Miele F 1411 SF Operating and Installation Instructions
Contents
1. Hammer Open ended wrench 1 2 SW 13 mm Box end wrench 46 8 mm hex nut driver Adhesive tape Multi grip pliers Level Metal tape measure Square Other Stepladder Dolly hand truck Wooden beam cross section min 3 x 4 75 mm x 100 mm as an alternative tilt protection length depends on the width of the installation cavity Wood screws in different sizes Edge protector s Optional accessories Merging Kit for side by side installation RemoteVision module for wireless monitoring 53 Installing the appliance Aligning the housing unit The housing unit must be carefully aligned using a spirit level before installing the appliance The unit corners must be at right angles as otherwise the furniture door will not align correctly with the 4 corners of the appliance The side panels of the housing must be even The housing unit panels must be at least 16 mm thick The plinth facing must be at least 13 mm thick or preferably 19 mm 54 Check the installation niche To ensure a safe trouble free installation and the best possible cosmetic result check to be sure that the installation space complies with the installation requirements m Check the base see Installation m Check the dimensions of the cavity m Check that the cavity is square m Check the location of the power outle2. Using an external water filter filter If your household water supply already has an external water filter installed leave the standard water filter bypass wc ee enangedne MET cartridge installed in the appliance indicator in the display still flashes The change must be be confirmed in the electronic Confirming the filter change filter m Press and hold the filter change sensor button m At the same time place a finger on the access button Press and hold both sensor buttons for approx 5 seconds until a beep is heard The water filter change has been confirmed and the filter change indicator had been reset The filter change indicator goes out m Close the door After installing a new water filter discard the first 24 hours of ice production 32 Water filter State of California Department of Public Health Water Treatment Device Certificate Number 06 1775 Date Issued March 10 2006 Date Revised April 3 2008 Trademark Model Designation Replacement Elements 9000 077095 9000 077104 Miele 07134220 07134220 Manufacturer Cuno Incorporated The water treatment device s listed on this certificate have met the testing requirements pursuant to Section 116830 of the Health and Safety Code for the following health related contaminants Microbiological Contaminants and Turbidity Inorganic Radiological Contaminants Cysts None Turbidity Organic Contaminants None
3. Issue Possible fault Solution The ice cubes are small Other domestic appliances that use water are in operation Avoid using such items as a dishwasher washing machine or shower at the same time Check whether the water fil ter needs changing See Water filter for more information Check the water pressure The water pressure must be between 25 and 120 psi 1 72 8 25 bar Consult a plumber Check whether the correct water valve has been installed Self tapping valves and 3 46 4 76 mm saddle valves reduce the water pressure and can block the pipe The ice cubes have an unpleasant odor flavor When ice is stored for an extended period it may absorb odors which affects the taste Use the ice maker more frequently Check if the ice cube container is dirty Clean the container Unsealed packages in the freezer will transfer odor flavor particles to the ice cubes Check that food has been packed in airtight containers 40 Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice maker is not producing enough ice or the ice cubes are misshapen Check the water pressure The water pressure must be between 25 and 120 psi 1 72 8 25 bar Contact a plumber Check that the freezer temperature is too high See Selecting the correct temperature Change the
4. The door has been opened too frequently or a large amount of unfrozen food has been put in at once for freezing Once the freezer gets down to the set temperature the compressor will turn off The door is not closed Check that the door has been closed properly The freezer runs continuously To save energy the compressor runs at a lower speed but for longer when less cooling is required The temperature reading in the freezer shows 18 C although a higher temperature is set This is not abnormal When the ice maker is in use and the temperature of the room is above freezing the temperature automatically stays at 18 C to ensure proper functioning 37 Frequently asked questions Alarm Indicator warnings Issue Possible fault Solution The alarm is going off The appliance door s have been open for longer than 5 minutes Close the door The alarm is ringing and the alarm indicator is flashing The door is not closed A large amount of food is being frozen at the same time There has been a power failure Once the alarm condition has been corrected the alarm will turn off and the alarm indicator will stop flashing The filter display is red This is a warning that the water filter needs to be changed soon Order replacement filters from Miele The filter display is flashing red The water filter ne
5. The moisture generated in the appliance collects in the evaporator It is automatically defrosted and dissipated by the condenser periodically This automatic defrosting system enables the freezer to remain permanently ice free while ensuring that the food stored in the freezer stays frozen 22 Adjusting the interior fittings Moving the shelves The shelves can be adjusted according to the height of the food m Using both hands grasp the shelf from underneath and lift slightly so that the rear of the shelf is slightly above the mountings m Pull the shelf forward m Move the shelf to the desired height then insert the rear hooks into place m Make sure the shelf is level Top shelf m Lift the shelf up and out m When replacing the shelf make sure that the latches on the corners at the back are correctly engaged Adjusting the door shelves For easier loading unloading and cleaning the door shelves can be shifted or completely removed m Using both hands grasp the door shelf by the frame and tip it slightly forward m Slide the tipped shelf up or down along the slide rails and click it into place with the lower hooks m Make sure the shelf is level Removing a door shelf m Slide it upward all the way to the top of the slide rails until it can be removed Replacing a door shelf m Start at the top of the slide rails and slide the shelf down into the desired position Freeze
6. Rated Service Capacity 740 gals Rated Service Flow 0 75 gpm Conditions of Certification Do not use where water is microbiologically unsafe or with water of unknown quality except that systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts 33 Water filter Performance Data Sheet For Filter Model 07134220 Using Replacement Cartridge 07134220 This system has been tested according to NSF ANSI Standards 42 and 53 for the reduction of the substances listed below The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system as specified in NSF ANSI 42 and 53 System tested and certified by NSF International in Model 07134220 Note that while the testing was against NSF ANSI Standard 53 for the reduction of Cysts and Performed under standard Turbidity and against Standard 42 for the reduction of Chlorine Taste laboratory conditions actual and Odor Nominal Particulate Class performance may vary To a capacity of 739 68 gallons 2800 liters Substance Average Influent Challenge Product d Maximum Permissible Max Min 96 NSF Influent Concentration Water Product Water Effluent Reduction Test Concentration mg L Concentration Bain Concentration Cysts 166500 Minimum 50 000 L 1 99 99 99 95 9999 516458 05 Turbidity 107 11 1NTU 0 31 97 09
7. damage electrical components and cause a short circuit IMPORTANT SAFETY INSTRUCTIONS Disposal of your old appliance P Before disposing of an old appliance first make the door latch or lock unusable P Take off the door P Leave the shelves in place so that children may not easily climb inside P Consult with your municipal policy on recycling P Be careful not to damage any part of the pipework while awaiting disposal by puncturing the refrigerant channels in the evaporator bending any pipework scratching the surface coating Splashes of refrigerant can damage the eyes P Your old freezer may have a cooling System that used CFCs chlorofluorocarbons CFCs are believed to harm stratospheric ozone If you intentionally release this CFC refrigerant you can be subject to fines and imprisonment under provisions of environmental legislation Make sure the CFC refrigerant is removed and disposed of by a qualified technician SAVE THESE INSTRUCTIONS Guide to the freezer Door shelves height adjustable 2 Shelves height adjustable Ice cube maker 2 Ice cube container 8 Control panel Main switch to turn the appliance On Off 2 Freezer baskets 8 Water filter Guide to the freezer Control panel super ice alarm filter ee e D Access button 2 Temperature display V colder warmer Allows you to set the
