Home

M-Audio 61 User's Manual

1. Powered Monitors Computer Example Setup 2 Example Setup 2 shows a drum machine plugged into the Aux inputs and the ProKeys Sono main outputs plugged into a pair of powered speakers The ProKeys Sono MIDI Output jack is connected to the MIDI input of the drum machine while a sequencing application on a computer handles audio and MIDI data through the USB connection see Using ProKeys Sono with a Computer to learn more about how your ProKeys Sono and computer exchange audio and MIDI data This setup allows you to 1 Send MIDI information from either the ProKeys Sono keyboard or your computer s sequencer to the drum machine 2 Return the audio output of the drum machine into ProKeys Sono where it can be mixed with the built in sounds and or audio coming from the computer 3 The mixed output is then sent to powered speakers or headphones for monitoring About the audio inputs Keep in mind that ProKeys Sono features a 2 input 2 output audio interface This means that while ProKeys Sono has a variety of analog inputs on its rear panel i e an XLR microphone input a 1 4 instrument input and a pair of RCA Aux inputs the XLR Left Aux and Instrument Right Aux inputs are merged or summed together before being sent to the computer In other words if signal is present at all of the inputs when you begin recording the XLR and Left Aux will appear mixed together in channel one of your software while
2. 96 Data Increment 97 Data Decrement M AUDIO ProKeys Sono 61 User Guide 45 Appendix D Additional RPN Messages You may have noticed that although we have stated there are 128 MIDI controller messages 0 127 Appendix C shows 132 assignable controller messages This is because messages 128 131 are a different type of MIDI message defined in the MIDI Specification as RPN messages M Audio has created four messages that are sent like MIDI CCs but actually transmit a series of RPN messages This makes sending these complex multi part messages as easy as sending a MIDI CC message You can assign these to the controls on your ProKeys Sono keyboard in exactly the same way as any other MIDI controller message The RPN messages control the following Controller Number MIDI Message Use 128 Pitch Bend Sensitivity Alters the range of a pitch bend message 129 Fine Tune Adjusts the tuning of your sound module or synthesizer in small steps 130 Coarse Tune Adjusts the tuning of your sound module or synthesizer in large steps 131 Channel Pressure Adds an effect such as vibrato or brightness depending on the instrument settings and capabilities 15 Channel Pressure is not an RPN message However it is an additional effect message defined in the General MIDI specification and this is why we have included it in Appendix D Appendix E Piano Reset Button When the Piano R
3. 2 022020 ee 38 Program amp Bank Changes sa 44 saa a TEGENE a ee eae h k paaa a 38 NRPN RPNS ene bane any o oa oe MAA a ee le be AA e e e ea 39 Troubleshooting eee 40 Appendices Useful MIDI Data o o oo cocoa 42 Appendix A General MIDI Instruments LL 42 Appendix B Channel 10 Drum Map LL 43 Appendix C Standard MIDI Controller Numbers MIDI COS LL 44 Appendix D Additional RPN Messages LL 45 Technical SPSCHICAIONS erre I E AAA EA 46 DE ap er Ag 1 POE aaa aes eee Se ER eee EEE AAA 47 Waranty iia aa ao rra A a 47 M AUDIO ProKeys Sono 61 User Guide 3 Introduction Congratulations on your purchase of M Audio ProKeys Sono 61 ProKeys Sono 61 is a semi weighted velocity sensitive 61 key digital piano USB compatible MIDI controller and an audio interface in one convenient package Play the on board premium keyboard sounds as a standalone instrument or plug a microphone and guitar into ProKeys Sono and record edit and produce your performance via your computer utilizing the included recording software ProKeys Sono provides everything to instantly transform your computer into a versatile music studio ProKeys Sono functions as a class compliant device when connected to your computer via USB This means your computer will recognize the keyboard without the need to install additional drivers and will have immediate access to all audio inputs and outputs as well as to the built
4. 0 00000000 ce 14 ProKeys Sono Setup in Mac OS XX 15 Using ProKeys Sono with a Computer 16 Audio Tracks s oe ecs eosa aoaaa ee ke RRR RRR RE eee eee eee eee A Pew eee 16 MIDITMCKS e o ke ke 08s a ae Oa a a le a a ee eee ee we PAP ee ee wo 20 ProKeys Sono Audio Setup and ConmtrolS o oo es 23 Using the Microphone and Instrument Inputs ee 23 SeHiNginpitGaln e i FEE GP ead ooh Gh oth ae A 23 Wsingithe AUX NOUS sninen ud 20d 18 kr onda o a G a ee ACACIA E 24 Using Direct MONIGHING s e aa ee ae ee eR OR eh ee ew e ee new eg nn 24 The Mono Button sa s gt a LEA ewe es ee ERR a ee Be eR ee ee As ee ee ee T 25 The ProKeys Sono Audio Control Panel Windows Only 26 Latenoy s ok i E TR RE EEE ERE 26 ADOUE lt a aria e SDS ee 26 M AUDIO ProKeys Sono 61 User Guide Routing MIDI Data to and from your Computer 27 Routing MIDl Signals to your Software e s s sa Sa saka ee a a da i A RAEE EG 28 Routing MIDI Signals from your Software doa Da dok bi woe e e e e a e a e a aa 28 Advanced ProKeys Sono Functions in Edit Mode 29 Audio Options in Edit Modes sa sa sa sa Se ae KES SE GE SE GER EEE ee EEE I 29 Button Knob Wheel and Pedal Jack Assignments Lee 30 ProKeys MIDI Output Settngs 22 52 54 jek ks kors go ae kos a he ah od de r ee we ee es a A a 35 Sending a Bank Change or Program Change Message rak 37 MIDI Messages In Depth
5. NOTE If the Mono button on the top panel is disengaged this option does not have an impact on the signal path of audio being recorded M AUDIO ProKeys Sono 61 User Guide 30 USB Record Key This setting determines whether or not the internal ProKeys Sono voices will be sent to the computer for recording along with signals from all audio inputs By default audio recordings made using ProKeys Sono will include the internal instrument sounds if any of its sounds are playing during the recording process Pressing the D 1 key in Edit mode disconnects the internal sounds from the USB connection to the computer and prevents the keyboard s internal voices from being recorded along with signals from the audio inputs In other words the internal sounds will still be heard out of the main outputs but these sounds will not be sent to the computer through the USB connection to be recorded Pressing the D 1 key toggles the USB Record setting and exits Edit mode Repeating this process again toggles the USB Record setting back to its default state Button Knob Wheel and Pedal Jack Assignments Data Octave button Assignment Overview The Data lt and gt buttons can be assigned to control one of seven possible MIDI functions m Octave ProKeys Sono 61 Default m Transpose m Program Change Bank LSB m Bank MSB m MIDI Channel m Master Tune Setting In the diagram above there is a group of seven black keys labe
6. Please keep in mind that the red LED indicates that your input is clipping distorting digitally This is not the same kind of analog style distortion found on guitar amplifiers and stomp boxes Digital distortion is generally considered to be harsh and unmusical and it is recommended that you use the signal peak LEDs to avoid this type of clipping Windows XP Vista Users In Windows XP ProKeys Sono will appear as USB Audio Device if the optional drivers have not been installed If the drivers have been installed ProKeys Sono will appear as ProKeys Sono 61 In Windows Vista ProKeys Sono will appear as ProKeys Sono 61 regardless of whether or not the optional drivers have been installed Note that the actual ProKeys Sono name displayed by the computer may vary slightly Tip As described in the About the audio inputs box in the Hardware Connections chapter earlier in this User Guide the XLR Left Aux inputs and Instrument Right Aux inputs are merged or summed As a result if you are not using one of the inputs be sure to turn its gain knob all the way down fully counter clockwise since any possible background noise or unintended signals entering the unused input during recording may also be amplified and heard in the recording M AUDIO ProKeys Sono 61 User Guide Using the Aux Inputs M Audio ProKeys Sono has a pair of line level inputs labeled Aux In
7. 15 Dulcimer Organ 16 Drawbar Organ 17 Percussive Organ 18 Rock Organ 19 Church Organ 20 Reed Organ 21 Accordion 22 Harmonica 23 Tango Accordion Guitar 24 Nylon Acoustic Guitar 25 Steel Acoustic Guitar 26 Jazz Electric Guitar 27 Clean Electric Guitar 28 Muted Electric Guitar 29 Overdrive Guitar 30 Distorted Guitar 31 Guitar Harmonics 14 These sounds are ProKeys Sono premium quality voices Bass 32 Acoustic Bass 33 Electric Fingered Bass 34 Electric Picked Bass 35 Fretless Bass 36 Slap Bass 1 37 Slap Bass 2 38 Synth Bass 1 39 Synth Bass 2 Strings Orchestra 40 Violin 41 Viola 42 Cello 43 Contrabass 44 Tremolo Strings 45 Pizzicato Strings 46 Orchestral Harp 47 Timpani Ensemble 48 String Ensemble 1 49 String Ensemble 2 Slow 50 Synth Strings 1 51 Synth Strings 2 52 Choir Aahs 53 Voice Oohs 54 Synth Choir 55 Orchestral Hit Brass 56 Trumpet 57 Trombone 58 Tuba 59 Muted Trumpet 60 French Horn 61 Brass Section 62 Synth Brass 1 63 Synth Brass 2 Reed 64 Soprano Sax 65 Alto Sax 66 Tenor Sax 67 Baritone Sax 68 Oboe 69 English Horn 70 Bassoon 71 Clarinet Pipe 72 Piccolo 73 Flute 74 Recorder 75 Pan Flute 76 Bottle Blow 77 Shakuhachi 78 Whistle 79 Ocarina Synth Lead 80 Synth Square Wave 81 Synth Sawtooth Wave 82 Synth Calliope 83 Synth Chiff 84 Synth Charang 85 Synth Voice 86 Synth Fifths Sawtooth Wave 87 Synth Brass amp Lead Synt
8. section of this User Guide for information on how to change the operation of this button Direct Monitor Knob Direct Monitor The Direct Monitor knob controls the amount of audio input signal flowing from the Microphone Instrument or Auxiliary inputs directly to the 1 4 main outputs This allows you to monitor your inputs with near zero latency Piano Reset Button Piano Reset This button restores basic piano and keyboard controller functions including resetting the Modulation wheel Voice Volume knob and Sustain Pedal to their default settings This is useful in situations in which a user has changed settings of ProKeys Sono and would like to quickly return to the default state i e the Local Mode setting is set to On and the ProKeys Sono Grand Piano sound is loaded Pressing the Piano Reset button also sends a MIDI Panic sequence of commands i e All Notes Off and Reset All Controllers MIDI messages on MIDI channel 1 a useful feature if you experience stuck MIDI notes For a complete list of MIDI messages that are sent when this button is pressed see Appendix E Piano Reset Button Voice Volume Knob Voice Vol This is an assignable controller that by default controls the volume of the sounds built into ProKeys Sono Details on how to change the function of this knob can be found in the Knob Assignment portion of the Advanced ProKeys Sono Functions in Edit Mode section of th
9. Available Pre amp Gain Instrument Input 41 dB Input Impedance 1M Ohm unbalanced Maximum Input Level at minimum gain 12 dBV 4 Vrms SNR 94 dB A weighted Dynamic Range 94 dB A weighted THD N 0 00782 82 1 dB 1 dBFS 1 kHz Frequency Response 20 Hz to 20 kHz 0 6 dB Available Pre amp Gain Aux Inputs 40 dB Input Impedance 10K Ohm unbalanced Maximum Input Level 2 dBV unbalanced SNR 96 dB A weighted Dynamic Range 96 dB A weighted THD N lt 0 005 86 dB 1 dBFS 1 kHz Frequency Response Line Outputs 20 Hz to 20 kHz 0 5 dB Output Impedance 240 Ohm unbalanced Maximum Output Level 1 8 dBV 1 2 Vrms Channel to Channel Crosstalk lt 88 dB 1 kHz SNR 103 dB A weighted Dynamic Range 95 dB A weighted THD N 0 00391 88 2 dB 1 dBFS 1 kHz Frequency Response Headphone Outputs 20 Hz to 20 kHz 0 1 dB Maximum Output 2 dBV 0 8 Vrms into 32 ohms lt 0 05 THD N 18 2 mW into 32 ohms lt 0 05 THD N Working Range 32 to 600 ohms Frequency Response 20 Hz to 20 kHz 1 3 dB M AUDIO ProKeys Sono 61 User Guide Technical Info Caution Electro Static Discharge Electrical Fast Transient and Conducted RF interference may cause the unit malfunctioning In such case unplug the unit and plug it in agai
10. Inst Gain This knob controls the gain level of the Instrument input The signal green LED illuminates when signal is present at the instrument input i e incoming audio signal is greater than 20dB The peak red LED illuminates when incoming audio signal is clipping distorting and indicates that the Instrument Gain knob should be turned down Mono Button Mono By default this button affects how incoming signals from the Microphone Instrument and Auxiliary inputs are heard through your speakers or headphones When active any input signal will be routed to both the left and the right side of your stereo speakers or headphones in equal amounts making them appear centered in the stereo field Note that by default the Mono button only affects what you hear In other words when recording while the Mono button is active the signals from the Microphone Instrument and Auxiliary inputs are still sent to your computer in separate left and right channels meaning the Microphone will appear on the left channel and Instrument on the right channel within your recording software the left and right channels of your Auxiliary inputs will appear in the left and right channels of your software respectively Also note that the function of the Mono button can be changed to allow incoming signals to be recorded exactly as they are heard while monitoring See the MONO Input Record Key portion of the Advanced ProKeys Sono Functions in Edit Mode
11. all MIDI channels This lets you immediately stop stuck notes and remove applied MIDI CC effects without having to figure out what has caused the unexpected changes in your sound To send a Panic MIDI message 1 Press the Edit Mode button 2 Press the black key above F3 F 3 representing Panic 3 Edit mode will exit and sustaining notes will stop playing Sending a Bank Change or Program Change Message PROGRAM CHANGE Sending a specific program change message is useful if you want to load a particular sound patch TIP As an example let s use a program To send a specific program change message in Edit mode change MIDI message to activate the internal cello sound on ProKeys Sono To do this we 1 Press the Edit Mode button need to send program change number 42 this 2 Press the black key above F5 F 5 representing corresponds to a cello sound in the General Program MIDI Instruments list in Appendix A 3 Press the number keys G4 through B5 that 1 Press the Edit Mode button correspond to the program number you wish 2 Press the black key above F5 F 5 representing Program to load 4 Press C6 Enter ProKeys Sono will exit Edit mode as soon as a C6 has been pressed 3 Press keys D5 then B4 then C6 Enter This enters the combination 4 2 BANK CHANGE ENTER Sending a specific bank change message is useful if you want to i This message will be sent to the Pr
