Netgear EX6100 Installation Guide
Contents
1. Solid green Best connection Power LED eO gt WPS LED Q eu Solid amber Good connection Solid red Poor connection Off No connection Solid amber The extender is booting Solid green The extender is powered on Off The extender is powered off Solid green WiFi security is enabled WPA or WPA2 Blinking green A WPS connection is in progress Off WiFi security is not enabled Note If the Router Arrow or Client Arrow LED blinks see Find the Best Location on page 12 If no arrow LEDs are lit the extender is in a good location Install the WiFi Extender Place the extender apply power and connect it to your WiFi network Place the Extender and Apply Power 1 3 Place your extender in the same room as your WiFi router Note Proximity to the WiFi router is required only during the initial setup process Plug the extender into an electrical outlet The Power LED lights green If the Power LED does not light press the Power button Make sure that the switch on the extender is set to Extender Connect to an Existing WiFi Network To extend the range of your WiFi network you must connect the extender to your existing WiFi network You can do this in one of two ways Connect with WPS For more information see Connect with WPS on page 6 Connect with genie Smart Setup For more information see Connect with NETGEAR genie Smart Setup on page 8 Connect with WPS Wi Fi2. Protected Setup WPS lets you join a secure WiFi network without typing the network name and password The WPS buiton is a physical button on the router or access point WPS does not support WEP network security If you are using WEP security see Connect with NETGEAR genie Smart Setup on page 8 gt Toconnect with WPS 1 Press the WPS button on the side panel of the extender The WPS LED e blinks Within two minutes press the WPS button on your router or access point The WPS LED on the extender lights solid green the Router Link LED Ts lights and the extender is connected to your existing WiFi network Note Ifthe Router Link LED does not light try again If it still does not light see Connect with NETGEAR genie Smart Setup on page 8 If your WiFi router supports the 5 GHz band repeat steps 1 and 2 to connect the extender to the 5 GHz band 4 Find the new extender network name The extender s wireless network name SSID changes to your existing WiFi network name with _2GEXT or _5GEXT at the end of the name depending on whether the extender is connecting to your WiFi network in 2 4 GHz or 5 GHz For example e Existing WiFi network name MyNetworkName e New extended network name MyNetworkName_2GEXT or MyNetworkName_5GEXT 5 Connect your existing WiFi devices to the new extended network Use the same WiFi password that you use for your WiFi router 6 Unplug the extender and move it to a new locatio
3. NETGEAR Wy EX6100 WIFI Range Extender Installation Guide e Getting Started The NETGEAR WiFi Range Extender increases the distance of a WiFi network by boosting the existing WiFi signal and enhancing the overall signal quality over long distances An extender repeats the signals from an existing WiFi router or access point WiFi Range Patania Boosts the range of you existin ra Wia oe nal in Existing WiFi Sometimes your router does not provide the WiFi e coverage you need You can also connect the extender to your router or gateway with an Ethernet cable and use the extender as an 11ac access point See Install the Extender as an Access Point on page 15 Meet Your Extender Before you install your extender familiarize yourself with its LEDs buttons and ports Front Panel and Side Panel Router Link LED C Router Arrow LED Client Arrow LED be Client Link LED Power LED WPS LED ge Access Point Extender switch b 4 sos Power On Off button gt a WPS button y Factory Reset button Ethernet port V LED Descriptions Router Link LED This LED indicates the connection between the extender W and the router or access point Solid green Best connection Solid amber Good connection Solid red Poor connection Off No connection Client Link LED This LED indicates the connection between the extender and a computer or mobile device q
4. ds registering your product through the NETGEAR website For product updates and web support visit http support netgear com NETGEAR recommends that you use only the official NETGEAR support resources You can get the user manual online at http downloadcenter netgear com or through a link in the product s user interface Trademarks NETGEAR the NETGEAR logo and Connect with Innovation are trademarks and or registered trademarks of NETGEAR Inc and or its subsidiaries in the United States and or other countries Information is subject to change without notice NETGEAR Inc All rights reserved Compliance For the current EU Declaration of Conformity visit http support netgear com app answers detail a_id 11621 For regulatory compliance information visit http www netgear com about regulatory NETGEAR Inc 350 East Plumeria Drive San Jose CA 95134 USA 201 17417 03 November 2013
5. ess Network Connection NETGEAR_EXT O Last step once you have reconnected your device running this Wizard please mark the checkbox and click the Continue button to finalize your installation Continue 10 10 11 12 13 Use a WiFi network manager on the computer or mobile device to connect to the extender s newly created WiFi network Use your password to connect Select the check box and click the Continue button You are now one step away from completing the installation Step 1 Select the WiFi Network Your Extender network has been created Extender network 2 4GHz b g n Extender network 5GHz a n ac Step 2 Set Up the Wireless network name SSID ntgrwlan_2GEXT Wireless network name SSID ntgrwlan_5q_5GEXT Extender Security type WPA2 PSK Security type WPA2 PSK Passphrase Passphrase Step 3 Apply Settings Now you need to reconnect your wireless device s to the new Extender network On your wireless device laptop tablet smartphone gaming console etc use the wireless manager to find the new Extender network mentioned above and connect For example on a laptop you might use Windows WiFi manager as shown below to connect your PC to the new Extender network Not connected aff Connections are available Wireless Network Connection NETGEAR_EXT i Last step once you have reconnected your device running this Wizard please mark the checkbox and click the Continue but
6. irelessly to your WiFi router or access point or Blu ray player WiFi router gt To connect an Ethernet enabled device to your WiFi router or access point 1 Set up the extender For more information see Place the Extender and Apply Power on page 5 2 Connectthe extender to an existing WiFi network For more information see Connect to an Existing WiFi Network on page 5 3 Plug the Ethernet cable from an Ethernet enabled device to the Ethernet port on the extender 14 Install the Extender as an Access Point You can also use the extender as a WiFi access point which creates a new AC750 WiFi hotspot within your local network 15 N To install the extender as an access point Set the Access Point Extender switch to Access Point Plug the extender into an electrical outlet near a router Ethernet LAN port or a remote Ethernet jack that has access to your local area network LAN Use an Ethernet cable to connect the extender to the router Ethernet LAN port or the remote Ethernet LAN jack with LAN access The extender joins the LAN and creates a WiFi hotspot On your computer or mobile device find and join a WiFi extender network The extender is dual band so it has two WiFi networks e 2 4 GHz network EX6100 NETGEAR _2GEXT e 5 GHz network EX6100 NETGEAR_5GEXT When you join the network the extender Client Link LED lights to show that you are connected Launch a web browser a
7. lick the Continue button Enter names SSIDs for your new extender WiFi network in the Name 2 4G SSID and Name 5G SSID fields and click the Continue button Step 1 Select the WiFi Network F Step 2 Set Up the Extender Name 2 4G SSID intgrwlan_2GEXT Name 5G SSID intarwlan_5q_5GEXT Step 3 Apply Settings Y Use the existing securiy mode and password settings Enter the settings for the Extender network Note You can use the same security settings as your existing network by selecting the check box The settings are applied and the following screen displays You are now one step away from completing the installation Step 1 Select the WiFi Network 0 Your Extender network has been created Extender network 2 4GHz b g n Extender network 5GHz a n ac Step 2 Set Up the Wireless network name SSID ntgrwlan_2GEXT Wireless network name SSID ntgrwlan_5g_5GEXT Extender pu Security type WPA2 PSK Security type WPA2 PSK Passphrase Passphrase Step 3 Apply Settings Now you need to reconnect your wireless device s to the new Extender network On your wireless device laptop tablet smartphone gaming console etc use the wireless manager to find the new Extender network mentioned above and connect For example on a laptop you might use Windows WiFi manager as shown below to connect your PC to the new Extender network Not connected aiil Connections are available Wirel
8. n closer to the area with a poor WiFi signal The location you choose must be within the range of your existing WiFi router network 7 Plug the extender into an electrical outlet and wait one minute The Power LED lights green If the Power LED does not light press the Power button Use the Router Link LED on the front panel to help you choose a spot where the extender to router connection is optimal Connect with NETGEAR genie Smart Setup 1 Make sure that the switch on the extender is set to Extender 2 Use a WiFi network manager on a computer or mobile device to find and connect to one of the extender WiFi networks The extender is dual band so it has two WiFi networks e 2 4 GHz network EX6100_ NETGEAR_2GEXT e 5 GHz network EX6100 NETGEAR_5GEXT After the connection with the computer or mobile device is established the Client Link LED N lights solid green 3 Open a web browser window from the same computer or mobile device The browser takes you directly to the NETGEAR genie smart setup Note If you are not automatically directed to NETGEAR genie launch a web browser and enter www mywifiext net in the address field Enter admin for the user name and password for the password Select a 2 4 GHz WiFi network to extend and click the Continue button Select the name of your 2 4GHz WiFi network Step 1 Select the WiFi Network The Extender supports dual bands 2 4GHz and 5GHz Select the 2 4GHz WiFi ne
9. nd enter www mywifiext net in the address field Enter admin for the user name and password for the password NETGEAR genie displays and detects the Internet connection Follow the genie steps to set up WiFi security for both WiFi networks Access Extender Settings After installation you can log in to the extender to view or change the extender s settings gt To log in to the extender after the initial setup 1 Connect a computer or mobile device to the extender s network 2 Launch a web browser and enter www mywifiext net in the address field A login screen displays 3 Enter admin for the user name and password for the password Frequently Asked Questions You can find more information about your product in the user manual which is available at http support netgear com The web browser setup guide keeps asking me for my network security key passphrase and am sure have entered the correct passphrase What can do The extender is probably placed at the borderline of the range covered by the router or access point For more information see Place the Extender and Apply Power on page 5 If you are using WEP security make sure that you are typing the wireless key in the correct field What are the user name and password to log in to the extender The user name is admin and the default password is password Both are case sensitive Will the extender work if connect it to the router with an Ether
10. net cable It depends If the switch is set to Extender the extender connects to the router over WiFi If the switch is set to Access Point the extender connects to the router with an Ethernet cable I am connected to EX6100 NETGEAR_2GEXT or EX6100 NETGEAR_5GEXT and launched a browser Why can t see the web browser setup genie Try these troubleshooting steps e Make sure that your computer is set up to use DHCP most are e Make sure that the Client Link LED is green and that you have a valid IP address e Relaunch the web browser and type www mywifiext net or www mywifiext com in the address field of the web browser Enter admin for the user name and password for the password How do I restore the extender to its factory default settings 1 Use a sharp object such as a pen or paper clip to press and hold the Factory Reset button on the extender for at least five seconds until the Power LED blinks amber 2 Release the Factory Reset button and wait for the extender to reboot The extender resets and returns to the factory default settings You can now access the extender from your web browser using the factory default settings Support Thank you for selecting NETGEAR products After installing your device locate the serial number on the label of your product and use it to register your product at https my netgear com You must register your product before you can use NETGEAR telephone support NETGEAR recommen
11. ton to finalize your installation Unplug the extender and move it to a new location closer to the area with a poor WiFi signal The location you choose must be within the range of your existing WiFi router network Plug the extender into an electrical outlet and wait one minute The Power LED lights green If the Power LED does not light press the Power button Use the Router Link LED on the front panel to help you choose a spot where the extender to router connection is optimal 11 Find the Best Location If the WiFi signal is weak the first time you join the extender network an arrow LED blinks for two minutes If this happens adjust the position of the extender No any LEDs are lit The extender is in a good location SUE dm 4 Left arrow blinks Move the extender closer to the router vl Ko Right arrow blinks Move the computer or mobile device closer to the extender Extender Performance These extender LEDs indicate a WiFi connection di WiFi signal between the router and the extender I WiFi signal between the extender and the computer or mobile device The LEDs are color coded e Green indicates the best connection e Amber indicates a good connection e Red indicates a poor connection An LED that is off indicates no WiFi connection 12 Connect an Ethernet Enabled Device After the extender is connected to your existing WiFi network you can use the extender to connect a device w
12. twork that you want to connect to and then click the Continue or click the Skip button to select 5GHz network se karie oin Skip Refresh Continue Extender n SSID Channel Signal Security 7 z NETGEAR16 1 100 WPA2 PSK Step 3 Apply Settings 3700v4 Lance_2GEXT 1 100 WPA2 PSK P NETGEAR85 1 100 WPA2 PSK NETGEAR62 6 100 WPA2 PSK ngguest 9 100 WPA2 PSK jw2 11 100 WPA2 PSK ntgrwlan 9 100 WPA2 PSK KC3ANN 4G 2GFXT DRG 1 100 WPANNPA2 PSK Type the network password also called passphrase or security key in the Password field and click the Continue button Select a 5 GHz WiFi network to extend and click the Continue button If your router does not support the 5 GHz band click the Skip button Select the name of your 5GHz WiFi network Step 1 Select the WiFi amp amp E E E Z gt ee Network SSID Channel Signal Security Step 2 Set Up the ngguest_5g 149 100 WPA2 PSK yorouter_5G_N_5GEXT 153 100 WPANNPA2 PSK Extender NETGEAR34 5G 153 100 WPA2 PSK NETGEAR85 5G 153 100 WPA2 PSK Step 3 Apply Settings ntgrwlan_5g 149 100 WPA2 PSK i NETGEAR16 5G 153 99 WPA2 PSK GodSpeed_5g 153 99 WPA2 PSK NETGEAR62 5G 153 96 WPA2 PSK ririnntA44 A1R7 na WDAN DOI Type the network password also called passphrase or security key in the Password field and click the Continue button Select the Private Network or Public Network radio button and c
Download Pdf Manuals
Related Search