Home

Miele CVA 4066 User's Manual

1. The water tank is not inserted properly Take it out and reinsert correctly The water tank was not filled correctly during the descaling process Fill the water tank up to the correct mark f the message still appears contact Technical Service The message Check water inlet appears Possible fault Solution The plumbed water intake is faulty Check for kinks in the water intake hose and open the water supply all the way Slide the water tank back in to the appliance f the fault is displayed again call Technical Service The gasket of the coffee dispenser connector is damaged and leaking Possible fault Solution The gasket is worn Check the door Is the alignment off from damage to the gasket Change the gasket with a new one supplied Adjust the door hinges See Installation Adjusting the door hinges Too much crema has formed and is above the coffee dispensers Possible fault Solution Some coffee types produce too much crema when the coffee espresso temperature is set to the maximum and the amount of ground coffee is too much Lower the temperature and amount of coffee 62 Frequently asked questions Possible fault Solution Replace the cap with the spare part Lubricate the cap of the main supplied dispenser with the supplied silicone grease Close the unit and prepare a coffee
2. m Lubricate the cap once a month with the supplied food grade silicone lubricant Interior and door m Once all movable parts are removed clean the interior with a solution of hot water and liquid dish soap Dry ground coffee can be vacuumed m The lower part of the inner door has a drip tray Clean the drip tray 49 Cleaning and care Brew unit Manually clean the brew unit weekly The movable parts are lubricated and the gaskets will get damaged in the dishwasher Do not use a dishwasher this will cause damage m Take out the water tank waste unit and the storage drawer m Press the light colored button on the brew unit handle CD and turn the handle to the left m Press the brew unit catch downwards and carefully pull the brew unit out The brew unit is not in the correct position if it is hard to pull out See Frequently asked questions m Clean the brew unit under running warm water Do not use soap Leave the handle in position or the brew unit cannot be inserted properly 50 m Rub off any coffee residue from the filters with a sponge One filter is in the funnel CD the second is to the left of the funnel m Dry the funnel D to prevent ground coffee from sticking m Clean the interior and remove coffee residues Dry coffee grounds can be vacuumed m Push the brew unit in the track straight into the appliance m Press the light colored button
3. Settings Amount of coffee The amount of coffee will determine both the strength and the crema of your brewed coffee Depending on the type of coffee the ideal amount ranges from approximately 0 2 ounces and 0 5 ounces 6 g to 14 g per cup The higher the value the stronger the prepared espresso coffee latte macchiato or cappuccino will be The crema is also influenced by the amount of coffee If the crema has an even but white yellow coloring the ground amount might be too little Ifthe crema is dark brown to black in color on the one side and almost white on the other side the amount of coffee might be too much m Using or select Settings h and confirm with OK Settings Amount af coffee Pre brewing m Tap or gt until Amount of coffee is highlighted confirm with OK m Use or to select a beverage confirm with OK m Using or adjust the amount of coffee to more or less m To save the setting tap OK 26 Pre brewing During the pre brew step the freshly ground coffee is first moistened with hot water After a short steeping period the remaining water is then forced through the moistened coffee at high pressure This process produces a much more intense coffee aroma If the function is turned off the hot water will be immediately pushed at a high pressure through the ground coffee You can program normal or long pre brew or turn the pre brew
4. All settings restores all settings back to the factory default m Under All settings select Reset confirm with OK All settings are now reset to the default Factory default settings Amount of coffee medium Temperatures for coffee beverages and hot water medium for both Pre brewing without Automatic rinse and steam system both On Showroom program Off Time display On for 60 seconds Time format 24 h Timer Switch on at 12 00 Timer Switch off after 1 00 Timer Switch off at 12 00 Switch on at and Switch off at both deactivated Coffee jug 3 cups Lighting Brightness medium Safety System lock Off Water hardness very hard 4 Display Contrast medium Brightness maximum Volume Buzzer tones and keypad tone both at maximum setting User profile Revert when machine is turned on Plumbed water supply On If Reset is selected by accident turn the machine off before pressing OK the settings will not be reset 33 Setting the serving sizes The flavor of a coffee beverage depends not only on the type of coffee but also on the quantity of water used Not every espresso or cappuccino cup is the same size Use this feature to set the volume of water to suit your taste and cup sizes For beverages with milk the proportions of espresso milk and froth have an important impact on flavor You can
5. gt until System lock is highlighted confirm with OK m Use lt or gt to select On confirm with OK As soon as the machine is turned off it will lock and cannot be turned back on A closed padlock v and a message will appear in the display whenever a button is touched To deactivate the system lock follow the same procedure as above but select Off Overriding the system lock m Press and hold OK for approx 3 seconds The machine is now temporarily unlocked and can be used to prepare beverages It will lock again as soon as it is turned off 30 Water hardness The hardness of the water used in the coffee system must be determined and programmed into the appliance The water hardness will determine how frequently the unit must be descaled to maintain the coffee system properly The machine monitors the volume of water used including the amount required for producing steam and will then let you know when a descaling cycle is necessary To measure the hardness of your water use the test strip that is included in your installation kit m Place the test strip under your kitchen tap for a second and shake off any remaining water The result is visible in about 1 minute If the water hardness is greater than 40 gr gal 40 D the water must be descaled more often than displayed Calcium will build up faster than at a lower water hardness and may damage the machine Settings You can p
6. or to select the user profile you wish to delete confirm with OK A check mark appears after the user profile and it will be erased shortly Revert The appliance can be set so that it automatically reverts to the standard user profile or continues to use the most recently selected user profile set m Use lt or gt to select Revert You can now choose between Manually The appliance retains the selected user profile until another profile is selected m Use lt or gt to select Manually confirm with OK After dispensing After each drink prepared the appliance automatically reverts back to the standard user profile m Use lt or gt to select After each use confirm with OK When switched on Each time the appliance is turned on the standard user profile will automatically be selected no matter which user profile was set before it was last turned off m Use or gt to select When switched on confirm with OK 39 Cleaning and care Quick Guide The coffee machine must be cleaned regularly to prevent bacteria Recommended frequency Every time milk is prepared if there is more than one hour between uses What needs to be done Rinse the milk pipework Every day at least at the end of the day before you switch off the appliance nse the system intake lines ean the milk lines with cleaning powder ean the stainless steel milk container and l
7. with a check To return to the previous options in the manu select Back The possible setting options are described in detail on the following pages 22 Language You can select the language for all text and messages displayed on your machine m Select Settings n and confirm with OK Settings Language F Time m Tap OK m Tap lt or gt until the language you wish to select is highlighted m Confirm with OK This setting is automatically saved and the display returns to the previous Screen All display text will now appear in the language selected If you select the wrong language accidently follow the flag icons to find the Language option Settings Time of day m Select Settings pe confirm with OK Settings Time of daw Timer m Tap lt or gt until Time of day is highlighted confirm with OK Three options are now available Display The time display can be turned on or off m Use lt or gt to select Display You can now choose from among three settings On The time will be displayed even when the machine is turned off On for 60 seconds The time will be displayed for 60 seconds after the machine has been turned off Do not display The display will go dark as soon as the machine is turned off m Once a display format has been selected confirm the setting with OK Clock format m Use or to select Clock format m
8. Tap lt or gt to select a 24 hour or 12 hour display m While the desired options is highlighted confirm with OK The clock format is now saved Setting the time of day m Use lt or gt to select Set m Tap lt or gt to set the hours Confirm with OK Repeat to set the minutes The time of day is now saved You can also set the time of day and change the display options when the coffee machine is turned off While the machine is off m Select the OK button m Select the Time of day and confirm with OK You can now select Display or Settings and set or change as desired m Confirm with the OK button to save the setting 23 Settings Timer m Select Settings pe confirm with OK m Select lt or gt until Timer is highlighted confirm with OK m Use lt or gt to select Set confirm with OK Three options are now available Switch on at You can program your machine to turn on automatically at a certain time for example at breakfast time m Tap lt or gt to select Switch on at confirm with OK m Tap lt or gt to set the hours Confirm with OK Repeat to set the minutes The machine will turn on each day at the specified time once you have activated the timer see Activate If the machine is turned on automatically three times and no beverages were dispensed the machine will no longer turn on automatically The programmed times stay saved and will