12. allows for program change commands 0 1 27 for a total of 128 possible programs 127 programs program 0 128 programs total Because of inherent limitations of the MIDI communication protocol the number of directly accessible programs using program change messages cannot easily be expanded beyond 128 Thus a system of banks with 128 sounds in each has been created that enables manufacturers to overcome the sn Bank MSB Bank LSB Program 128 sound MIDI limit _ 2 TT 128 banks with 128 sounds in each bank is the Program 0 i EE P 7 basic principle used to expand the number of 7 accessible sounds However to avoid reaching i the new limit of the resulting 16 384 possible TEO sounds 128 banks x 128 programs accessible mami A A rogram using a bank change combined with a program gt i change another layer of banks was added The i o i Smal P result is a system of 128 banks that can contain i SI Ion 128 sub banks in each of them which in turn i i aoon can contain 128 sounds programs within them i Bank change messages are useful when calling i up sounds from a large library that may exist in a i GE i 1 particular sound module or software synthesizer i LAA For example devices that are built according i Bse TT AR to Roland s GS specification or Yamaha s XG specification require you to specify a bank Bank MSB1 fpi Bank 155 1 EE change in order to access the extra voices that s
13. always consists of items 1 5 listed above for all MIDI notes MIDI instructions can be recorded by software and simultaneously routed to destinations that will transform the data into actual sound the built in sounds on ProKeys Sono a virtual instrument running on the computer or an external MIDI synthesizer As you begin using ProKeys Sono you will quickly discover that using a computer based sequencer with virtual instrument software gives you access to a large array of high quality sounds a large graphic user interface and the ability to edit and change performances even after they ve been recorded M AUDIO ProKeys Sono 61 User Guide Routing MIDI Signals to your Software Most recording applications require you to select the MIDI input device that you wish to use To do this navigate to the appropriate MIDI setup menu within your music software and select ProKeys Sono as the MIDI input device The exact name and location of the MIDI setup menu varies among different sequencing applications but it is often found under the setup or preferences menu See your specific application s documentation to learn more about MIDI input configuration 10 Note that the actual ProKeys Sono name displayed by the computer may vary slightly Attention Windows Users Under Windows XP ProKeys Sono will appear as USB Audio Device if the optional drivers have not been installed and ProKeys Sono 61 if the optional drivers
14. buffer sizes result in lower latency but may not function well with slower computer systems The Latency slider selects the buffer size that ProKeys Sono uses to handle digital audio streaming If you notice significant latency when using ProKeys Sono you can experiment with lower settings If you experience stuttering or crackling in your audio playback try using a higher latency setting Use the slider to adjust the buffer size to the lowest possible setting that still provides error free recording and playback To find your system s optimum buffer size setting begin with a high setting and gradually reduce the size until you begin to hear clicks pops or other audible glitches in your audio Then raise the buffer size setting until these glitches disappear You may need to stop playing audio any time you change this setting and certain applications will require you to re launch the program before the new buffer size settings become active About This tab displays the ProKeys Sono Control Panel firmware and driver version and allows you to connect to the M Audio website for updates M AUDIO ProKeys Sono 61 User Guide Routing MIDI Data to and from your Computer If you are new to MIDI it may be challenging to understand how your computer and ProKeys Sono talk to each other using MIDI as the communication protocol The fundamental principle to understand is that MIDI is a control protocol a MIDI connection allows instruct
15. cards are not supported M Audio suggests you also check the minimum system requirements for any software applications you plan on using with your new M Audio hardware as they may be greater than the above gt IMPORTANT Connect your headphones or powered speakers to ProKeys Sono Sounds created by ProKeys Sono and from software used with it will play through the main outputs on ProKeys Sono not the outputs of your computer s built in soundcard A Note About System Updates Please check the M Audio driver download page at http www m audio com drivers for the availability of an updated driver before you decide to install operating system updates Before new M Audio device drivers are released they are tested for use with the operating system versions that are available at that time When updates for an operating system are released by Microsoft or Apple all M Audio device drivers have to be re tested and possibly updated to ensure proper operation M Audio recommends refraining from installing operating system updates until a driver has been posted to the M Audio website for that specific operating system M AUDIO ProKeys Sono 61 User Guide Controls and Connectors Top Panel Diagram 6 7 8 9 10 1112 13 14 15 Top Panel Descriptions 1 Modulation Wheel Modulation This wheel is used to add expressivity to your performance by changing the intensity of certain effects The Modulation wheel usually controls vibrato
16. change in intonation or tremolo change in volume of your selected sound The MIDI data range of this wheel is O to 127 with O being the note unchanged position i e the wheel is rolled downward toward the user Note that the Modulation wheel can be assigned to control MIDI parameters other than modulation MIDI CC 1 This topic is covered in the Advanced ProKeys Sono Functions in Edit Mode chapter of this User Guide Headphone Outputs Phones These two output jacks accept standard 1 4 headphones The volume of these outputs is controlled by the Master Volume fader 6 Pitch Bend Wheel Pitch Bend This wheel lets you create expressive changes in your performances by raising and lowering pitch Rolling the Pitch Bend wheel upward will raise an instrument s pitch whereas rolling it downward will lower the pitch Note that this wheel is spring mounted and will return to the center position when released Octave Shift Data lt gt Buttons In this User Guide these buttons will be referred to as the Data buttons By default these buttons shift the center of the keyboard in one octave increments Pressing the Data gt button right will shift the notes played on the keyboard up one octave for example D2 becomes D3 When shifted upward the LED above the right Data button will illuminate Pressing the Data lt button left will shift the notes played on the keyboard downward for example G4 becomes G3 and the LED abov
17. file from the desktop Mac OS X 10 4 to display its contents Next double click the installer application 2 Follow the driver installer s on screen instructions During Installation Mac OS X will ask you to enter your user name and password Enter this information and click OK to confirm If you have not configured a password for your computer leave the password field blank and click OK If you are not the computer s owner ask the owner or your Administrator for the missing information Authenticate PR Installer requires that you type your password Name Password Cancel OK 3 When the installer has completed click Restart Your computer will reboot automatically 4 After your computer has finished starting up connect ProKeys Sono to an available USB port on your computer The single USB cable not only powers the keyboard but also transfers MIDI and audio data to and from your computer system ProKeys Sono is now ready to use M AUDIO ProKeys Sono 61 User Guide Using ProKeys Sono with a Computer ProKeys Sono provides an array of features and a multitude of possibilities when used in conjunction with recording software on your computer As described earlier in this guide ProKeys Sono combines the functionality of several devices in one single product These features can interface with computer software in many different ways Recording software typically provides different types of tracks allowi
18. have been installed In Windows Vista ProKeys Sono will appear as ProKeys Sono 61 regardless of whether or not the optional drivers have been installed Once ProKeys Sono is selected as the MIDI input device most applications will automatically route MIDI data from ProKeys Sono to the record enabled track unless you explicitly specify a different routing This means you can record enable your preferred MIDI track start recording in your sequencer and play your ProKeys Sono keyboard Your performance will be recorded by the application Refer to your sequencing application s documentation to learn more about the specifics of recording MIDI within that program Routing MIDI Signals from your Software Your ProKeys Sono will appear as two separate MIDI output ports in your sequencing application Selecting ProKeys Sono Voices will send your MIDI data to the ProKeys Sono internal sound engine whereas selecting ProKeys Sono MIDI Out will send that MIDI data to the MIDI output jack on the rear of the keyboard Sending MIDI to the ProKeys Sono sound engine ProKeys Sono contains a complete GM sound set containing 128 voices five of which are the ProKeys Sono premium quality voices Select e ProKeys Sono 61 or USB audio device as the MIDI output hardware device within your recording software s MIDI setup options ProKeys Sono Voices or USB audio device as the MIDI output port of the specific MIDI track you r
19. lf you have not done so already try installing the ProKeys Sono drivers to see if this problem resolves If this does not resolve the issue Open the Control Panel and double click the System icon under Performance and Maintenance if you are in Category view e Select the Hardware tab and click the Device Manager button e Click the plus sign next to Sound Video and Game Controllers and locate the ProKeys Sono listing If you see a question mark or exclamation point next to it or if you don t see it listed you may need to reinstall the driver software e Make sure your audio software has been configured to use ProKeys Sono This configuration process varies from application to application but it is usually done through a preferences or configuration menu See your application s documentation to learn more about this Problem cannot hear the internal sounds of ProKeys Sono when using the keyboard with a computer based sequencer in Local Off mode Solution This behavior is normal Local Off mode interrupts the connection between the internal sound engine and the various MIDI controls i e the keys wheel knob etc of ProKeys Sono If you are using ProKeys Sono with a software sequencer and would like to play the internal sounds of ProKeys Sono make sure that the software sequencer s track that is recording MIDI data from the keyboard is sending that MIDI data back to the ProKeys Sono Voices MIDI outp
20. of the two ProKeys Sono MIDI output ports when working with virtual instruments Configure your sequencing application to route MIDI signals to your virtual instrument software 5 ProKeys Sono will appear as two separate MIDI output ports within your sequencing application ProKeys Sono MIDI Out and ProKeys Sono Voices or when using the device class compliant in Windows XP as USB Audio Device and USB Audio Device 2 See the section titled Routing MIDI Signals from your Software for more information M AUDIO ProKeys Sono 61 User Guide Recording MIDI and triggering the internal sounds of ProKeys Sono da Note Most MIDI recording xy m a applications allow incoming MIDI signals to be recorded and simultaneously passed through to oipny 110 externally connected MIDI devices 3NO oipny If your software is configured to do this and you are working with the gt S 2 2 built in voices of ProKeys Sono sounds will be triggered in real time an0 olpny through the recording software However by default ProKeys Sono MIDI ProKeys 5 AE via Sono also triggers its built in sounds USB Voices port directly when playing the keys on the keyboard This means that you may hear every note twice Once Recording Software since the sounds are triggered locally from the ProKeys Sono MIDI via USB keyboard and a second time because of MIDI signals returning t
21. only the program change MIDI command is limited to 128 0 127 Since some devices have more than 128 voices they require a method to organize their large number of sounds into banks Such devices use Bank LSB Least Significant Byte and or Bank MSB Most Significant Byte change messages to select between groups of sounds banks These devices then access the sounds within these banks by using program change messages See the MIDI Messages In Depth chapter of this User Guide for additional information The Data lt and gt buttons can be assigned to send incremental Bank LSB or Bank MSB messages To assign the Data lt and gt buttons to send bank change messages 1 Press the Edit Mode button 2 Press the black key above G2 G 2 or A2 A 2 representing Bank LSB or Bank MSB respectively Now the Data lt and gt buttons can be used to send Bank LSB or Bank MSB change messages As with Program changes if the Data lt and gt buttons are selected to vary the Bank LSB or MSB number the LEDs above the buttons will not change since it is not possible to have a Bank with a negative value Pressing both the lt and gt buttons together will recall Bank 0 Bank 0 is the bank in which the internal ProKeys Sono sounds reside An additional method of sending Bank Change messages is described in the ProKeys MIDI Output Settings chapter of this User Guide 12 NOTE Bank change m
22. the Advanced ProKeys Sono Functions in Edit Mode chapter for additional information on this M AUDIO ProKeys Sono 61 User Guide The ProKeys Sono Audio Control Panel Windows Only The M Audio ProKeys Sono Control Panel gives you access to certain audio hardware parameters and status displays When the ProKeys Sono drivers are installed the Control Panel software is also installed onto your system The ProKeys Sono Control Panel icon i appears in both the system tray near the clock and Windows Control Panel Double click the icon to open the ProKeys Sono Control Panel M Audio ProKeys Sono 61 Properties connected Latency is a measure of the delay between the time you make a sound and the time the computer records or monitors that sound Here the unit for latency is the number of samples the driver collects before sending them to an application as input Lower latency can make recording easier and more accurate but not all computer systems can operate at the lowest latencies without introducing noise If you experience unwanted input noise increase latency Latency Latency is defined as the time it takes for audio to pass through your computer and appear at the outputs of ProKeys Sono This parameter also adjusts the amount of latency when using virtual instrument software on your computer Please see your virtual instrument software s documentation to learn more about this Smaller
23. the Using Direct Monitoring section in the ProKeys Sono Audio Setup and Controls portion of this User Guide to learn more about direct monitoring Problem have connected the keyboard to my computer with the USB cable but I cannot locate the ProKeys Sono USB keyboard in my software s MIDI devices dialog box Solution 1 ProKeys Sono may not be receiving enough USB bus power to function correctly Try plugging Prokeys Sono into a different USB port or a powered USB hub connected to your computer Solution 2 In Windows XP ProKeys Sono will appear as USB Audio Device if the optional drivers have not been installed Select USB Audio Device as your audio and MIDI input and output device Problem connected ProKeys Sono to my Windows computer and noticed that a question mark appears in the Windows Device Manager under Other Devices gt M Audio DFU Does this indicate that there is a problem with Prokeys Sono Solution This behavior is normal and your ProKeys Sono will function normally as a class compliant device i e without any drivers Installing the ProKeys Sono drivers extends the keyboard s functionality in various ways i e multi client support support for qualified versions of the Pro Tools M Powered software and allowing large SysEx transfers and should resolve any DFU related messages that appear when drivers are not present Problem My synthesizer always recalls the sound next to the program num
24. the Instrument and Right Aux inputs will appear mixed together as channel two Note that by default the built in ProKeys Sono sounds are also summed with the microphone instrument and auxiliary inputs and sent to the computer for recording If you do not wish to send the ProKeys Sono sounds to your music software this can be accomplished by toggling the USB Record switch in Edit mode Additional information on this can be found in the USB Record Key portion of the Advanced ProKeys Sono Functions in Edit Mode chapter of this User Guide Similarly while ProKeys Sono features two sets of headphone outputs and 1 4 main outputs all of these outputs play the same stereo signal M AUDIO ProKeys Sono 61 User Guide ProKeys Sono as a Standalone Instrument Standalone operation refers to using ProKeys Sono without a computer To do this an optional USB type power supply or 9V 500mA center positive power supply sold separately is required NOTE While ProKeys Sono can receive power from two different power sources the device only requires one power source to operate In other words if one type of power supply is connected such as a USB type power adapter it is not necessary to connect the second type of power supply the 9V 500mA adapter ProKeys Sono can function as a standalone instrument providing five premium voices and a complete General MIDI GM sound set In addition to playing the built in sounds you can use
25. the USB cable it is security cables to protect your device from theft not necessary to use a DC power supply M AUDIO ProKeys Sono 61 User Guide Hardware Connections Audio Inputs A dynamic microphone can be connected to the XLR input on the rear panel of the keyboard while an instrument such as a guitar or bass can be connected to the 1 4 input jack next to the XLR input Each of these two inputs has an independent preamp with its own gain control knob and signal clip LEDs Two RCA Auxiliary inputs are also located on the back panel Signal from these inputs is mixed with the Microphone and Instrument inputs before being routed through the USB connection to a connected Mac or PC Audio Outputs Connect the two 1 4 main outputs on the rear panel to powered monitors an amplifier or a mixer You may also monitor through headphones by connecting one or two sets of headphones to the 1 4 stereo headphone outputs on the front panel MIDI Connections In addition to the USB MIDI connection between ProKeys Sono and your computer you can connect the MIDI Out jack of ProKeys Sono to an external device s MIDI input This allows you to control an external synthesizer or sound module by either using ProKeys Sono as a standalone MIDI controller keyboard or by sending your sequencing application s MIDI data to the hardware device through the keyboard i e using ProKeys Sono as a USB to MIDI interface Note that the ProKeys Sono
26. the keyboard to trigger sounds on synthesizers or sound modules that are connected to the MIDI Out jack on ProKeys Sono By default ProKeys Sono transmits MIDI data on channel one You can also use the Mic Gain Instrument Gain Direct Monitor and Voice Volume knobs in standalone mode to create a mix of your keyboard guitar and vocal performances ProKeys Sono Premium Voice Selection The five premium voices can be accessed via the Voice Select buttons on the top panel Pressing one of these buttons activates the corresponding sound ProKeys Sono GM sound selection The ProKeys Sono keyboard has a full General MIDI GM sound set with 128 sounds built in The built in GM sounds can be accessed in two ways Method 1 Recall a specific General MIDI instrument in Edit mode Appendix A lists the built in General MIDI instruments by their sound numbers Access a specific instrument by entering its number in Edit mode 1 Press the Edit Mode button 2 Press the black key above F5 F 5 representing Program 3 Enter the desired program number using the white keys between G4 and B5 4 Press C6 Enter to confirm the selection Method 2 Browse General MIDI instruments using the Data buttons Reassigning the Data buttons to send program change messages will allow you to step through and audition the built in General MIDI sounds in consecutive order To configure the Data lt gt buttons to send program change messages 1 Press th
27. without installing drivers the computer will search for the M Audio DFU device firmware upgrade tool and display a Found New Hardware Wizard The M Audio DFU is a component of ProKeys Sono 61 that is enabled when the M Audio drivers are installed but is not necessary for class compliant operation As a result the Found New Hardware Wizard and can safely be ignored in this scenario See page 14 to learn more about this topic M AUDIO ProKeys Sono 61 User Guide a ProKeys Sono 61 Features Keyboard Bu m 61 semi weighted velocity sensitive keys n m 5 high quality voices Grand Piano Bright Piano Electric m Piano Organ Clavinet General MIDI GM sound set with a total of 128 built in sounds for playback of MIDI files On board reverb and chorus effects Pitch Bend wheel Modulation wheel MIDI re assignable Voice Volume knob MIDI re assignable Octave up down buttons MIDI re assignable Sustain pedal input MIDI re assignable MIDI output jack 40 note maximum polyphony Edit mode for advanced functions and programming Bus powered through USB or DC power for standalone functionality DC power adaptor sold separately Class compliant operation no driver installation required simply connect the keyboard and power on ilt in Audio Interface 16 Bit 44 1 kHz 2 in 2 out audio interface XLR microphone input 1 4 instrument input and stereo RCA inputs Two rear panel 1 4 main outputs Two fro
28. 1 Ride Cymbal 1 75 Claves 52 Chinese Cymbal 76 Hi Wood Block Ride Bell Low Wood Block Tambourine Mute Cuica 55 Splash Cymbal 79 Open Cuica 56 Cowbell 80 Mute Triangle 57 Crash Cymbal 2 Open Triangle Vibraslap M AUDIO ProKeys Sono 61 User Guide Appendix C Standard MIDI Controller Numbers MIDI CCs 00 Bank Select 49 Gen Purpose 2 LSB 98 NRPN LSB 01 Modulation 50 Gen Purpose 3 LSB 99 NRPN MSB 02 Breath Control 51 Gen Purpose 4 LSB 100 RPN LSB 03 Controller 3 52 Controller 52 101 RPN MSB 04 Foot Control 53 Controller 53 102 Controller 102 05 Portamento Time 54 Controller 54 103 Controller 103 06 Data Entry 55 Controller 55 104 Controller 104 07 Channel Volume 56 Controller 56 105 Controller 105 08 Balance 57 Controller 57 106 Controller 106 09 Controller 9 58 Controller 58 107 Controller 107 10 Pan 59 Controller 59 108 Controller 108 11 Expression 60 Controller 60 109 Controller 109 12 Effects Controller 1 61 Controller 61 110 Controller 110 13 Effects Controller 2 62 Controller 62 111 Controller 111 14 Controller 14 63 Controller 63 112 Controller 112 15 Controller 15 64 Sustain Pedal 113 Controller 113 16 Gen Purpose 1 65 Portamento 114 Controller 114 17 Gen Purpose 2 66 Sostenuto 115 Controller 115 18 Gen Purpose 3 67 Soft Pedal 116 Controller 116 19 Gen Purpose 4 68 Legato Pedal 117 Controller 117 20 Controller 20 69 Hold 2 118 Controller 118 21 Controller 21 70 Sound Variation 119 Controller 119
29. 22 Controller 22 Channel Mode Messages 23 Controller 23 72 Release Time 120 All Sound off 24 Controller 24 73 Attack Time 121 Reset All Controllers 25 Controller 25 74 Cut off Frequency 122 Local Control 26 Controller 26 75 Controller 75 123 All Notes Off 27 Controller 27 76 Controller 76 124 Omni Off 28 Controller 28 77 Controller 77 125 Omni On 29 Controller 29 78 Controller 78 126 Mono On Poly Off 30 Controller 30 79 Controller 79 127 Poly On Mono Off 31 Controller 31 80 Gen Purpose 5 32 Bank Select LSB 81 Gen Purpose 6 Extra RPN Messages 33 Modulation LSB 82 Gen Purpose 7 128 Pitch Bend sensitivity 34 Breath Control LSB 83 Gen Purpose 8 129 Fine Tune 35 Controller 35 130 Coarse Tune 36 Foot Control LSB 85 Controller 85 37 Portamento Time LSB 86 Controller 86 38 Data Entry LSB 87 Controller 87 39 Channel Volume LSB 88 Controller 88 40 Balance LSB 89 Controller 89 41 Controller 41 90 Controller 90 42 Pan LSB 91 Reverb Depth 43 Expression LSB 92 Tremelo Depth 44 Controller 44 93 Chorus Depth 45 Controller 45 94 Celeste De tune 46 Controller 46 95 Phaser Depth 47 Controller 47 48 Gen Purpose 1 LSB 71 Resonance 84 Portamento Control 131 Channel Pressure
30. I Out jack on ProKeys Sono to give you even more sound choices Below we will examine various MIDI options you have with ProKeys Sono by looking at the different track types in a typical recording sequencing application and the options you have with each of them Recording MIDI and triggering sounds on a virtual instrument sons 1 O OO E o o o 9 se dal filo Recording Software MIDI via USB If Powered Monitors ProKeys Sono 61 TIP See your software s documentation to learn more about audio MIDI routing and virtual instruments Ne NOTE For additional information on routing MIDI signal from ProKeys Sono to your computer sequencing software see the Routing MIDI Data to your Computer section of this User Guide In this scenario the keys wheels and other controls of your ProKeys Sono generate MIDI data that is sent to the computer through the USB connection The computer s sequencing software routes this MIDI data to a virtual instrument loaded on one of its tracks The virtual instrument receives the MIDI data and then generates audio data sound that is then routed to the ProKeys Sono main outputs Monitoring can take place over powered speakers connected to the 1 4 main output jacks on the rear panel or by headphones connected to either one of the 1 4 headphone jacks on the front panel Note that it is not necessary to select any
31. IDI Out Mode setting has been left in its default setting MIDI data generated by playing the keys on the keyboard will be transmitted from the keyboard to the external MIDI output jack and also to your computer via USB This is the default setting for ProKeys Sono If the MIDI Out Mode setting has been configured to pass signals coming from your computer via USB the data coming from the host computer via USB will be sent directly to the MIDI Out jack In this mode MIDI data generated by playing the keys on the keyboard is not sent to the MIDI Output jack but only to the computer via USB In Edit mode when the MIDI Out Mode key G 3 is pressed the function is toggled and Edit mode is exited Pressing the Piano Reset button or turning the keyboard off and back on will restore the default setting 13 NOTE MIDI Out mode only affects signals sent from your computer s sequencing application to the ProKeys Sono MIDI Out port this mode does not affect MIDI data sent to the ProKeys Sono Voices port Local On Off The Local On Off Key A 3 determines the source of the data stream that is routed to the sounds built into ProKeys Sono By default notes played on the keyboard and notes received via USB from a connected computer are both routed to the ProKeys internal sound engine However pressing this key in Edit mode will set the Local On Off option to Off This causes the internal sound engine to no longer directly receive notes fr
32. M AUDIO roKeys Sono 61 User Guide GENERAL M AUDIO ProKeys Sono 61 User Guide piso 0 EEE ILS 3 ProKeys Sono 61 Features 4 Keyboard a coc econo eT EEE EE Oe EEE AAA 4 Butin Audio Interface 2 222228 2 485 5 BE EEE SSS AAA 4 Minimum Requirements 5 Standalone Operation UL ak AAA A EEEE EW OEE E O 5 Bus Fowered Operationy ase aesae a RARE eee eee FESTE See ees 5 Controls ana Connectors auauua aaaea een nh ehh hod FE EES PEG ees 6 Top Panel Diagram su vag saka va eee RE EEE SEER DE ee ee eee EEE EEE SE 6 Top Panel Descriptions 2 444444 4 245444 I eee ewe we GE GE GE RE eee SEES 6 Rear Panel Descriptions saa iii seas ee eels SENSE De De EE eee EEE EE EEG 8 Hardware WOnneciOnSs lt o 744c 5t6eeeee TATE LTT IRA AA 9 Audio puts vs cc RE A bud bed E PG EEE aa 9 AudioQuipuls ass sea ALLA Aa GENENE HAR 9 MIDI Connections o e dit i e RR ew RIE 9 Other Connections e lt e aa sag RR e e PE 9 Example Operating Scenarios n aa am RR RR 10 Aboutihe audiounputsi s s sa oe Se SEG ee ee E E EEE da be eee 11 ProKeys Sono as a Standalone Instrument 12 ProKeys Sono Premium Voice Selection we a a ee 12 ProKeys Sono GM sound selection wa cs ae a a AAA Se ee 12 ProKeys Sono as a Standalone Microphone Preamplifier and Mixer LL 13 Prokeys Sono Demos 4 ie daw ea aaa Ha Eade we eee ewe we eee GEE EEE Eo a ee 13 Basic ProKeys Sono Setup in Windows