8. 2290 www miele ca professionalQmiele ca commercial enquiries MieleCare National Service Phone 800 565 6435 905 532 2272 Fax 905 532 2292 customercareQmiele ca general and technical enquries Alteration rights reserved 3613 M Nr 09 743 950 00 INFORMATION IS SUBJECT TO CHANGE PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS TECHNICAL amp WARRANTY INFORMATION
9. Ee E ead RR En a e ees 23 Freezer baskets 25e ded bed ORE RE ord lesen dd b ied rhet doped a 23 Ice CUbe CODtelblbfs x esos qe etre emp aede ore fede Raya taa TE de die haa gon 24 Cleaning and care 0 0 0 e 25 Cleaning the interior and accessories ill lesen 26 ADplIanee dOr ica ata ird Set OR teer Sattel anges d ote oO a atio det 26 VentllatiOnislits x acis er ete adie ay EE UU e P OR a Pg s f db M pale de A 27 DOOR SS aS ER ERRORI 27 Changing the light bulb i e e m RR dese ees 28 Water filter esu ee ee dengue Peat eels Bee a s A edo owe 30 Water filter change indicator iilii 30 Exchanging the water filter ciii 31 Confirming the filter change issselsssss 32 Using an external water filler 222i 32 Lead free certificate loli iil ees 35 Frequently asked questions nunaa 36 Contents After sales service olli iles 42 Caring for the environment iiiiisiis eile essel 44 Installation en mee buo Baer eno Lave Khai a E ae ed RU aa 45 Installation Siess see tg ren er eb eod e ue Ede A v PERLES D 45 Stainless steel panels 2 0 0 0 2 e 48 Iistallation options uid stas p epe RE Ead he dob pote e tus 48 Dimerislols eo soe x hac De Red Pape UR pe Pa RR Ie e a CR RR RL opem a 50 Installing the appliance 0 0 0 0 00 53 Before you DEgiN 2 teens 53 RemoteVision module installation 2 eee 55 Preparing the installation nic
10. an air conditioned room with sufficient ventilation Please ensure that doors close and seal properly after installation and that the appliance is installed in accordance with these installation instructions and and with the required ventilation openings If the room is too cold it will cause the cooling system in the appliance to remain off for too long This can cause the temperature in the appliance to rise resulting in damage 46 Installation Base A fully loaded appliance is very heavy The load bearing capacity of your floor must meet the following requirements The approx weight of a fully loaded machine is F14141SF 626 Ibs 284 kg To ensure that the appliance is installed securely and functions properly the base must be flat level and made of a hard rigid material If in doubt contact Miele Furniture fixtures The new appliance will be mounted securely to adjacent and overhead furniture fixtures For this reason it is essential that all attachable furniture fixtures are connected securely to the base or the wall by suitable means Ventilation The air intake and outlet must not be blocked or covered in any way They also need to be dusted cleaned on a regular basis Installation niche To ensure safe trouble free installation and the best possible cosmetic result check to be sure that the installation space complies with the installation dimensions See Niche dime
11. before placing the appliance in its installation niche Once connected the RemoteVision module will increase the energy consumption of the appliance The slot for the RemoteVision module is located in the lower area of the back of your appliance m Unscrew the screws on the cover 2 and pull off the sticker m Remove the cover 2 55 Installing the appliance m Push the module into the slot until it locks into place m Connect the appliance to the power supply and turn it on After several seconds the indicator light will come on The indicator light will display different colors one after the other any control light at the end indicates that the module was correctly installed If the indicator light does not come on installation of the module was unsuccessful In that case repeat the process If that does not correct the problem contact Miele 56 m Pull the antenna 9 straight out m Guide the cover 2 over the antenna and screw on the cover m Angle the antenna so that it faces to the right or left If necessary disconnect the power supply and continue installing the appliance Preparing the installation niche N Keep the appliance door closed until it is securely fastened in the niche Tipping hazard Because of the size and weight of the appliance it is essential to ensure that the appliance cannot tip over once it has been mounted in the niche Installing th
12. desired temperature in the freezer 3 On Off sensor button for the SuperCool function ENN 4 On Off sensor button for the ice cube maker 8 Sensor button for the temperature and door alarm Water filter change indicator Only visible when the relevant function is activated Before use Before using for the first time The stainless steel surface of the appliance is protected with a plastic film which protects it during shipping Do not remove this protective film until the appliance has been completely installed After removing the protective film clean the exterior surface with the supplied stainless steel agent This will aid in preventing resoiling m Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap Dry with a soft cloth If the appliance was transported to the installation site horizontally leave the appliance standing upright for approx 8 hours before connecting it to the electrical supply This is very important to ensure correct functioning 10 Turning the appliance On Off m Open the appliance door m Turn the appliance On Off with the main switch The main switch is located on the right side underneath the control panel Once on the appliance begins cooling When the door is open the interior lights come on The access button will light in the control panel The preset temperatures factory default
13. settings are reached after a few hours Do not put any food in the appliance until the preset temperatures are reached N Turning off the appliance with the main switch does not safely isolate it from the power supply Settings Using the settings This appliance is operated with the use of touch keys activated by a finger An available button will appear white A selected button will appear yellow be m Touch the access button J so it turns yellow On the control panel you will see additional sensor buttons to operate the appliance These buttons allow you to adjust the temperature select the SuperCool function or turn the ice maker On Off For additional information see the corresponding sections in this manual be m To leave the settings menu touch the access button 8 so it turns white The last settings entered are stored If the access button is not pressed the display will go out after approx 30 secs The other sensor buttons now disappear from the control panel Additional settings In the settings mode you can select and change functions In settings mode certain settings can be changed The function possibilities are described in the respective chapters of this manual Overview of the selectable function settings Function Display text To enter and exit the c Settings mode Temperature unit F oC oF see Setting the temper
14. ship P Do not install the freezer in a room with too low an ambient temperature e g a garage as this may lead to the appliance switching off for longer periods so that it cannot maintain the required temperature P In appliances with an automatic ice maker avoid contact with the moving parts of the ejector mechanism or with the heating element located on the bottom of the ice maker Do not place fingers or hands on the automatic ice making mechanism while the freezer is plugged in P The ice cube maker is not suitable for connection to a hot water supply P Do not use water that is microbiologically or chemically unsafe or of unknown quality without adequate disinfection or other treatment before or after the filter is used the filter alone is not an adequate safeguard Use P This appliance is not designed for commercial use It is intended for use in domestic households and in similar working and residential environments such as shops offices and similar work environments by customers in hotels motels Bed amp Breakfasts or similar residential environments P This appliance is not intended for outdoor use P The appliance is only intended for residential use to store frozen foods freeze fresh foods and prepare ice All other uses are prohibited and may be dangerous IMPORTANT SAFETY INSTRUCTIONS P Persons who lack physical sensory or mental abilities or experience