9. appliance iisiii eei ie 53 Frequently asked questions 0 a 55 After sales service liil illl ees 66 Installation instructions iillsllee leise 67 Caring for the environment lliiills i ls less 68 PIUMBING ieres taieri vada y EE de EG eke een de ee bY CR Re REA X em Ed 69 Electrical connection 0 0 0000 70 Installation oes 04 oeri dbo nd Ob 4 Robb Gert RES be bd hed eds 71 Adjusting the door NINGES ss sse as sen mede e kx e tana e ae eae an 73 IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances basic safety precautions should always be followed including the following Read all instructions before installation or use of the coffee system Please read these instructions carefully to prevent accidents and machine damage This appliance complies with current safety requirements Improper use of the appliance can cause personal injury and material damage Read this safety information carefully before operating the appliance They contain important information on the safe installation operation and care of your coffee system To avoid the risk of personal injury or damage to the coffee system it is important that you carefully read the instructions Keep them in a safe place and pass them on to any future user Proper use P This coffee system is for household use only up to 20 cups per day for the preparation of coffee beverages such
10. as espresso cappuccino latte macchiato etc Do not use this machine other than for its intended use Any other use could be hazardous P This coffee system is not suitable for outdoor use P Persons which lack physical sensory or mental abilities or experience with the machine should not use it without supervision or instruction by a responsible person Children P Close supervision is necessary when any appliance is used by or near children They could easily be scalded or burned P Never let children play with the coffee system P Install the appliance in an area where it will not be accessible to children IMPORTANT SAFETY INSTRUCTIONS Technical safety P Before installing the appliance check for externally visible damage Do not operate a damaged appliance P Before connecting the appliance to the electrical supply make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply If in doubt consult a qualified technician P Be certain your appliance is properly installed and grounded by a qualified technician To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding System It is imperative that this basic safety requirement be met If there is any doubt have the electrical system of the house checked by a qualified electrician P The appliance must be properly
11. coffee m Tap or gt until Prog the amount is highlighted confirm with OK m Use or to select the beverage you wish to set a serving size for m Select Start confirm with OK Proceed as you would for programming using OK or B User profiles If the appliance is used by several people with different preferences you can save up to 9 individual user profiles The following settings can be programmed for each user profile Serving size for coffee beverages and hot water Serving size of milk for beverages with milk Amount of coffee Water temperature Pre brew See Setting the serving sizes and Settings User profile m Tap or gt until User profile is highlighted confirm with OK You can now either Select user profile from the profiles already set Create user profile to enter a new user profile The following options appear only if you have already created a user profile Change user profile to change a user profile Delete user profile to delete a user profile Revert The appliance can be set so that it automatically reverts to the Standard user profile or continues to use the most recently selected user profile set Selecting a user profile m Use or to select the user profile you wish to use confirm with OK Espresso John To show that a user has been selected the upper display line shows a lar
12. flow stops automatically The maximum amount is saved Fill the water tank or milk container before programming the serving size Water is in the waste unit Possible fault Solution This is not a fault This is residual water from the cleaning process Coffee water is in the waste unit Possible fault Solution f the grind setting is too coarse this can result in too much coffee water in the waste unit The main dispenser cap is not positioned correctly Adjust the grind setting and or amount of coffee Lubricate the cap with the supplied silicone grease If the cap is faulty replace it with the spare part supplied The descaling process was started accidently See Descaling The descaling process cannot be canceled once it is started The process needs now to be completed This is a safety feature to ensure the process will be completed It is important for best results and the longevity of the machine The machine makes loud noises during descaling During a descaling cycle the machine is relatively loud because water is being forced through the lines at high pressure This is not a fault 60 Frequently asked questions The preheating time is increased the water flow amount is not correct and the unit performs less Possible fault Solution The machine needs to be descaled See Descaling the app
13. installed before operation to ensure that no electrical components are accessible Ensure that power is not supplied to the appliance while installation work repairs or maintenance is performed P Do not use an extension cord to connect the appliance to electricity Extension cords do not guarantee the required safety of the appliance danger of overheating and open ground circuit P If the appliance is installed behind a door front use the appliance only when the door front is open Do not close the door front when the appliance is in operation P Before service or maintenance disconnect the power supply by either removing the fuse tripping the circuit breaker or unplugging the unit P This appliance is not designed for maritime use or for use in mobile installations such as recreational vehicles or aircraft However under certain conditions it may be possible for installation in these applications Please contact the Miele Technical Service Department with specific requirements P The unit is designed for a cold water connection Do not connect it to hot water it will get damaged P The water supply must be accessible after installation P Do not damage or kink the cover of the water intake hose P The waterproof system will only work if itis installed correctly itis damaged the machine repaired or faulty parts replaced the water supply is shut off when not using the coffee sys
14. into m After cleaning the nozzles of the main dispenser slide them back into the machine firmly upward to ensure they are securely in place m Replace the cover and slide the main dispenser up Cleaning and care Water tank Empty the water tank daily and refill before preparing the first drink with fresh cold tap water Check if the valve is clean If the valve has residues on it the water tank will not connect properly and might leak m For cleaning remove the plastic spout from the lid of the water tank m Wash the water tank and the plastic spout in the dishwasher or by hand with hot water and liquid dish soap Dry with a soft cloth m Clean the niche of the water tank Waste unit The display shows a message to empty the waste unit Clean the waste unit daily Coffee waste can mold if there is water in the waste unit from the rinse process There may be water in the waste container from the rinsing process This is normal Line the waste unit with a paper towel to make for easier cleaning m Pull the waste unit out m Wash the waste container in the dishwasher or by hand with hot water and liquid dish soap Dry with a soft cloth m Thoroughly clean the niche of the waste unit in the machine m Push the waste unit completely into the machine 47 Cleaning and care Drip tray The trip tray contains a sensor which causes the display to show when the tray is full and needs t
15. on the brew unit handle CD and turn the handle to the right to lock it into place Cleaning and care Cleaning the brew unit Depending on the oil content of the coffee the brew unit can clog Clean the brew unit approx every 200 cups with the enclosed detergent tablets They are specially developed for the coffee maker to optimize the degreasing The cleaning tablets can be purchased from Miele As a reminder the display shows Please run cleaning program after 200 cups and then until the machine is cleaned The cleaning process takes about 6 minutes ow Be EO m Tap or gt until Maintenance highlighted confirm with OK m Select Clean brew unit confirm with OK m Select Start confirm with OK m Follow the instructions in the display To avoid having to empty the drip tray too frequently place the small cleaning container beneath the main dispenser The inside of the machine is also rinsed therefore you will still have to empty the drip tray when prompted during the cleaning process When the display prompts you to Please drop the cleaning tablet in the ground coffee funnel m Remove the storage drawer and open the funnel lid m Drop a cleaning tablet into the funnel m Close the lid replace the drawer and close the machine door m Follow the instructions in the display m When the display shows Prog finished tap OK The brew unit is now degreased and the ma
16. plugs or outlets The reduction of power to the appliance caused by these devices will cause the appliance to run hot and may damage it and or shorten its usable life If there is any question concerning the electrical connection of this appliance to your power supply please consult a licensed electrician or contact Miele s Technical Service Department See back page for contact information 70 Installation Installation options The coffee system is designed to be built into cabinetry Miele appliances can be installed flush or proud Discuss your installation requirements with your architect designer and installer 17546 gt 3 451 5 mm 17 455 5 mm c L 3 y D Efe ES ant iC tr To 1 32 On to e A combination with other Miele built in appliances is possible If the machine is installed in combination with other appliances it should be installed with a protective base between the appliance and the unit exception installation with a built in plate warmer A special display cabinet is also available from your dealer or Miele as an installation option 71 Installation Installation Make sure power is not supplied to the appliance while installation or maintenance work is performed Disconnect the power supply to the work area by unplugging the unit tripping the circuit breaker or removing the fuse The coffee System must be installed into cabinet
