Network Technologies MAN049 User's Manual
Contents
1. a computer 3 SCAN SCAN Mode is indicated by a flashing CPU port LED The switch scans to either port with a CPU powered ON That port remains active for the configured dwell time default time is 5 seconds before switching to the other powered ON CPU port See Keyboard Control Section for configuring the scan dwell time NOTE The keyboard and mouse must remain idle for the full SCAN dwell time before the switch selects the other port BROADCAST use with extreme caution BROADCAST Mode is indicated when both CPU LED s are illuminated This mode allows the operator to send keystrokes to both active computers simultaneously However BROADCAST Mode has some critical requirements 1 BROADCAST Mode must be off when booting and attached computer 2 COMMAND Mode must be OFF for keystrokes to reach attached computer when in BROADCAST KEYBOARD FEATURES The keyboard configuration of each computer is saved in the NTI Switch For example if the computer attached to Port 2 had CAPS LOCK and NUM LOCK selected the last time that computer was accessed then they will automatically be set when that computer is accessed again KEEMUX P2 REMOTE SPECIFICATON RMT 2 ST SIGNAL DESCRIPTION it LED1 TTL output low port 1 selected LED2 TTL output low port 2 selected 3 3 swr TTL of contact closure input 10K pullup Ground 5V for LED s limited to 20ma Low lt 4 volts High gt 2 4 volts Control When pin 3 SWT is2. brought low for a minimum of 10 MS and then returned high the switch will select the other port toggle TROUBLESHOOTING 1 Verify all cables are securely connected and that installation procedure was carefully followed 2 Verify that power up sequence was observed 3 Ifa computer seems to be locked up press the CPU SELECT button a couple of times 4 If the problem still persists unplug the keyboard and mouse cables not the CPU keyboard and mouse from KEEMUX P2 and reconnect them 5 Ifa Compaq Proliant 2000 or non Intel architecture Unix machine with PS 2 ports such as HP 9000 does not detect a keyboard or mouse attached when booting booster cables VKINT 1K 1 may be needed for both the keyboard and mouse CPU ports See note under INSTALLATION on page 3 for proper installation instruction WARRANTY INFORMATION The warranty period on this product parts and labor is one 1 year from the date of purchase Please contact Network Technologies Inc at 800 742 8324 800 RGB TECH or 330 562 7070 or visit our website at http www nti1 com for information regarding repairs and or returns A return authorization number is required for all repairs returns COPYRIGHT Copyright 2001 by Network Technologies Inc All rights reserved No part of this publication may be reproduced stored ina retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the pri
3. NETWORK 1275 Danner Dr Tel 330 562 7070 AN0 aala Aurora OH 44202 Fax 330 562 1999 KEEMUX P2 2 Port PS 2 KVM Switch INSTALLATION USER GUIDE o Li o Dono oaan doo o fe ma ADBODDU naau AA Gan panOD na papa Hana Se AS Dones col qua A NETWORK TECHNOLOGIES INCORPORATED Cim Ps2 Em KEEMUX P2 PS 2 anA CPU PA w TABLE OF CONTENTS Intro dut OMA hn eis A Gi NE BEA Materials Materials Supplied dereie rnea baal edan aan Materials NOT supplied but required Woo Installation secede ee A A aa anna Using the NTI Switch Front Panel Controlar id ha Bir ANAN SANA adt Keyboard Control id den Aka Aa aa Ja balad Pan ana Ta mana ena LNG SCAN MODE Ha cre tunas ANAN angan anna EN NE anna BROADCAST MODE sita NAAALAALA ATA KEP na a AN Keyboard Features iii ago c aNG Bka dives uin KEEMUX P2 Remote Specifications a TROU Dle SHOOLIN Ges ALAN al saia a ad ae Warranty ntorMmatio Moi nd o ALL INTRODUCTION The KEEMUX P2 switch allows one user to access two PS 2 computers with only one keyboard monitor and mouse Internal auto boot circuitry allows both computers to boot simultaneously and error free without the need for a keyboard monitor and mouse on each computer MATERIALS Materials Supplied with this kit 1 NTI PS 2 KVM Switch Materials Not Supplied BUT REQUIRED 1 A set of 2 cables for each computer being connected to the switch mus
4. or written consent of Network Technologies Inc 1275 Danner Drive Aurora OH 44202 CHANGES The material in this guide is for information only and is subject to change without notice Network Technologies Inc reserves the right to make changes in the product design without reservation and without notification to its users SERIAL NO DATE INSPECTED BY Ol KEEMUX P2
5. t be used PS 2 computer to switch 1 VEXT xx MM high res or VINT xx MM low res for video interface 2 1 VVKINT xx MM for keyboard and mouse interface OR 2 VKINT xx MM for keyboard or mouse interface Materials Not Supplied BUT MAY BE REQUIRED VKINT 1K 1 Booster Cable for keyboard or mouse interface with Compaq Proliant 2000 and non Intel architecture Unix machines with PS 2 ports such as HP 9000 Two VKINT 1K 1 cables are needed for each applicable computer INSTALLATION 1 Turn OFF power to all computers that will be connected to the NTI Switch before connecting or disconnecting any cables WARNING You MAY DAMAGE YOUR COMPUTER IF YOU DO NOT TURN THE POWER OFF BEFORE CONNECTING OR DISCONNECTING CABLES 2 Connect PS 2 keyboard to USER KEYBD port on rear panel of switch Connect PS 2 Mouse to USER MOUSE port on rear of switch Connect monitor to MONITOR port on rear of switch Using 1 VVKINT xx MM or 2 VKINT xx MM or VKEXT xx MM cables required not supplied connect keyboard and mouse ports of PS 2 computer to CPU 1 KEYBD and CPU 1 MOUSE ports on rear of switch NOTE If installing a Compaq Proliant 2000 or a non Intel architecture Unix machine with PS 2 ports such as HP 9000 booster cables may be needed VKINT 1K 1 If booster cables are used they must first be directly connected to both the keyboard and mouse CPU ports on the switch 6 Using VINT xx MM or VEXT xx MM required no
6. t supplied connect video port of PS 2 computer to CPU 1 VIDEO port on rear of switch 7 Repeat steps 5 amp 6 for CPU 2 Oh Ba O POWER UP SEQUENCE POWER DOWN SEQUENCE 1 The KEEMUX P2 is powered by the computers it is connected to 1 Power down computers 2 Turn on power to monitor 3 Turn on power to either or both computer s USING THE NTI SWITCH The switch can be operated by the front control panel or by keyboard control Front Panel Control 1 Pressing the touch switch on the front panel will toggle between CPU 1 and CPU 2 and connect the selected computer to the keyboard monitor and mouse 2 Holding down the CPU SELECT button for more than 2 seconds will cause the switch to cycle through 3 extended modes of operation SCAN BROADCAST and COMMAND see Keyboard Control Scan and Broadcast sections Release the button when the desired mode has been selected Keyboard Control To control switch from keyboard COMMAND Mode must be enabled To enable COMMAND Mode CTRL accent key To disable COMMAND Mode ESC or CTRL gt To increment port Mor 3 To decrement port D or To select a specific port P01 or P02 To enable disable BROADCAST Mode B To enable disable SCAN Mode Ss To set the scan dwell time time in seconds before switching to other port Txxx xxx from 002 to 255 NOTE You must exit COMMAND Mode in order to type to
Download Pdf Manuals
Related Search