Netgear WND930 Installation Guide
Contents
1. 4 Check the LEDs to verify that the access point is set up correctly LED Power LED Off Power is off Solid green Power is on Amber then blinking green A self test is running or software is being loaded During startup the LED is first steady amber then goes off and then blinks green before turning steady green after about 45 seconds If after one minute the LED remains amber or continues to blink green it indicates a system fault Activity LED Off There is no network traffic through the access point Blinking green There is network traffic through the access point 2 4G WLAN Off The wireless interface is off LED Solid green The wireless interface is on Blinking green Wireless activity is detected on the 2 4G band 5G WLAN LED Off The wireless interface is off Solid green The wireless interface is on Blinking green Wireless activity is detected on the 5G band Heater LED Off Heater is off Solid green Heater is on LAN port LEDs Off No link is detected Solid green Link is detected Solid amber 10 100 1000 speed connection is detected Blinking amber 10 100 1000 speed activity is detected To configure your access point for your network Connect to the access point by opening your browser and entering the access point s IP address If a DHCP server is not installed in your network the default IP address is 192 168 0 100 A login window displays2. Enter admin for the user name and password for the password both in lower case letters The access point user interface displays Select Configuration gt System gt Basic gt General from the menu Complete the Access Point Name feld and select your Country Region of operation from the drop down list Select Configuration gt IP gt IP Settings from the menu and configure the IP settings for your network Note If you use DHCP reserve an IP address based on the access point s MAC address on the DHCP server You can then use that address to log in to the access point Select Configuration gt Wireless gt Basic gt Wireless Settings and configure the wireless settings for your network For more information about wireless settings see the reference manual Select Configuration gt Security gt Profile Settings and configure security profiles for your network For more information about security profile settings see the reference manual Deploy the Access Point The best location for your access point is elevated such as wall or ceiling mounted at the center of your wireless coverage area and within line of sight of all mobile devices gt 1 PA 201 18134 04 To deploy your access point Disconnect your access point and position it where you will deploy it Connect an ethernet cable from your access point to a LAN port on your router switch or hub Connect a power sourcing equipment PSE
3. to one of the PoE ports on the access point If your router switch or hub supplies PoE skip this step Note You must supply either AT power to at least one LAN port or AF power to two LAN ports to power the access point You must supply AT power to both LAN ports to receive PoE power out Using a wireless device verify connectivity by using a browser to connect to the Internet NETGEAR Inc 350 East Plumeria Drive San Jose CA 95134 USA August 2014 Optional External Antennas The WND930 supports optional external antennas gt To install optional external 2G or 5G antennas 1 Attach the 2G or 5G antennas to the corresponding connectors on the side panels of the access point 2 Log into the access point and configure it to use the external antennas Troubleshooting Tips This section provides some tips for correcting simple problems that you might encounter For more troubleshooting information see the troubleshooting chapter in the reference manual Possible Solution No LEDs are The access lit on the point has no access point power e Make sure that a power source equipment PSE is connected via Ethernet to at least one PoE port Make sure that the power source equipment PSE is powered on The LAN LED A hardware is off connection problem exists Make sure that the cable connectors are securely plugged into the access point and to the network switch Make sure that the
4. Installation NETGEAR Outdoor High Power Wireless N Access Point WND930 Package Contents Unpack the box and verify the contents Outdoor High Power Wireless N Access Point Wall mounting bracket Four bracket screws Two grounding screws Two pole mount clamps Three weatherproof cable glands NETGEAR Set Up the Access Point Before mounting the access point in a high location first set up and test the unit to verify wireless network connectivity Note The access point has a DHCP client enabled by default If a DHCP server exists in your network the access point obtains an IP address from the DHCP server If a DHCP server is not detected in your network after 30 seconds the access point sets its IP address to a static IP address of 192 168 0 100 gt Tocable your access point 1 Using an Ethernet cable connect a power sourcing equipment PSE to a PoE port on the access point Note You must supply either AT power to at least one LAN port or AF power to two LAN ports to power the access point You must supply AT power to both LAN ports to receive PoE power out 5G LAN3 PoE out P o LAN1 Activity o Penter 2 4G Reset 2 Ifa DHCP server is not connected to your network configure a computer with a static IP address of 192 168 0 210 and a subnet mask of 255 255 255 0 3 Connect an Ethernet cable from a LAN port on the access point to a LAN port on the PC
5. cess point see the reference manual Support Thank you for selecting NETGEAR products After installing your device locate the serial number on the label of your product and use it to register your product at https my netgear com You must register your product before you can use NETGEAR telephone support NETGEAR recommends registering your product through the NETGEAR website For product updates and web support visit http support netgear com NETGEAR recommends that you use only the official NETGEAR support resources For the current EU Declaration of Conformity visit http support netgear com app answers detail a_id 11621 For regulatory compliance information visit http www netgear com about regulatory See the regulatory compliance document before connecting the power supply NETGEAR the NETGEAR logo and Connect with Innovation are trademarks and or registered trademarks of NETGEAR Inc and or its subsidiaries in the United States and or other countries Information is subject to change without notice NETGEAR Inc All rights reserved
6. network switch is turned on The Wireless The wireless Make sure the powered device is providing sufficient LED is off connection power to the access point does not work Log into the access point and verify that the radio or radios are turned on Contact NETGEAR if the Wireless LED remains off You cannot Multiple Make sure that the access point is correctly installed it configure possible is powered on and that the LAN LED is lit the access causes Make sure that your computer is using an IP address point from a in the same range as the access point The access point ee default IP address is 192 168 0 100 and the default subnet mask is 255 255 255 0 Quit the browser clear the cache delete the cookies and launch the browser again possible Solution You cannot A configuration Make sure that the SSID and wireless security settings access the problem exists Of the wireless device are the same as those of the access point Internet The wireless device might not have the correct TCP IP or the f settings to communicate with the network Restart the LAN rom wireless device and check that TCP IP is set up correctly a wireless for that network device The access point default values might not work with your network Check the access point default configuration against the configuration of other devices in your network For information about changing the default values of the ac
Download Pdf Manuals
Related Search