17. the other m To fill two cups at the same time place one cup under each spout Be sure to wait for 2 dispensing cycles to be completed before removing the cups Interrupting preparation m Tap OK when you see Stop in the display Preparation will immediately stop Coffee and espresso prepared from ground coffee After filling the funnel with ground coffee see Filling water beans or ground coffee Filling ground coffee the display shows Wake the coffee Yes Mo m Tap or until Yes is highlighted Select No if no ground coffee is filled in the funnel Otherwise the coffee System assumes that ground coffee is in the machine and dispenses only water the next time coffee is made The display reverts to the main menu and you can select the desired beverage type Preparing drinks Prepare beverages m Place a cup under the main spout m Tap the OK button The appliance brews the espresso or coffee and the selected beverage is dispensed from the main spout Do not open the appliance door during the brewing process The appliance will be damaged After dispensing the appliance automatically reverts to bean operation Interrupt preparation m During preparation tap the OK button when Stop appears in the display Preparation will immediately stop If you use ground coffee only one serving is prepared at a time The appliance always uses the entire portion of ground
18. until the beverage symbol is highlighted tap OK once m To interrupt preparation tap OK again To set the proportions for beverages coffee espresso froth hot milk see Setting serving sizes After preparing the first drink with milk the reminder Clean the milk pipework will appear in the display m Tap OK to return to the main menu This reminder will not appear after each additional drink Preparing drinks User profile beverages After use The user profile function is used to prepare beverages to suit your taste by adjusting the amounts of water milk and ground coffee as well as temperature and pre brewing see Creating a user profile Before turning the machine off or at the end of the day flush the water lines the brew unit the spouts and the milk pipework in order to prevent the machine from clogging see Cleaning and care If you have already created a user profile first select it then prepare the beverage User profile m Tap or gt until User profile is highlighted confirm with OK m Tap or gt to select Select confirm with OK m Use or to select the desired user profile confirm with OK A large user profile symbol will appear in the display to show that a profile has been selected You can now operate the appliance as you would for a standard profile 20 Adjusting the coffee grinder The finer the coffee beans are ground determ
19. Miele Operating and Installation Instructions Coffee System with convertible water connection CVA 4066 To prevent accidents en US CA and appliance damage read these instructions before installation or use M Nr 07 818 660 Contents IMPORTANT SAFETY INSTRUCTIONS Luuuu iussis sss isses 4 Guide to the coffee system iioii iile eee 8 Included aecessorles sed tere denas bU D ck E Rot xot eee d nd a Rao Tu n 10 First steps to use lilii eel 11 TOUCHICONUOIS s cua dS ete EE E Dee CR ERROR a eee a Pa ede s 11 De ET E P 11 Preparing your appliance for an extended vacaion n saaa saaara 12 Filling water beans or ground coffee uuaa aaa 13 Filling the Water tenk susce sacs does dest Pawnee aR eee RUE RO se dn 13 Filling the bean container iiiiiee e aE EEA 14 Filling ground coffee 2 0 e es 14 Preparing drinks 0 0000s 15 TUNNG ON sb DTE 15 Preswatming eupS 4 5 cd Ak rt di wedi be ER n OR ed ea oe a RU ae 8 15 Adjusting main dispenser height 0 0 0 0 00 eee 16 Coffee and espresso prepared from coffee beans 0 2 00 00 eee 16 Coffee and espresso prepared from ground coffee 00 eee 17 Beverages with milK 242m qe beep epee Eod de aea iae ae oa 18 User profile beverages 0 000 ccs 20 Adjusting the coffee grinder 00 200 liliis 21 Seling ed edt e Sac et ee eee toned eee aia eee 22 LAN GQUAG
20. age Is the machine plugged in The machine goes into standby mode when not used for a programmed time See Settings Timer Switching off after Contact Miele s Technical Service Department Plug in the machine The light turns off suddenly The light turns off automatically when the machine has not been used for 15 minutes See Settings Lighting 55 Frequently asked questions What if the machine does not switch on even though the Switch on at timer setting is activated Possible fault Solution The System Lock is activated See Settings System Lock The display messages are difficult to read Possible fault Solution The contrast or brightness of the displays are too low high Adjust the display contrast brightness See Settings Display Little or no coffee or espresso is dispensed from the main dispenser Possible fault Solution The main dispenser connector cap is not positioned correctly see Guide to the machine Interior view Lubricate the cap with the supplied silicone grease No milk or milk froth comes out of the main dispenser Possible fault Solution The dispenser is clogged See Cleaning and Care The consistency of the milk froth is not unsatisfactory Possible fault Solution The air intake tube is clogged The air intake tube is fa
21. ater to the water tank The water tank must be positioned correctly or the valve will leak If the water tank has not clicked into place pull the tank out check and clean the niche Do not use deionized or mineral water They may lead to heavy calcium built up in the machine that can damage the unit m Open the appliance door Filling water beans or ground coffee Filling the bean container Only fill espresso or coffee beans in the beans container Anything else including ground coffee will damage the grinding unit Caramelized flavored or otherwise pre treated beans or sugar containing beverages must not be filled into the appliance It will damage the coffee system m Pull the bean container out m Push the lid back and fill the container with roasted coffee beans m Push the lid back into place and put the beans container back into the appliance m Close the door 14 Filling ground coffee A funnel for ground coffee is provided in case you would like to prepare a different coffee type e g decaffeinated coffee m Pull the storage drawer out of the appliance and lift the funnel lid CD m Place one spoonful of ground coffee into the funnel using the supplied spoon and close the lid m Push the drawer back into the appliance and close the door See Preparing drinks Espresso and coffee made from ground coffee Preparing drinks Clean the coffee system daily to
22. ault setting m With the machine turned off tap OK m Select Lighting confirm with OK m Select Brightness confirm with OK m To turn the lights off tap lt until the small white bars are no longer visible m Select Back 47 symbol twice to exit the menu Info displaying No of drinks The Info option allows you to display the number of beverages that have been dispensed from the machine and the number of beverages the machine can still make before descaling is necessary m Select Settings n confirm with OK m Tap or gt until Info is highlighted confirm with OK m Use lt or gt to select No of drinks or Portions until descaling confirm with OK Under No of drinks you can display Total number of coffees or a breakdown according to each individual coffee beverage milk froth milk and hot water m Tap OK to go back to previous menu When the machine requires descaling you will be notified automatically It is not necessary to check these messages regularly 29 Settings System lock The coffee system can be locked so that it cannot be used by children or those not familiar with the operating instructions When the machine is locked the timer setting Switch on at will not work Activating Deactivating the System lock m Select Settings pe confirm with OK STU Water hardness m Use or gt to select Safety confirm with OK m Tap or
23. be activated again when the machine is manually turned on the next time This safety measure is designed so that the machine does not turn on every day if the setting was not canceled before a longer time of absence e g vacationing 24 Switch off after The machine will turn off automatically to save energy after a programmed period of time ranging from 15 minutes to 9 hours after the last use When the Switch off after option is set the machine will turn off automatically after the programmed amount of time m Use lt or gt to select Switch off after confirm with OK A display of 1 00 for example indicates that the machine will turn off after one hour m Tap lt or gt to set the hours Confirm with OK Repeat to set the minutes The machine will now turn off after the programmed amount of time If the automatic rinse feature is turned on and the machine has been used to prepare a beverage it will always run a brief rinse cycle before turning off Settings Switch off at A specific time of day can be set to turn the coffee system off m Use lt or gt to select Switch off at confirm with OK m ap or to set the hours Confirm with OK Repeat to set the minutes The machine will turn on each day at the specified time one you have activated the timer see Activate If the automatic rinse feature is turned on and the machine has been used to prepare a beverage it wil
24. chine is ready for use 51 Cleaning and care Exterior To avoid scratches or discoloration immediately remove any soiling from the machine front m Turn off the machine using the On Off button m he front of the appliance can be cleaned with a sponge and a solution of warm water and non abrasive liquid dish soap Dry with a soft cloth Only use a slightly damp sponge when cleaning the controls Water could penetrate into the electronics and cause damage The external surfaces of the coffee machine are susceptible to scratching Scratches on the glass surface could also weaken the glass making it more susceptible to breakages Glass cleaners may be used to clean the exterior However do not allow them to sit or puddle this can cause damage to the surface Remove the cleaner promptly 52 To better maintain your appliance avoid the following cleaners containing soda ammonia thinners or chlorides cleaners containing descaling agents or lime removers abrasive cleaners stainless steel cleaners caustic oven cleaners scouring pads steel wool hard brushes eraser sponges metal scrapers Wipe any spills from descaling immediately Descaling the appliance The coffee system must be descaled regularly The appliance will display a reminder message to descale and will eventually lock if not descaled The display will show Please descale the coffee system Remaining number of se
