the programming ring left to Posit
15. y as set forth in our basic WARRANTY DISCLAIMER language and additionally purchaser will indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product s in such a manner RETURN REQUESTS INQUIRIES Direct all warranty and repair requests inquiries to the OMEGA Customer Service Department BEFORE RETURNING ANY PRODUCT S TO OMEGA PURCHASER MUST OBTAIN AN AUTHORIZED RETURN AR NUMBER FROM OMEGA S CUSTOMER SERVICE DEPARTMENT IN ORDER TO AVOID PROCESSING DELAYS The assigned AR number should then be marked on the outside of the return package and on any correspondence The purchaser is responsible for shipping charges freight insurance and proper packaging to prevent breakage in transit FOR WARRANTY RETURNS please have the FOR NON WARRANTY REPAIRS consult OMEGA following information available BEFORE for current repair charges Have the following contacting OMEGA information available BEFORE contacting OMEGA 1 Purchase Order number under which the product 1 Purchase Order number to cover the COST was PURCHASED of the repair 2 Model and serial number of the product under 2 Model and serial number of the product and warranty and 3 Repair instructions and or specific problems 3 Repair instructions and or specific problems relative to the product relative to the product OMEGA s policy is to make running changes not model changes whenever an improvement is possibl
Download Pdf Manuals
Related Search
Related Contents
DE EN DRAGON 7 3153 000 0000 4 2 1 3 取り扱い説明書(PDF) 39320D/39320/29320/29320LP - Support iiyama E481S-B 19 INCH MONITOR TFT VGA/DVI SPEAKERS 1280X1024 BLACK CS540™ CS540™ ISTRUZIONI DI MONTAGGIO INSTRUCTION POUR LE MONTAGE Mode d`emploi ARCTIC Land Rider 309 Copyright © All rights reserved.
Failed to retrieve file