15. the screws could penetrate risk of injury and damage 57 Installing the appliance In a cabinet without a back wall m Now attach the installation niche to the wall The built in cabinet must be secured to the wall behind it with several screws In a cabinet with a back wall m screw the cabinet to the wall behind it in several places using suitable mounting brackets For this use suitable plugs screws depending on the type of wall m screw the back wall of the cabinet in several places directly to the wall behind it For this use suitable plugs screws depending on the type of wall 58 Installing the appliance Securing an alternative anti tip device If the anti tip brackets cannot be attached securely an alternative anti tip device can be used Ensure that there is no give between the appliance and the anti tip device If possible always screw the wooden beam to existing studs Cut a wooden beam cross section min 3 x 4 75 mm x 100 mm to the required length The length is equal to the width of the installation niche If the installation niche is deeper than the appliance select a beam with a larger cross section or attach two beams The beam must cover the appliance by at least 2 50 8 mm m Mark the installation height lower edge of the beam on the rear wall of the niche m Select screws according to the thickness of the wo
16. time discard any ice cubes in the freezer empty the container and discard the ice production of the next 24 hours If the appliance or ice maker have not been routinely used for several weeks or months or if the ice cubes have an unpleasant odor change the water filter Water filter change indicator The change indicator will appear approx every 6 months depending on the quantity of ice produced filter When the filter indicator lights red this is an indication that a filter change will soon be necessary New water filters Bypass and Active charcoal filters are available from Miele m When the filter indicator flashes red in the display the filter must be changed Water filter Exchanging the water filter Note Air trapped in the system may cause water and the filter cartridge to eject forcefully Use caution when removing m Push in and rotate the filter cap on the base panel of your appliance counterclockwise 180 1 m Pull the used filter cartridge out of the appliance 2 m Remove the cap from the used filter 3 m Take a new filter cartridge out of the packaging and remove the protective cap m Push the cap onto the new filter cartridge 4 m Push the filter cartridge with cap in a horizontal position all the way into the opening in the base panel 5 m Rotate the filter cartridge clockwise 180 until the cap is in a horizontal position 6 31 Water filter
17. water filter See Water filter Ice is forming in the supply hose to the ice maker Check the water pressure The water pressure must be between 25 and 120 psi 1 72 8 25 bar Contact a plumber Check whether the freezer compartment temperature is too high See Selecting the correct temperature 41 After sales service In the event of a fault which you cannot easily fix yourself please contact the Miele Technical Service Department at the address on the back of this booklet When contacting the Technical Service department please quote the model and serial number of your appliance given on the data plate inside the appliance 42 MieleCare USA only MieleCare our Extended Service Contract program gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts Only genuine Miele parts installed by factory trained professionals can guarantee the safety reliability and longevity of your Miele appliance Please note that unless expressly approved in writing by the Miele Ser vice department Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele Our goal is to prevent unauthorized and untrained service personnel
18. 0 5 NTU 9542 516456 05 Particulate Class Particle size At least 10 000 gt 0 5 to lt 1um 5700000 particles ml 99 52 gt 85 69000 511079 03 Chlorine taste and odor 1 9 2 0 mg L 10 0 05 7 3 gt 50 96 84 511081 03 Based on the use of Cryptosporium parvum oocysts Application Guidelines Water Supply Parameters IMPORTANT Must be installed and operated Water pressure 30 120 psi 207 827 kPa in accordance with application guidelines Water temperature 33 F 100 F 0 6 C 38 C Failure to do so may void warranty Service flow 0 75 gpm 2 83 Ipm Change filter at least every 6 months Flush new cartridge for 3 minutes CAUTION To avoid property damage due to water For estimated costs of replacement leakage you MUST read and follow these operating elements please visit your local appliance instructions before installation and use of this dealer or parts distributor product WARNING Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the a N system Systems certified for cyst reduction may be e p used on disinfected waters that may contain filterable cysts a 3M company NSF is a registered trademark of NSF International CUNO Engineered Products Inc CUNO is a trademark of 3M Company used under license 1000 Apollo Road 2007 3M Company All rights reserved Eagan MN 55121 2240 U S A FAN 34 L
19. Miele Operating and Installation Instructions Freezer with Ice Maker F 1411 SF To prevent accidents en US CA and appliance damage read these instructions before installation or use M Nr 09 743 950 Contents IMPORTANT SAFETY INSTRUCTIONS 220020055 4 Guide to the freezer 6 0 0 tee 8 Before USC uoces deb Eee daw EI a ee EE ORO EO Ke 10 Turning the appliance On Off 0 0 0 0 estate e es a eia a 10 Settings seo oe een ee re dene id eee Vue ehe ms 11 USING tlie Settlgs 22d aser ce Free ette d dede os p i deme ae S 11 Additional geings 2e cer rhe ober sa ord Spore o eee bet doen 11 Turning the button sound On Off liliis eese 12 Turning off for longer periods of time iilii iliis 13 Temperature and door alarm Luise eee 14 Temperature danni veer dceE Sx dx er eee ae Cada Wd PENES 14 Beleg PL etn ace ght eG eM eae ety eee ate 14 Setting the temperature 0 000 000 eee 15 Using the freezer efficiently lille lesse 17 Freezing food s esegue RR Y 4x RE RTRERYePed d wee dE 17 DefroStlfiQs cct ov rIinPERX PEE uer bri yada e IET e d iud 18 Goolinig drinKS QUICK ons uae p E T Eee vad ve RS ERR e e ws 18 SuperCool suus issus osea d e a a Ede Ry ee es 20 Ice cube maker 1 0 0 0 0 eee ee 21 Automatic defrost lilii eile 22 Adjusting the interior fittings lille elles 23 Moving the SH6IVES casus RR EROR REG e
20. acity is used 24 hours are recommended This helps food to freeze quickly and retain its nutrients vitamins flavor and appearance Switching on SuperCool m Touch the SuperCool sensor so that it turns yellow The temperature now begins to fall with maximum cooling performance The new temperature setting appears in the display 22 F 30 C 20 Switching off SuperCool The SuperCool function automatically switches off after approx 52 hours The sensor button turns white and the appliance continues running at normal power To save energy you can switch off the SuperCool function once the food is sufficiently chilled m Touch the SuperCool sensor so that it turns white The temperature display returns to the original temperature setting The appliance now continues running at normal power Ice cube maker For the automatic ice cube maker to operate it must be connected to the household water supply See Plumbing Turning on the ice cube maker m Make sure that the ice cube container is under the ice cube maker as far as possible Ice cubes will not be produced unless the container is completely closed RA m Touch the sensor button for the ice cube maker so that it turns yellow As soon as the freezer has cooled to a freezing temperature the ice cube container fills with water Cold air is blown directly over the container As soon as the ice cubes are frozen they fall into the i
21. ation niche m Open the appliance doors m Fasten the appliance on the left and right hand sides with the 3 supplied wood screws If there is a fairly large gap above the appliance cut a wooden beam to fit exactly and place it in the gap Now connect the water supply to the appliance see Plumbing 62 Installing the appliance Attaching the toe kick cover The maximum height of the toe kick cover is 4 101 mm from the top of the floor Do not cover the ventilation slits in the plinth Risk of damage to the appliance m f required cut the toe kick cover to the required length and height m Remove the foil from the adhesive strips m Attach the toe kick cover to the plinth m Attach the plinth to the appliance m Put the included cover plates in place 63 Installing the appliance Mounting the air separator The air separator keeps the supply and exhaust air Separate This prevents warm exhaust air from flowing into the machine optimizing the energy performance of the unit gt e e Hle m f necessary shorten the three parts of the air separator m Insert the foam pieces back into the sides 64 m Position the air separator in the center of the appliance door m From below screw the air separator firmly onto the door with the 2 Screws Plumbing All plumbing work should be carried out by a s
22. ature RemoteVision r Module settings optional accessory Button sound on off b see Settings No function h Settings Turning the button sound On Off If you prefer the buttons to be silent when touched the button sound can be turned off m Touch the access button J so it turns yellow m Note the position of the V button but do not touch m Touch the access button J again so it turns white Only the access button J is visible m Place one finger on the position of the V button and hold the V button will not be visible 12 m While holding down the V button press the access button J once Keep holding the V button down until the following appears in the display approx 5 seconds v amp m Tap the V button until 6 appears in the display m Touch the access button J to confirm m By touching the V button you can choose between b U Button sound is off b 7 Button sound is on 5 Return to menu m Touch the access button J to confirm the setting m Tap the V button until you see c in the display m Touch the access button J You have now left the Custom settings mode When you are in the Custom settings mode the door alarm is turned off automatically Once the door is closed it is reactivated Settings Turning off for longer periods of time If the appliance is not going to be used for an extended time for example during a
23. ce cube container The ice cube maker can produce approx 120 ice cubes within 24 hours Note Ice production will vary due to your water supply temperature pressure and hardness The production volume of the ice depends on the temperature in the freezer The lower the temperature the more ice cubes produced After the appliance is turned on for the very first time it can take up to 10 hours for the first ice cubes to drop out of the ice cube maker and collect in the container Once the ice cube container is full the ice cube maker switches off automatically Do not use the ice cube container for rapid cooling of food or drinks The ice cube maker may become blocked and be damaged Do not use the first three containers of ice cubes from the ice cube maker Discard the ice produced in the first 24 hours after switching on the ice cube maker This applies for the very first use and whenever the appliance has been out of service for an extended period of time The amount of ice cubes produced depends on the temperature in the freezer section The lower the temperature the more ice cubes will be produced in a given period of time Turning off the ice cube maker The water supply line must be shut off several hours before the appliance or ice cube maker is switched off SS m Touch the sensor button for the ice cube maker so that it turns white 21 Automatic defrost The freezer defrosts automatically
24. ch to turn the appliance off completely The main switch is located on the right side underneath the control panel m Unplug the power cord m Remove any food from the appliance and store it in a cool place m Take out any removable parts e g shelves Cleaning the interior and accessories Use a mild solution of warm water and liquid dish soap Wash all accessories and drawers by hand Do not wash in a dishwasher m Clean the appliance as needed m After washing wipe down the interior and accessories with a clean wet cloth then dry with a soft cloth Leave the appliance door open for a short time so the moisture can evaporate 26 Appliance door m Stainless steel surfaces can be cleaned using a non abrasive stainless steel cleaner m To help prevent resoiling a conditioner for stainless steel can also be used Apply sparingly with even pressure Aluminum frames The shelf frames and the door baskets are made of aluminum m Clean the frames with a mild solution of warm water and liquid dish soap Aluminum is susceptible to scratches and nicks treat with care The aluminum frames may become discolored or otherwise altered if soiling is not cleaned away promptly Do not use stainless steel cleaners lime removers scouring pads such as pot scrubbers or used sponges that still contain abrasive cleanser residue to clean the frames Cleaning and care Ventilation slits m Check the ve
25. circuit breaker Upper lighting m Grasp the front of the light cover with both hands and slide it back m Carefully pull the cover forward and out Never touch a halogen bulb with bare fingers When inserting a glass halogen bulb always hold with a soft cloth 28 Cleaning and care Side lighting d N Y m Turn the light cover counterclockwise and pull out Never touch a halogen bulb with bare fingers When inserting a glass halogen bulb always hold with a soft cloth m Pull the defective light bulb from the socket m Place the new bulb in the socket Halogen bulb type 5 W 12 V socket G 4 m Put the light cover back on and turn clockwise into place m Restore power to the appliance 29 Water filter The appliance is supplied with an active charcoal filter which improves the taste and smell of ice cubes by removing chlorine and other substances from the incoming tap water Additional water filters are available from Miele It is important to change the water filter regularly To avoid serious illness or death do not use water that is microbiologically or chemically unsafe or of unknown quality without adequate disinfection or other treatment before or after use of a filter 30 Note After installing a new water filter and switching on the ice maker discard the first 24 hours worth of ice production If the ice maker has not been used for a prolonged
26. completely installed and secured as per the installation instructions Empty weight of your machine F1411SF 359 Ibs 163 kg Installation site The appliance should be installed in a dry well ventilated room Do not install the appliance outdoors in an environment with dripping water in rooms which are at risk of frost The installation location should not be exposed to direct sunlight nor near a heat source such as an oven radiator etc The ambient temperature should not drop below 55 F 13 C or rise above 110 F 43 C otherwise malfunctions may occur If installation next to a heat source is unavoidable observe the following minimum distances from the heat source 1 8 cm from an electric cooktop or electric oven 12 30 cm from a gas or oil cooktop range or oven The following should also be taken into consideration The electrical outlet must be easily accessible in case of an emergency not concealed behind the appliance The plug and cord must not touch the rear of the appliance as they could be damaged by vibrations from the appliance Do not plug in other devices behind this appliance 45 Installation Important When there is high humidity a build up of condensation on the outer surfaces of the appliance can occur This can cause the surfaces to corrode To prevent this it is advisable to install the appliance in a dry and or
27. ct router setup instructions are not included in this manual Wording and instructions may vary 69 RemoteVision optional accessory Accessing the RemoteVision control panel m Touch the access button J so it turns yellow m Note the position of the V button but do not touch m Touch the access button again so it turns white Only the access button is visible m Place one finger on the position of the V button and hold the V button will not be visible m While holding down the V button press the access button J once Keep holding the V button down until the following appears in the display approx 5 seconds v LL Access to the Custom settings mode is now active for approximately 10 seconds 70 m Tap the V button until appears in the display m Touch the access button J to confirm See the table on the following page for a description of each setting in the display m Use the A or V buttons to select the RemoteVision options The module has been connected to the network when r appears in the display If c does not appear refer to the Network options section of the XKM 2000 Installation Instruction manual m Press and hold the access button for 2 seconds to confirm the change m To return to the main menu tap the V button until a solid r appears in the display m Press the access button 8 to confirm m Tap the V button until a c appears in the
28. display m Touch the access button J You have left the Custom settings mode When you are in the Custom settings mode the door alarm is turned off automatically Once the door is closed it is reactivated RemoteVision optional accessory MasterCool control panel options for RemoteVision Status indicators Description of function Flashing r Module booting phase Flashing r Not connected to network Flashing r Connection to network established no IP address assigned Solid rz Connected to network Flashing r In Ad Hoc Mode not connected Flashing r In Ad Hoc Mode connected Selectable Description of function options re Back re Reboot the module r Reset to factory settings rH Enter Ad Hoc Mode Note If you cannot select any option other than r Back the module has not been installed correctly 71 Please have the model and serial number of your appliance available before contacting Technical Service U S A Miele Inc National Headquarters 9 Independence Way Princeton NJ 08540 Phone 800 843 7231 609 419 9898 Fax 609 419 4298 www mieleusa com Technical Service amp Support Nationwide Phone 800 999 1360 Fax 888 586 8056 TechnicalService mieleusa com Miele www miele shop com Canada Miele Limited Headquarters and Showroom 161 Four Valley Drive Vaughan ON L4K 4V8 Phone 800 643 5381 Fax 905 532
29. door has been closed properly A large amount of food is being frozen at the same time This makes the compressor run longer causing the temperature to fall automatically The freezer is too warm The room temperature is lower than the ambient temperature for which the appliance is designed Raise the temperature of the room Operating the appliance in a room that is too cold will cause the cooling system to switch off for too long causing the freezer section to become too warm 36 Frequently asked questions General problems Issue Possible fault Solution Water is flowing out of the appliance Close the shut off valve immediately Check whether the water pipe in the appliance is defective Contact Miele Technical Service Check whether the water pressure is too low Contact a plumber Check whether the correct water valve has been installed Self tapping valves and 3 16 4 76 mm saddle valves reduce the water pressure and can block the pipe The door to the freezer section will not open This is not a fault The suction caused by opening and closing the door too many times in succession prevents it from opening Wait a few minutes then try again It should now open without force The compressor kicks on very frequently and for too long The ventilation slits are covered or dusty Clean with a vacuum or brush
30. e appliance Mounting Accessories The mounting accessories needed for installing the appliance into the niche are included in the packaging Several plastic bags are included which are marked alphabetically The bag needed for each step will be marked with its respective letter Anti tip brackets The anti tip brackets D keep the appliance safely secured in the installation niche and prevent it from tipping x lt 0 4 lt 10mm NRisk of tipping The installation niche must be securely attached to the wall behind it This is the only way the appliance which is later secured in the niche can be prevented from tipping Two anti tip brackets are recommended for each appliance For side by side installations 4 brackets are recommended m Position the anti tip brackets on the left and right in the installation niche so that there is no more than 3 8 10 mm of space between the brackets and the side walls m Mark the drill holes in the anti tip brackets on the back wall and on the ceiling of the installation niche m Set the brackets aside they will be needed again later Screws are supplied with the appliance for various applications materials If the anti tip brackets cannot be attached securely with the screws supplied an alternative anti tip device can be used Ensure that there are no electrical wires or plumbing in the area which
31. e minimum thickness of the partition is 5 4 16 mm IAE ETE PP Eg If there is a partition with a thickness from 16 mm to 6 160 mm between the adjacent appliances then each appliance should be individually installed within its own niche using the mounting accessories included The Merging Kit will also be needed The Merging Kit is available from Miele Installation with partition without using the Merging Kit If there is a partition with a thickness of more than 6 5 46 160 mm between the adjacent appliances then each appliance should be individually installed within its own niche using the mounting accessories included the Merging Kit is not necessary Side panels If one side of the appliance is visible a side panel must be used The side panel must be firmly secured to the wall the floor and the overhead furniture fixtures before the appliance is placed in the cavity The dimensions of the side panel are taken from the opposite wall of the installation space During installation ensure that the cavity is square and the measurements are correct 49 Dimensions Niche dimensions ww vet Z u v8 18 457 mm 18 12 469 8 mm F 1411 SF 50 Dimensions Power supply and water connection 515 16 150 mm 1 Power supply 2 Water connection A F 1411 SF 9 229 mm Install a pressure limit
32. ead free certificate C USA This product F 1411 SF KIMSDF18US is tested and certified by WQA against ORDOY02 for California lead free compliance Miele amp Cie KG Carl Miele StraBe 29 D 33332 G tersloh 35 Frequently asked questions With the aid of the following guide minor problems can be corrected without a ser vice call Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations Unauthorized repairs could cause personal injury or machine damage and may void the warranty Problems with temperature Issue Possible fault Solution The freezer does not get cold The machine is not turned on Check whether the appliance is turned on at the main switch The temperature display must be lit up The machine is not plugged in Check that the plug is correctly inserted in the power outlet Check that the fuse has not tripped Reset the circuit breaker If the breaker trips again the appliance or the outlet may be defective Contact Miele or a qualified electrician The temperature is set incorrectly Check the display The temperature in the freezer is too low Select a warmer temperature See Selecting the correct temperature The SuperCool function is still on SuperCool automatically shuts off after 52 hours The door is not closed Check that the
33. eds to be changed See Exchanging the water filter 38 Frequently asked questions Problems with the ice maker Issue Possible fault Solution The ice cube maker will not switch on The appliance is not plugged in Check that the appliance is connected to the power supply The ice cube maker is not producing any ice cubes When the appliance is turned on for the very first time it can take up to 10 hours for the first ice cubes to drop out of the ice cube maker and collect in the container The appliance is not turned on Check that the appliance is switched on The water supply line was not primed purged of air before the appliance was used for the first time Contact Miele Check if the ice cube maker is switched on the water supply line is open there are ice cubes stuck together and blocking the exit the ice cube container is in the right position the freezer compartment temperature is too high the water pressure is too low The water pressure must be between 25 and 120 psi 1 72 8 25 bar See Ice Cube Maker and or Plumbing for more information Check whether the correct water valve has been installed Self tapping valves and 3 46 4 76 mm saddle valves reduce the water pressure and can block the pipe 39 Frequently asked questions Problems with the ice maker
34. from working on your Miele products possibly doing further damage to them you and or your home To learn more about MieleCare Extended Service Contracts please contact your appliance dealer or visit us online at hitp mieleusa com mielecare ser Installation Instructions Information is subject to change Please refer to our website to obtain the most current product specification technical amp warranty information To prevent accidents and machine damage read these instructions before installation or use Caring for the environment Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable Please recycle Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of babies and young children Danger of suffocation 44 Disposal of an old appliance Old appliances contain materials that can be recycled Please contact your local recycling center about the possibility of recycling these materials Before discarding an old appliance disconnect it from the electrical supply and cut off the power cord to prevent it from becoming a hazard Installation Have the appliance installed by a qualified technician according to the enclosed installation instructions WARNING This appliance is top heavy and must be secured to prevent it from tipping forward Keep the door closed until the appliance is
35. he 0 6 eee 56 Sliding the appliance into the installation niche ilis 60 Aligning the applianee a ust e hcm oer Re es Pee bbe 61 Attaching the appliance to the installation niche liliis 62 Plu rdbing see Asse ydp a oP REL Y aed ewe a 65 Electrical connection iiie ees 68 RemoteVision optional accessory 0 a 69 IMPORTANT SAFETY INSTRUCTIONS When using the appliance follow basic safety precautions including the following Read all instructions before installation and use to prevent accidents and machine damage This appliance is intended for residential use only Use only as described in this Operating manual Only use the appliance for its intended purpose This appliance complies with current safety requirements Improper use of the appliance can lead to personal injury and material damage Keep these operating instructions in a safe place and pass them on to any future user Electrical Safety P Before installation make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply This data must correspond to prevent injury and machine damage Consult a qualified electrician if in doubt P Before installation or service disconnect the power supply to the work area by unplugging the unit tripping the circuit breaker or removing the fuse P Do not use an extension cord to connect this a
36. he connection for the shut off valve and to the appliance m Turn the appliance on After a maximum of 10 hours the first ice cubes will drop out of the ice cube maker and collect in the ice cube container 67 Electrical connection VAN Avoid the risk of electrical shock Plug into a grounded 3 prong outlet Do not move the ground plug Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock Improper connection of the equipment grounding conductor may result in electric shock If you are in any doubt as to whether the appliance has been properly grounded have the appliance checked by a qualified electrician or service technician Installation repairs and other work by unqualified persons could be dangerous Before installing the appliance verify that the voltage load and circuit rating information found on the data plate match the household electrical supply If there are any questions regarding the electrical connection of this appliance to the power supply please consult a licensed electrician or call the Miele Technical Service 053 1 800 999 1360 CDN 1 800 565 6435 68 The appliance is supplied with a UL listed 3 wire power cord and NEMA 5 15 P plug ready for connection to a 120 V 60 Hz supply The fuse rating is 15 amps The appliance requires a 3 wire receptacle The receptacle must be in
37. iance to drop to the coldest temperature If the room temperature is too high it may not be possible for the appliance to reach the lowest temperature Setting the temperature Temperature unit Fahrenheit Celsius The temperature can be displayed in degrees Fahrenheit F or Celsius C be m Touch the access button J so it turns yellow m Note the position of the V button but do not touch m Touch the access button J again so it turns white Only the access button is visible m Place one finger on the position of the V button and hold the V button will not be visible 16 m While holding down the V button press the access button J once Keep holding the V button down until the following appears in the display approx 5 seconds v LL m Tap the V button until appears in the display m Touch the access button J to confirm m By touching the V button you can select either Fahrenheit or Celsius for the temperature display B Fahrenheit 1 Celsius return to menu m Touch the access button J to confirm the setting m Tap the V button until a c appears in the display m Touch the access button J You have left the Custom settings mode When you are in the Custom settings mode the door alarm is turned off automatically Once the door is closed it is reactivated Using the freezer efficiently Freezing food Fresh food should be frozen as
38. ing device and water hammer arrester for inlet water pressures exceeding 80 psi Refer to Uniform Plumbing Code Sections 608 2 and 609 10 Never install or operate where inlet water pressure may exceed 120 psi 51 Dimensions Door dimensions open 115 Miele recommends using the full door opening angle of 115 for this freezer B f un We m idi A B F 1411 SF 2p Rr 935 525 mm 234 mm 52 Installing the appliance Before you begin Read these instructions completely and carefully Have the appliance installed by a qualified technician according to the enclosed installation instructions To reduce the risk of injury or damage to the product two people should be used for installation These installation instructions are intended for use by qualified installers In addition to these instructions the appliance must be installed in accordance with all local codes In the absence of a local code the following should be used Inthe USA the National Electric Code ANSI NFPA 70 latest edition State and Municipal codes and or local codes n Canada the Canadian Electric code C22 1 latest edition Provincial and Municipal codes and or local codes Tools needed for installation Cutter with adjustable blade Cordless screwdriver T 20 Torx screwdriver T 20 Hammer drill for drilling holes in wall or floor Wood drills in different sizes
39. nsions The side walls of the installation cavity must be plumb The minimum thickness of the side walls and the top wall must be 5 16 mm The minimum thickness of the toe kick panel must be 1 2 13 mm A thickness of 3 4 19 mm is recommended 47 Installation Stainless steel panels Stainless steel door panels and toe kick covers are available from Miele Installation options There are many different installation options You are limited only by the design of the kitchen The door hinge cannot be exchanged Single column The appliance can be installed at any preferred location in the kitchen However be sure the door will open and close properly in the chosen location 48 Side by side This appliance can be installed side by side with another fridge freezer using a Merging Kit The Merging Kit is available from Miele Contact Miele or your dealer for specific information about which combinations will work with your appliance For instructions on how to attach the appliances and install the heating mat please refer to the instructions included with the Merging Kit available from Miele Installation without a partition using the Merging Kit If the appliances are installed directly next to each other without a partition they need to be attached together using the Merging Kit Installation Installation with partition using the Merging Kit Th
40. ntilation slits in the base panel regularly Remove any dirt dust with a vacuum cleaner or brush Clean as needed Door seals Do not use any oils or grease on the door seals This may cause the seals to deteriorate and become porous over time m Clean the door seals with warm water and dry with a soft cloth After cleaning m Return all shelves and accessories m Shut the appliance door plug in the appliance and turn it on with the main Switch m Turn on the SuperCool function The freezer section will cool down quickly m Once the temperature is cold enough place the freezer baskets containing the frozen food into the freezer m Turn off the SuperCool function on a temperature of O F 18 C is reached 27 Cleaning and care Changing the light bulb The lighting automatically switches off after the door has been open for approx 5 minutes This is not a fault After the bulb has cooled for a short time it will turn on again If the light does not come on when the door is opened briefly the light bulb should be changed m Remove the defective light bulb m Use the main switch to turn the m Place the new bulb in the socket appliance off Halogen bulb type 20 W 12 V socket GY 6 35 m Slip the rear of the light cover back into position then pull it forward and into place To reduce the risk of electric shock disconnect the appliance from the power supply by unplugging or tripping the
41. oden beam Example 3 1 2 screw for 2x4 beam Determine the number of screws based on the niche width to ensure that the beam will be attached securely m Locate wall studs near the rear wall of the cavity and mark drill holes in the beam m Pre drill the wooden beam m Attach the wooden beam to the rear wall of the niche Now prepare the water connection from the appliance to the main supply line see Plumbing 59 Installing the appliance Sliding the appliance into the installation niche If a side by side installation is desired connect the two appliances together See the Installation Manual included with the Merging Kit m To protect the corners of the installation space attach edge protectors where needed not included 60 m Plug the appliance into the power outlet CD The plug of the appliance should be easily accessible after installation If the plug is not accessible after the appliance has been installed disconnection from the power supply should be completed via the circuit breaker In the case of side by side installations a separate outlet must be used for each appliance m To prevent the power cord from becoming caught Tie a piece of string to the middle of the power cord and feed it forward under the appliance When sliding the appliance in pull the cable forward m Carefully slide the appliance into the space If resistance is felt when at
42. ppliance to electricity Extension cords do not guarantee the required safety of the appliance e g danger of overheating P Be certain your appliance is properly installed and grounded by a qualified technician To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding System It is imperative that this basic safety requirement be met If there is any doubt have the electrical system of the house checked by a qualified electrician P Only connect power to the appliance when all installation and plumbing work is complete IMPORTANT SAFETY INSTRUCTIONS Installation This appliance is top heavy and must be secured to prevent the possibility of tipping forward Keep the door closed until the appliance is completely installed and secured per installation instructions P This appliance must be installed and connected in compliance with the installation instructions P Installation and repair work should be performed by a Miele authorized service technician Work by unqualified persons could be dangerous and may void the warranty P Installation must comply with local plumbing regulations and state laws P Do not operate any appliance with a damaged cord or plug or if the appliance has been damaged in any manner Contact Miele s Technical Ser vice Department P This appliance must not be used in a non stationary location e g on a
43. pply by shutting off the power main tripping the circuit breaker or unplugging the power cord before maintenance Never use cleaning agents containing abrasive substances such as sand soda acids chlorides or chemical solvents Non abrasive cleaning agents are also unsuitable as they can cause matte areas to appear Stainless steel surfaces can be cleaned using a non abrasive stainless steel cleaner available from Miele Only use a mild solution of warm water and liquid dish soap to clean this appliance Do not use a steam cleaner to clean this appliance Pressurized steam could penetrate electrical components and cause a short circuit Do not allow water to get into the electronic unit or lights The data plate located inside the appliance must not be removed It contains information which is required in the event of a service call To better maintain your appliance avoid the following cleaners containing soda ammonia thinners or chlorides cleaners containing descaling agents or lime removers abrasive cleaners dishwasher soap powder caustic oven cleaners scouring pads steel wool hard brushes metal scrapers eraser sponges steam cleaning products Glass cleaners may be used to clean the exterior However do not allow them to sit or puddle this can cause damage to the surface Remove the cleaner promptly 25 Cleaning and care Before cleaning m Use the main swit
44. quickly as possible This helps maintain the nutritional value vitamin content appearance and taste of the food Never refreeze partially or fully defrosted food Consume defrosted food as soon as possible it will lose its nutritional value and spoil if left for too long Do not refreeze defrosted food unless it has been cooked Before placing food in the freezer m When you are planning to freeze large amounts of food more than 4 1 Ibs 2 kg switch on the SuperCool function ahead of time see SuperCool This will provide the food already in the freezer with a protective boost of cold air Placing food in the freezer Food to be frozen can be placed anywhere in the freezer The freezer baskets can hold a maximum of 35 Ibs 16 kg of frozen food m Spread the food to be frozen across the bottom of the freezer basket or across the shelves so that it will freeze through to the core as quickly as possible m When placing items in the freezer make sure the packaging and containers are dry to keep them from sticking together when frozen When freezing try not to let frozen food come into contact with unfrozen food this could cause the frozen food to defrost Using the freezer efficiently Defrosting Cooling drinks quickly Frozen food can be defrosted in To cool drinks quickly switch on the different ways SuperCool function See SuperCool for more information in a microwave oven Do no
45. r baskets For easier loading unloading and cleaning the freezer baskets can be shifted or completely removed m Pull the basket forward until resistance is felt On the hingea side of the door is a safety lock which must be turned to a horizontal position before the drawer can be removed m Using a suitable object e g coin turn the safety lock to a horizontal position m On both sides of the basket pull the latches 2 upward and lift the basket out of the freezer Replacing the freezer basket m Fully extend the telescopic tracks m Lay the basket onto the tracks so that it connects in the front and back m Turn the safety lock back to the vertical position m Slide the freezer basket in 23 Adjusting the interior fittings Ice cube container The ice cube container is set on telescopic tracks and can be removed for loading unloading and cleaning m Slide the container forward until resistance is felt m On both sides of the container pull the latches see arrow upward and lift the container out of the freezer Push the tracks back into the freezer to avoid injury Replacing the ice cube container m Completely extend the telescopic tracks m Lay the container onto the tracks so that it connects in the front and back m Slide the ice cube container completely in 24 Cleaning and care To reduce the risk of electrical shock disconnect the appliance from the power su
46. stalled by a licensed electrician only In the case of side by side installations a separate outlet must be used for each appliance Ideally the power outlet should be next to the appliance and easily accessible Do not connect the appliance to the power supply by an extension cord Extension cords do not guarantee the required safety of the appliance danger of overheating If any changes are needed to the household wiring or power supply this work must be performed by a qualified electrician RemoteVision optional accessory Miele s RemoteVision Wi Fi technology creates a virtual link between your appliance and our monitoring center If a fault occurs Miele s client service center will be notified and contact you or another trusted individual identified on your call roster in order to gain access to your appliance to fix the problem For information on set up and installation of the RemoteVision module see the Installation section of this manual Be sure your wireless system meets the following requirements A wireless router that supports an IEEE 802 11b protocol Windows XP or newer operating system Mac OS X 10 3 or higher Cable or DSL modem Microsoft Internet Explorer 6 or higher Safari 2 0 or higher Firefox 1 5 or higher Please note that each wireless router manufacturer supplies their own device drivers and setup programs Due to the differences in manufacturers exa
47. t m Check the location of the water connection see Plumbing m Check that all furniture parts in the vicinity of the appliance are securely connected to the wall m Check that the adjacent furniture fixtures do not collide with the open door Before installation Caution the appliance is very heavy Use caution when unpacking and opening the door danger of tipping m To protect the base from damage during installation attach a hard board linoleum etc to the floor in front of the intended installation location m Take the supplied accessories out of the protective packaging Installing the appliance There are transportation safety devices inside the appliance to protect the shelves and storage compartments until installation is complete Do not remove them or parts may be damaged m Check the appliance for damage in transit Do not install the appliance if it is visibly damaged If in doubt contact your dealer 99 4 m Loosen the bracket that holds the appliance to the pallet N Caution The appliance is no longer secured and may be unstable m From the rear of the appliance carefully lift it from the pallet Once the appliance is on the ground it can be wheeled around RemoteVision module installation optional accessory Always disconnect the appliance from the power supply when performing installation maintenance or service work Install the RemoteVision module
48. t m To turn the alarm off early press the alarm sensor button The alarm signal turns off The alarm indicator remains on until the alarm condition is corrected If the temperature in the freezer zone reaches O F 18 C or higher check that food has not defrosted Door alarm If the appliance door is left open an alarm signal will sound and the alarm indicator will turn red after five minutes Once the door is closed the alarm will turn off and the alarm indicator will go Out Turning the door alarm Off To turn the alarm off early m The alarm indicator and signal will turn off The alarm will turn off and the alarm indicator will go out Setting the temperature Setting the temperature be m Touch the access button J so it turns yellow I v oto m Use the V and buttons next to the temperature display to set the temperature warmer or colder Tap the V and sensor buttons to raise lower the temperature 1 or hold it down to move through the temperature range more quickly The temperature display on the control panel always shows the desired temperature Temperature range The temperature can be set within the following range 7 F to 11 F 14 C to 24 C To freeze fresh food and store frozen food for an extended period of time a temperature of O F 18 C is suggested The room temperature and the installation location can affect the time it takes for the appl