25. clean the supply lines the brew unit and the main dispenser If you have turned off the automatic rinse feature see Settings Automatic rinsing the lines will need to be rinsed manually When performing a manual rinse cycle it is recommended that you place the small cleaning container under the main dispenser hWaintenance owe ge amp m Tap lt or gt until Maintenance amp is highlighted confirm with OK m Select Rinse the system confirm with OK m Select Start confirm with OK When the main menu reappears in the display the lines have been rinsed The appliance can now be turned off Cleaning and care Milk pipework Rinsing the milk pipework To prevent the milk residue from spoiling or drying in the machine and pipework you should rinse these lines after use In addition to rinsing after use the lines need to be cleaned at the end of the day MEUA gt FF highlighted confirm with OK m Select Rinse milk pipework confirm with OK m Select Start confirm with OK m Follow the instructions in the display To rinse the pipework in the lid of the stainless steel milk container fill the large cleaning container to the max mark with cold water Fit the lid of the stainless steel milk container into place on the large cleaning container Place the cleaning container in the appliance where the milk container would normally sit 42 Cleaning the milk pi
26. coffee loaded into the funnel for one beverage 18 Beverages with milk Stainless steel milk container The stainless steel milk container is vacuum insulated to keep milk cold for a period of time With an ambient temperature of about 68 F 20 C milk at 43 F 6 C can be stored for 11 12 hours and remain under 55 F 13 C Milk that is warmer than 55 F 13 C should not be used because it will not make good milk froth Milk cannot be stored as long if there is a warming drawer underneath the coffee machine Do not fill the container to the rim leave a gap of approx 1 1 1 2 2 3 cm from the top Make sure to keep the top and seals of the container clean Soiling can cause affect the functioning of the milk container Cold milk is best for creating froth Always pre warm the cup with hot water before you prepare a beverage Preparing drinks To prepare beverages with milk m place the lid on the stainless steel milk container and turn the lid to the left so that it clicks into place m Open the appliance door and hang the milk container in the appliance as shown m Close the appliance door Cappuccino latte macchiato hot milk froth m Place a suitable cup or glass under both dispensers For best results when preparing a latte macchiato place the glass under the spout in such a way that the espresso flows into the middle of the froth m Tap the right arrow button
27. e P Depending on the oil content of the coffee the brew unit may clog Clean the brew unit every 200 cups with a cleaning tablet The display shows a reminder message P Dispose of the coffee waste in a trash can not in the sink The sink could get clogged P Do not hang lean sit or place heavy items on the door The machine could be damaged P The use of accessory attachments not recommended by the appliance manufacturer may result in fire electric shock or injury to persons P The appliance is designed for use in room temperatures between 59 F and 140 F 15 C and 60 C Do not use the appliance outside of this range of temperatures SAVE THESE INSTRUCTIONS AND REVIEW THEM PERIODICALLY Guide to the coffee system Front view D On Off D touch control 2 Display 8 Left arrow to scroll through program options OK touch control to confirm selected program options and save settings 8 Right arrow to scroll through program options Hot water touch control Door grip Hot water dispenser 9 Lighting Drip tray Main dispenser height adjustable 42 Stainless steel milk container Guide to the coffee system Interior view D Main switch 2 Storage drawer 8 Ground coffee chute 4 Grind control slide Coffee bean container Drip tray with no spill grid for transport Water tank Brew unit 9 Waste unit 69 Main dispen
28. e bars the sound will turn off m Tap OK to save the setting 32 Water supply This machine is designed for use with or without a plumbed water connection If the Plumbed water supply option is set to On water is automatically taken into the water container If the option is set to Off the water tank will need to be filled manually m Select Settings n confirm with OK Settings Plumbed water suppl Showroom prag m Tap lt or gt until Plumbed water supply is highlighted confirm with OK m Use lt or gt to select On or Off confirm with OK Settings Showroom program The showroom program is used to demonstrate the machine at exhibits In this demo mode the machine lighting is On but the machine does not heat up Restoring factory default settings The Factory default setting can be used to reset different settings back to their original default status You can select whether to reset all settings or delete any user profiles m Select Settings Pee confirm with OK Settings Factory default Back gt m Tap or gt until Factory default is highlighted confirm with OK Two options are now available User profiles Selecting User profiles deletes all user profiles that you have entered leaving only the default standard profile m Under User profiles select Reset confirm with OK The user profiles are deleted All settings Selecting
29. ed important it is to pre heat The temperature is set too low Check on what temperature range the coffee type is set Check if the brew unit is clogged Clean the brew unit No drink is prepared although the beans were grinded and enough water is in the container Possible fault Solution The grind control is set to the finest Adjust the grind control slide to a or the amount of coffee is set to the different position or the amount of maximum coffee more or less The process is timed the process might need so long there is no time for brewing any more The door cannot be closed Possible fault Solution Checkif all containers are properly inserted The door hinges need to be See Installation Instructions adjusted The steam heating system is turned off but steam can still dispensed Steam can be dispensed as long as the steam heating system is heated Once it has cooled steam can only be dispensed once the steam system has heated 58 Frequently asked questions The coffee dispensing is interrupted Possible fault Solution The water tank is empty If the unit is plumbed check the water line and plumbing If the unit is used with the water tank refill the water tank with fresh cold tap water You will be asked whether you would like the coffee dispensing to continue after the water tank has been filled If y
30. eere re eea Aaah wand wh Rie a aie eee ee e we ante hs 22 Tittiesor day cd beo erie hd Hebe oh heed dobed b Ph E T edd oA pelt is 23 NI T ATTI wnt een ddan ee ee 24 Coffee jug dispensing several servings one directly after another 25 Atmount ot coffee s neue prima ong RR doo Ee X IRSE Daw Due SR e quie tes 26 P DONN s nter ok ie iesu RR SRI signe ae reden aea UR inde nine Le Regen ae 26 Temperat le xe nce SEC ec HO tont c e beige X oe OR ee e n act nn 27 Automate INSING us acu tete oe to eoe t ac db coe X e ur EC REOR ee ad t ie 27 SteartiiSyStem us var xe ee eX X bade Xes used E ES 28 Lighting Adjusting the brightness iiie 28 Lighting Setting the switch off time iilis 29 Info displaying No of drinks 2 0 02 II 29 VSS MMOGs ete REEERRERS IURE CIR IRSE kaart aire alain 30 Water hardness 5 scusa sory nate ee mink Pe P c ae BSA ACE Ie aS 30 Contents BILL M c 31 Tene OPUONS eic ue reae deren obe hin dd aoo do doe bo dn dope delete ue rape 32 Water Supply emerit MPN C een nh Se aon c Pee Rn ee idet AUR crece 32 ShoWroom pOOfFalTis ios Sees deo eh ied b esie e tpi Arteta he 33 Restoring factory default settings ies 33 Setting the serving sizes illl o le een 34 User profiles eme io ooo E EE Ree ee EAE Ke Rin ea 37 Selecting a user profile sses cocinero eC a e d Gets dur EO cea ee 37 Cleaning and care 02 0 e 40 Quick Guide isse ee eee 40 Descaling the
31. enser Pull out the nozzles of the main dispenser see Main dispenser m Open the appliance door m Remove the stainless steel milk container and clean it particularly the lid see Stainless steel milk container m Unlock the cover for the milk pipework by pressing in the two brackets on the left and right 43 Cleaning and care m Remove the cover with the milk m Insert the brush into the milk hoses pipework Clean the whole part in the one after the other from below Push dishwasher without taking it apart the brush back and forth to the end until there is no more no milk residue If there are milk residues in the milk in the hoses pipework you can clean them with the cleaning brush provided To do this Reassemble the milk pipework as take the cover and the milk pipework follows apart as follows m Push the retainer with the plug onto the cover as shown Make sure that the retainer is sitting properly on the cover Do not pull the milk hoses off the retainers This may cause the milk pipework to leak m Press the small recess on the dispenser retainer and pull the retainer out towards the front Take the milk hoses off the guide rail m Grasp the second retainer by the stud 9 and pull it up and off Now you can clean the hoses with the brush under running water 44 Cleaning and care m Then press the milk hoses into the guide rail and push the dispenser reta
32. enser Plastic parts of the unit could catch fire P The hot water and steam dispensed could cause scalding These functions must be used carefully Never hold any parts of the body under the steam nozzle or the hot water dispenser The machine must never be used to clean objects P Never use a steam cleaner to clean the appliance Pressurized steam could damage electrical components and cause a short circuit P Clean the coffee system daily to prevent bacterial growth All parts of the coffee system are dishwasher safe except for the brew unit bean container stainless steel milk container and lid and main dispenser cover Failure to properly maintain machine may cause health issues P Be aware of how long milk in stored in the milk container If milk is not continually cooled it can readily spoil causing illness Be sure the milk container and pipework are properly cleaned and maintained See Cleaning and Care for more information P To avoid injuries allow the coffee system to cool before cleaning or putting on and taking off parts Turn the machine off at the main switch when not in use and before cleaning P The appliance must be descaled regularly with the supplied descaling tablets In areas with very hard water the machine may need to be descaled more often P Only use the descaling tablets provided by Miele Take care to use the correct mixture of water and descaler otherwise it may cause damag