33. MIDI Out Mode setting must be configured correctly for your sequencing application s MIDI output signals to appear at the MIDI output jack on the back of ProKeys Sono Please see the section entitled MIDI Out Mode Key in the ProKeys MIDI Output Settings chapter to find out more about this setting Other Connections A sustain pedal can be connected to the 1 4 Sustain pedal jack on the back of the keyboard M AUDIO ProKeys Sono 61 User Guide Example Operating Scenarios The following diagrams illustrate two scenarios in which ProKeys Sono is connected to external hardware Guitar O Mic ProKeys Sono back D E ng ABEIREUE Instrlfnent Miciphone Sustain MIDI Out egy SVDC O ord Om z I gt O Powered Monitors O fe ee CD Player Example Setup 1 Example Setup 1 shows M Audio ProKeys Sono with a microphone connected to the Microphone input and an electric guitar plugged into the Instrument input A CD player is connected to the auxiliary inputs The main outputs of ProKeys Sono are connected to a monitoring system powered speakers in this case while a computer powers the keyboard through the USB connection A sequencing application on the computer handles all incoming and outgoing audio and MIDI data This is covered in greater detail in the Using ProKeys Sono with a Computer section of this guide M AUDIO ProKeys Sono 61 User Guide
34. YYO ezed mo IGIW HO UO 122017 BARPO SALIDO UBISSY 398UM uBissy epad u6issy qouy asodsueii asodsueii weiboid 957 Xueg SSW 4Ueg fo z jo 3 3 D 5 MOT 2AUNI PA OIW SAND IPA IH SAIND PA asodsueii e3eG wes6oig e3eg asi 4ueg ejea gsw Mueg eeg jeuuey gt ezed Sun ejeg NOTE The M Audio ProKeys Sono Drivers and Documentation CD ROM contains a document showing a larger image of the keys and their advanced features in Edit mode called KeyMap61 pdf We recommend printing this document and keeping it with your ProKeys Sono for fast access to the advanced features in Edit Mode Audio Options in Edit Mode MONO Input Record Key This setting determines if the Mono button on the top panel of ProKeys Sono affects how input signals are recorded or only how they are heard while monitoring By default the Mono button only affects the monitor signal recordings remain unaffected Pressing C 1 in Edit mode and engaging the Mono button will cause all input signals to be merged before being sent to the computer for recording As a result identical signals will be recorded to the left and the right channel of a stereo track essentially creating a two channel Mono recording This feature is most useful when only one of the inputs of ProKeys Sono is used at a time e g the Mic input or the Instrument Input as it allows you to record a single channel signal to both channels of a stereo track
35. able on both headphone outputs and the rear panel 1 4 outputs Use the Master Volume slider to adjust the overall output level lt Tip Connect the MIDI Out jack of ProKeys Sono to an external MIDI synthesizer or sound module Connect the Line outputs of the external device to the Aux inputs on ProKeys Sono If you play the ProKeys Sono keyboard you will trigger MIDI sounds on the external MIDI synthesizer and can hear them back through the ProKeys Sono main outputs NOTE ProKeys Sono is capable of many advanced features which can be accessed via the ProKeys Sono Edit mode Many of these features can be useful when ProKeys Sono is operating in Standalone mode Additional information concerning these features can be found in the Advanced ProKeys Sono Functions in Edit Mode chapter of this User Guide ProKeys Sono Demos ProKeys Sono has a built in demo song for each instrument sound To hear these demos 1 Press the Edit Mode button 2 Press one of the Voice Select buttons Demo playback can be stopped by pressing the Edit Mode button While the demo is playing the LED of the selected voice will flash At the completion of the demo the demo song will repeat M AUDIO ProKeys Sono 61 User Guide Basic ProKeys Sono Setup in Windows Information on Windows driver installation can be found in the included printed Quick Start Guide Your computer will recognize ProKeys Sono without the nee
36. ai LT Program 2 7 bit message allowing additional selection of Sale do any of another 128 sub banks The combination i Bank LSB Q ne ae of Bank MSB and LSB messages gives a 14 bit BankMSB2 kl Bank LSB 7 ata message that can select any of a possible DJ Tre ja CUM ES 16 384 banks Each bank can in turn contain 128 I Bank TSB 2 TA 27 possible sounds selected via a separate program y i Si SSI Program 1 change MIDI message This enables a user to 3ank MSB 127 3ank LSB 127 theoretically recall over two million programs Y I these devices provide i PES i MIDI CC 0 is the bank select MSB Most i En Significant Byte message This MIDI message i i is 7 bit in size and can be used to select any i of 128 banks This message can be used in i conjunction with MIDI CC 32 which is bank i select LSB Least Significant Byte a separate i 720 Pregrami I i directly using only MIDI commands However most devices only use a few different banks and you can often ignore the LSB message M AUDIO ProKeys Sono 61 User Guide 39 You will find many MIDI devices respond to program change commands and many are organized according to the GM listing In General MIDI devices different sounds are organized in the same way from device to device Piano sounds are in their particular place string sounds are in their place drum sounds are in their place and so on All GM devices both hardware and software sound modules are clearly labeled as
37. ake use of software based monitoring Software monitoring allows you to hear your signals after they have passed through the recording software ProKeys Sono also features a Direct Monitor knob 10 that allows you to listen to input signals directly on the main outputs without passing the signals through your audio software This feature is covered in the Using Direct Monitoring section of the ProKeys Sono Audio Setup and Controls chapter M AUDIO ProKeys Sono 61 User Guide Recording from a Microphone to an Audio Track ano olpny ino opny no olpny ano olpny IGIW Powered Monitors ProKeys Sono 61 Microphone A 99000 0o00 Bo 00 In this scenario ProKeys Sono is being used as an audio interface to record a microphone The microphone s output signal is received at the microphone XLR input jack on ProKeys Sono and sent to the computer through the USB connection Sequencer software running on the computer can then capture the microphone signal on one of its mono audio tracks the track is labeled Mic in the illustration above This signal can be monitored while recording or played back after it has been recorded Monitoring can take place over powered speakers connected to the 1 4 main output jacks on the rear panel or by headphones connected to either one of the 1 4 headphone jacks on the front panel Keep in mind that depending on h
38. ber that have sent to it from ProKeys Sono For example if I send a program change with the number 40 Violin my software loads sound number 41 Viola Solution Some General MIDI modules count their sound patches from 1 128 instead of 0 127 Both methods are common As a result there may be an offset of 1 between the program change number sent from the keyboard and the recalled sound patch on your module M AUDIO ProKeys Sono 61 User Guide 41 Problem When press the keys or use any of the MIDI controls wheel knob data buttons etc no data is being transmitted from the MIDI output jack Solution This may be the result of the ProKeys Sono MIDI Out mode being set to USB The MIDI Out jack can be configured to accept MIDI data from either the ProKeys Sono keyboard or from the computer via the USB connection If the MIDI Out mode is set to USB the controls on the keyboard will not send any data to the MIDI Out jack See the ProKeys MIDI Output Settings chapter of this User Guide to learn how to toggle MIDI Out mode back to transmit MIDI events generated by the ProKeys Sono keyboard Alternatively you may simply switch the keyboard off and power it back on This will restore the default causing the MIDI output jack to transmit MIDI events generated by the ProKeys Sono keyboard Problem When using ProKeys Sono with Windows XP or Vista the computer plays no sound through the ProKeys Sono main outputs Solution
39. certain otherwise more complicated multi part MIDI messages A full list of controller values is given at the end of this manual in Appendix C For these controller values to have any effect on the sound the receiving software or device has to be able to read and respond to these MIDI controller messages Some examples of useful MIDI CCs are 01 Modulation m 07 Volume m 10 Pan balance m 05 Portamento Time To assign a MIDI controller message to the Modulation wheel 1 2 3 Press the Edit Mode button Press the black key above F4 F 4 representing Wheel Assign Use the Numerical Data Entry keys G4 B5 to enter the number of the MIDI controller you want to assign to the Modulation wheel Press the Enter key C6 If you make an error while entering the numerical data value you can press the CANCEL key C2 to exit Edit mode without changing the MIDI CC assigned to the Modulation wheel As an example let s assign MIDI CC number 10 to the Modulation wheel This means the Modulation wheel will control Pan or balance 1 2 3 4 5 Press the Edit Mode button Press the black key above F4 F 4 representing Wheel Assign Press A4 to enter 1 Press G4 to enter 0 so you have entered 10 Press C6 for ENTER To re assign the Modulation wheel to its default function f 2 3 Press the Edit Mode button Press the black key above F4 F 4 representing Wheel Assign Pr
40. computer altogether and has virtually no latency as a result The Direct Monitor knob controls how much of the direct monitor signal is sent straight to the main and headphone outputs Use this knob to set the monitoring level of the microphone instrument and auxiliary inputs that you are recording relative to the audio tracks that are playing from your computer gt IMPORTANT When using Direct Monitor you will need to disable software monitoring in your audio application Otherwise you will double monitor your input signals once through the Direct Monitor signal path and again through your computer software Disabling software monitoring varies from application to application but it is usually done by switching off record or input monitoring in your software or muting the channels that are record enabled See your software s documentation to learn more M AUDIO ProKeys Sono 61 User Guide 25 In a typical Direct Monitor scenario plug your microphone into the Microphone input and guitar into the Instrument input on the rear panel Configure a mono track to record from input channel one and a second mono track to record from input channel two Arm record enable both mono tracks in your audio software and set their recording levels using the gain controls on ProKeys Sono Next set the Direct Monitor Level and you are ready to record If you are recording your mic and guitar while listening to tracks already record
41. d of transposing ProKeys Sono is described in the ProKeys MIDI Output Settings chapter of this User Guide 3 Channel MIDI data from the keyboard can be sent on any of 16 MIDI channels The ProKeys Sono default is to transmit MIDI data on channel one However certain MIDI performance or recording scenarios may require the keyboard to send data ona different channel The Data lt and gt buttons can be configured to control the MIDI transmission channel setting This will allow the Data lt and gt buttons to decrement or increment through the channels When channel 16 is reached and gt is pressed channel one will be selected To assign the Data lt and gt buttons to alter the MIDI transmission channel 1 Press the Edit Mode button 2 Press the black key above C3 C 3 representing Data Channel ProKeys Sono will exit Edit mode as soon as C 3 has been pressed If the Data lt and gt buttons are assigned to adjust the MIDI channel the LEDs above the buttons will not change since it is not possible to have a channel with a negative value Pressing both the lt and gt buttons together will recall the default setting channel one An additional method of shifting the ProKeys Sono MIDI transmission channel is described in the ProKeys MIDI Output Settings chapter of this User Guide M AUDIO ProKeys Sono 61 User Guide 32 4 Program Change Program chan
42. d to install the M Audio driver software However M Audio recommends installing the device drivers for improved audio performance and to gain access to additional professional features such as Low latency software monitoring Low latency software monitoring allows you to play software synthesizers and monitor audio input through your recording software with minimal delay between an action e g pressing a key strumming a chord or singing a note and hearing the resulting sound on your speakers or headphones Multi client MIDI operation This feature allows you to use ProKeys Sono as a MIDI input and output device with more than one application at the same time Support of large System Exclusive SysEx transfers Transmit large SysEx files e g all parameters of every sound on an external synthesizer stored within a single file to connected Synthesizers or other MIDI devices m Pro Tools M Powered support Use ProKeys Sono as an audio interface with a qualified version of the Pro Tools M Powered production software If you do not require any of the above listed features you can simply connect ProKeys Sono to your Windows computer and begin using it without the need to install additional driver software Windows XP Vista users Important information for class compliant operation IMPORTANT When using ProKeys Sono class compliant i e without installing drivers in Windows the computer will search for the M Audio DFU device firmware
43. e Edit Mode button 2 Press the black key above F2 F 2 ProKeys Sono will automatically exit Edit mode 3 Press the Data gt and lt buttons to step forward and backwards through the built in GM sounds To return the Data keys to control the octave shift value 1 Press the Edit Mode button 2 Press the black key above C2 C 2 representing Data Octave ProKeys Sono will automatically exit Edit mode For additional information on program changes see the Advanced ProKeys Sono Functions in Edit Mode chapter of this User Guide M AUDIO ProKeys Sono 61 User Guide ProKeys Sono as a Standalone Microphone Preamplifier and Mixer Guitar ProKeys Sono back Anger tner RE Mono ARE i Powered Monitors ProKeys Sono can function as the centerpiece of a simple live performance setup Connect a Microphone and an Instrument such as an electric guitar or bass to ProKeys Sono and use the Microphone and Instrument gain knobs to set the input levels Next use the Direct Monitor knob to set the overall level of the microphone and instrument inputs in the mix Finally adjust the level of the keyboard s built in sounds by using the Voice Volume knob If you connected the line outputs of an external device to the aux inputs of ProKeys Sono the volume level of that device may need to be adjusted at the external device itself The mixed signal of Microphone Instrument Aux input and built in sounds will be avail