49. t leave bottles in the freezer for more than 1 hour closed containers in the refrigerator the cold given off could burst by the frozen food helps to keep the other food cold atroom temperature in a steam oven Poultry It is especially important to observe proper hygiene when defrosting poultry Never save the liquid from defrosted poultry Drain it away and promptly wash the container the sink and your hands Danger of salmonella poisoning Fruit should be defrosted at room temperature in its packaging or in a covered bowl Most vegetables can be cooked while still frozen Simply place directly into boiling water or hot oil 18 Using the freezer efficiently Freezing tips The following are examples of foods suitable for freezing Fresh meat poultry game fish vegetables herbs fresh fruit pastry dough leftovers and a range of pre cooked meals The following examples of foods not suitable for freezing Lettuce radishes sour cream mayonnaise eggs in their shells onions whole raw apples and pears To retain color taste and vitamin C vegetables should be trimmed washed and blanched To blanch bring a large saucepan of water to a boil then submerge the vegetables in rapidly boiling water for 2 3 minutes depending on type Remove and plunge into ice cold water to cool quickly Drain and pack for freezing Lean meat freezes better than fatty meat and can be s
50. tempting to slide the appliance into the installation niche for example because the floor is uneven m Turn the rear adjustable wheels slightly outward see Aligning the appliance then push the appliance in Be careful not to damage the water pipe or power cord attached to the floor m Remove the edge protectors Installing the appliance Aligning the appliance m Align the appliance with the surrounding cabinets Ss a 1 1 4 32mm The height adjustable feet at the front and rear can all be adjusted from the front Front feet Adjust with a rachet 5 16 8 mm 9 Rear feet Adjust with a cordless screwdriver and or a rachet 5 16 8 mm for fine adjustment Important When unscrewing the height adjustable feet proceed gradually alternating between left and right m Unscrew the height adjustable feet until the mark on the base has reached the indicated guide dimension 1 1 4 32 mm The guide dimension of 1 1 4 32 mm is related to a niche height of 84 2134 mm Important The height adjustable feet can only be unscrewed as far as the 2 3 16 62 mm mark on the base max niche height of 85 3 16 2164 mm m Align the appliance again using a level m f using a wooden beam as an alternative anti tip device rotate the appliance all the way toward the wooden beam 61 Installing the appliance Attaching the appliance to the install
51. tored for considerably longer To prevent chops steaks cutlets or rolled meats from freezing together in solid blocks when packed separate with a sheet of plastic freezer wrap Do not season fresh foods or blanched vegetables before freezing Cooked food can be lightly seasoned before freezing but care should be taken as the taste of some spices alters when frozen Do not place hot foods or drinks in the freezer This causes already frozen food to thaw and increases the energy consumption considerably Allow hot foods and drinks to cool down before placing them in the freezer Packing tips m Unsuitable packing material wrapping paper greaseproof paper cellophane garbage bags plastic shopping bags Suitable packing material plastic freezer bags wrap aluminum foil freezer containers m To help prevent freezer burn expel as much air as possible from bags etc before sealing them m Close the packaging tightly with plastic clips twist ties rubber bands m Mark the package to indicate the contents and the date of freezing SuperCool When the SuperCool function is activated the appliance is cooled as cold as possible to a factory preset temperature SuperCool The SuperCool function is ideal for freezing large quantities of unfrozen food Ideally the function should be switched on 4 6 hours before the food is placed in the freezer If the max freezing cap
52. ube maker m position the device in front of the installation kit niche and push the stainless steel tube through the hose guide at the back of the unit m install the connecting pipe Always observe the indicated clearance dimensions to prevent damage to the At this point the niche should be ready connecting pipe when pushing in the for the appliance to be pushed back appliance into it see Installing the appliance m You can now continue with the installation m Secure the connecting pipe to the floor with adhesive tape m You may now proceed to install the appliance See Installing the appliance 66 Plumbing Connecting the water supply When connecting the water pipe to the solenoid valve of the appliance follow the instructions supplied by the manufacturer of the ice cube maker installation kit When bending the water pipe be sure not to kink it otherwise there is a risk of leaks and water damage Use bending aids m Remove the cap from the appliance connection 1 m Bend the water pipe to suit the location of the connection on the appliance 2 m Push the union nut and seal onto the water pipe m Push the end of the water pipe into the appliance connection and screw on the union nut 3 First tighten by hand m hen use an open ended wrench to tighten the union nut Do not over tighten m Open the shut off valve and the main water connection Check for leaks at t
53. uitably qualified and competent person in accordance with all applicable local and national regulations Disconnect the appliance from the electrical power supply before connecting it to the water supply Turn off the water supply before connecting the water lines to the ice cube maker The water quality must conform to country requirements for drinking water The appliance is only suitable for connection to the cold water supply The water pressure must be between 25 and 120 psi 1 72 8 25 bar A separate shut off valve must be installed so that the water supply can be interrupted as needed The maximum outer diameter of the water pipe without fittings 3 3 10 mm The shut off valve for the water connection must not be located behind the appliance It is recommended to place the shut off valve directly next to the appliance base unit or in another easily accessible location Do not use pipe extenders In the event that the piping has to be replaced only Original Miele Spare parts are suitable for use Contact Miele 65 Plumbing Preparing the water connection For appliances with a hose guide The connection to the household water supply must be installed before the appliance is installed m Turn off the main water valve to prevent damage caused by leaking water m Attach the connecting pipe to the shut off valve according to the instructions supplied by the manufacturer of the ice c
54. vacation some precautions need to be taken m Shut off the water supply line several hours before switching off the appliance m Take all food out of the appliance m Turn the appliance off m Unplug the appliance m Empty the ice cube container m Clean the interior m Remove and discard the water filter secure the filter cap m Leave the door open to prevent odors Temperature and door alarm The appliance is equipped with an alarm system to ensure that the temperature does not rise unnoticed because of energy loss or an open door The alarm system is always operational it does not need to be switched on Temperature alarm If the temperature becomes too warm an alarm sounds and the alarm indicator turns red and flashes and the temperature flashes in the control panel The temperature display shows the highest temperature reached during the alarm The alarm will sound and the display will flash if too much warm air flows into the appliance for example when food is being loaded re arranged or taken out large amounts of food are being frozen at once the power fails As soon as the alarm condition is corrected the alarm with turn off and the sensor button for alarm will go out 14 Turning the temperature alarm Off As soon as the alarm condition is corrected the alarm signal turns off and the affected zone stops flashing in the display The alarm indicator goes Ou
55. with the machine should not use it without supervision or instruction by a responsible person P To reduce the risk of injury do not allow children to play in on or near the appliance especially in the door hinge area P After your freezer is in operation do not touch the cold surfaces in the freezer compartment particularly when hands are damp or wet Skin may adhere to these extremely cold surfaces P Do not refreeze frozen foods which have thawed completely P Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance P Do not deactivate the water filter display P Do not use sharp edged objects to remove frost and ice or separate frozen foods and remove ice trays They will damage the evaporator causing irreversible damage to the appliance P Do not use defrosting sprays or de icers as they might contain substances which could damage the plastic parts or which could cause a build up of gases and pose a danger to health P Do not use any oils or grease on the door seal as these will cause the seal to deteriorate and become porous with time P Do not block the ventilation gaps in the plinth or the top of the appliance housing unit as this can impair the efficiency of the appliance increase the electricity consumption and cause damage to the appliance P Never use a steam cleaner to clean the appliance Pressurized steam could
Download Pdf Manuals
Related Search