N-Tron 300 User's Manual
Contents
1. IN TRON THE INDUSTRIAL NETWORK COMPANY 300 Series Media Converter amp Industrial Ethernet Switches Installation Guide 12 29 2005 IN TRON THE INDUSTRIAL NETWORK COMPANY Industrial Ethernet Switch Installation Guide 302MC XX 302MCE XX YY 304TX 305FX XX 305FXE XX YY 306TX 306FX2 XX 306FXE2 XX Y Y 308TX Where XX ST or SC and YY 15 40 or 80 12 29 2005 O LNK ACT LNK ACT Copyright N TRON Corp 2005 820 S University Blvd Suite 4E Mobile AL 36609 USA All rights reserved Reproduction adaptation or translation without prior written permission from N TRON Corp is prohibited except as allowed under copyright laws Ethernet is a registered trademark of Xerox Corporation All other product names company names logos or other designations mentioned herein are trademarks of their respective owners The information contained in this document is subject to change without notice N TRON Corp makes no warranty of any kind with regard to this material including but not limited to the implied warranties of merchantability or fitness for a particular purpose In no event shall N TRON Corp be liable for any incidental special indirect or consequential damages whatsoever included but not limited to lost profits arising out of errors or omissions in this manual or the information contained herein Warning Do not perform any services on the unit unless qualified to do so Do2. Weight Electrical Input Voltage Input Current Inrush Current Input Ripple Input Wire Size Environmental Operating Temperature Storage Temperature Operating Humidity Operating Altitude Network Media 10BaseT I00BaseT I00BaseFX 3 98 max 2 01 max 4 19 max 0 75 Ibs 10 30 VDC Regulated 290mA max 24VDC Steady State 8 0Amp 0 6ms max 24VDC Less than 100 mV 16 28 AWG 20 C to 70 C 20 C to 85 C 10 to 90 Non Condensing 0 to 10 000 ft Cat 3 Cable Cat 5 Cable Multimode 50 62 5 125um Fiber Singlemode 7 9 125um Fiber Fiber Transceiver Characteristics Fiber Length TX Power Min RX Sensitivity Max Wavelength Connectors 2km l5km 40km SOkm 19dBm SdBm 5dBm 5dBm 32dBm 29dBm 34dBm 34dBm 1310nm 1310nm 1310nm 1550nm Multimode Singlemode 10 100BaseT RJ45 UTP Ports 100BaseFX SC or ST Duplex Port s Gf equipped Recommended Minimum Wiring Clearance Front 2 5 08 cm for 304TX 306TX amp 308TX models 5 12 7 cm for 302MC 305FX amp 306FX2 models Side 1 2 54 cm Emissions and Safety Approvals FCC Part 15 Class A CE Warranty 1 year from the date of purchase 12 29 2005 12 N TRON Limited Warranty N TRON Corp warrants to the end user that this hardware product will be free from defects in workmanship and materials under normal use and service for the applicable warranty period from the
3. not substitute unauthorized parts or make unauthorized modifications to the unit Do not operate the unit with the top cover removed as this could create a shock or fire hazard Do not block the air vents on the sides or the top of the unit Do not operate the equipment in the presence of flammable gasses or fumes Operating electrical equipment in such an environment constitutes a definite safety hazard 12 29 2005 Safety Warnings ELECTRICAL SAFETY WARNING Disconnect the power cable before removing the enclosure top WARNING Do not operate the unit with the top cover removed WARNING Do not work on equipment or cables during periods of lightning activity WARNING Do not perform any services on the unit unless qualified to do so WARNING Do not block the air vents WARNING Observe proper DC Voltage polarity when installing power input cables Reversing voltage polarity can cause permanent damage to the unit and void the warranty LASER SAFETY FXE Products Only WARNING CLASS 1 Laser Product Do not stare into the laser 12 29 2005 Hazardous Location Installation Requirements 1 WARNING Do not disconnect while circuit is live unless area is known to be non hazardous 2 WARNING Install only in accordance with Local amp National Codes of Authorities Having Jurisdiction 3 Class I Div 2 Installations require that power connections must be current limited at the power source with an in line fuse ra
4. unit to allow at least 5 of horizontal clearance for fiber optic cable bend radius 2 for TX models To install the unit to 35mm industrial DIN Rail place To remove the unit from the 35mm industrial DIN Rail the top edge of the included mounting bracket on the back place a flat head screwdriver into the orange release clip of the unit against the DIN Rail at a 15 angle as shown found at the bottom of the unit and apply downward force Rotate the bottom of the unit to the back away from you on the clip until it disengages from the bottom of the unit until it snaps into place from the DIN Rail Rotate the bottom of the unit towards you and up at an approximate 15 upward angle to completely remove the unit With the exception of the 524TX and 526FX2 all N Tron products are designed to be mounted on industry standard 35mm DIN Rail However DIN Rail mounting may not be suitable for all applications We offer 300 PM 900 PM three alternative mounting solutions Our 300 Panel Mount Assembly P N 300 PM may be used to mount a single 300 Series unit to a panel or other flat surface Our 900 Panel Mount Assembly P N 900 PM may be used to securely mount our 100 200 300 400 500 or 900 Series products to a panel or other flat surface Our Rack Mount Assembly 900 RM P N 900 RM may be used to mount our products to standard 19 racks 12 29 2005 E TUE FRONT PANEL LNK Link LED for Fiber Optic Ports T