44. e the left Data button LED will illuminate Pressing both Data buttons together will center the keyboard and restore the default state Octave shift 0 and any illuminated Data button LEDs will turn off The Data buttons can also be assigned to send different MIDI messages or control other features on ProKeys Sono This is explained in the Advanced ProKeys Sono Functions in Edit Mode section of this User Guide Edit Mode Button Edit Mode When this button is pressed the associated LED illuminates and the keyboard enters Edit mode While in this mode the keys on the keyboard no longer transmit MIDI notes and are instead used to select advanced functions and enter data The Advanced ProKeys Sono Functions in Edit Mode section of this User Guide contains more detailed information about Edit mode Press this button again to exit Edit mode Master Volume Fader Master Volume The Master Volume fader controls the level of the main outputs 17 as well as the headphone outputs 2 M AUDIO ProKeys Sono 61 User Guide 15 16 Microphone Gain Knob Mic Gain This knob controls the gain level of the Microphone input The signal green LED illuminates when signal is present at the microphone input i e incoming audio signal is greater than 20dB The peak red LED illuminates when incoming audio signal is clipping distorting and indicates that the Microphone Gain knob should be turned down Instrument Gain Knob
45. e using within your recording software This configuration allows you to route MIDI data from your computer to the premium voices and GM sounds on ProKeys Sono Consult your software s documentation for instructions on how to configure the software for use with MIDI instruments that contain built in sounds such as ProKeys Sono NOTE Connect headphones or powered speakers to the ProKeys Sono main outputs Sounds created by ProKeys Sono and from software used with it will be available at the main outputs on ProKeys Sono not on the outputs of your computer s built in soundcard Sending MIDI to an external MIDI device connected to ProKeys Sono If you would like to send MIDI data to an external MIDI device connected to ProKeys Sono Select e ProKeys Sono 61 or USB audio device as the MIDI output hardware device within your recording software s MIDI setup options e ProKeys Sono MIDI Out or USB audio device 2 as the MIDI output port of the specific MIDI track you re using within your recording software 11 IMPORTANT If you are sending data to the ProKeys Sono MIDI Out port the ProKeys Sono Edit Mode function MIDI Out must be configured to allow your sequencer s MIDI data to be sent out of the MIDI output jack By default the MIDI output jack on the rear of the keyboard only receives data generated by playing the ProKeys Sono keyboard directly and does not receive MIDI data coming from your computer s sequ
46. ed in your computer you might want to listen once before starting the actual recording in order to set your Direct Monitor Level relative to the tracks playing from your computer gt IMPORTANT The Direct Monitor knob enables monitoring of all audio signals that enter any of the ProKeys Sono audio inputs However the ProKeys Sono outputs must be selected within your recording software in order to hear sounds created by virtual computer software based MIDI instruments Be sure ProKeys Sono 61 or USB Audio Device is selected as the audio output device within your recording software and that you have headphones connected to the headphone outputs on the front of ProKeys Sono or amplified speakers connected to the 1 4 outputs on the back of ProKeys Sono The Mono Button When the Mono button is pressed the Microphone input sends its signal to both the left and right outputs and the Instrument input also sends its signal to both the left and right outputs This means that you will hear these input signals centered between both speakers or your headphones When this button is not pressed the Microphone input will be sent to the Left Output and the Instrument input will be sent to the Right Output This means that the microphone input will be panned hard left i e heard only on the left speaker or headphone while your instrument input will be panned hard right when you listen back using Direct Monitor In its default state t
47. encing application via USB The operation of MIDI Out mode can be toggled by following the instructions found in the MIDI Out Mode Key portion of the Advanced ProKeys Sono Functions in Edit Mode chapter of this User Guide M AUDIO ProKeys Sono 61 User Guide Advanced ProKeys Sono Functions in Edit Mode The button to the left of the keys labeled Edit Mode is used to access additional functions of the keyboard When this button is pressed the keyboard enters Edit mode and the LED above the Edit Mode button illuminates If this button is pressed again the keyboard exits Edit mode the Edit mode button LED turns off and regular operation is resumed When in Edit mode the black keys on the keyboard are used for selecting functions while the white keys are used for data entry and channel selection Your keyboard will exit Edit mode as soon as either a function is selected or the CANCEL or ENTER key is pressed The LED above the Edit Mode button will turn off and the keyboard can then be used to play notes again Some functions do not require confirmation via the Enter or Cancel keys When these functions are selected the keyboard will automatically exit Edit mode and return to Performance mode gt IMPORTANT Not every music application can process all types of MIDI messages ProKeys Sono is capable of sending Please consult your software s documentation for information on what messages it can accept p1093y gsn 2AL
48. eset button is pressed ProKeys Sono performs the following sequence of functions o a a W N 10 12 13 14 MIDI Out mode is set to send MIDI from the keyboard to the computer via USB and to the external MIDI Out jack Local mode is set to Local On An All Notes Off command is sent on MIDI channel 1 A Reset All Controllers command is sent on MIDI channel 1 The Voice Volume knob is assigned to send MIDI controller 7 Volume messages The Modulation Wheel is assigned to send MIDI controller 1 Modulation messages The Sustain Pedal is assigned back to controller 64 Sustain The Global Transmit channel is set to 1 Transpose and octave shift are both set back to zero A Program Change 0 message is sent on MIDI channel 1 Bank Change MSB 0 and Bank Change LSB 0 messages are sent on MIDI channel 1 The Reverb Depth is set back to the default value for the Piano Voice The Chorus Depth is set back to the default value for the Piano Voice The current status of the Sustain Pedal is sent on MIDI channel 1 M AUDIO ProKeys Sono 61 User Guide Technical Specifications 44 1 kHz sampling rate unless otherwise stated Mic Inputs Input Impedance 4 4k Ohms Maximum Input Level at minimum gain 2 2 dBu 0 6 Vrms balanced SNR 96 dB A weighted Dynamic Range 96 dB A weighted THD N 0 004 88 dB 1 dBFS 1 kHz Frequency Response 20 Hz to 20 kHz 0 5 dB
49. ess the F4 key Default When the Default key is pressed the parameter is reset to its default value and Performance mode resumes M AUDIO ProKeys Sono 61 User Guide Pedal Assignment The Sustain pedal can be assigned to send standard MIDI CCs up to 127 and extended custom messages from 128 to 131 The default for the Sustain pedal is sending MIDI Controller message 64 Use the G 4 key in Edit mode to change the MIDI CC assignment for the Sustain Pedal To assign a MIDI controller message to the Sustain Pedal jack 1 2 Press the Edit Mode button Press the black key above G4 G 4 representing Pedal Assign Use the Numerical Data Entry keys G4 B5 to enter the number of the controller value you want to assign to the Sustain Pedal Jack Press C6 for ENTER If you make an error while entering the numerical data value you can press the CANCEL key C2 to exit Edit mode without changing the MIDI CC assigned to the Sustain Pedal jack To re assign the Sustain Pedal jack to its default function 1 2 3 Press the Edit Mode button Press the black key above G4 G 4 representing Pedal Assign Press the F4 key Default When the Default key is pressed the parameter is reset to its default value and Performance mode resumes Knob Assignment The Voice Volume knob can be assigned to any of 132 controllers 0 131 shown at the back of this manual in Appendix C To assign a MIDI controller message
50. essages must be followed by a program change message in order to recall a sound Bank change messages by themselves do not activate a sound but only locate and access a predefined location of a set bank of 128 sounds 7 Tuning This key will assign the Data buttons to increment or decrement the Master Tune Setting of ProKeys Sono The tuning range is 50 cents This only affects the internal sound engine Push and hold the Data lt or gt button while playing the keyboard until the desired tuning is found To assign the Data buttons to affect the tuning of the built in ProKeys Sono sounds 1 Press the Edit Mode button 2 Press the black key above D3 D 3 representing Data Tuning Now the Data lt and gt buttons can be used to adjust the master tuning of the sounds built into ProKeys Sono Pressing both the Data lt and gt buttons at the same time restores the tuning offset to zero M AUDIO ProKeys Sono 61 User Guide 33 Wheel Assignment It is possible to assign different MIDI controller numbers to the Modulation wheel These parameters are called MIDI continuous controllers MIDI CC There are 128 MIDI continuous controllers 0 127 counting from and including zero plus an additional 4 proprietary M Audio controller numbers for a total of 132 assignable parameters counting from and including zero to 131 Numbers beyond 127 are a proprietary method M Audio uses to simplify the transmission of
51. ge MIDI messages can be used to select any of the 128 built in MIDI instrument sounds on ProKeys Sono or to select sounds on external MIDI synthesizers or sound modules connected to the MIDI output jack NOTE When ProKeys Sono is set to Local On program change messages are always sent to the MIDI Out jack and the internal sound engine Program change messages can be sent to just the MIDI Out jack if the keyboard is set to Local Off For additional information on Local On and Local Off modes see the Local On Off Key section of this chapter If the Data lt and gt buttons have been assigned to control the program number the LEDs above the buttons will not change since it is not possible to select a program with a negative value To assign the Data lt and gt buttons to send program change messages 1 Press the Edit Mode button 2 Press the black key above F2 F 2 Pressing both the lt and gt buttons together will recall Program 0 which selects the first sound patch on any synthesizer capable of processing MIDI program changes Program 0 corresponds to the Grand Piano sound on ProKeys Sono An additional method of sending Program Change messages is described in the ProKeys MIDI Output Settings chapter of this User Guide 5 and 6 Bank LSB and Bank MSB Program changes are the most commonly used messages to change instruments and voices However the number of instruments accessible using
52. ges together constitute an RPN or NRPN command This allows for 16 384 values in total MIDI controllers 98 and 99 represent the NRPN LSB and MSB respectively while 100 and 101 represent the RPN LSB and MSB messages see the MIDI controllers list in Appendix C To transmit an NRPN RPN message these LSB and MSB controller messages are sent along with their user specified values A further controller message and value needs to be sent to specify the coarse or fine value adjustment This is specified by controller number 6 data entry for coarse adjustments or number 38 for fine adjustments A list of NRPN s is usually given in the user s manual of any device that receives NRPN messages It is always necessary that the NRPN MSB and LSB be sent together Both will be specified in the device s manual M AUDIO ProKeys Sono 61 User Guide 40 Troubleshooting ProKeys Sono is a high quality digital piano that has been tested under a wide variety of conditions to ensure trouble free performance In the event that you do experience difficulty with your ProKeys Sono this section provides tips to help resolve some basic issues that you may encounter Problem My ProKeys Sono keyboard suddenly stopped working after having performed fine since installation Solution Close any music applications you are using switch ProKeys Sono off and restart your computer Once your computer has completely restarted switch ProKeys Sono back on and try again
53. h Pad 88 New Age Synth Pad 89 Warm Synth Pad 90 Poly Synth Pad 91 Choir Synth Pad 92 Bowed Synth Pad 93 Metal Synth Pad 94 Halo Synth Pad 95 Sweep Synth Pad Synth Effects 96 SFX Rain 97 SFX Soundtrack 98 SFX Crystal 99 SFX Atmosphere 100 SFX Brightness 101 SFX Goblins 102 SFX Echoes 103 SFX Sci Fi Ethnic 104 Sitar 105 Banjo 106 Shamisen 107 Koto 108 Kalimba 109 Bag Pipe 110 Fiddle 111 Shanai Percussive 112 Tinkle Bell 113 Agogo 114 Steel Drums 115 Woodblock 116 Taiko Drum 117 Melodic Tom 118 Synth Drum 119 Reverse Cymbal Sound Effects 120 Guitar Fret Noise 121 Breath Noise 122 Seashore 123 Bird Tweet 124 Telephone Ring 125 Helicopter 126 Applause 127 Gun Shot M AUDIO ProKeys Sono 61 User Guide Appendix B Channel 10 Drum Map Drum Sound Drum Sound 35 Acoustic Bass Drum 59 Ride Cymbal 2 36 Bass Drum 1 60 Hi Bongo 37 Side Stick 61 Low Bongo 38 Acoustic Snare 62 Mute Hi Conga 39 Hand Clap 63 Open Hi Conga 40 Electric Snare 64 Low Conga 41 Low Floor Tom 65 High Timbale 42 Closed Hi Hat 66 Low Timbale 43 High Floor Tom 67 High Agogo 44 Pedal Hi Hat 68 Low Agogo 45 Low Tom 69 Cabasa 46 Open Hi Hat 70 Maracas 47 Low Mid Tom 71 Short Whistle 48 Hi Mid Tom 72 Long Whistle 49 Crash Cymbal 1 73 Short Guiro 50 High Tom 74 Long Guiro 5
54. he Mono button only affects how you hear signals from the Microphone and Instrument inputs but does not affect how these signals are recorded When recording to a stereo track signal from the Microphone input will appear as input channel one referred to as the left input in certain applications whereas the instrument input appears as input channel two the right input These signals can be recorded together on to a stereo track but it is recommended that you record the inputs on two separate mono tracks since this will give you more control over each individual track 4 Tip ProKeys Sono can be configured so that signals from the Microphone and Instrument inputs are recorded exactly as heard when monitoring in Mono Enable the MONO Input Record function in Edit mode to use this feature Once this setting has been made the Mono button will not only affect the way you hear yourself while recording monitoring but also how the signal is recorded by your computer In this scenario if the Mono button is active and you are recording to a stereo track in your sequencing software any mono source such as a Microphone or a connected instrument will be recorded to both channels of the stereo track left and right As a result both the microphone and instrument signals will appear centered between both speakers essentially creating a two channel mono recording See the Mono Input Record Key portion of
55. in MIDI interface However as you become more familiar with ProKeys Sono you may wish to take advantage of this device s additional professional features by installing the ProKeys Sono drivers Installing the ProKeys Sono drivers in Windows improves audio performance by reducing latency Latency is the time it takes for MIDI input when using software synthesizers or audio input signal to appear as audio at the ProKeys Sono audio outputs for monitoring Windows users will gain additional functionality from installing the ProKeys Sono drivers including using your new keyboard with more than one application at the same time multi client the ability to send large SysEx messages as well as using your ProKeys Sono with a qualified version of the Pro Tools M Powered recording software On a Macintosh installing the M Audio drivers enables you to use your ProKeys Sono with a qualified version of the Pro Tools M Powered recording software Information on Windows driver installation can be found in the printed Quick Start Guide included with your new ProKeys Sono Macintosh driver installation instructions are in the ProKeys Sono 61 Setup in OS X chapter of this User Guide Finally keep in mind that ProKeys Sono can be used with any third party music program Be sure to read your specific application s documentation to learn more about how it can best be used with this device 1 When using ProKeys Sono as a class compliant device in Windows i e
56. ions to be exchanged between two devices such as your ProKeys Sono and your computer rather than actual audio signals i e sounds In other words when a key is pressed on the ProKeys Sono keyboard a MIDI instruction is sent to your computer or hardware MIDI module to play a specific note at a specified velocity loudness No actual audio signals are transmitted over the MIDI connection The following image shows an example of a typical MIDI note message as transmitted over a MIDI connection and displayed within a MIDI sequencing application after recording The left side of the image shows a visual representation of a recorded MIDI note in the Piano Roll editor of a sequencing application For many MIDI users working with MIDI notes that are displayed this way is more intuitive than looking at the bare MIDI data in list form as explained next The right side of the image shows the same note in a sequencing application s MIDI event list editor very similar in format to how this information is transmitted over a MIDI connection 1 MIDI event type MIDI note 2 Start point of the MIDI note Note On 3 End point of the MIDI note Note Off 4 Pitch of the MIDI note 5 Velocity loudness of the MIDI note Regardless of how MIDI information is displayed in your sequencer visually in a piano roll editor as traditional score within musical staff or as a MIDI event list the recorded or transmitted MIDI information
57. is User Guide Reverb On Off Button Reverb On Off This button engages the internal reverb effect of ProKeys Sono adding the effect to the internal keyboard sounds of ProKeys Sono The reverb depth can be controlled via MIDI CC commands See the Advanced ProKeys Sono Functions in Edit Mode chapter of this User Guide for more information on this Chorus On Off Button Chorus On Off This button engages the internal chorus effect of ProKeys Sono adding the effect to the internal sounds of ProKeys Sono The chorus depth can be controlled via MIDI CC commands See the Advanced ProKeys Sono Functions in Edit Mode chapter of this User Guide for more information on this Voice Select Buttons These buttons let you select which of the five high quality sounds is played by the ProKeys Sono keyboard Keyboard ProKeys Sono features 61 full size semi weighted velocity sensitive keys M AUDIO ProKeys Sono 61 User Guide Rear Panel Descriptions 20 21 22 23 24 25 26 Auxiliary RCA Inputs Aux Input R L These line level RCA type inputs can lt 1 4 Instrument Input Instrument This unbalanced tip sleeve TS does not clip distort at the ProKeys connector allows you to connect an instrument such as an electric guitar or Sono input For example if you have bass Use the Instrument Gain knob 8 to control the gain level of this input connected a CD player to the RCA inputs d to adj
58. led Data Octave Data Transpose Data Program Data Bank LSB Data Bank MSB Data Channel and Data Tuning These keys are used to select the desired alternate function of the Data buttons To select alternate Data button functions 1 Press the Edit Mode button 2 Press the black key that represents the function you want to assign to the Data buttons ProKeys Sono will exit Edit mode as soon as you push one of these keys The LEDs above the Data buttons illuminate depending on their current setting The LED above the lt Data button will illuminate when the assigned parameter is set to a value less than zero the LED above the gt Data button will illuminate when the assigned parameter is set to a value greater than zero NOTE Data buttons can control certain functions that cannot be set to values less than zero such as MIDI channel selection When used to control these types of functions both lights above the buttons will remain off regardless of the current setting of that function M AUDIO ProKeys Sono 61 User Guide 31 Data Button Assignment Options 1 Octave Shift Default Data button assignment By default the Data lt and gt buttons control octave shift of the ProKeys Sono 61 keyboard Pressing the Data gt button right will shift the notes played on the keyboard up by one octave Pressing the Data lt button left will shift the notes played on the keyboard down by one oc
59. n Edit Mode chapter of this User Guide The order and naming of the MIDI ports may vary slightly depending on your operating system and sequencing application If ProKeys Sono is used as a class compliant device under Windows XP its output ports will appear as USB Audio Device and USB Audio Device 2 M AUDIO ProKeys Sono 61 User Guide Recording MIDI and triggering sounds on an external sound module Add A Track ProKeys Sono MIDI Out port Recording Software tU MIDI via USB TIP Follow the method described in the Recording the Aux Inputs to an Audio Track section Powered of this chapter to Monitors record the output of ProKeys Sono 61 p000 006 O MAUI ere cra J your external sound g s 1 O an O module as audio MIDI Out ME Heer within your recording toggled in Edit software mode Like the previous scenario ProKeys Sono is used to record to a MIDI track within the computer s sequencing software while simultaneously routing this MIDI information back to ProKeys Sono However instead of routing the MIDI signal back to the ProKeys Sono internal sound engine i e the ProKeys Sono Voices MIDI port the MIDI signal is routed to the ProKeys Sono MIDI Out jack i e to the ProKeys Sono MIDI Out port within your software This results in MIDI data being sent to an external MIDI sou
60. n the web at www m audio com
61. n to restore normal operation Note Your M Audio product has been tested to comply with FCC Standards FOR HOME OR OFFICE USE Modifications not authorized by the manufacturer may void users authority to operate this device Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures m Re orient or relocate the receiving antenna m Increase the separation between the equipment and receiver m Connect the equipment to an outlet on a circuit different from that to which the receiver is connected m Consult the dealer or an experienced radio TV technician for help ASIO is a trademark of Steinberg Soft und Hardware GmbH VST is a trademark of Steinberg Soft und Hardware GmbH Warranty Warranty Terms M Audio warrants products
62. nd module The MIDI sound module receives data from the ProKeys Sono MIDI output jack and generates audio sound that is routed back to the RCA inputs of the keyboard This output of the sound module can then be monitored through the headphone outputs of ProKeys Sono or via speakers connected to the 1 4 outputs as shown above 7 The order and naming of the MIDI output ports may vary slightly depending on your operating system and sequencing application If ProKeys Sono Is used as a class compliant device under Windows XP its output ports will appear as USB Audio Device and USB Audio Device 2 8 The ProKeys Sono MIDI Out Mode setting must be configured correctly for your sequencing application s MIDI output to appear at the MIDI output jack on the back of ProKeys Sono Please see the section entitled MIDI Out Mode Key in the ProKeys MIDI Output Settings chapter to find out more about this setting M AUDIO ProKeys Sono 61 User Guide 23 ProKeys Sono Audio Setup and Controls Using the Microphone and Instrument Inputs To record the microphone and instrument inputs of ProKeys Sono into your audio application 1 Select ProKeys Sono 61 or USB Audio Interface as an audio input device within your application s setup menu Please see your audio application s documentation to learn how to do this 2 Select ProKeys Sono 61 or USB Audio Interface as the audio track s output wi
63. ng you to harness the various features of ProKeys Sono ProKeys Sono transmits two types of data Audio and MIDI Audio is the same type of data that we encounter in our daily lives when we turn on the radio or television and hear the resulting sound Audio is the signal that is sent from microphones and instruments such as electric guitars and basses to speakers or amplifiers On the other hand the MIDI protocol consists of messages that are used to control synthesizers sound modules keyboards or virtual instruments found within computer software These MIDI data messages give instructions on how a sound should play These instructions dictate parameters such as what note to play when to play it how loud to play it and which sound to use The examples on the following pages will examine various recording scenarios by looking at a generic recording sequencing application and how it handles audio and MIDI data on separate track types Audio Tracks Audio tracks allow recording and playback of audio that originates from the Microphone Instrument or Aux inputs Audio tracks within your computer software can also be used to record the built in voices of ProKeys Sono as audio Once an audio recording is made you can apply effects or edit the recording by cutting or copying parts of the recording However the general sound of the recording is fixed if recorded using audio tracks and cannot easily be changed NOTE The following examples m
64. nt panel 1 4 headphone outputs Dedicated Instrument and Microphone gain control knobs with signal and peak LEDs Direct Monitor knob for near zero latency monitoring Stereo premium voices operate at a maximum polyphony of 20 notes M AUDIO ProKeys Sono 61 User Guide Minimum Requirements Standalone Operation Standalone operation refers to using ProKeys Sono without a computer To do this an optional 9V 500mA center positive power supply or USB type power supply is required More information on available power supplies can be found at www m audio com Bus Powered Operation In bus powered mode ProKeys Sono is connected to a PC or Mac with a USB cable and receives power through the USB connection When using ProKeys Sono in this mode your computer system must meet the following minimum specifications optional USB type external power supply Windows XP SP2 e Pentium III 1GHz or AMD K7 Athlon 1GHz CPU may be higher for laptops e 512 MB RAM One native USB port 3 Home and Professional Edition only Windows Media Center Edition is not currently supported M Audio ProKeys Sono 61 Windows Vista 32 bit e Pentium 4 1 6GHz or AMD Athlon XP 2800 CPU may be higher for laptops e 1 GB RAM e 128 MB Graphics Card One native USB port Mac OS X 4 Macintosh G4 1GHz e OS X 10 4 11 with 512 MB RAM OS X 10 5 2 with 512 MB RAM e One native USB port 1 G4 accelerator
65. o exit Edit mode TRANSPOSE To change the Transposition using the Transpose and Keys in Edit mode 1 Press the Edit Mode button 2 Press the black key above C5 C 5 representing Transpose to shift the keyboard down by one semitone 3 Press the black key above D5 D 5 representing Transpose to shift the keyboard up by one semitone 4 Press C6 representing ENTER or press the Edit Mode button to exit Edit mode M AUDIO ProKeys Sono 61 User Guide CHANNEL To change the MIDI transmission channel using the Channel Keys in Edit mode 1 Press the Edit Mode button 2 Press one of the 16 Channel keys from D2 to E4 whichever one represents the channel you need ProKeys Sono will exit Edit mode as soon as a Channel key has been pressed NOTE In accordance with the General MIDI specification channel 10 is reserved for drum sounds To send data on channel 10 1 Press the Edit Mode button 2 Press the F3 key on ProKeys Sono to select channel 10 MIDI Out Mode Key The MIDI Out Mode key G 3 determines what data is sent to the external MIDI Out jack Pressing this key in Edit mode will toggle between two options 1 MIDI generated by playing the keys on the keyboard is sent to the external MIDI output jack default 2 MIDI signals from the computer s sequencing application that are routed to the ProKeys Sono MIDI Out port are sent to the external MIDI output jack When the M
66. o ProKeys Sono from the recording application To prevent notes from being Powered Monitors triggered twice configure ProKeys ProKey Sono S Sono to operate in Local Off mode HI 0000 0900 60066 Sono 61 Internal General MIDI op In this scenario ProKeys Sono is used to record to a MIDI track within the computer s sequencing software The MIDI data is See page 37 for more information on how to do this 0 recorded simultaneously passed through the software and routed back to the ProKeys Sono Voices MIDI output port this port connects to the sound engine of ProKeys Sono Audio is then generated by the built in sound engine of ProKeys Sono and sent to powered monitors through the main outputs gt IMPORTANT Built in ProKeys Sono sounds can also be recorded as audio to an audio track within your recording software By default sounds generated by the built in sound engine of ProKeys Sono are merged into audio input channels one and two mixing them with input signals from the Microphone Instrument and Aux inputs The mixed signal can be recorded by your recording software If you do not wish to send the audio signal created by playing the built in ProKeys Sono sounds to your software audio inputs this can be accomplished by toggling the USB Record switch in Edit mode Additional information on this can be found in the USB Record Key portion of the Advanced ProKeys Sono Functions i
67. oKeys Sono select a particular sound bank internal sound engine and also to any external To send a single bank change in Edit mode devices connected to the ProKeys Sono MIDI Out jack Now the keyboard is set to play the internal General MIDI cello sound 42 from the General MIDI Instruments standard list The full list of General MIDI program numbers is given 3 Press the number keys G4 through B5 that in Appendix A at the end of this manual correspond to the bank number you wish to select 1 Press the Edit Mode button 2 Press the black key above G5 G 5 or A5 A 5 representing Bank LSB or Bank MSB respectively 4 Press C6 Enter ProKeys Sono will exit Edit mode as soon as a C6 has been pressed NOTE Bank change messages must be followed by a program change message in order to load a sound Bank change messages by themselves do not activate a sound but only locate and access a predefined location of a set bank of 128 sounds M AUDIO ProKeys Sono 61 User Guide MIDI Messages In Depth Program amp Bank Changes When the MIDI standard was first established it enabled the user to access only 128 different sounds using program change messages 0 127 As MIDI devices grew to be more sophisticated and contain more sounds bank change messages were included in an updated MIDI specification to allow for more than 128 sounds to be accessed The language MIDI uses to communicate between musical instruments only
68. om the keyboard yet still receive MIDI data from a connected computer When the Local On Off key is toggled the sounds built into ProKeys Sono will not be played by the piano keyboard However notes played on the keyboard will continue to be sent to the MIDI Out jack as well as to the computer via USB In standalone mode the Local On Off key allows a remote MIDI device to be controlled without ProKeys Sono playing its internal sounds In Edit mode when the Local On Off Key is pressed the function is toggled and Edit mode is exited The keyboard then returns to Performance mode and the Edit Mode LED goes out At any time pressing the Piano Reset button will restore this mode to Local On Switching the keyboard off and on will also restore this setting back to its default Local Off mode is often used to control a software synthesizer running on a connected computer without layering the built in ProKeys Sono sounds on top of the software synthesizer s tone M AUDIO ProKeys Sono 61 User Guide 37 Panic ProKeys Sono has been designed to make working with MIDI on your computer as simple as possible However sometimes things can go wrong and you may experience stuck notes i e notes that sustain indefinitely or unexpected changes in your sounds due to errant MIDI CC commands being issued ProKeys Sono includes a Panic function to counter this This function sends Reset All Controllers and All Notes OFF messages on
69. ow the Mono button is configured to function the microphone input routing can be altered to make the microphone appear on both channels one and two of a stereo track i e centered in the stereo field This functionality may be helpful in direct monitoring situations where headphones are being used To learn more about this see the section titled The Mono Button within the ProKeys Sono Audio Setup and Controls section of this User Guide TIP Signal from the ProKeys Sono microphone input is usually available on input channel one within your recording software To record from a microphone this mono audio track must be configured to receive signal from audio input channel one See your audio application s documentation to learn how to configure an audio track TIP When recording with a microphone in your studio it is recommended that you turn off your speakers and monitor through headphones This prevents feedback loops which may be very loud and can damage your equipment or harm your hearing M AUDIO ProKeys Sono 61 User Guide Recording an Instrument to an Audio Track 00000 EEE ot o 1nQ olpny gt Q oe Powered Instrument Monitors ProKeys Sono 61 Like the previous scenario ProKeys Sono is being used as an audio interface However this time the instrument input is being used to record an electric guitar or bass into your computer The gui
70. put These RCA inputs are designed to accept signals from any sound source with line level outputs such as a synthesizer drum machine or CD player TIP You can also use audio applications to play your MIDI files into your external synthesizer and Using music software you can record audio into your computer from any sources record the output of the synthesizer with line level outputs such as CD players drum machines etc back into your computer This allows you to apply software plug in gt IMPORTANT By default the Aux inputs and the built in ProKeys Sono effects to these tracks To do this sounds blend with the Instrument and Microphone inputs before their signals MIDI sequences must be routed to are sent to a connected computer via USB If the Aux inputs or any of the an external sound module while the built in voices are used simultaneously with the Instrument and Microphone audio application records the analog inputs the resulting recording will be a mix of the various signals It is not outputs of the external MIDI module possible to separate these blended signals after a recording has been made through the ProKeys Sono Aux If you want to edit or mix the Piano Microphone Instrument or Aux inputs inputs Additional information on this after the recording has been made then you will need to make a recording can be found in the Recording the of each of these sound sources one at a time and on separate tracks Aux Inputs
71. rdware controllers will be lost and the defaults will be restored ProKeys MIDI Output Settings Vel Curve Selection ProKeys Sono provides three velocity curves to accommodate a variety of playing styles Three of the keys in Edit mode are dedicated to the selection of the built in Low Mid and Hi velocity curves The default curve is Mid which will always be selected when ProKeys Sono is powered on Pressing one of these keys in Edit mode selects an alternative curve Vel Curve LOW F 1 makes it easier to play quietly This curve generates lower velocities than the default curve MID Vel Curve MID G 1 is a neutral curve between the low and hi velocity curves Vel Curve HI A 1 makes it easier to play loudly This curve generates higher velocities than the default curve MID After one of the Velocity Curve keys is pressed in Edit mode Performance mode resumes OCTAVE To change the Octave shift using the Octave and Keys in Edit mode 1 Press the Edit Mode button 2 Press the black key above C4 C 4 representing Octave to shift the keyboard down by one octave It is possible to shift the keyboard down a total of three octaves 3 Press the black key above D4 D 4 representing Octave to shift the keyboard up by one octave It is possible to shift the keyboard up a total of four octaves 4 When you have chosen your octave shift either press C6 representing ENTER or press the Edit Mode button t
72. roKeys Sono 61 User Guide Recording the Aux Inputs to an Audio Track 00000 EXA o Add A Track Ibias lon Sound Module or CD Player Powered Monitors ProKeys Sono 61 0000 00606 6060666 00 Once again ProKeys Sono is being used as an audio interface However in this scenario the auxiliary input jacks are being used to record the output of an external device such as a sound module CD player or other line level device The external device s stereo output is received at the RCA input jacks on ProKeys Sono and sent to the computer through the USB connection Sequencer software running on the computer can then capture the device s signal on a stereo audio track labeled Aux Stereo in the illustration above Signal entering the left Aux input is routed to the left channel of your software i e channel one while the right Aux input is routed to the right channel channel two of the recording software This stereo signal can be monitored while recording or played back after it has been recorded Monitoring can take place over powered speakers connected to the 1 4 main output jacks on the rear panel or by headphones connected to either one of the 1 4 headphone jacks on the front panel TIP Signal from the ProKeys Sono auxiliary inputs are usually available on input channels one and two within your recording software To record the ex
73. such so you know that their sounds are organized in the General MIDI structure When a GM device receives a MIDI program change it calls up a type of sound that you expect from the GM sound set All non GM MIDI sound modules call up unique sounds from their memory upon receiving MIDI program changes Since the sounds in a non GM device are not arranged in a particular order you need to take a look at the device itself to see which sound you want and at which location in the memory it resides Many VST instruments such as Native Instruments FM7 or the synth modules in Propellerhead Reason are non GM devices You can send Program Change Bank LSB and Bank MSB messages directly from the ProKeys Sono keyboard Please consult the Advanced ProKeys Sono Functions in Edit Mode section of this User Guide for further details NRPN RPNs Non registered parameter numbers NRPN s are device specific messages that enable you to control synthesizers and sound modules via MIDI The MIDI specification defines open parameter numbers to allow manufacturers to specify their own controllers The more common of these are registered by the MIDI Manufacturer s Association and are now part of the MIDI specification hence the term Registered Parameter Numbers RPN s See Appendix C Each NRPN RPN has an associated 2 byte number The two bytes allow for 128 values each An RPN or NRPN message is made up of two parts the MSB and the LSB message Both of these messa
74. t ProKeys Sono can connect to external MIDI devices such as synthesizers or sound modules through this jack By default MIDI data generated by playing the keys on the keyboard is sent to this MIDI output jack However it is possible to configure ProKeys Sono to act as a USB to MIDI interface allowing MIDI data from your computer to be sent out of this jack See the MIDI Out Mode Key section of the Advanced ProKeys Sono Functions in Edit Mode chapter for more information USB Port e Use the provided USB cable to connect ProKeys Sono to an available USB port on a PC or Macintosh computer This USB connection will power ProKeys Sono and allow transfer of audio and MIDI data between your computer and the device Alternatively an optional USB type power supply can be connected to this port for standalone operation Powering ProKeys Sono DC Power Supply Port 9V DC Connect an optional 9V DC gt 500mA ProKeys Sono can be powered center positive power supply to this jack when using ProKeys Sono in standalone Meme LER AO mode This port does not need to be used when ProKeys Sono is connected to DC Power Supply port It is NOT your computer with a USB cable or if a USB type power supply is being used necessary to power the device through both ports For example if On Off Switch I O This On Off switch turns ProKeys Sono on and off Fener Kensington Security Slot fi This slot is compatible with Kensington computer using
75. tar s output signal is received at the 1 4 instrument input jack on ProKeys Sono and sent to the computer through the USB connection Sequencer software running on the computer can then capture the guitar s signal on one of its mono audio tracks the track is labeled Instr in the illustration above This signal can be monitored while recording or played back after it has been recorded Monitoring can take place over powered speakers connected to the 1 4 main output jacks on the rear panel or by headphones connected to either one of the 1 4 headphone jacks on the front panel Keep in mind that depending on how the Mono button is configured to function the instrument input routing can be altered to make the instrument appear on both channels one and two of a stereo track i e centered in the stereo field This functionality may be helpful in direct monitoring situations where headphones are being used To learn more about this see the section titled The Mono Button within the ProKeys Sono Audio Setup and Controls section of this User Guide TIP Signal from the ProKeys Sono instrument input is usually available on input channel two within your recording software To record the instrument s output this mono audio track must be configured to receive signal from audio input channel two See your audio application s documentation to learn how to configure an audio track M AUDIO P
76. tave Pressing both Data buttons together will restore the default octave Octave shift 0 If you have changed the Data button assignment and would like to re assign the Data buttons to control octave shift again 1 Press the Edit Mode button 2 Press the black key above C2 C 2 representing Data Octave ProKeys Sono will exit Edit mode as soon as C 2 has been pressed The LEDs above the buttons indicate the direction of the octave shift An additional method of shifting the ProKeys Sono octave is described in the ProKeys MIDI Output Settings chapter of this User Guide 2 Transpose In many cases it is useful to increase or decrease the transmitted pitch by a small number of semitones For example you may be playing a song with a singer and the singer is having trouble hitting the high notes In this case you can try reducing the pitch by one or more semitones This is achieved using a function called Transpose To assign the Data lt and gt buttons to transpose 1 Press the Edit Mode button 2 Press the black key above D2 D 2 representing Data Transpose ProKeys Sono will exit Edit mode as soon as D 2 has been pressed When the Data buttons are assigned to transpose the keyboard the LEDs above the buttons indicate the direction of the transposition To return the keyboard s transpose shift to zero press both the Data lt and gt buttons at the same time An additional metho
