Oce North America TCS400 User's Manual
Contents
1. 15 16 Oc TCS400 Self support guide Oc TCS400 Self support guide Chapter 2 Safety information GB Instructions for safe use Introduction Oc designed products are tested in accordance with the strictest international safety standards It is important that you observe the safety rules included in this appendix to help assure safe working with the Oc TCS400 Maintenance Do not remove any screws from fixed panels Do not do any maintenance activities other than the maintenance activities for the parts and the maintenance materials described in this manual Do not place any liquids on the machine Use maintenance materials and other materials for their original purpose only Keep maintenance materials away from children Do not mix cleaning fluids or other substances To avoid the risk of introducing hazards all modifications to Oc equipment are strictly reserved to properly qualified and trained service technicians 18 Oc TCS400 Self support guide Connection Attention Do not move the machine yourself but contact your Customer Service It is recommended to connect only those products which meet the inter na tional product safety and radio frequency interference standards and to use an attachment cable as specified by Oc Surroundings If for some reason you have to move the machine yourself please make sure that the mains power point has the right fuse capacity See the Oc T2. and the print quality requirement are balanced Set the Print quality mode to Release Use this mode for example to approve bid sets or for internal releases of drawings The quality is the most important requirement Set the Print quality mode to Presentation Use this mode for example to present drawings to the customers Define the correct content mode 2 Define the correct print quality mode When Then 10 The job contains filled areas in vivid colours and quality is an important requirement Set the Content mode to Area fills The job does not contain filled areas in vivid colours Set the Content mode to Lines text 3 Define the correct content mode Oc TCS400 Self support guide Use the print modes to correct typical inkjet artefacts When Then Ink saturation causes the media to cockle Set the Content mode to Area fills The print contains regular horizontal light or dark bands Set the Print quality mode to Presentation Set the Content mode to Area fills The filled areas contain white stripes Set the Print quality mode to Presentation Set the Content mode to Area fills The coloured lines are not well aligned or blurred Set the Print quality mode to Presentation Set the Content mode to Lines text
3. send you a copy of the missing sheets You can find the address of the Oc organisation in your country in appendix C of the user manual Safety information GB 21 Product safety data sheet Oc TCS400 printer PRODUCT SAFETY DATA SHEET Dc UK Ltd Number E 756 a UK Date September 2004 Model Oc TCS400 Description Max process speed console model wide format inkjet printer 1 0 Ad min Width Depth Height Dimensions Weight 1960 mm 743 mm 1461 mm 180 Voltage Frequency Current rated Building fuse Power consumption stand by Power consumption operation EPA eneray Stan Power consumption sieep mode Mains connection Safety class Protection class 230 50 60 2 0 16 10 1 160 lt 39 W exclusive of the controller 46 W Cable with plug I IEC 536 Protective earth connection IP 20 IEC 529 Sound pressure level at bystander position Sound power level Radio interference Radiation Heat emission Ozone emission Standby 28 dB A In operation main body 50 dB A 44 dB A main body 65 dB A Complies with Directive 89 336 EEC not applicable Standby 110 W at continuous operation 160 W not applicable Room volume Room ventilation Recommendation min 15 m Recommendation min 7 5 m3 h natural ventilation Consumables Oc TCS400 Inks Oc Material Safety Data Sheet E 235 Additional safety information CE Compliance
4. Approved according to Low Voltage Directive 73 23 EEC CE Cony None EPA Eneray Stan ort Approved according to EMC Directive 89 336 EEC c opyright 2002 Oc Technologies B V Venlo NL The content of this safety data sheet is subject to the disclaimer of liability on page see Disclaimer of this manual Material safety data sheet Oc inksOc TCS400 This safety data sheet was not available at the time this manual was published 22 Oc TCS400 Self support guide Product safety data sheet Oc TCS400 scanner PRODUCT SAFETY DATA SHEET oc Oc UK Limited Number E 760 a UK Date June 2003 Model Oc TCS400 Scanner Description Wide format colour scanner Scan width 40 Scan speed 0 5 m min Dimensions Width 1340 mm Depth 490 mm Height 1070 mm Weight 102 kg Voltage 100 240 V Frequency 50 60 Hz Current rated 1 1 0 45 A Power consumption plug in 58 W incl user interface Power consumption stand by 104 W incl user interface Power consumption operation 119 W incl user interface Mains connection Cable with plug Safety class I IEC 536 Protective earth connection Protection class IP XO IEC 529 Standby In operation Sound pressure level 26 dB A main body 51 dB A at operator position impulse Li 8 dB A Sound power level 37 dB A main body 61 dB A Radio interference Complies with Directive 89 336 EEC and FCC rules and regulations par
5. CS400 safety data sheet in this appendix for information about maximum current Do not bridge any mechanical or electrical circuit breakers Do not use an extension lead to connect the machine This machine is not designed for connection to an IT power system An IT power system is a voltage network in which the neutral wire is not connected to earth When the machine is connected through a wall socket place the machine near a wall socket that is easily accessible When the machine is connected through a fixed connection to the electricity grid the disconnect device in the fixed connection must be easily accessible Make sure that the machine is placed on a level horizontal surface of sufficient strength See the Oc TCS400 safety data sheet in this appendix for information about the weight of the equipment Make sure there is sufficient space around the machine This facilitates reloading materials as well as maintenance Do not place the machine in rooms which are subject to excessive vibration Do not place the machine in rooms which are too small or insufficiently ventilated See the Oc TCS400 safety data sheet in this appendix for information about space and ventilation requirements Safety information GB 19 General 20 Always use materials recommended by Oc and developed for the Oc TCS400 Materials not approved by Oc can cause faults in your machine Do not use the machine when it is emitting unusual sounds R
6. Oc TCS400 Self support guide Oc Technologies B V Trademarks Products in this manual are referred to by their trade names In most if not all cases these designations are claimed as trademarks or registered trademarks of their respective companies Safety information This manual contains the following safety information Instructions for safe use You are advised to read this information before you start to actually use the system Technical safety information such as safety data sheets can also be found in this chapter Where applicable attentions are used throughout this guide to point out safety precautions to be taken a Copyright 2003 Oc Technologies B V Venlo The Netherlands All rights reserved No part of this work may be reproduced copied adapted or transmitted in any form or by any means without written permission from Oc Oc Technologies B V makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose Further Oc Technologies B V reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation to notify any person of such revision or changes Code number 1060012280 Edition 2003 03 Contents Chapter 1 Self support tips GB What to do when a problem occurs 6 Correct a problem 6 What to
7. The colour of one area or line runs into the colour of another area or line Set the Print quality mode to Presentation Parts of lines are missing or lines are stepped Set the Content mode to Lines text Parts of characters are missing Set the Content mode to Lines text On high gloss photo paper the individual ink drops merge on the media Set the Print quality mode to Release or to Presentation The length and width measurements are different from the original Set the Print quality mode to Presentation 4 Use the print modes to correct typical inkjet artefacts Self support tips GB 11 Use the wizards to achieve optimal output quality When to do Before you start the Optimise print quality wizard first check the following Did you define the correct media type for your job Define the correct media for optimal output quality Did you define the correct print mode settings for your job see Define the correct job settings for optimal output quality on page 9 After you checked that you used the correct media and the correct print modes use the Optimise print quality wizard to solve the following problems on your printed output Regular horizontal light or dark bands on the output White stripes in filled areas The length and width measurements are different from the original The coloured lines are not well ali
8. do when you are not satisfied with the output quality 7 Achieve optimal output quality 7 Define the correct job settings for optimal output quality 9 Use the wizards to achieve optimal output quality 12 What to do when the system indicates a defective printhead 14 Use the Replace printhead wizard to change a defective printhead 14 What to do when you have problems with the sending of print jobs 15 Important points for the sending of print jobs 15 Chapter 2 Safety information GB Instructions for safe use 18 Safety data sheets 21 EPA Energy Star 24 Contents Oc TCS400 Self support guide Oc TCS400 Self support guide Chapter 1 Self support tips GB What to do when a problem occurs Correct a problem When a problem occurs on your system do the following 1 Use the wizards Use the on line off line key key 4 on the folded cover on the printer operator panel to go off line to the wizard selection screen 2 Use the user manual on the documentation CD ROM for detailed descriptions about how to correct problems Use the wizards to correct problems Use the wizards to do one of the following 1 Use the Feed amp cut wizard to cut the output or to clean cut a roll of media Chapter 6 of the user manual includes complete information about how to use this wizard 2 Use the Change media type wizard to change the media type defined on the system Define the correct media for optimal output quality 3 Us
9. e the Optimise print quality wizard as a final option to correct the problems with the print quality see Use the wizards to achieve optimal output quality on page 12 4 Use the Replace printhead wizard to replace a defective printhead see Use the Replace printhead wizard to change a defective printhead on page 14 5 Use the Replace cassette wizard to replace the maintenance cassette Chapter 8 of the user manual includes complete information about this wizard 6 Use the Configure system wizard to check the network settings When you do not have a keyboard mouse and monitor with your controller you can also use the Configure system wizard to clear the set memory Chapter 3 of the user manual includes complete information about this wizard Use the user manual on the documentation CD ROM to correct problems When the information in this guide does not completely support you while you use the Oc TCS400 refer to the user manual on the user documentation CD ROM for more information 6 Oc TCS400 Self support guide What to do when you are not satisfied with the output quality Achieve optimal output quality Introduction The Oc TCS400 offers 2 methods to check the print quality Make a quality check print Make a demo print On the system information card on the on line screen of the printer use the lower softkey for Demo prints key 6 on the folded cover to enter the menu with t
10. emove the plug from the power socket or turn off the fixed connection to the electricity grid and contact Customer Service Note This is a class product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Oc TCS400 Self support guide Safety data sheets Introduction Disclaimer The disclaimer below applies to all safety data sheets in this manual Contact your local Oc organisation for questions about Oc products regarding health safety and environment You can find the address of your local Oc organisation in appendix C of this manual The safety data sheets in this manual have been compiled to the best of our knowledge They are intended as a compact guide to the safe handling of this product We reserve the right to revise safety data sheets as new information becomes available It is the user s responsibility to determine the suitability of this information for the adoption of safety precautions as may be necessary It is the user s responsibility to contact Oc to make sure that the safety data sheets are the latest ones issued If and in so far as limitation of liability is permitted under the applicable laws we do not accept liability for any inaccuracy that may occur in this information Note Not all safety data sheets were available at the moment this manual was published The Oc organisation in your country will be pleased to
11. gned or blurred Missing sections in lines or stepped lines Parts of characters are missing Drop out caused by nozzle problems Chapter 7 of the user manual includes complete information about how to optimise the print quality Before you begin During the Optimise print quality wizard the system does a calibration The calibration is only possible on one of the following media types indicated below Before you start the wizard first load and define one of these media types on the printer Standard paper Premium coated paper Bond Coated bond Matt photo paper High gloss photo paper Deluxe bond 12 Oc TCS400 Self support guide How to start the Optimise print quality wizard 1 Press the on line off line key key 4 on the folded cover to set the printer off line Press the lower softkey for Optimise print quality key 6 on the folded cover to enter the wizard Follow the steps of the wizard When there are no defective printheads you can do a printhead alignment When you select No the system returns to the off line menu When there are printheads with defective nozzles you can not do a printhead alignment When there are printheads with defective nozzles you can do the following Continue the printing without the enabling of the fallback mode The output quality is not optimal Enable the fallback mode to continue the printing with optimal output quality Enter the Replace printhead w
12. he quality check print and the demo print Chapter 7 of the user manual includes a section about how to check the print quality When you are not satisfied with the output quality use the following procedure 1 First make sure that you load and define the correct media type on the printer Use the Change media type wizard to load a media roll and to change the media type defined on the system Then make sure you define the correct media type for your job The following problems are never connected to media Ignore the above steps for these problems and directly continue with step 3 see Important points for the sending of print jobs on page 15 The length and width measurements are different from the original The coloured lines are not well aligned Missing sections in lines or stepped lines Missing parts of characters Drop out caused by nozzle problems 2 Make sure you defined the correct print mode for your job see Define the correct job settings for optimal output quality on page 9 Self support tips GB 7 3 Finally when you have defined the correct media and the correct print mode and you are still not satisfied with the output quality use the wizards to achieve optimal output quality see Use the wizards to achieve optimal output quality on page 12 Chapter 7 of the user manual includes a table with recommended media types and print modes for the different types of jobs Chapter 7 of the
13. izard to replace the defective printhead Self support tips GB 13 What to do when the system indicates a defective printhead Use the Replace printhead wizard to change a defective printhead When to do The system indicates the defective printhead Only replace the printhead indicated by the system Chapter 8 of the user manual includes complete information about how to replace a defective printhead Before you begin During the Replace printhead wizard the system does a calibration The calibration is only possible on of the following media types Standard paper Premium coated paper Bond Coated bond Matt photo paper High gloss photo paper Deluxe bond How to start the Replace printhead wizard 14 Attention Only open the top cover when the wizard prompts you Press the on line off line key key 4 on the folded cover to set the printer off line Press the lower softkey for Replace printhead key 6 on the folded cover to enter the wizard Follow the steps of the wizard At the end of the wizard the printer calibrates When the calibration is completed the screen displays the calibration status Oc TCS400 Self support guide What to do when you have problems with the sending of print Jobs Important points for the sending of print jobs Before you send print jobs to the Oc TCS400 remember the following The values defined in the Oc Settings Editor are default values fo
14. r the system You can define a number of job settings in the printer drivers or the job submission tools The settings defined in the printer drivers or the job submission tools always overrule the settings defined in the Oc Settings Editor Chapter 10 of the user manual and the on line help in the Oc Settings Editor include complete information about the Oc Settings Editor m Make sure that the media type and size defined in your job match the media type and size defined on the printer Make sure that you define the correct print mode for your job Make sure that you define the correct media type for your job Make sure that you define the correct job settings For example orientation rotate shift and Automatic roll switch The section about the correct media types for your jobs describes the job settings you can use with the different media types and sizes A job submission tool like Oc Print Exec Workgroup provides you with information about the media defined on the system The printer drivers do not give this type of information When you use the printer drivers to send your jobs use Oc Remote Logic to view information about the media defined on the printer in the Oc System Control Panel Chapter 4 of the user manual includes more information about how to send print jobs to the Oc TCS400 Chapter 6 includes more information about how to define the correct media settings for your jobs Self support tips GB
15. se data Attention Jf this printer is upgraded to a multifunctional device by adding a wide format colour scanner the system does not comply with the ENERGY STAR sleep mode specification for a wide format multifunction device The ENERGY STAR logo which appears in the printer operator panel only refers to the printer The EPA ENERGY STARS Criteria for printers involves the following feature Sleep mode The power use of some functions is automatically decreased to save energy The printer enters the sleep mode 30 minutes after the last print job is completed The key operator can adjust this default time within a range between 30 and 240 minutes It is suggested to determine the appropriate default time for your work pattern by changing the setting in steps of 30 minutes and testing each setting for at least a week Only if this limit of 240 minutes still causes sizable inconvenience due to your usage pattern the key operator can disable the sleep mode Oc TCS400 Self support guide anr H lt ENERGY STAR is a U S registered mark Safety information GB 25 26 Oc TCS400 Self support guide Index J job submission 15 M media settings o off line mode output quality P print modes 9 S system screen U user manual W wizards 6 6 6 Index 27 28 Oc TCS400 Self support guide
16. t 15 Class A Radiation Below the Threshold Limit Values for UV Visible and IR radiation TLV list of ACGIH Heat emission Standby 104 W in operation 119 W Ozone emission Not applicable Room volume Recommendation min 15 m3 Room ventilation Recommendation min 7 5 m3 h natural ventilation Use simulation at random Not applicable operation Consumables Not applicable Additional safety information None CE Compliance Listed according to standard UL 1950 and CAN CSA C22 29 No 950 Copyright 2003 Oc Technologies B V Venlo NL The content of this safety data sheet is subject to the disclaimer of liability on page see Disclaimer of this manual Safety information GB 23 EPA ENERGY STAR Introduction Features 24 Oc Technologies B V has joined the ENERGY STAR Program of the United States Environmental Protection Agency EPA The purpose of the ENERGY STAR Program is to promote the manufacturing and marketing of energy efficient equipment thereby potentially reducing combustion related pollution Using the energy management features outlined below prevents unnecessary power consumption which helps to prevent air pollution from electricity generating plants and saves money on your utility bills As an ENERGY STAR Partner Oc Technologies B V has determined that this printer model meets the ENERGY STAR guidelines for energy efficiency See the Product Safety Data Sheet in this appendix for power u
17. user manual includes a table with a complete overview of the settings and the methods to correct specific problems with the output quality Oc TCS400 Self support guide Define the correct job settings for optimal output quality Definition To get optimal output quality define the correct print modes Use the following order to define the print modes Define the correct media settings The website http supplies oce com includes information about the correct media settings for your jobs Define the correct Colour mode Define the correct Print quality mode Define the correct Content mode Chapter 7 of the user manual includes information about the recommended job settings for your jobs Define the correct colour mode When Then The original is in colour and the printed output requirement is colour set the Colour mode to Colour The original is in colour and the printed output requirement is greyscale set the Colour mode to Greyscale The original is greyscale set the Colour mode to Greyscale 1 Define the correct colour mode Self support tips GB Define the correct print quality mode When Then Example Speed is the most important requirement Set the Print quality mode to Check Use this mode for example to check if all the information is visible on the printed output The speed requirement
Download Pdf Manuals
Related Search