Morphy Richards 28037 User's Manual
Contents
1. Guarantee Morphy Richards products are manufactured to internationally accepted quality standards In addition to your statutory rights Morphy Richards guarantee your product to be free from manufacturing and component defects for a period of TWO YEARS from date of purchase If your product proves to be defective within 28 days of purchase your Morphy Richards dealer from whom the product was purchased will be pleased to replace it free of charge Should your product develop a defect within the guarantee period but after the replacement period please return the product to the following address together with the proof of purchase brief details of the symptoms and your own name and address After Sales Division Morphy Richards Limited Talbot Road Mexborough South Yorkshire S64 8AJ Your post office will provide a certificate of posting The product will be repaired and returned to you promptly If you need any further advice please call our Helpline on 0870 060 2614 Mon Fri www morphyrichards co uk 446 8004 10 Rev1 Morphy Richards Ltd Talbot Road Mexborough S64 8AJ Morphy Richards products are intended for household use only Morphy Richards has a policy of continuous improvement in product quality and design The company therefore reserves the right to change the specification of its models at any time2. To stop the alarm tone either set to radio or buzzer The alarm is programmed to run for 2 hours 1 To stop the alarm press the ALARM button The alarm will stop and will operate again 24 hours later 2 To stop the alarm temporarily press the SNOOZE button The alarm will sound again 9 minutes later 3 To switch the alarm setting off permanently slide the FUNCTION SELECTOR switch to the Off position Snooze function The alarm can be interrupted for a 9 minute period 1 Press the SNOOZE button after 9 minutes the radio or alarm buzzer will sound again To set the sleep function Your clock radio is equipped with a sleep function that will turn the radio on and switch it off automatically after a set period of time from between 59 minutes to 1 minute Pressing the hour button will extend the sleep time to 1 hour 59 minutes 1 Press the SLEEP button the clock display will show 0 59 sleep time at the same time the radio will come on and stay on for 59 minutes Ensure the VOLUME control has not been set to alarm buzzer mode 2 Press and hold the SLEEP button whilst pressing the MINUTE button or HOUR button the sleep time shown on the clock display will start descending 3 Release all buttons when the desired sleep time is shown on the clock display 4 After the set sleep time has elapsed the radio will automatically switch off 5 To switch off before the set sleep time has elapsed press the SNOOZE button P 6
3. waveband is located inside the unit To obtain the maximum MW reception rotate the clock radio 1 Slide the FUNCTION SELECTOR switch to the ON position 2 Adjust the VOLUME control to a suitable level 3 Set the BAND SELECTOR switch to either MW or FM as desired 4 Slowly adjust the TUNING control to select your desired station 5 To switch off the radio slide the FUNCTION SELECTOR switch to the OFF position P4 Alarm operation 1 Press and hold the ALARM button and simultaneously press the HOUR or MINUTE button to set the display to the desired alarm time Release the ALARM button to set the alarm time 2 Set the FUNCTION SELECTOR switch to the AUTO alarm position The ALARM ON indicator will appear on the clock display Wake up to the radio alarm 1 Switch the FUNCTION SELECTOR switch to the ON position to tune to the desired station 2 Set the BAND SELECTOR switch to select either FM or MW wavebands as desired 3 Adjust the VOLUME control to a suitable level 4 Slowly adjust the TUNING control to the desired station 5 Slide the FUNCTION SELECTOR switch to the AUTO position The ALARM ON indicator will light The radio station will wake you up at the set alarm time The alarm will automatically turn off after 2 hours Ensure the station you select will be transmitting at the preset alarm time Wake up to the alarm buzzer In order to check that the correct alarm time has been set press
4. l need to reset the clock and alarm Battery back up is designed to operate for a short period only If the unit is not to be used for a prolonged period remove the battery to avoid battery leakage In the interests of environmental safety dispose of batteries safely P3 Illustration Location of controls 1 Function selector switch 9 Clock display 2 Volume control 10 Minute button 3 Band selector 11 Snooze button 4 Tuning control 12 Alarm indicator 5 FMwire aerial 13 PM indicator 6 Speaker 14 Time button 7 Alarm button 15 Sleep button 8 Hour button 16 Battery compartment underneath unit P2 Switching on and setting the clock time Before any alarm functions can be used on your alarm clock radio you must first set the clock to the correct time 1 Place the unit on a flat surface Plug the mains plug into the wall socket and switch on the wall socket 2 The clock LED display will flash 3 Press and hold the TIME button and simultaneously hold down the hour button or the minute button The LED clock display will fast forward the minutes and hour segments Release all buttons when the correct time is set 4 The PM indicator will illuminate to indicate 12 00 midday has been reached Radio operation FM wire aerial To obtain the maximum FM reception fully extend the wire FM aerial which is located at the rear of the unit and alter the direction of the wire for best results The aerial for the MW
5. morphy richards 2 Band Alarm Clock Radio 28037 OPERATING INSTRUCTIONS Electrical requirements Check the voltage on the rating plate of your clock radio corresponds with your house electricity supply which must be A C Alternating current For clock radios with a fitted plug If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted IMPORTANT THE PLUG REMOVED FROM THE MAINS LEAD IF SEVERED MUST BE DESTROYED AS A PLUG WITH A BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED INTO A LIVE SOCKET OUTLET Should the fuse in the 13 amp plug require changing a 3 amp BS1362 fuse must be fitted Battery back up facility unit will work without a battery being fitted Your alarm clock radio is equipped with a battery back up facility 1 Remove the battery compartment cover located underneath the unit by pushing in the clip and lifting off 2 Insert a battery size 9 volts PP3 6LR61 Ensure batteries are inserted correctly 3 Replace the battery compartment cover Should a power interruption occur the clock will continue to run however time keeping will not be accurate The display will be extinguished to conserve battery life but the memory will retain details of the clock time and alarm settings If the optional battery is not installed in case of the AC power failure the display will blink to indicate the power was interrupted You wil
6. the ALARM button The display will indicate the alarm time set 1 Slide the FUNCTION SELECTOR switch to the AUTO position The ALARM ON indicator will light Rotate the VOLUME control clockwise until a click is heard The buzzer alarm will wake you up at the set alarm time The buzzer will automatically turn off after 2 hours PS Maintenance Do not expose your clock radio to extremes of temperature The product should be kept in a warm environment free from dust and damp For external cleaning use only a soft clean damp cloth Use of detergents may damage the finish Technical specification AC Power supply 230v 50Hz Battery back up f 9V DC type 6LR61 PP3 not included Radio i FM 88Mhz 108Mhz MW 540Khz 1600Khz Warning labels WARNING to reduce the risk of electric shock do not expose this appliance to rain or moisture CAUTION ATTENTION To reduce the risk of electric shock do not RISK OF ELECTRIC SHOCK remove the cover There are no user serviceable parts inside DO NOT OPEN the unit Refer any servicing to qualified personnel The lightning flash with arrowhead symbol within the triangle is a warning sign alerting the user of dangerous voltage inside the unit The exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying the product gt gt To prevent fire or shock hazard do not expose this apparatus to dripping or splashing P 7
Download Pdf Manuals
Related Search