33. espresso The grind grade can now be reset Close the lid of the ground coffee funnel Adjust the door with the door hinges See Installation Adjusting the door hinges Lubricate the cap of the connecting piece with the supplied silicone grease The water tank has automatically filled 63 Frequently asked questions The message Check brew unit appears on the display Possible fault Solution The brew unit is clogged Follow the display prompts Clean the brew unit see Cleaning and care Brew unit Set the amount of ground coffee and the grinder setting to the medium settings also adjust these settings in the user profiles See the respective chapters in this manual The message Fault 28 appears on the display Possible fault Solution If too much ground coffee passes through the coffee chute the machine is unable to process it Tap the button next to OK The machine is again ready for use One of the messages Fault 1 to Fault 4 or Fault 80 to Fault 83 appears in the display Possible fault Solution Switch off the machine using the On Off button and wait about one hour before switching it on again If the fault message appears in the display again call Customer Service The message Fault 74 or Fault 77 appears in the display Possible fault Solution Turn the mach
34. function off The default factory setting for the pre brew function of your machine is Off without m Select Settings n and confirm with OK Settings Pre brewing Temperature m Tap lt or gt until Pre brewing is highlighted confirm with OK m Tap or until the desired pre brew setting is highlighted Tap OK to save the setting Settings Temperature Five temperature settings are available for each coffee selection and three settings for hot water Not every coffee type allows high temperatures Some types react so sensitively that the crema cannot be properly built m Select Settings Pee and confirm with OK Settings Temperature Automatic rinsing m Tap or gt until Temperature is highlighted confirm with OK m Tap or gt until the beverage is highlighted in which you wish to set the temperature for Confirm with OK m Tap or gt until the desired temperature is highlighted m Tap OK to save the setting Automatic rinsing It is important to flush out any residual coffee from the lines when starting to use the machine for the day If the automatic rinse function is activated and the machine is cold the rinse cycle will begin automatically as soon as the machine is turned on This will also pre heat the lines with the hot water used during the rinse cycle This is indicated by a message in the display If a beverage has already been made the machine wi
35. ge user symbol 37 User profiles Creating a user profile m Tap lt or gt until Create is highlighted confirm with OK Up to 9 user profiles can be created If you try to create more than 9 user profiles the message Memory full will appear you will need to delete a profile to create space Letters and numbers will now appear in the display Use or to select the desired letters or numbers A new word will always be capitalized the appliance will then switch to lower case letters m Use or to select the desired characters m Tap OK to confirm a character You will see the selected characters in the top line of the display If you misspelled a word use the arrow buttons to select the trash can symbol confirm with OK The last character entered will be deleted 38 Saving an entry m Once you have completed an entry use lt or gt to select OK confirm with OK The display will briefly show the User profile welcome screen followed by the main menu Canceling an entry m f you do not wish to save an entry you have made use or to select back confirm with OK Changing a user profile m Select Change user profile confirm with OK m Select the user profile you wish to change confirm with OK Continue as you would for Creating a user profile User profiles Deleting a user profile m Select Delete user profile confirm with OK m Use
36. gin the descaling process The display prompts the user through the single steps of the descaling process Follow the prompts If the descaling is started while the machine is still hot the appliance will cool down for 10 minutes before the descaling begins The descaling process cannot be canceled once OK is selected The process now needs to be completed This is a safety feature to ensure the process will be completed It is important for best results and the longevity of the machine To dissolve the descaling tablets m Remove the water tank and fill it up to the S mark with lukewarm water Do not under fill the water tank because this will cause the descaling cycle to end prematurely before completion 54 m Add 2 descaling tablets to the water and allow them to dissolve completely before closing the water tank and placing it back into the machine During the descaling cycle the descaling agent water solution will run out of the hot water spout and the main dispenser This will be followed by a pause to allow the solution to dissolve the internal mineral buildup after which more descaling solution with be released from the spouts This process will repeat itself until the cycle is finished m When the display prompts you to Add fresh water to tank rinse the tank thoroughly with clear water all traces of descaling residue must be removed and fill it with clean drinking water up to the k mark Dur
37. id ean the main dispenser ean the water tank ean the drip tray and no spill grid Once a week more often if there is a heavy soiling ean the main dispenser connector ean the interior ean the inside door tray Ri C C C C Clean the waste unit C C C C C ean the brew unit O ean the front of the appliance especially right after descaling Once a month Lubricate the cap on the main spout connection Approx every 200 portions Clean the brew unit use the cleaning tablets Depending on the water hardness Descale the appliance When necessary 40 Clean clogged milk pipework Clean the bean container Cleaning and care Allow the coffee system to cool before cleaning Danger of burns Do not clean the unit with a steam Cleaner Never use cleaners containing chlorides sand baking soda or scouring agents These will damage the surface To avoid mold growth and odors it is important to clean the machine regularly All removable parts are dishwasher safe except the following Brew unit Bean container Stainless steel milk container and lid Main dispenser cover When the parts are cleaned in the dishwasher they might get discolored by food residues such as tomatoes or their surface coating may become damaged Rinsing the system Before switching your machine off for an extended period of time you should
38. ine off and then on again after a short period of time If the fault message appears in the display again call Customer Service 64 Frequently asked questions The message Fault 73 appears in the display Possible fault Solution The brew unit cannot reset to the Take out and clean the brew unit correct position See Cleaning and Care Brew unit Push the coffee ejector of the brew unit into the correct position Set the brew unit aside and insert the waste unit and the water tank Close the door The brew unit motor will automatically move to the correct position When the message Fit the brew unit appears open the door and insert all parts into the machine Close the door If the message still shows contact Miele Technical Service 65 After sales service In the event of a fault which you cannot easily fix yourself please contact the Miele Technical Service Department at the contact information on the back of this booklet When contacting the Technical Service Department please quote the model and serial number of your appliance given on the data plate inside the appliance 66 MieleCare USA only MieleCare our Extended Service Contract program gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership MieleCare is the only Extended Service Contract in the industr
39. iner 2 on until it clicks into place m Put the cover with the milk pipework back into the rear of the appliance door Reattach the main dispenser see Main dispenser Stainless steel milk container The stainless steel milk container and lid must be cleaned by hand with hot water Make sure to keep the top and seals of the container clean Soiling can cause affect the functioning of the milk container m Clean the stainless steel container with hot water m Rinse the handle under running water and then clean it thoroughly with a damp cloth to remove all milk residue m f the milk pipework in the lid is clogged clean under running water using the cleaning brush Insert the cleaning brush into the line and push it in and out 45 Cleaning and care Main dispenser m Pull the main dispenser all the way down and pull the cover forward to remove 2 m urn the cover around slide the m Slide the insert back into the cover 46 insert upward and out and clean both parts thoroughly until it clicks into place Pull the nozzles of the main dispenser out m Pull both rubber stoppers out and clean the stoppers and nozzles thoroughly m Pull the air intake pipe out if necessary You can knead or blow through the pipe to remove any potential blockages Never use a sharp object to remove blockages this could damage the parts m Put the rubber stoppers back
40. ines the strength of the coffee and the quality of the crema To prevent machine damage adjust the coffee grinder one level at a time and let the beans grind before adjusting another notch Otherwise the machine will be damaged The grinder should be adjusted If the espresso flows too quickly into the cup the pressure cannot be built up because the beans have been ground too coarsely The grinder should be adjusted to a finer setting If the espresso only trickles into the cup the beans have been ground too fine and the coffee will be bitter The grinder should be adjusted to a coarser setting If the crema is evenly colored but pale the ground coffee is too coarse If the crema is very dark brown on one side graduating almost to white on the other the ground coffee is too fine To adjust the grinder setting m Push the slide control to the left for a finer grind or to the right for a coarser grind You should be able to feel the notches when moving the slide control If the slide control will not move m Close the machine and dispense a cup of coffee Then try to move the slide control again 21 Settings The coffee system can be customized to suit individual preferences Settings menu Settings P m Tap lt or gt until Settings is highlighted Confirm with OK m Tap or gt until the desired option is highlighted and confirm with OK The current setting s will be marked