77. ter will recognize ProKeys Sono without the need to install the M Audio driver software However M Audio drivers need to be installed if you are planning to use ProKeys Sono with a qualified version of the Pro Tools M Powered music production software gt IMPORTANT Disconnect ProKeys Sono from your computer until the appropriate driver files have been copied to your hard drive The instructions will indicate when the keyboard should be connected to your computer 1 We recommend that you download the most recent drivers by going to the Support gt Drivers page at www m audio com This ensures that you have the newest drivers available If you do not have Internet access insert the M Audio ProKeys Sono Drivers and Documentation CD ROM into your computer to install the drivers that came with the keyboard a If you are installing drivers from the M Audio ProKeys Sono Drivers and Documentation CD ROM a CD ROM icon will appear on your desktop once the disc is inserted into your computer Double click this icon to view the contents of the disc Next double click Open Me Finally select your product from the drop down menu on the welcome screen and click Install b If you are installing drivers from www m audio com the downloaded file should automatically mount and display its contents If this file does not automatically mount after it has finished downloading click on the file from the download stack Mac OS X 10 5 or double click the
78. ternal device s outputs a stereo audio track must be configured to receive signal from audio input channels one and two See your audio application s documentation to learn how to configure an audio track Keep in mind that depending on how the Mono button is configured to function the routing of the auxiliary inputs can be altered to make the left and right channels appear as a mono sound source that is centered in the stereo field This functionality may be helpful in direct monitoring situations where headphones are being used To learn more about this see the section titled The Mono Button within the ProKeys Sono Audio Setup and Controls section of this User Guide M AUDIO ProKeys Sono 61 User Guide MIDI Tracks 20 MIDI tracks allow you to record the notes you play on the ProKeys Sono keyboard as MIDI data The benefit of using MIDI tracks is that nearly every aspect of each recorded note can easily be changed For example you can change the pitch duration or even the instrument sound after a recording has been made However you always need to have a MIDI instrument available in order to play back MIDI tracks ProKeys Sono has a built in sound engine that gives you 128 standardized General MIDI sounds including the five ProKeys Sono premium sounds Additionally you can choose to use virtual instrument software within your recording application or connect an optional MIDI sound module to the MID
79. thin your recording software Again see your audio application s documentation to learn how to do this ProKeys Sono features high gain low noise preamplifiers on its microphone channel one and instrument channel two inputs Channel one features a low impedance input with an XLR connector and is designed to receive the output of a dynamic microphone Channel two has a 1 4 high impedance instrument input and is designed to accept signals from an electric guitar bass or other high impedance source You may attach a direct box or passive transformer to the microphone input channel 1 if you would like to plug another guitar bass or other high impedance instrument into the ProKeys Sono Microphone input Setting Input Gain The M Audio ProKeys Sono Mic input channel one and Instrument input channel two each provide up to 35dB of gain Microphones electric guitars and basses typically emit low instrument level signals and require preamplifiers such as the ones in ProKeys Sono to boost the signals before being recorded Plug in your microphone or instrument with the gain controls turned down While playing your instrument or singing into the microphone at the loudest section of the song slowly turn the gain knob clockwise until the red clip LED begins to illuminate Then turn the knob counter clockwise until the clip indicator no longer illuminates At this point you should be ready to record with the optimum gain setting
80. to an Audio Track portion of the Using ProKeys Sono with a Computer chapter of this User Tip ProKeys Sono can be configured so that its built in instrument sounds Guide After recording you can mix are NOT sent to the computer via USB and therefore will not be recorded ihose tracks with other audio tracks along with signals from the audio input jacks See the USB Record Key such as vocals and guitar entirely portion of the Advanced ProKeys Sono Functions in Edit Mode chapter of from within your computer this User Guide for additional information on this Using Direct Monitoring When a microphone or instrument is plugged into the inputs of ProKeys Sono its signal needs to be converted to a digital signal which then gets sent to the computer via the USB cable From there the signal is sent to your music software processed and returned to the ProKeys Sono main outputs This process usually takes a few fractions of a second to make the round trip and that delay is known as latency Latency is not a problem when playing back music but it can be distracting while recording your performances To compensate for this delay M Audio ProKeys Sono has a feature called Direct Monitor Direct Monitor duplicates your incoming signal and sends one copy of the signal straight to the outputs the other copy of the signal is sent to the computer The signal that is sent directly to the outputs bypasses the
81. to be free from defects in materials and workmanship under normal use and provided that the product is owned by the original registered user Visit www m audio com warranty for terms and limitations applying to your specific product Warranty Registration Immediately registering your new M Audio product entitles you to full warranty coverage and helps M Audio develop and manufacture the finest quality products available Register online at www m audio com register to receive FREE product updates and for the chance to win M Audio giveaways WARNING This product contains chemicals including lead known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling M AUDIO ProKeys Sono 61 VEI C Tested to comply with FCC standards FOR HOME OR STUDIO USE Avid ES 2009 Avid Technology Inc All rights reserved Product features specifications system requirements and availability are subject to change without notice Avid M Audio and ProKeys Sono 61 are either trademarks or registered trademarks of Avid Technology Inc All other trademarks contained herein are the property of their respective owners 9329 65017 00 M AUDIO Apart of Avid www m audio com M AUDIO 5795 Martin Road Irwindale CA 91706 USA TECHNICAL SUPPORT Visit the M Audio Online Support Center at www m audio com support PRODUCT INFORMATION For company and product information visit us o
82. to see if the problem resolves Problem have connected a sustain pedal to my M Audio keyboard but its operation is reversed i e the notes sustain when the pedal isn t pressed but the notes stop sustaining once the pedal is pressed Solution The polarity of the sustain pedal is calculated by the keyboard upon startup When ProKeys Sono is powering up the sustain pedal is assumed to be in the OFF position It is important that the sustain pedal is not pressed down during startup otherwise its operation may be reversed If you would like to intentionally reverse the polarity of your sustain pedal i e notes are sustained when the pedal is up notes stop sustaining when the pedal is pressed hold the pedal down while the keyboard is being switched on Problem When playing a virtual instrument loaded in my music software or when attempting to monitor my microphone or instrument input there is a noticeable delay before hear any sound Solution This delay is known as latency and it can be adjusted by changing the buffer size setting in your M Audio Control Panel The goal is to set the buffer size as low as possible without experiencing artifacts in the audio Faster computers generally allow for smaller buffer size settings and thus less latency When monitoring signals from the Microphone Instrument or Aux inputs you can also avoid this problem by using the Direct Monitor knob instead of monitoring through your music software See
83. to the Voice Volume knob 1 2 3 4 Press the Edit Mode button Press the black key above A4 A 4 representing Knob Assign Use the Numerical Data Entry keys G4 B5 to enter the number of the controller value you want to assign to the Voice Volume knob Press C6 for ENTER If you make an error while entering the numerical data value you can press the CANCEL key C2 to exit Edit mode without changing the MIDI CC assigned to the Voice Volume knob To re assign the Voice Volume knob to its default function i 2 3 Press the Edit Mode button Press the black key above A4 A 4 representing Knob Assign Press the F4 key Default When the Default key is pressed the parameter is reset to its default value and Performance mode resumes TIP Using the Modulation wheel or Voice Volume knob to set the reverb or chorus depth on ProKeys Sono Changing Reverb Depth The Modulation wheel and or the Voice Volume knob can be re assigned to control the depth of the built in ProKeys Sono reverb To do this 1 Press the Edit Mode button 2 Press either the Wheel Assign F 4 or Knob Assign A 4 key 3 Press B5 to enter 9 4 Press A4 to enter 1 so you have entered 91 5 Press C6 for ENTER This setting can be undone by powering the unit off and back on or by using the Default key as described in the next section CC 91 is the standard MIDI con
84. troller number for reverb depth see Appendix C Changing Chorus Depth The Modulation wheel and or the Voice Volume knob can be re assigned to control the depth of the built in ProKeys Sono chorus To do this 1 Press the Edit Mode button 2 Press either the Wheel Assign F 4 or Knob Assign A 4 key 3 Press B5 to enter 9 4 Press C5 to enter 3 so you have entered 93 5 Press C6 for ENTER This setting can be undone by powering the unit off and back on or by using the Default key as described in the next section CC 93 is the standard MIDI controller number for chorus depth see Appendix C NOTE Optional MIDI parameters assigned to the Voice Volume knob Modulation wheel or Sustain Pedal jack are not stored when the keyboard is turned off These parameters will reset to their default values each time the keyboard is powered on M AUDIO ProKeys Sono 61 User Guide 35 Restoring Default Assignments The Default key is used to selectively reset controller assignments To reset a specific controller assignment be sure you are in Edit mode Press the key for the parameter you would like to reset Knob Assign Pedal Assign or Wheel Assign and then press the Default key F4 When the Default key is pressed the parameter is reset to its default value and Performance mode resumes NOTE Each time the keyboard is turned off optional MIDI parameters assigned to specific ha
85. upgrade tool and display a Found New Hardware Wizard The M Audio DFU is a component of ProKeys Sono 61 that is enabled when the M Audio drivers are installed but is not necessary for class compliant operation You have the following options A Cancel the Found New Hardware Wizard and start using ProKeys Sono immediately The Found New Hardware Wizard will appear every time your computer detects that the device is connected e g upon restarting the computer or disconnecting reconnecting ProKeys Sono B Follow the Found New Hardware Wizard until it gives the option not to be prompted to install this hardware again Windows Vista Users Select Don t show this message again for this device in the first screen that appears Click Continue in the confirmation screen that follows Windows XP Users In the first screen select No not this time and click Next In the second screen select Install the software automatically and click Next Finally make sure the check box labeled Don t prompt me again to install this software is active then click Finish C Install the M Audio drivers as described in the Driver Installation for ProKeys Sono 61 section of the Quick Start Guide After these drivers have been installed the Found New Hardware Wizard for the M Audio DFU will no longer be displayed M AUDIO ProKeys Sono 61 User Guide ProKeys Sono Setup in Mac OS X Your compu
86. ust th XLR Microphone Input Microphone This input accepts a dynamic Lr Ome Maret ramet PES P 0 17 18 19 20 21 22 23 24 25 26 1 4 Main Outputs Output R L Mono Connect these unbalanced tip sleeve TS main outputs to your mixer powered speakers or amplifier These jacks output a mixed signal consisting of the ProKeys Sono internal piano sounds signal from all of the keyboard s inputs mic instrument and auxiliary and audio signal coming from your computer If you are connecting to a mono single channel device or amplifier use the left 1 4 output TIP The ProKeys Sono Auxiliary inputs do not have an input gain receive signal from a variety of sources such as mixers CD players or drum khob NE MT machines These inputs are mixed into the outputs of ProKeys Sono and will be inputs must be adjusted at the source heard on the 1 4 main outputs 17 or headphone outputs 2 to ensure that the incoming signal output volume of the player itself to microphone connected via a standard three pin balanced XLR cable Use the P pray ensure distortion free recordings Microphone Gain knob 7 to control the gain level of this input Sustain Pedal Jack Sustain Connect an optional sustain pedal to this jack This pedal is normally used for sustaining the sound you are playing without having to keep your hands on the keyboard just like the sustain pedal on a piano MIDI Out Jack MIDI Ou
87. ut port This option of looping MIDI data back to its source is sometimes referred to as MIDI Monitor or pass through and allows synthesizers to trigger their own sounds when Local Off mode is engaged See your software s documentation for more information on this Problem My ProKeys Sono MIDI controls such as Voice Volume knob data buttons the Reverb and Chorus on off buttons etc stopped working when the keyboard was set to Local Off mode Solution lf your ProKeys Sono has been set to Local Off mode the MIDI Controls piano keys knobs buttons etc are disconnected from the internal sound engine and will not directly control the sound engine In this case you must make sure that the MIDI track in your sequencing software is configured to route the MIDI signals from ProKeys Sono back to the keyboard by activating ProKeys Sono Voices as the MIDI output port for the selected MIDI track Once MIDI data is routed back to ProKeys Sono this way the various MIDI controls will continue to work as expected M AUDIO Appendices Useful MIDI Data ProKeys Sono 61 User Guide Appendix A General MIDI Instruments Piano 0 Acoustic Grand Piano 1 Bright Acoustic Piano 2 Electric Grand Piano 3 Honky Tonk Piano 4 Electric Piano 1 5 Electric Piano 2 6 Harpsichord 7 Clavinet Chromatic Percussion 8 Celesta 9 Glockenspiel 10 Music Box 11 Vibraphone 12 Marimba 13 Xylophone 14 Tubular bells

M-Audio 61 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents