Olympus PT-029 User's Manual
Contents
1. 7 This product is an airtight construction made of plastic polycarbonate When it is left for a long time in a car on a boat at the beach or at other places reaching a high temperature or when it is subjected for a long time to uneven external force it may be deformed and the waterproof function may be lost Pay sufficient attention to temperature control Also do not place heavy objects onto the product during storage or transport and avoid unreasonable storage E 4 8 When the O ring contact surface is pressed strongly from the outside of the Case or when the Case is twisted the waterproof function may be lost Take care not to exert excessive force 9 Please use the Case after performing the advance test and the final check 10 If you should notice drops of water or other signs of water leakage while taking pictures immediately stop the dive remove any water from the camera and the product test according to the item Final check and confirm whether leakage has occurred or not Handling the Product Use or storage of the product at the following locations may cause defective operation defects trouble damage fire internal clouding or water leakage Always avoid these locations e Locations reaching high temperatures such as those under direct sunlight in an automobile etc e Locations with open fire e Water depths in excess of 40 m e Locations subject to vibrations e Locations with high temperatures and m2. thinner or other volatile organic solvents or with chemical detergents chemical detergents etc Pure water or lukewarm water is sufficient Do not use anticorrosion agents The metal parts Anticorrosion agent use Stainless steel or brass and washing with pure water is sufficient Commercial defogging Do not use commercial defogging agents Always agents use the specified desiccant silica gel Grease other than specified Use only the specified silicone grease for the silicone grease silicone O ring as otherwise the O ring surface may deteriorate and water leakage may be caused Do not use adhesive for repairs or other purposes Adhesive When repair is required please contact a dealer or a service station of OLYMPUS IMAGING CORP Do not perform operations other than specified in this instruction manual do not remove or modify parts other than specified and do not use parts other than specified Any troubles in taking pictures or with the equipment resulting from the above actions shall be outside the guarantee OLYMPUS IMAGING CORP shall be in no way responsible for accidents involving immersion of a digital camera in water OLYMPUS IMAGING CORP shall not pay any compensation for accidents injury or material damage at the time of use E 6 Contents MOGUCU serons na ice etre arenar TRN a a erie errr re Please read the following items before use FOR safo USE irana annia Batterie en naandaa s
3. 1 Never use alcohol thinner benzene or similar organic solvents or chemical detergents to clean the O ring When such chemicals are used it is to be feared that the O ring will be damaged or that its deterioration will be accelerated 2 Use the original Olympus silicone O ring grease white cap The grease attached to Cases up to PT 008 red cap and the grease of other companies are not suitable for this silicone O ring and use of such grease may cause deterioration of the surface and impairment of the waterproof function 3 In order to avoid deformation of the O ring when the Case is not used for a long time remove the O ring from the Case apply a thin coat of the special grease and store the O ring in a clean plastic bag For reuse confirm that the O ring is free of damage and cracks that it has sufficient elasticity that the surface is free of stickiness and other abnormalities and use it after applying a thin coat of the special grease Excessive application of grease does not improve the waterproof function or the permissible withstand pressure However it may facilitate attachment of sand dirt etc A thin uniform coat produces the best result 4 The O ring is a consumable product Replace it at least once a year 5 Deterioration of the O ring is accelerated by the use conditions and the storage conditions Replace the O ring immediately by a new one if it shows signs of damage cracking or loss of elasticity Q10
4. a fully charged battery before each dive Confirmation of the Remaining Number of Pictures to be Taken Confirm that the image storage has a sufficient remaining number of pictures to be taken Remove the hand strap from the digital camera When a strap is attached to the digital camera the hand strap must be removed A CAUTION When a digital camera is loaded without removing the strap the strap may get caught between the Case lids and may cause water leakage e When removing the strap handle the digital camera with sufficient care OLYMPUS IMAGING CORP shall not be responsible for damage caused by dropping the camera etc E 14 Prepare the camera Which digital cameras can be used This Case PT 029 can only be used with the Stylus 600 DIGITAL 600 camera Turn on the camera Press the digital camera s POWER ON OFF button to turn it ON The camera goes into the standby mode when it hasn t been operated for about 3 minutes Pressing any button such as the zoom button cancels the standby mode If the camera is left for about 15 minutes without being operated the power switches OFF completely to save battery power In this case the camera can be turned ON by pressing the POWER ON OFF button Check camera operation Confirm camera operation as described in the camera s operation manual After completing the check press the camera s power switch to turn it off Open the Case Us
5. accordingly ZA CAUTION lf the camera does not function properly restart the digital camera installation procedure from Check the digital camera on page E 14 of this manual Check the shooting scene and shooting scene mode When the case is used the camera s Shooting scene Scene Shooting mode can be confirmed shooting scene mode with the Scene Shooting mode indicator on the camera s LCD monitor E 19 Installation and Removal of the LCD Hood Installation Strongly push the mounting projections of the LCD hood as shown in the figure into the guides above and below the LCD monitor window Removal Remove the mounting projections of the LCD hood from the guides above and below the LCD monitor window by widening the En LCD hood Guides Installation Removal E 20 Mounting and Removing the Lens Cap Fit the lens cap onto the lens ring as shown in the figure Be sure to remove the lens cap before shooting Perform the final checks Visual Inspection After sealing the Case check the sealing part of front and rear lid visually to confirm that the O ring is not twisted or out of the groove and that no foreign matter has been caught A CAUTION Hairs fibers and other narrow items are not very apparent but they may cause entry of water so that special attention is required E 21 Final Test The final test after loading the cam
6. e The O ring is a consumable product Independent of the number of times the Case is used it is recommended that the O ring should be replaced by a new one at least once a year e Deterioration of the O ring is accelerated by the use conditions and the storage conditions Replace the O ring even before a year has passed if it shows signs of damage cracking or loss of elasticity Note Please use original Olympus products for the silicone O ring grease the silica gel and the O ring These consumable products also can be purchased at an Olympus service station E 32 8 Appendix Q amp Aon the use of the PT 029 Q1 Which digital cameras can be used A1 The The PT 029 is only for the models Stylus 600 u DIGITAL 600 Q2 What cautions must be observed when loading the digital camera into the Case A2 Pay special attention to the following items when loading the camera En into the Case 1 Check that the remaining capacity of the battery in the digital camera is sufficient This should be checked as the LCD monitor is used under water and the battery consumption becomes faster 2 Check the remaining number of pictures on the image storage Please use a card with a sufficient remaining number in order to reduce the number of times the Case has to be opened and closed 3 Remove the strap from the digital camera When the camera is loaded without removing the strap the strap may get caught when the Case is seal
7. in this product Storage with a battery inserted may lead to leakage of the battery liquid and fire 3 If leakage of water should occur with a camera installed in this product quickly remove the battery from the camera There is the possibility of ignition and explosion from generation of hydrogen gas 4 This product is made of resin There is the possibility that injuries may be caused when it becomes broken because of strong impact with a rock or other hard objects Please handle with sufficient care 5 The silica gel and the grease for silicone O rings for this product are not edible A CAUTION 1 Do not disassemble or modify this product This may cause water leakage or trouble In case of disassembly or modification by persons other than those appointed by OLYMPUS IMAGING CORP the guarantee shall not apply 2 Do not place this product at locations with abnormally high or abnormally low temperatures or at locations with extreme temperature changes The product may deteriorate 3 Opening and closing at locations with much sand dust or dirt may impair the waterproof characteristic and cause water leakage This should be avoided 4 This product has been designed and manufactured for use at a water depth within 40 m Please note that diving to a depth in excess of 40 m may cause permanent deformation or damage to the Case and the camera inside the Case or may lead to water leakage E 2 5 Jumping into the water with the Ca
8. is outside the specified groove e O ring damage cracks deterioration or deformation e Sand fibers hair or other foreign matter sticking to the O ring the O ring groove or the O ring contact surface on the front lid e Damage to the O ring groove or the O ring contact surface on the front lid e When closing the Case check for catching of the hand strap and silica gel after the above causes have been eliminated A CAUTION The most suitable method for checking water leakage is to immerse the Case to the intended water depth When this is difficult water leakage also can be checked at a shallow depth with no water pressure Do not feel that this is troublesome but perform this test e lf the advance test should show water leakage with normal handling stop using the Case and contact your dealer or an Olympus service station listed on the rear page of this instruction manual E 13 3 Install the digital camera Check the digital camera Check the digital camera before loading it in the Case Battery Confirmation As the LCD monitor is used for picture confirmation while taking pictures under water the battery life becomes short Confirm that the remaining battery capacity is sufficient Do not use alkaline batteries as it is quite possible that they will become unusable during a dive Note In order to avoid losing shutter chances due to an exhausted battery you should always replace a battery with
9. operation parts marked by corresponds to the operation parts of the digital camera When the operation parts of the Case are operated the corresponding functions of the digital camera will operate For details of the functions refer to the instruction manual for the digital camera E 10 Install the strap Install the strap on the Case body Installation explanation Finished installation x Hand strap ring Hand strap A CAUTION Please install the strap correctly as shown above OLYMPUS IMAGING CORP shall bear no responsibility for damage etc caused by dropping the Case because of incorrect installation of the strap Master the basic operation Please master the basic operation of the Case before taking pictures Holding the Case Hold the Case securely with both hands keep your elbows close to your body and hold the Case so that you can confirm the picture on the LCD monitor of the digital camera through the LCD monitor window of the Case Good example Bad example A CAUTION Do not exert excessive force onto the lens window or the lens ring e Take care not to put your fingers etc over the lens window and the flash diffuser How to Press the Shutter J When pressing the shutter lever press it gently so that there will be no movement of the camera Note For detailed operation of the shutter refer to the instruction manual for the digi
10. Instruction Manual Underwater Case PT 029 For the digital camera Stylus 600 u DIGITAL 600 E Thank you for buying the Underwater Case PT 029 E Please read this instruction manual carefully and use the product safely and correctly E Please keep this instruction manual for reference after reading it E Wrong use may cause damage to the camera on the inside from water leakage and repair may not be possible E Before use perform an advance check as described in this manual OLYMPUS IMAGING CORP Introduction Unauthorized copying of this manual in part or in full except for private use is prohibited Unauthorized reproduction is strictly prohibited OLYMPUS IMAGING CORP shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from unsuitable use of this product OLYMPUS IMAGING CORP shall not be responsible for damage lost profits etc caused by loss of image data because of defects disassembly repair or modification of this product by people other than third parties specified by OLYMPUS IMAGING CORP or for other reasons Please read the following items before use This Case is a precision device designed for use at a water depth within 40 m Please handle it with sufficient care Please use the Case correctly after sufficient understanding of the contents of this manual in regard to handling of the Case checks before use maintenance a
11. What are the important points for Case maintenance A10 Please observe the following items 1 Never use the following chemicals for cleaning corrosion protection defogging repair or other purposes Never use alcohol thinner benzene or similar volatile organic solvents or chemical detergents to clean the Case Pure water or lukewarm water is sufficient for cleaning Do not use anticorrosion agents on the metal parts The metal parts are made of aluminum brass or stainless steel Cleaning with pure water is sufficient Do not use commercial defogging agents Always use the original E 36 Olympus defogging silica gel Do not use adhesive for repairs or other purposes When repair is required please contact a service station of our company or your dealer Q11 Please tell me about repairs A11 Please contact a service station of our company or your dealer if repair should be necessary Do not try to repair disassemble or modify the Case yourself Repair disassembly or modification by you or third parties not authorized by Olympus invalidates the guarantee Q12 What are the model names of the accessories for the PT 029 A12 The following accessories are being sold 1 O ring for the PT 029 body POL 029 This is a silicone rubber O ring packing to be installed in the PT 029 body to make it waterproof O rings for other Case models cannot be used 2 Silicone O ring grease PSOLG 1 This is a special grease for sil
12. allation and Removal of the LCD Hood eee E 20 Installation REMOVAl se2cleeisc22 desea ai Mounting and Removing the Lens Cap E 21 Perform the final checks c ccecceeeceeeeeeeeeeeeeeeeeeeeeeeseeeeeaeees E 21 Visual Inspection au Final TeSt sich deck dis Audis eatiain did Adalat 4 Taking Pictures Under Water 0 0 eee E 23 How to Use the Hand Strap cceececcceceseeeeeeeeeeeeeeeeeeeeeeeeeeees E 23 Take pictures carefully t ccisconsoncsneeetteetin nnani E 23 Confirm the picture on the LCD monitor ae Quietly press the shutter lever 0 a Cautions when using the flash eee eee eeeee teens 5 Underwater Shooting According to the Scene Type E 24 Underwater shooting Modes cccececeeeeeeeeeeeeeeeeeeeeeeeeeeees E 24 Selecting the shooting scene mode E 25 Locking AF during underwater shooting c eee E 25 6 Handling After Shooting 0 0 0 ccccceeeteees E 26 Wipe off any waterdrop E 26 Take out the digital camera E 27 Wash the Case with pure water E 28 Dry Ihe Cases marssin E NE E 28 7 Maintaining the Waterproof Function E 29 Remove the O ring Betas TEE E 29 Remove any sand dirt etc E 29 Install the O ring eseese E 31 How to Apply Grease to the O ring Replace consumable products Bi ADDENGIX i525 dchn dedicate ores E 33 Q amp A on the use of the PT 029 oo eeeeceeee
13. and levers under water to turn the shafts and wash off any salt After washing use a dry cloth without any salt on it to wipe off any moisture and dry the Case in the shade Do not use hot air from a hair drier or the like and do not dry the Case under direct sunlight Exposure to high temperatures or direct sunlight may cause deformation discoloration or breakage E 34 Q6 A6 E 2 3 4 Q7 A7 Q8 A8 1 2 3 4 5 6 of the Case and deterioration of the O ring Wipe the inside of the Case with a soft cloth not causing any fibers Remove the O ring wipe off any salt sand dust etc and also clean the O ring groove and the O ring contact surface in the same way and then dry them When an object with a sharp tip is used to remove the O ring from the groove the O ring may be damaged and water leakage may be caused Always use the provided O ring remover How should take pictures under water Please observe the following items for shooting under water Fix the protector with the accessory hand strap to your wrist When you place a finger onto the lens window the finger will appear in the photo Pay attention to the position of your fingers when holding the Case When pressing the shutter lever hold the Case securely with both hands and operate the lever quietly to prevent camera shake Check the image you want to shoot by viewing the digital camera s LCD monitor through the Case s LCD moni
14. auce atest a anan aad EE il Setting the underwater shooting scene MOdE eee eee E 3 For Prevention of Water Leakage Accidents Handling the Product assiso iuerre Contents re 1 PreparationS 2 0 0 inieriopenroereaiareneeureereksnksekienssas Check the contents of the package Names of the parts 0 0 Install the strap ww Master the basic operation Holding the Case 4 How to Press the Shutter Using the Shooting mode SCENE button How to Use the Zoom BUttOns 0 eee ee cece eee eeeeeeeeeeee 2 Advance Check of the Case eee Advance test before use Advance TeSt csceeeseseee 3 Install the digital camera 0 0 cc eee E 14 Check the digital camera seesseseesereerereersesrererrsersisrsrrrrerneeee E 14 Battery Confirmation svesni E 14 Confirmation of the Remaining Number of Pictures to be Taken E 14 Remove the hand strap from the digital camera E 14 Prepare the Camera snr Grninvia as E 15 Which digital cameras can be used ERIO Turn on the camera oo cece E 15 Check camera operation E 15 Open the Case essssesrserirere E 15 Put the digital camera into the case E 16 Insertion of silica gel ele Check the loading status E 18 Seal the Case isitin aiana E 18 Perform the final checks after loading 00 E 19 Check the shooting scene and shooting scene mode E 19 E 7 Inst
15. e groove How to Apply Grease to the O ring Apply the x Make sure that your fingers and the O 1 exclusive 4 ring are free of dirt and squeeze about lubricant to each 5 mm of lubricant onto a finger 5 mm O ring is the most appropriate amount Surround the lubricant with three 2 a Ber fingers and spread it over the ring Be the O rin careful not to use excessive force as 9 this may stretch the O ring Bang S visualy ord by touch that the Oting ie not rind i visually y tou ring i 3 is ke mega scratched and that its surface is flat If it is scratch or damaged in any way replace it with a unevenness brand new O ring Use the lubricant remaining on the fingers to clean and lubricate the case s contact surface Apply lubricant on 4 the O ring contact surface A CAUTION Always perform maintenance of the waterproof function even when the Case has been opened to exchange the battery or the image storage during shooting Neglecting this maintenance may become the cause of water leakage When the Case is not to be used for a long time remove the O ring from the groove to prevent deformation of the O ring apply a thin coat of silicone grease and store it in a clean plastic bag or the like e When drying is done with salt attached it is likely that a function impairment will be caused After use always wash off any salt E 31 Replace consumable products
16. e inside when the Case is opened Take special care to wipe off all waterdrops e When opening the Case take sufficient care that no water will drop from your hair or body onto the Case and the camera e Before opening the Case make sure that your hands or gloves are free of sand fibers etc Do not open or close the Case at locations where water or sand is to be sprayed When this cannot be avoided because you have to exchange the battery or the image storage place a sheet downwind from some object and take care that no water or sand is sprayed e Take care not to touch the digital camera or the battery with hands wet with sea water Note e Moisten a towel etc in advance with pure water and keep it in a plastic bag so that you can wipe the salt from your hands and fingers before handling the camera E 26 Take out the digital camera Open the Case carefully and take the digital camera out A CAUTION Always place the opened Case with the O ring side facing up If the Case is placed with the O ring side facing down dirt or other foreign matter may get on the O ring or the O ring contact surface and may allow water penetration during the next dive e For details on storage of pictures and other details refer to the digital camera s operation manual E 27 Wash the Case with pure water After use seal the Case again aft
17. e the provided O ring remover as described below Insert the hook section below the buckle lock unlock lever Slowly pull the O ring remover If the O ring remover is not available push the buckle lock unlock lever from the left and right with your thumb and index finger and pull up the lever gently E 15 Put the digital camera into the case Make sure the digital camera is turned off then insert it gently into the case A CAUTION If the digital camera is not inserted properly it may not be possible to seal the case so that it is airtight Alternatively some controls may become inoperable Note that imperfect sealing may result in water penetration E 16 Insertion of silica gel Before sealing the Case insert the accessory silica gel bag for prevention of fogging between the bottom of the camera and the Case Pay attention to the orientation A CAUTION Insert the silica gel all the way at the specified location and with the specified orientation When the orientation is not correct the silica gel bag will be caught when the Case is sealed and water leakage will be caused e When it is tried to seal the Case with the bag inserted only part of the way the silica gel bag will be caught by the O ring and water leakage will be caused e Once silica gel has been used the moisture absorption performance will be impai
18. ed and this will cause water leakage 4 Before sealing the Case confirm that the O ring has been installed properly in the groove in the rear lid of the Case 5 Confirm that the O ring and the O ring contact surface on the front lid are free of dirt hairs and other foreign matter 6 Insert the silica gel for defogging Please use silica gel for the Olympus Case Q3 What cautions must be observed when using and storing the Case A3 Pay special attention to the following items 1 When the O ring contact surface is pressed strongly from the outside of the Case or when the Case is twisted the waterproof function may be impaired and water leakage may be caused 2 When the Case is used left or stored at the following locations defective operation or trouble may be caused Always avoid such locations a Places where the Case can reach high temperatures under direct sunlight or in a car places with extremely low temperatures and places with extreme temperature variations b Places with open fire c Places with volatile substances d Places with vibrations E 33 3 In case of the following handling with a camera loaded into the Case trouble or breakage may be caused for the Case and or the loaded camera Always avoid such handling a Hitting other objects b Dropping c Placing heavy objects on top of the Case 4 When the Case is not used for a long time trouble from Q4 Q5 A5 f
19. eeeeeteeeeeeeeeeneaes E 33 SPeCiliCationS sasis lei eurenean Ea AEE EE EAA ances E 38 E 8 1 Preparations Check the contents of the package Check that all accessories are in the box Contact your dealer if accessories should be missing or damaged LCD hood on the body Check that the O ring is normal Instruction manual this manual Silica gel Silicone grease E O ring remover Authorised distributors list Authorised service centres list DIGITAL CAMERA Names of the parts Palm grip Hand strap ring 1 AF LOCK Note 1 Diffuser plate amp Loading guide rail Cross Cursor button diffuser plate cover LCD inner hood 3x Exposure correction Cross Shutter lever O ring cursor button POWER ON OFF button 4 Tripod mount Flash mode Cross cursor button Accessory mount Light shield hood OK MENU button Front lid LCD hood DISP button Buckle hook x Play button x6 Erase button Buckle lock unlock lever x Zoom buttons LCD monitor window Lens cap strap gt Shooting mode P AUTO Rear lid Lens cap SCENE button 83 LCD hood strap Lens window 3 Macro Cross Cursor button amp Silicone O ring grease Lens ring he The Dom man tmecce Silica gel B Hand strap LOCK button in the underwater wide 66 O ring remover angle 1 and underwater macro modes Note The Case
20. ention of Water Leakage Accidents When water leakage occurs while this product is being used repair of the camera housed in this product may become impossible Please observe the following cautions for use 1 When sealing this product make sure that no hairs fibers sand particles or other foreign matter stick not only to the O ring but also to the contact surface flat part of the front cover Even a single hair or a single grain of sand may cause water leakage Please check with special care lt Examples for foreign matter sticking to the O ring gt gt Hair Fibers Grains of sand 2 The O ring is a consumption product Please replace it at least once a year by new one Also perform maintenance for every use 3 Deterioration of the O ring will progress according to the use conditions and the storage conditions Immediately replace the O ring by a new one if it is damaged shows cracks or has lost its elasticity 4 At the time of O ring maintenance clean the inside of the O ring groove and confirm the absence of dirt dust sand and other foreign matter 5 Apply the specified silicone O ring grease to the O ring 6 The waterproof function is not effective when the O ring is not installed correctly When installing the O ring take care that it does not project from the groove and that it is not twisted Also when sealing the Case close the lid after confirming that the O ring has not come out of the groove
21. er taking out the camera and wash it sufficiently in pure water as soon as possible After use in sea water it is effective to immerse it for a fixed time in pure water to remove any salt A CAUTION Water leakage may be caused when a high water pressure is applied locally Before washing the Case with water take out the digital camera from it e Operate the shutter lever and various buttons of this product in pure water to remove salt adhering to the shaft Do not disassemble for cleaning Drying the Case with adhering salt may impair the function Always wash off any salt after use Dry the Case After washing with pure water use a soft cloth without any salt on it and not causing any fibers to wipe off any waterdrop and dry the Case completely at a well ventilated location in the shade A CAUTION Do not use hot air from a hair drier or the like for drying and do not expose the Case to direct sunlight as this may accelerate deterioration and deformation of the Case and deterioration of the O ring leading to leakage of water When wiping the Case take care not to cause scratches E 28 7 Maintaining the Waterproof Function Remove the O ring Open the Case and remove the O ring from the Case Removal of the O ring Insert the O ring remover between the O ring and the O ring groove Pass the tip of the inserted O ring remover below the O ring Be careful not to scratch t
22. era is explained below This is the only way to eliminate worry about possible entry of water Always perform this test It can be performed easily in a water tank or a bathtub The required time is about five minutes Simple water immersion test Explanatory image Hints As the Case is transparent waterdrops entering into it can be confirmed easily ED In case of trouble with the O ring three seconds are enough for water to enter Are there air bubbles coming out between the lids Please check carefully Remove the Case from the water and check that no water has accumulated at the bottom of the Case Is there any water trickling down 1 Place the Case slowly into the water At first immerse the 2 Case for only three seconds Check that no water 3 has entered into the Case Next immerse the 4 Case for 30 seconds Check carefully for air bubbles Do not perform any operation yet but just observe Remove the Case from the water and check that no water has accumulated at the bottom of the Case Perform very careful confirmation Check carefully for air bubbles Hy operation of the buttons used frequently Check carefully for air bubbles 5 Check that no water has entered Next check by 6 immersing for three minutes If there is still no entry of water everything is OK feng 7 This is very important This is the fina
23. he O ring groove with the tip of the O ring remover Hold the O ring with your fingertips after it has come out of the groove and remove it from the Case Remove any sand dirt etc After visually checking that dirt has been removed from the O ring checking for attached sand and other foreign matter as well as for damage and cracks can be done by squeezing the entire circumference of the O ring lightly with your fingertips E 29 Remove any foreign matter attached to the O ring groove using a lint free clean cloth or cotton swab Also remove any sand or dirt attached to the O ring contact surface on the front lid of the case A CAUTION When a mechanical pencil or a similar other sharp object is used to remove the O ring or to clean the inside of the O ring groove the Case and the O ring may be damaged and water leakage may be caused e When the O ring is checked with the fingertips take care not to stretch the O ring e Never use alcohol thinner benzene or similar solvents or chemical detergents to clean the O ring When such chemicals are used it is to be feared that the O ring will be damaged or that its deterioration will be accelerated E 30 Install the O ring Confirm that no foreign matter is attached apply a thin coat of the accessory grease to the O ring and fit the O ring into the groove At this time confirm that the O ring does not stick out from th
24. he case to set the camera to the SCENE mode When the mode selection display appears press the cross cursor Up or Down button to select Underwater Wide Angle 1 Underwater Wide 1 Shooting scene display 2 Shooting scene Angle 2 or Underwater Macro Press 2 lt TOAS RGN the OK MENU button to enter the zs ee ae selection Locking AF during underwater shooting When Underwater Wide Angle 1 or Underwater Macro is selected the cross cursor Down button on the case functions as the AF LOCK button Pressing the button once activates the AF lock mode With focus locked you can concentrate on operating the shutter whenever a perfect picture opportunity arises Functions as the AF LOCK button in the Underwater Wide Angle 1 and Underwater Macro modes Note To cancel the AF lock status press the down cross cursor button AF LOCK again For details refer to the digital camera s operation manual E 25 6 Handling After Shooting Wipe off any waterdrop After completing the shooting and returning to land wipe off any waterdrop sticking to the Case Use air or a soft cloth not leaving any fibers to thoroughly wipe any waterdrop etc from the joint between the front and rear lid the shutter lever the palm grips and the buckles Z CAUTION Especially when waterdrops remain between the front and the rear lid they may spill to th
25. icone O ring maintenance 3 Silica gel SILCA 5S This is a desiccant used to prevent fogging of the glass parts of the Case The quantity is five bags 4 LCD hood PFUD 05 This hood is installed on the LCD monitor window of the Case to make it easier to see the LCD monitor of the camera You can order in large computer shops and camera mass sale stores Please contact your dealer or a service station of our company when replacement is required Replacement will be made against payment The PT 029 is not provided with a balance weight When underwater with digital camera mounted the PT 029 has slightly negative buoyancy E 37 Specifications Available models Olympus digital camera Stylus 600 u DIGITAL 600 Pressure resistance Depth of up to 40 m Main materials Body Transparent polycarbonate Buckles Stainless steel Grip Shutter lever Red polycarbonate Lens window FL glass Operation buttons Stainless steel Nickel plated brass Dimensions Width 130 7 mm x height 96 0 mm x thickness 89 5 mm projections not included Weight 320 g camera and accessories not included We reserve the right to change the external appearance and the specifications without notice E 38 OLYMPUS http www olympus com OLYMPUS IMAGING CORP Shinjuku Monolith 3 1 Nishi Shinjuku 2 chome Shinjuku ku Tokyo Japan OLYMPUS IMAGING AMERICA INC Two Cor
26. l check f Has the silica gel become moist 7 Has the silica gel Please check carefully become moist A As the inside can be seen the inspection for entry of water also can be made securely Now everything is all right 8 Now everything is Have a nice dive all right Note The PT 029 is not provided with a balance weight E 22 4 Taking Pictures Under Water How to Use the Hand Strap Pass your hand through the accessory hand strap and adjust the length with the stop button Take pictures carefully Confirm the picture on the LCD monitor Note that when this Case is used the shooting scene can be confirmed only on the LCD monitor Quietly press the shutter lever When pressing the shutter lever hold the Case securely with both hands and operate the lever quietly to prevent camera shake Cautions when using the flash When taking macro pictures on the wide angle side the flash light may be missing in some parts or the light volume may not be uniform Flash reaching range W Approx 0 2 m to 4 0 m Land shooting without the Case T Approx 0 2 m to 2 5m During underwater shooting shooting conditions water clarity suspended matter etc can have a significant effect on the range of the flash Always check your pictures on the LCD monitor after shooting Pressing the play button puts the camera in play mode To return it to the Shooting mode press the Sho
27. nd storage after use OLYMPUS IMAGING CORP shall in no way be responsible for accidents involving immersion of a digital camera in water OLYMPUS IMAGING CORP shall not pay any compensation for accidents injuries or material damage at the time of use Before use be sure to read the precautions printed on the package For safe use This instruction manual uses various pictographs for correct use of the product and to prevent danger to the user and other persons as well as property damage These pictographs and their meanings are shown below This indicates contents for which the possibility of A WARNING human death or severe injury in case of handling under disregard of this indication can be assumed ACAUTION This indicates contents for which the possibility of human injury or the possibility of material damage in case of handling under disregard of this indication can be assumed A WARNING 1 Keep this product out of the reach of babies infants and children There is the possibility of occurrence of the following types of accidents e Injury by dropping onto the body from a height e Injury from parts of the body getting caught in parts which open and close e Swallowing of small parts Please consult a physician immediately if any parts have been swallowed e Triggering of the flash in front of the eyes may cause permanent vision impairment etc 2 Do not store with a battery in the digital camera housed
28. ormation of mold etc may be caused Before use confirm the operation of all operation parts and perform the advance test and the final test What cautions must be observed when opening and closing the Case Pay special attention to the following items Do not open and close the Case at locations with water spray or sand spray Wipe off all waterdrops from the gap between the front lid and the rear lid and around projections and recesses such as the buckles When this is not done entry of waterdrops into the Case is to be feared at the time of opening and closing When opening the Case take care that no water will drip from your hair or body into the Case or onto the camera When the Case is open check that there is no attachment of sand fibers or other foreign matter to the O ring and the O ring contact surface on the front lid Do not touch the camera or the image storage with your hands to which sea water is sticking If you should detect waterdrops or other signs of water leakage while shooting immediately end the dive perform the water leakage test again and confirm that there is no leakage If the camera is wet wipe off any moisture and check the operation How should the Case be handled after use After use take out the camera as soon as possible and wash the Case with pure water In case of use in the ocean it is effective to immerse the Case for a certain time in pure water to remove any salt Operate the buttons
29. oting mode SCENE button E 23 5 Underwater Shooting According to the Scene Type The camera incorporates the following shooting scene modes Select the one best suited to the underwater scene you are shooting Underwater shooting modes Underwater Wide Angle 1 Suitable for shooting a scene that extends across a wide range such as a school of fish swimming through the water Background blues are vividly reproduced 22 Underwater Wide Angle 2 Suitable for shooting a large slowly moving subject such as a dolphin or manta In many dolphin watching locations use of a flash is not permitted to avoid frightening the dolphins Although this mode was originally designed to work without the flash it can also be enabled if required for example when shooting a manta Underwater Macro Suitable for close up shooting of small fish and other underwater creatures Natural colors underwater are accurately reproduced Red tones can be enhanced by using the flash Examples TIP e When the Underwater Wide Angle 1 or Underwater Macro scene mode is selected you can easily lock the focus position AF lock operation by pressing the cross cursor Down button AF LOCK button on the rear of the protector When the focus is locked the AF lock indicator appears on the top left of the LCD monitor screen of the camera E 24 Selecting the shooting scene mode Press the Shooting mode SCENE button on t
30. porate Center Drive P O Box 9058 Melville NY 11747 9058 U S A Tel 631 844 5000 Technical Support USA 24 7 online automated help http Awww olympusamerica com support Phone customer support Tel 1 888 553 4448 Toll free Our phone customer support is available from 8 am to 10 pm Monday to Friday ET E Mail distec olympus com Olympus software updates can be obtained at http www olympus com digital OLYMPUS IMAGING EUROPA GMBH Premises Wendenstrasse 14 18 20097 Hamburg Germany Tel 49 40 23 77 3 0 Fax 49 40 23 07 61 Goods delivery Bredowstrasse 20 22113 Hamburg Germany Letters Postfach 10 49 08 20034 Hamburg Germany European Technical Customer Support Please visit our homepage http Mwww olympus europa com or call our TOLL FREE NUMBER 00800 67 10 83 00 for Austria Belgium Denmark Finland France Germany Italy Luxemburg Netherlands Norway Portugal Spain Sweden Switzerland United Kingdom Please note some mobile phone services provider do not permit access or request an additional prefix to 800 numbers For all not listed European Countries and in case that you can t get connected to the above mentioned number please make use of the following CHARGED NUMBERS 49 180 5 67 10 83 or 49 40 237 73 899 Our Technical Customer Support is available from 9 am to 6 pm MET Monday to Friday 2005 OLYMPUS IMAGING CORP
31. red Always exchange the silica gel when the Case is opened and closed E 17 Check the loading status Always perform the following final checks before sealing the Case e Has the digital camera been inserted properly e Has the silica gel been inserted all the way at the specified position e Has the O ring at the Case opening part been installed properly e Are the O ring and the O ring contact surface on the front lid free of dirt and other foreign matter Seal the Case When the rear lid is closed quietly so that the O ring will not come out of the groove the buckles are engaged with the edge of the rear lid and the buckle lock levers are pushed down in arrow direction the Case will be sealed airtight A CAUTION Seal the Case by turning both buckle lock levers down in arrow direction When one of the buckles is left open the Case will not be sealed and water leakage will be caused Perform the final checks after loading After sealing the case perform the following final checks to confirm proper operation of the camera e Push the POWER ON OFF button on the case to see if it can turn the camera ON and OFF e Push the Shooting mode SCENE button on the rear of the case to see if it can switch the camera s Shooting mode properly e Press the Case s shutter level and see if the camera shutter can be released accordingly e Press other buttons on the Case to see if the camera functions
32. se in your pocket or in your hand throwing the Case from a boat or ship into the water and other rough handling may cause water leakage Please handle with sufficient care when handing it over from hand to hand etc 6 If the camera on the inside should become wet because of water leakage etc immediately wipe off all moisture and confirm the operation 7 Please remove the O ring when traveling by air Otherwise air pressure may make it impossible to open the Case 8 For safe use of the digital camera in this product please read the Instruction Manual for the digital camera carefully 9 When sealing this product take sufficient care that no foreign matter gets caught at the O ring and the contact surfaces Batteries Please use one Olympus lithium ion rechargeable battery for cameras LI 12B Take care that the battery electrodes do not become wet This may cause trouble or accidents Carefully read the instruction manual for the camera about other cautions regarding batteries Setting the underwater shooting scene mode The Stylus 600 p DIGITAL 600 camera includes scene modes expressly configured to optimize wide angle and macro shooting under water Select the mode according to the scene you want to shoot under waiter For details see Underwater Shooting According to the Scene Type in this manual page E 24 For details on mode setting refer to the digital camera s operation manual E 3 For Prev
33. tal camera Using the Shooting mode SCENE button Press the Shooting mode SCENE button to switch the digital camera between the Shooting mode P AUTO and SCENE mode Each press of the button toggles between the Shooting mode P AUTO and SCENE mode The selected mode can be checked on the LCD monitor How to Use the Zoom Buttons 2 ANA Zoom operation is possible by pressing the zoom buttons on this Case that correspond to the zoom buttons on the digital camera inside the Case 2 Advance Check of the Case Advance test before use This Case has been the subject of thorough quality control for the parts during the manufacturing process and thorough function inspections during the assembly In addition a water pressure test is performed with a water pressure tester for all products to confirm that the performance conforms to the specifications However depending on the carrying and storage conditions the maintenance status etc the waterproof function may be damaged Before diving always perform the following advance test and the water leakage test after installation of the camera Advance Test 1 Before installing the digital camera in the Case immerse the empty Case to the intended water depth to confirm that there is no water leakage 2 Main causes of water leakage are as follows e The O ring has not been installed e A part of the O ring or the entire O ring
34. tor window and start shooting To avoid interruption of shooting due to battery depletion it is recommended to replace the existing battery with a fully charged battery before diving can check for water leakage For confirmation perform the advance test and the final test after loading the camera The advance test with immersing the Case without the camera to the intended use depth to check for water leakage is the most accurate test but when this is difficult it is safer to perform this test even at a depth of 1 m or in a bathtub The final test also can be performed in a bathtub or a bucket What are the causes for entry of water The main causes for the entry of water are shown below Please check them most carefully Forgetting to install the O ring The O ring is partly or completely outside the groove Damage deterioration or deformation of the O ring Sand fibers hair or other foreign matter on the O ring Sand fibers hair or other foreign matter on the O ring groove or the O ring contact surface Catching of the strap the bag of silica gel etc at the time of sealing the Case E 35 7 Throwing the Case from a boat into the water jumping with the Case into the water or other sudden application of strong forces onto the Case When entering the water hand the Case over quietly or avoid impacts in other ways Q9 What are the important points for O ring maintenance AQ Please observe the following items
35. uch dust or with severe temperature changes e Locations with volatile substances This product is made of polycarbonate resin with excellent impact resistance but it may be damaged by scraping against rocks etc It also may break when it hits hard objects or is dropped This product is not a case to soften impacts to the camera inside the product When this product with a digital camera inside it is subjected to impacts or heavy objects are placed onto it the digital camera may become damaged Please handle the product with sufficient care When the product is not used for a long time the waterproof performance may drop because of deterioration of the O ring etc Before use always perform the advance test and the final check Do not apply excessive force to the tripod mount or the accessory mount When a flash is used while the Case is being used shadows may appear at the edges of the picture This is especially notable when taking pictures in macro mode on the wide angle side Please use a flash after image confirmation E 5 Do not use the following chemicals for cleaning corrosion prevention prevention of fogging repair or other purposes When these are used for the Case directly or indirectly with the chemicals in vaporized state they may cause cracking under high pressure or other problems Chemicals which cannot be used Explanation Do not clean the Case with alcohol gasoline Volatile organic solvents
Download Pdf Manuals
Related Search