41. ing rinsing water will run out of the dispensing spouts Because the inside of the machine is also rinsed out you must empty the drip tray in the final step m When the display shows Prog finished tap OK The appliance is now fully descaled and ready for use If the appliance was set to the plumbed water supply before descaling once the descaling process is complete it will return to that setting Frequently asked questions Repairs to electrical appliances should only be carried out by a suitably qualified person in accordance with local and national safety regulations Repairs and other work by unqualified persons could be dangerous The light does not illuminate when the appliance is turned on Possible fault Solution Is the lighting turned off See Settings Lighting If not the lighting is defective Contact Miele The display remains dark Possible fault Solution The main switch is turned to 0 The plug is not inserted into the socket correctly The fuse has blown or is defective Turn the main switch to I Plug the machine in lf the fuse has blown contact Miele s Technical Service Department The unit suddenly turns off Possible fault Solution Is the machine programmed to switch off after a programmed time There could be pebbles within the coffee beans The unit shuts off after 20 secs to avoid dam
42. it for a moment to pre warm the cup then empty the cup and prepare the beverage Preparing drinks Adjusting main dispenser height The height of the main dispenser can be adjusted to keep the shortest distance to the cup and retain heat and maintain a better crema and froth m Slowly pull the main dispenser up or down as desired Coffee and espresso prepared from coffee beans Espresso coffee double espresso and double coffee are all prepared in the same way m Place a cup under the main dispenser both dispensers at the same time 16 The beverage is dispensed through m Use the arrow buttons to select the desired beverage confirm by tapping OK once The machine grinds the beans and pre brews the coffee if On is selected under Pre brewing The selected beverage is dispensed Do not open the appliance door during the brewing process The appliance will be damaged Discard the very first two coffees _ dispensed once you have started to _using the appliance this will ensure that any coffee residue from factory testing is eliminated from the brew unit Preparing drinks Double portion If you would like a double portion of coffee or espresso or to prepare two portions at the same time m tap the OK button a second time while the display reads 2 portions The two portions are always prepared one after
43. iver 73 74 75 Please have the model and serial number of your appliance available before contacting Technical Service U S A Miele Inc National Headquarters 9 Independence Way Princeton NJ 08540 Phone 800 843 7231 609 419 9898 Fax 609 419 4298 www mieleusa com Technical Service amp Support Nationwide Phone 800 999 1360 Fax 888 586 8056 TechnicalService mieleusa com Germany Miele amp Cie KG Carl Miele StraBe 29 33332 G tersloh Canada Miele Limited Headquarters and Showroom 161 Four Valley Drive Vaughan ON L4K 4V8 Phone 800 643 5381 905 660 9936 Fax 905 532 2290 www miele ca professionalQmiele ca commercial enquiries MieleCare National Service Phone 800 565 6435 905 532 2272 Fax 905 532 2292 customercareQmiele ca general and technical enquries Alteration rights reserved 0711 Ce M Nr 07 818 660 01 INFORMATION IS SUBJECT TO CHANGE PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS TECHNICAL amp WARRANTY INFORMATION
44. l always run a brief rinse cycle before turning off Activate m Use lt or gt to select Activate confirm with OK The program items Switch on at and Switch off at are displayed O Switch off at m Use lt or gt to select the program item s you wish to activate Tap OK to activate select the check box or deactivate clear the check box the desired option m Use or gt to select Accept confirm with OK m Use lt or gt to select Back confirm with OK Coffee jug dispensing several servings one directly after another With this function you can dispense up to eight servings of coffee one immediately after another max 1 qt 1 1 The brewing process will run automatically for all servings m From the main menu select Settings pe then tap ok Settings Coffee jug Frog the amount m Tap the right arrow button until Coffee jug is highlighted and then tap the OK button m Using the arrow button select the number of servings you wish to be dispensed 3 to 8 and confirm with OK m Place the desired container under the main dispenser and follow the instructions on the display Each cup of coffee will be individually ground brewed and poured Meanwhile the display reports on the process while it is going on You can interrupt the process at any time by tapping the OK button Stop m When the display shows the process is complete confirm with OK 25
45. liance If the Descale reminder did not appear retest the water hardness to ensure that the machine is set correctly No water flows from the main dispenser Possible fault Solution The filters in the brew unit are clogged Rub any residue off the filters with a sponge See Cleaning and Care The brew unit or waste unit could not be pulled from the machine Possible fault Solution The brew unit is not in the correct position The door was opened during grinding or brewing Close the door The brew unit automatically gets into the correct position No crema has formed or it is different Possible fault Solution Check if the grind setting is too coarse or too fine Check what temperature range the coffee type is set If the temperature is too high there are black areas in the crema Some coffee types produce too much crema when the coffee espresso temperature is set to the maximum and the amount of ground coffee is too much Adjust the grind setting Lower the temperature and amount of ground coffee See Settings The coffee is not fresh enough The coffee is unsuitable for use in this machine The coffee dispensers are set too high 61 Frequently asked questi ons The message Insert water tank until it engages appears Possible fault Solution No water is dispensed
46. ll also automatically run a rinse cycle just before turning off The factory default setting for the automatic rinse function is On If you do not want the rinse water to collect in the drip tray always place an empty cup or the small cleaning container underneath the main dispenser m Select Settings hn confirm with OK Settings Automatic rinsing Steam system m Tap or gt until Automatic rinsing is highlighted confirm with OK m Tap lt or gt to select On or Off confirm with OK It is recommended that you set this program option to On to ensure that the rinse cycle will not be forgotten 27 Settings Steam system This appliance has two heating systems making it possible for you to prepare milk froth hot milk and coffee espresso one right after the other If you seldom need milk froth or hot milk you can turn the steam heating system off to save energy If you select milk froth or hot milk with the steam heating system turned off it will take a little longer as the heater is only turned on once a milk option is selected The steam heating system will remain On until the machine has been turned off completely m Select Settings pe confirm with OK Settings Steam system Lighting m Tap or gt until Steam system is highlighted confirm with OK m Tap lt or gt to select On or Off m Tap OK to save the setting 28 Lighting Adjusting the bright
47. m Confirm the message with OK Turning off m Tap the On Off button to turn the machine off If the automatic rinse feature is enabled the machine will start the rinse cycle as soon as a coffee or milk based drink has been dispensed It will not shut off until after the rinse cycle is complete Preparing your appliance for an extended vacaion If you elect to turn off the water to your home for an extended period of time please note that this may not be enough to reduce the risk of a leak To be completely safe you must turn off the water supply to each individual appliance This means under the sink for a dishwasher at the laundry bib for your washer etc Filling water beans or ground coffee Clean the appliance thoroughly before loading the water tank and bean container see Cleaning and care Be sure to enter the water hardness see Settings Water hardness Filling the water tank m Pull the water tank out m Fill the container with fresh cold tap The beans and the water quality is water to the Max mark important for a good espresso or coffee The water tank must be washed The valve on the water tank ensures and filled with fresh cold drinking water that water cannot leak out before each day of use The unit displays a reminder when turned on m Close the lid and push the water tank into the unit until it clicks into place Never add hot water or any other liquids except cold w
48. n the appliance and remove any protective film before the first use See Cleaning and Care Turning on m Select On Off to turn the machine on The first few times the machine is turned on with the main switch a welcome screen will appear briefly on the display followed by additional messages The welcome screen is displayed each time the machine is turned on until 5 drinks have been prepared Niele Welcome During the very first use you will be prompted to select a language m Tap or gt until the desired language appears in the display m Confirm with OK The language is now set First steps to use You will then be prompted to set the Time format m Tap or gt until the time format you wish to select 12 hour or 24 hour is highlighted confirm with OK m Enter the Time of day First set the hours using or confirm with OK Repeat to set the minutes m Now specify when the time of day should be displayed On The time will be displayed even when the machine is turned off On for 60 seconds The time will be displayed for 60 seconds after the machine has been turned off Do not display The display will go dark as soon as the machine is turned off m Confirm with OK m Select OK to confirm the message indicating that your coffee system is communication enabled 12 If everything has been entered correctly Set up successful will appear in the display
49. ness The brightness of the machine lighting can be adjusted m Select Settings n confirm with OK es Info m Tap or gt until Lighting is highlighted confirm with OK m Select Brightness confirm with OK m Use or to select a lighter or darker setting m Confirm with OK to save the setting To turn the lighting off m Tap until the small white bars are no longer visible Settings Lighting Setting the switch off time Whenever the machine is On the machine lighting is also On The lighting turns off automatically when the machine has been idle for 15 minutes When the machine is turned off you can program the lighting to remain On and to shut off automatically after a certain amount of time if the machine is not used You can choose a duration from 15 minutes to 6 hours m Turn the machine off m With the machine turned off confirm with OK m Select Lighting confirm with OK m Select Switch off after confirm with OK m Use lt or gt to select a switch off time confirm with OK m Select Brightness and tap OK m Tap the arrow button to increase or decrease the brightness then tap OK to save the setting Factory Default Off m Select Back symbol twice to exit the menu The machine will now automatically turn the lighting off after the programmed amount of time If you do not want the coffee machine lighting on after the machine is turned off def
50. o be emptied Clean the drip tray daily Remove the drip tray after the final rinse when no more water runs from the lines Carefully remove the drip tray from the machine the water may be very hot and could cause scalding m Open the door and pull the drip tray out The drip tray contains a grid to avoid spilling during transport 48 m Wash the drip tray and grid in the dishwasher or by hand with hot water and liquid dish soap then dry with a soft cloth Take care that the metal contacts at the back of the drip tray are clean and dry If the contacts are soiled or wet the unit cannot detect when the drip tray is full and needs to be emptied m Push the drip tray with grid along the right edge all way in the machine m Close the door Drip tray cover m Remove the drip tray cover and wash it Cleaning and care Bean container The bean container must be cleaned by hand with hot water and liquid dish soap Do not use a dishwasher m Pull the bean container out and push the lid back m Wash the bean container by hand with hot water and liquid dish soap then dry with a soft cloth m Push the lid back and reinsert the bean container into the machine Main dispenser connector A connecting piece between the brew unit and the main dispenser is located on the inside of the door m Clean this connector regularly with a damp cloth without removing the lubricant for the cap
51. ou do not confirm with OK within 5 minutes the coffee preparation will be canceled Instead of coffee only water is dispensed Possible fault Solution The beans may have gotten stuck The ground coffee funnel cover was opened and closed and a preparation with ground coffee was selected but no ground coffee was inserted The coffee system switches automatically back to bean use after preparation Pull the bean container out and push it back in The drip tray is empty but a message to empty it is displayed Possible fault Solution The metal contacts are soiled or wet Check if the drip tray is inserted correctly Clean and dry the contacts nsert the drip tray as described in Cleaning and Care Drip tray Turn the machine off and on again with the main switch If the message still appears contact Technical Service 59 Frequently asked questions feature is set to On The machine does not rinse when turned on although the automatic rinse will not rinse when it is too hot When the machine is still at a temperature of about 140 F 60 C The machine The water or milk dispensing stops when programming the serving size Possible fault Solution There was not enough water in the tank or milk in the milk container The dispensed amount will not be saved If the maximum amount is dispensed the
52. pework To prevent milk residue from spoiling or drying in the machine and pipework it should be cleaned at the end of each day milk was used to make a beverage m f the milk pipework in the lid is clogged clean under running water using the cleaning brush Insert the cleaning brush into the pipework and push it in and out EEA T a RECEN M E m Tap lt or gt until Maintenance A is highlighted confirm with OK m Select Clean milk pipework confirm with OK m Select Start confirm with OK m Follow the instructions in the display Cleaning and care To rinse the pipework in the lid of the stainless steel milk container fill the large cleaning container to the max mark with lukewarm water to dissolve the cleaning agent Fit the lid of the stainless steel milk container into place on the large cleaning container Place the cleaning container in the appliance where the milk container would normally sit Use only Miele cleaning agent which was developed especially for this coffee system You can obtain this cleaning agent from your Miele dealer or the Miele com website The cleaning process has now begun When Prog finished appears on the display the lines are clean and you can turn the machine off Cleaning clogged milk pipework If no milk just steam comes out of the main dispenser the milk pipework in the appliance door may be clogged m Take the lid off the main disp
53. prevent bacterial growth All parts of the coffee system are dishwasher safe except for the brew unit bean container stainless steel milk container and lid and main dispenser cover Failure to properly maintain machine may cause health issues See Cleaning and Care The lines should be rinsed daily before the first use This will happen automatically if the rinsing feature is set to On see Settings Rinse Automatic and the machine is cold After heating hot water runs out of the two spouts into the drip tray If the rinse feature was set to Off select Rinsing to rinse the lines See Cleaning and Care Rinsing the system Turning on m Select On Off D The following message appears in the display Heating phase If the automatic rinse feature is set to on factory default the following message is displayed after the heating phase Water will now flow from the main dispenser and into the drip tray The machine will notify you when the drip tray is full but the tray should be emptied daily The main menu then appears in the display Pre warming cups All beverages should be made ina warm cup to develop the aroma The smaller the amount of coffee or espresso and the thicker the cups the more important it is to pre warm the cups m Place an empty cup under the hot water spout m Select hot water Bj m Hot water is dispensed Select OK to stop the flow m Let the hot water s
54. r Latte Macchiato Hot milk Milk froth Espresso Latte MWMacchiata O Hot milk O Milk froth m Use lt or gt to reach the option you wish to program to a certain serving size Tap OK to place a check mark next to the desired component to show that you would like to program this component m Repeat this process until all components you wish to program the serving size for are marked with a check Use lt or gt to select Start confirm with OK The appliance now begins preparing a cappuccino or latte macchiato As soon as the component which you have checked is being dispensed the display will read Program the amount m Once the cup is full to your liking with that component and Save appears in the display tap OK to save the amount m Repeat this process for the other components you have chosen for this type of coffee Each time the drink is prepared it will contain the programmed amount of coffee milk etc 35 Setting the serving sizes Setting the serving size for hot water m Place the desired cup under the hot water dispenser m Tap 5G until the display reads Prog the amount m Tap again once the cup is filled as desired and Save appears in the display Each time the hot water is prepared the programmed amount will be dispensed 36 Setting serving sizes via Settings m Select Settings n confirm with OK Settings Frog the amount Amount of
55. rogram four hardness levels on the machine Level 1 soft 0 3 gr gal 0 3 d Level 2 moderately hard 4 7 gr gal 4 7 d Level 3 hard 7 15 gr gal 7 14 d Level 4 very hard 15 22 gr gal 14 21 d m Select Settings Pee confirm with OK Settings Display m Tap or gt until Water hardness is highlighted confirm with OK m ap or to program the water hardness level confirm with OK The selected water hardness level is now saved Display The display contrast and brightness can be adjusted m Select Settings Pe confirm with OK Settings Displa Volume m Tap or gt until Display is highlighted confirm with OK m Tap or gt to select Contrast or Brightness confirm with OK m Tap or to adjust the contrast lower or higher or make the display brighter or darker m Tap OK to save the setting 31 Settings Tone options A tone can be selected to confirm the selection of a touch control The volume of the tone can also be adjusted m Select Settings Pa confirm with OK Settings volume Flumbed water supply m Tap or gt until Volume is highlighted confirm with OK m Tap or gt to select Buzzer tones or Keypad tone confirm with OK m Tap or gt to increase or decrease the volume If you continue to tap all the way to the left until you can no longer see the small whit
56. rvings 50 This message will now appear after each preparation m Tap OK to acknowledge this message If the counter has elapsed to O the appliance will be locked and the display reads Please descale m Tap OK to start the descaling cycle immediately Descaling takes about 20 minutes If you want to continue at a later point in time turn the unit off The appliance can only be used again once descaling is performed The machine will automatically switch to water container operation for the descaling program Only use the enclosed descaling tablets for descaling They are specially developed for the coffee system to optimize the descaling The descaling tablets can be purchased from Miele Other agents may damage the machine and affect the taste of coffee and hot water The machine could also be damaged Use the correct proportion of descaling agent in solution to prevent damage to the machine Use the supplied cleaning containers to protect the appliance front from the descaling agent Clean up any descaling spills immediately to avoid damage to the appliance front Thoroughly clean the water tank and the drip tray of descaling residues 53 Descaling the appliance Descaling ewe wg amp m Tap lt or gt until Maintenance A is highlighted confirm with OK m Select Descale and confirm with OK or when the appliance is switched off tap the OK button m Select Start tap OK to be
57. ry before being used m Unscrew the height adjustable feet This unit should only be used in on the underside of the machine room temperatures ranging between about 1 16 2 mm 59 F and 140 F Do not use the appliance outside of this range of temperatures m Push the appliance all the way back into the cabinet and center it If necessary level the unit with the four height adj le feet To align the appliance door flush with aight adjustakie ieni the kitchen cabinetry there must be a The feet can be turned out up to 3 8 sealing strip around the installation 10 mm recess otherwise a sealing strip must be put in place around the appliance plug the appliance into the electrical outlet m If there is no sealing strip around the installation recess stick the Miele sealing strip onto the appliance from the back before putting it into the recess Sealing strips are available from Miele 72 Installation Adjusting the door hinges The door hinges can be adjusted if the door cannot be opened easily m Push the appliance into the niche m Open the door and partially tighten the screws m To adjust the door sideways turn screw 0 m Carefully turn the lower screws CD to center the machine m To adjust the door to the front or back 2 t m To secure the appliance in the turn screw cabinet tighten the upper screws by hand Do not use an electric screwdr
58. ser connector connects the brew unit to the main dispenser amp 3 Stainless steel milk container amp 2 Main dispenser connector cap Guide to the coffee system Included accessories Cleaning agent Stainless steel milk container For daily cleaning of the milk pipework Cleaning tablets To hold and insulate milk with lid handle and additional cover for storing milk in the refrigerator not dishwasher safe To clean the brew unit Cleaning containers Descaling tablets To descale the coffee system Large and small for rinsing and cleaning the milk pipework Additional accessories are available Coffee spoon Contact Miele or visit the Miele iin website for more information To measure ground coffee 10 First steps to use Touch controls Select a touch control with your fingertip to use the machine Display The main menu in the display shows the following symbols gt w E y ux Espresso Coffee Cappuccino Latte macchiato Hot milk Milk froth User profile for up to nine different users Maintenance programs Settings to customize your coffee system m Use the arrow buttons to select a program item from the display Once highlighted confirm with OK Before the first use The appliance must be correctly installed and connected before the first use See Electrical connection Plumbing and Installation instructions Clea
59. set the appliance to suit your preferences for cappuccino and latte macchiato To program serving sizes you can either press and hold the OK button or via the Settings option When a user profile is activated the serving size is set for that particular profile only If you want to set the serving size for all profiles select the Standard user profile 34 Setting serving sizes of espresso coffee hot milk and milk froth using OK m Place the desired cup under the main dispensers m Select the beverage type m Press and hold OK until the display reads Prog the amount m Tap OK again once the cup is filled to your desire Save appears in the display The programmed volume of water or milk will now be dispensed each time that particular drink is selected Once the maximum water or milk volume is reached the appliance automatically stops the water supply The maximum fill amount for each beverage is then stored If the water tank or milk container becomes empty during portion programming the process is canceled and the size is not stored Setting the serving sizes Setting serving sizes for cappuccino and latte macchiato using OK m Place the cappuccino cup or latte macchiato glass you will be using to set the portion size under the main dispensers m Select cappuccino or latte macchiato m Press and hold OK until the display shows the options for Cappuccino Milk froth Espresso o
60. ssibility of recycling these materials Ensure that the appliance presents no danger to children while being stored for disposal Before discarding an old appliance unplug it from the outlet cut off its power cord and remove any doors to prevent hazards Plumbing Connection to the water supply m Disconnect the machine from the The machine must be connected to the water supply in accordance with local and national regulations The water being used should have the drinking water standards of the respective country where the machine is used All units and systems used to deliver the water to the coffee system must conform with the requirements of the respective country Only connect the machine to the cold water supply The machine can be connected without a non return valve The on site water line must have a water valve to turn the water off if needed If not present have a water valve installed by a licensed plumber The water faucet must be accessible after installation Water pressure on site Minimum 14 5 psi Maximum 145 psi if higher install a pressure reduction valve Suitable 1 4 tubing or copper piping must be supplied for plumbing To ensure the best coffee quality the maximum length of the tubing or copper pipe should not exceed 4 ft 11 1 5 m If too much water remains in the tubing the coffee quality could be affected electrical supply m Remove the water connection co
61. stem and the appliance P Install or locate this appliance only in accordance with the provided installation instructions 6 Use Caution Do not look directly or with an optical instrument into the lighting laser radiation Caution Risk of burns when dispensing hot beverages they are extremely hot P Before the first use flush the supply lines for water and milk and thoroughly clean the coffee system and stainless steel milk container P Only fill the water tank with cold fresh tap water Warm or hot water or any other liquids may damage the machine The water should be changed daily to prevent bacteria or mold growth P Do not use deionized or mineral water They may lead to heavy calcium built up in the machine that can damage the unit P Do not put anything but coffee beans into the beans container Do not put ground coffee in the beans container it will damage the grinding unit P Do not fill anything but ground coffee or a cleaning tablet for the brew unit in the funnel for ground coffee otherwise it will get damaged P Only use plain milk Flavored milk products contain substances that can clog the coffee system IMPORTANT SAFETY INSTRUCTIONS P Sugar can damage the appliance Caramelized or otherwise pre treated coffee beans or other sugar containing beverages must not be put in the machine P Never place a cup with an alcohol coffee mixture underneath the main disp
62. tem for an extended period of time e g vacationing P Installation work and repairs must only be performed by a trained technician in accordance with national and local safety regulations Repairs and other work by unauthorized persons could be dangerous and may void the warranty IMPORTANT SAFETY INSTRUCTIONS P While the appliance is under warranty repairs should only be performed by an authorized service technician Otherwise the warranty is void P Defective components should be replaced by Miele original spare parts only Only with these parts can the manufacturer guarantee the safety of the appliance P To protect against fire electric shock and injury to persons do not submerge the cord or plugs in water or other liquids P Do not let the cord hang over the edge of a table or counter or touch hot surfaces P Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Contact Miele P Always attach the cord to the appliance first then plug it into the wall outlet To disconnect turn the machine off then remove the plug from the wall outlet P Never open the outer casing of the appliance Tampering with electrical connections or components and mechanical parts is dangerous and may cause machine damage P If installed in combination with another appliance a protective base must be installed between the coffee Sy
63. ulty Clean the air intake tube see Cleaning and Care Any blockages can be removed by kneading or blowing through the pipe to remove any potential blockages Never use a sharp object to remove blockages this could damage the parts Remove the air intake tube and replace it with the supplied spare part 56 Frequently asked questions The display prompts me to fill or insert the stainless steel milk container even though the container has already been filled and inserted Possible fault Solution The container needs to be cleaned See Cleaning and Care The grinding sounds louder than usual Possible fault Solution There could be pebbles within the coffee beans Turn off the unit immediately Contact the Miele s Tech Service if the bean container is not empty Otherwise fill the container with fresh beans The coffee espresso flows too fast into the cup Possible fault Solution The grind control is set too coarse Set the grind control slide to a finer grind The coffee espresso flows too slow into the cup Possible fault Solution The grind control is set too fine Set the grind control slide to a coarser grind 57 Frequently asked questions The coffee espresso is not hot enough Possible fault Solution Were the supply lines and cup The smaller the cup the more pre heat
64. ver at the lower rear side of the coffee machine m Screw the supplied brass compression fitting with the 34 end tightly onto the water connector of the coffee machine Tighten the compression fitting by hand do not use a tool The fitting includes an opening for standard 1 4 piping m Connect the compression fitting to the water supply m Check for leaks 69 Electrical connection WARNING Make sure that the power to the THIS APPLIANCE MUST BE machine is OFF before installing or GROUNDED performing maintenance or repairs Important All electrical work should be performed by a qualified electrician in strict accordance with national and local safety regulations Installation repairs and other work by unqualified persons could be dangerous The coffee system comes equipped with a 6 ft 1 8 m power cord with a NEMA 5 15P molded plug for connection to a 120 V 15 A 60 Hz power supply Verify that the voltage load and circuit rating information found on the data plate match the household electrical supply before installing the coffee System Do not connect the appliance to a power inverter or directly to power produced outside of the normal electrical grid i e direct solar or wind power source Direct connection to such power Sources can cause power surges and tripped breakers when the appliance is turned on and could damage the appliance Do not connect the appliance to energy saving
65. y that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts Only genuine Miele parts installed by factory trained professionals can guarantee the safety reliability and longevity of your Miele appliance Please note that unless expressly approved in writing by Miele s Service department Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele Our goal is to prevent unauthorized and untrained service personnel from working on your Miele products possibly doing further damage to them you and or your home To learn more about MieleCare Extended Service Contracts please contact your appliance dealer or visit us online at http mieleusa com mielecare ser Installation instructions Information is subject to change Please refer to our website to obtain the most current product specification technical amp warranty information Caring for the environment Disposal of packing material The cardboard box and packing materials protect the appliance during shipping They have been designed to be biodegradable and recyclable Please recycle Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of children Danger of suffocation 68 Disposal of an old appliance Old appliances may contain materials that can be recycled Please contact your local recycling authority about the po

Miele CVA 4066 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents