Nikon VT650 User's Manual
Contents
1. Each time this button is pressed the current picture adjustment item will change as follows Ce Brightness Contrast Color Hue Sharpness 2 Unavailable items will be skipped 15 Aspect Button Press this button to display the Aspect Ratio select window Each time this button is pressed the current aspect ratio will change as follows C Normal gt Zoom gt Wide Zoom e Cinema You can also select the aspect ratio by using the Select lt q or gt button If no adustments are performed within 3 seconds the As pect Ratio select window will disappear See also page E 32 16 Help Button Provides information about the current signai and the status of the projector 17 Freeze Button This button will freeze a picture Press again to resume motion 18 Picture Mute Button This button turns off the image and sound for a short period of time Press again to restore the image and sound 19 Magnify Button Use this button to adjust the image size up to 400 20 Volume Button Press to increase the volume and to decrease it NOTE The default is the Computer mode which allows you to use the Select Cancel and Enter buttons as your computer mouse When the POWER ON OFF MENU HELP or MAGNIFY button is pressed the PJ button lights red to indicate that you are in the Pro jector mode If no buttons are pressed within 10 seconds the light goes out and the Projector mode is cancel2. Problem Check These Items Does not turn on Check that the power cable is plugged in and that the power button on the projector cabinet or the remote control is on Ensure that the lamp cover is installed correctly See page E 38 Check to see if the projector has overheated or the lamp usage exceeds 2100 hours 3100 hours in Eco mode If there is insufficient ventilation around the projector or if the room where you re presenting is particularly warm move the projector to a cooler location No picture Use the menu to select your source Video S Video or RGB See page E 31 Ensure your cables are connected properly Use menus to adjust the brightness and contrast See page E 31 Remove the lens cap Reset the settings or adjustments to factory preset levels using the Factory Default on the Image Options Menu See page E 33 Image isn t square to the screen Reposition the projector to improve its angle to the screen See page E 28 Use the Keystone on the Image Options Menu to correct the trapezoid distortion See page E 31 Picture is blurred Adjust the focus See page E 27 Reposition the projector to improve its angle to the screen See page E 28 Ensure that the distance between the projector and screen is within the adjustment range of the lens See page E 17 Image is scrolling vertically horizontally or both Use menus or Source button on the remote control or the cabinet to select the sourc
3. up to 0 6 4mm e If the projected image does not appear square to the screen then use keystone correction for proper adjustment Printed in China TN8P1131 Remote Control Features ee rr aT vera ben 4 OO 3 a T 6 7 PIOTURE ASPECT 14 15 TEP FEE PONE 16 18 49 wer 17 pam F 20 NEC NOTE Ifyou are using a Macintosh computer you can click either the right click or left click button to activate the mouse 7 Infrared Transmitter Direct the remote control toward the remote sensor on the projector cabinet 2 LED Flashes when any button is pressed 3 Power ON Button If the main power is applied you can use this button to turn your projector on 4 Power OFF Button If the main power is applied you can use this button to turn your projector off NOTE To turn off the projector press and hold the POWER OFF button for a minimum of two seconds 5 VIDEO Button Press this button to select a video source from a VCR DVD player laser disc player or document camera 6 S VIDEO Button Press this button to select an S Video source from a VCR 7 RGB Button Press this button to select an RGB source from computer or com ponent equipment connected to your RGB port 8 Auto Adjust Button Use this button to adjust Position H V and Pixel Clock Phase for an optimal picture Some signals may not be displayed correctly or in some cases i
4. NEC VT650 Quick Connect Guide Connections Step 1 Connect the supplied 15pin 15pin signal cable For older Macintosh computers use a commercially available pin adapter to connect to your Macintosh s video port Connecting the remote mouse receiver to your computer To USB port of PC or Macintosh To Mouse PS 2 port of PC Attach the supplied PS 2 Adapter You can use the supplied wireless remote control and remote mouse receiver to operate your PC mouse wirelessly from across the room See page E 14 Power down all equipment before making connections Remote sensor on the remote mouse receiver Monitor Step 2 Connect the supplied power cable Step 3 Turn on the projector NOTE To turn off the projector press and hold the POWER button for a minimum of two seconds Power button Step 4 Set up the Projector To adjust the projector s focus or to zoom in and out use the Focus ring or Zoom lever on the lens To optimize image press the AUTO ADJUST button on the cabinet or the remote control Adjusting the T ilt Foot Press and hold the T ilt button on the front of the projector Lift the front edge of the projector to the desired height and release the button to lock the Adjust able T ilt Foot e To fine tune the image s position vertically on the screen rotate the foot Each of the rear feet height can be changed
5. e you want to input Remote control does not work Install new batteries See page E 13 Make sure there are no obstacles between you and the projector Stand within 22 feet 7 m of the projector See page E 13 Make sure that you are in the Projector mode or the PJ button lights in red If not press the PJ button Status indicator is lit or blinking See the Power Status Light messages Cross color in RGB mode If Auto Adjust is off turn it on If Auto Adjust is on turn it off and balance the image with the Position and Clock Adjust on the Advanced Options Menu See page E 33
6. ed Source Select Picture Volume Image Options Projector Options Information Source Select RGB Video S Video Picture Brghtness Contrast Color Hue Sharpness Volume Image Options Keystone Lamp Mode Normal Eco Factory Default All Data Current Signal Projector Options Menu L Menu Menu Mode Basic Advanced Language Setup i English German French Source Display Italian Spanish Swedish No Input Display Japanese Volume Bar Keystone Bar On Off Filter Clean Message ff Menu Display Time One On Off On Off On Off Manual Auto 5 sec Auto 15 sec Auto 45 sec This setting is optional you need the optional presentation remote control PR51KIT Setup Orientation Desktop Front Ceiling Rear Cinema Position Desktop Rear Ceiling Front Background Top Center Bottom Blue Black Logo Information Page 1 Source Index Input Terminal Horizontal Frequency Vertical Frequency Sync Polarity Page 2 Signal Type Video Type Sync Type Interlace Page 3 Remaining Lamp Time Lamp Hour Meter Projector Usage Troubleshooting Power Status Light Messages Condition Power Indicator Status Indicator Standby Steady orange Cooling down Blinking gree
7. n Blinks green for 60 seconds Lamp in Nomal mode Steady green Lamp in Eco mode Steady green Steady green One minute after lamp is turned on Blinking green Depending Lamp mode Do not turn off the projector during this condition Retrying to turn on lamp Steady green Blinking orange The projector retries 3 times at an interval of 15 sec for max 45 sec Lamp has reached its end of life 2000 hours or over Normal mode 3000 hours or over Eco mode Steady green Steady red Message appears on screen during this condition The projector reaches its end of life Please replace the lamp as soon as possible Lamp life has reached its end of life 2100 hours or over Normal mode 3100 hours or over Eco mode Steady orange Steady red The projector is in standby mode and cannot be turned on Lamp or filter cover error 3 locations Steady orange Blinking red 1 sec interval The projector is in standby mode and cannot be turned on Temperature error Steady orange Blinking red 4 sec interval The projector is in standby mode and cannot be turned on Fan error Steady orange Blinking red 8 sec interval The projector is in standby mode and cannot be turned on Lamp error Steady orange Blinking red 12 sec interval The projector is in standby mode and cannot be turned on Common Problems amp Solutions
8. t may take some time for a source to switch between sources 9 Menu Button Displays the menu 10 Select A V lt P mouse Buttons When you are in the Computer mode these buttons work as a computer mouse When you are in the Projector mode which is indicated by lighting the PJ button AV Use these buttons to select the menu of the item you wish to adjust lt P Use these buttons to change the level of a selected menu item 11 Enter Left click Button When you are in the Computer mode this button works as the mouse left button When you are in the Projector mode which is indicated by light ing the PJ button Use this button to enter your menu selection It works the same way as the Enter button on the cabinet 12 Cancel Right click Button When you are in the Computer mode this button works as the mouse right button When you are in the Projector mode which is indicated by light ing the PJ button Press this button to exit Menus It works the same way as the Cancel button on the cabinet 13 PJ Button Press this button to switch the Select Cancel and Enter buttons between the Projector mode lit red and the Computer mode Press this button or any one of the Power ON OFF Menu Help and Mag nify buttons to switch to the Projector mode and the PJ button lights red To switch back to the Computer mode press the PJ button again 14 Picture Button Press this button to display the Picture adjustment window
Download Pdf Manuals
Related Search