5. EMENT ALL OF WHICH ARE EXPRESSLY DISCLAIMED N TRON NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE OR USE OF ITS PRODUCTS N TRON SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT OR MALFUNCTION IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER S OR ANY THIRD PERSON S MISUSE NEGLECT IMPROPER INSTALLATION OR TESTING UNAUTHORIZED ATTEMPTS TO OPEN REPAIR OR MODIFY THE PRODUCT OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE OR BY ACCIDENT FIRE LIGHTNING POWER CUTS OR OUTAGES OTHER HAZARDS OR ACTS OF GOD LIMITATION OF LIABILITY TO THE FULL EXTENT ALLOWED BY LAW N TRON ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY WHETHER BASED IN CONTRACT OR TORT INCLUDING NEGLIGENCE FOR INCIDENTAL CONSEQUENTIAL INDIRECT SPECIAL OR PUNITIVE DAMAGES OF ANY KIND OR FOR LOSS OF REVENUE OR PROFITS LOSS OF BUSINESS LOSS OF INFORMATION OR DATA OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE USE PERFORMANCE FAILURE OR INTERRUPTION OF ITS PRODUCTS EVEN IF N TRON OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES AND LIMITS ITS LIABILITY TO REPAIR REPLACEMENT OR REFUND OF THE PURCHASE PRICE PAID AT N TRON S OPTION THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHAL
6. L FAIL OF ITS ESSENTIAL PURPOSE DISCLAIMER Some countries states or provinces do not allow the exclusion or limitation of implied warranties or the limitation of incidental or consequential damages for certain products supplied to consumers or the limitation of liability for personal injury so the above limitations and exclusions may be limited in their application to you When the implied warranties are not allowed to be excluded in their entirety they will be limited to the duration of the applicable written warranty This warranty gives you specific legal rights which may vary depending on local law GOVERNING LAW This Limited Warranty shall be governed by the laws of the State of Alabama U S A 12 29 2005 13
7. X Fiber Optic Transmit Ports RX Fiber Optic Receive Ports ACT Activity LED for Fiber Optic Ports RJ45 Ports Ports 1 4 Auto sensing 10 100BaseT Connections d Green LED lights when Power is connected NOTE Each RJ45 data port has two LED s for each connector The lower LED indicates LINK status and the upper LED indicates ACTIVITY LED s The table below describes the operating modes Description Power is Applied Power is OFF Link between ports established No Link between ports Data is active between ports Data is inactive between ports 12 29 2005 APPLYING POWER Top View FONT EON CONNEXES a a ONE CONCORDE ON CO OEOTCO IE E ORO EON S Unscrew amp Remove the DC Voltage Input Plug from the top header Install the DC Power Cables into the Plug observing polarity on unit Plug the Voltage Input Plug back into the top header All LED s will flash ON Momentarily Verify the Power LED stays ON GREEN Note Either V1 or V2 can be connected to power for minimal operation For redundant power operation V and V plugs must be connected to separate DC Voltage sources Use wire sizes of 16 28 gauge The power cord should be limited to less than 10 meters in order to ensure optimum performance Recommended 24V DC Power Supplies similar to 100VAC 240V AC N Tron s NTPS 24 1 3 DC 24V 1 3A Operating temp range 10 C to 60 C CONNECTING THE UNIT For 300 Series fiber units remove the dust cap from th
8. data of purchase from N TRON or its authorized reseller If a product does not operate as warranted during the applicable warranty period N TRON shall at its option and expense repair the defective product or part deliver to customer an equivalent product or part to replace the defective item or refund to customer the purchase price paid for the defective product AII products that are replaced will become the property of N TRON Replacement products may be new or reconditioned Any replaced or repaired product or part has a ninety 90 day warranty or the remainder of the initial warranty period whichever is longer N TRON shall not be responsible for any custom software or firmware configuration information or memory data of customer contained in stored on or integrated with any products returned to N TRON pursuant to any warranty OBTAINING WARRANTY SERVICE Customer must contact N TRON within the applicable warranty period to obtain warranty service authorization Dated proof of purchase from N TRON or its authorized reseller may be required Products returned to N TRON must be pre authorized by N TRON with a Return Material Authorization RMA number marked on the outside of the package and sent prepaid and packaged appropriately for safe shipment Responsibility for loss or damage does not transfer to N TRON until the returned item is received by N TRON The repaired or replaced item will be shipped to the customer at N TRON s expense not late
9. e fiber optic connectors and connect the fiber optic cables For Fiber Optic ports the T X port on the near station should be connected to the RX port of the far end station and the RX port should be connected to the TX port of the far end station For 10Base T ports plug a Category 3 or greater twisted pair cable into the RJ45 connector For 100Base T ports plug a Category 5 or greater twisted pair cable into the RJ45 connector Connect the other end to the far end station Verify that the LNK LED s are ON once the connection has been completed To connect any other port to another Switch or Repeater use a standard Cat5 straight through or crossover cable 12 29 2005 10 TROUBLESHOOTING 1 Make sure the Power LED is ON 2 Verify that Link LED s are ON for connected ports 3 Verify cabling used between stations 4 Verify that cabling is Category 5 or greater for 100Mbit Operation 5 Verify TX is connected to far end RX and vise versa fiber optic units only SUPPORT Contact N TRON Corp at TEL 251 342 2164 FAX 251 342 6353 WWW n tron com support n tron com FCC STATEMENT This product complies with Part 15 of the FCC A Rules Operation is subject to the following conditions 1 This device may not cause harmful Interference 2 This device must accept any interference received including interference that may cause undesired operation 12 29 2005 11 KEY SPECIFICATIONS Physical Height Width Depth
10. e fiber transceiver s that are capable of 15 40 and up to 80 Kilometers of 100 Mb full duplex communications All fiber products utilize the IEEE compliant SC or ST duplex connectors for fiber optic communications All 10 100Base TX ports utilize the RJ45 shielded connectors Key Features Full IEEE 802 3 amp 100Base FX Compliance Extended Environmental Specifications Support for Full Half Duplex Operation LED Link Activity Status Indication Autonegotiation Autosensing Speed Duplex and Flow Control Up to 1 0 Gb s Maximum Throughput Industry Standard 35mm DIN Rail Mounted Enclosure 12 29 2005 PACKAGE CONTENTS Please make sure the Ethernet Switch package contains the following items 1 300 Series Unit 2 N Tron Product CD Contact your carrier if any items are damaged INSTALLATION Read the following warning before beginning the installation WARNING FXE units contain a class laser Do not stare into the laser beam fiber optic connector when installing or operating the product Never install or work on electrical equipment or cabling during periods of lightning activity Disconnect the power cable before removing the enclosure top Do not operate the unit with the top cover removed UNPACKING Remove all the equipment from the packaging and store the packaging in a safe place File any damage claims with the carrier 12 29 2005 DIN Rail Mounting Install the unit in a standard DIN Rail Recess the
11. r than thirty 30 days after N TRON receives the product N TRON shall not be responsible for any software firmware information or memory data of customer contained in stored on or integrated with any products returned to N TRON for repair whether under warranty or not ADVANCE REPLACEMENT OPTION Upon registration this product qualifies for advance replacement A replacement product will be shipped within three 3 days after verification by N TRON that the product is considered defective The shipment of advance replacement products is subject to local legal requirements and may not be available in all locations When an advance replacement is provided and customer fails to return the original product to N TRON within fifteen 15 days after shipment of the replacement N TRON will charge customer for the replacement product at list price WARRANTIES EXCLUSIVE IF AN N TRON PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE CUSTOMER S SOLE REMEDY FOR BREACH OF THAT WARRANTY SHALL BE REPAIR REPLACEMENT OR REFUND OF THE PURCHASE PRICE PAID AT N TRON S OPTION TO THE FULL EXTENT ALLOWED BY LAW THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES TERMS OR CONDITIONS EXPRESS OR IMPLIED EITHER IN FACT OR BY OPERATION OF LAW STATUTORY OR OTHERWISE INCLUDING WARRANTIES TERMS OR CONDITIONS OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE SATISFACTORY QUALITY CORRESPONDENCE WITH DESCRIPTION AND NON INFRING
12. ted at 0 5A 4 Class I Div 2 installations require that all devices connected to this product must be UL approved for the area in which it is installed 5 Only UL approved wiring with temperature ratings greater than 90 C permitted for Class I Div 2 installations operating at temperatures up to70 C ambient 6 Limited Operating Voltage 12 30V for Class I Div 2 installations 12 29 2005 5 300 Series Industrial Ethernet Switches The 300 Series Unmanaged Industrial Ethernet Switches support high speed layer 2 switching between ports All N TRON 300 Series switches are housed in a ruggedized steel enclosure and provide Category 5 compliant 10 100 BaseT connections for high performance network design and hub repeater upgrades The 302MC MCE is a 2 port unmanaged media converter that converts 10 100BaseTX copper to 100BaseFX full duplex fiber The 304 TX 306TX and 308TX are affordable and share a small footprint Each switch is capable of auto negotiating 10 100 Mb and half full duplex communications The 305FX and 306FX2 switches are unmanaged and have 4 ports similar to the 304 TX plus an additional multimode fiber optic up link port s capable of 2 Kilometers of 100 Mb communications without the use of repeaters The 305FXE and 306FXE2 switches are unmanaged and similar to the 305FX and 306FX2 respectively However these models use singlemode transceivers with extended range capability The N TRON FXE products utilize singlemod
Download Pdf Manuals
Related Search