Linear 1099 User's Manual
Contents
1. TRANS PRIMARY Figure 2 1099 20 IF YOU HAVE THE MODEL 1099 30 Wire the red and black wires to a 24VAC power supply Connect the remaining gray wires as specified by the manufacturer of your operator If such instructions do not exist wire the two gray wires in parallel with the pushbutton terminals If the operator has a three wire terminal the proper terminals will usually be marked 1 and 2 or 24V and RELAY see figure 3 CONTROL BOX RECEIVER Figure 3 1099 30 IF YOU HAVE THE MODEL 1099 40 The red wire will go to the positive 12 volt terminal in the operator The black wire will go to the negative terminal or ground terminal of the operator Connect the two gray wires as specified by the manufacturer of your operator If such instructions do not exist wire the two gray wires in parallel with the pushbutton terminals see figure 4 CONTROL z BOX RECEIVER Figure 4 1099 40 At this point you should mount your 1099 receiver to its permanent installation if you have not already done so ANTENNA INSTALLATION After you have mounted your receiver test it with the enclosed antenna for range noting the coverage that you get from all desired operating locations If greater range or coverage pattern is necessary you may need the 1066 Coaxial Wiring Kit which is available from your dealer Note that the 1099 external antenna coupling used a TYPE B2. NC antenna fitting If necessary you may use a TYPE BNC to TYPE F adapter allowing you to use fittings found where television antennas are sold along with 75 ohm antenna wire It is not advisable to use lengths greater than 20 feet as this may affect range or tuning ADDITIONAL INSTALLATION INFORMATION Linear Corporation has taken every possible precaution to make the 1099 receiver as reliable as possible We think the following notes should be observed 1 Be sure the unit is sealed from moisture and if at all possible keep it away from direct moisture 2 In those installations where vibration may be a factor be sure to use a fastening compound such as LOCTITE TM on the mounting screws to insure reliable mounting 3 If this or any other equipment is being used in a safety related device be sure to test the entire system at the time of installation and at frequent intervals to determine that it is working properly OPERATIONAL CHECK To check operation move back a reasonable distance about 50 feet and press the transmitter button Operation should be reliable at this distance but environment and location of both the transmitter and receiver will affect the range If the transmitter is stowed well out of sight it may be necessary to remove it from its mounting and hold near the windshield Try different locations and positions If operation is still unsatisfactory check the following 1 The antenna must be con
3. before completing the installation CODE SWITCH Figure 1 INSTALLATION The receiver comes equipped with a BNC receptacle and an antenna with a BNC plug The antenna can be plugged directly into the receptacle or it can be moved away from a metal structure or to an outside location for better receiver performance by using a coaxial kit available from your dealer Begin your installation of the 1099 by correctly wiring the receiver to the devices you will be using WE URGE YOU TO BECOME FAMILIAR WITH THE INSTRUC TIONS THAT THE MANUFACTURER OF YOUR EQUIPMENT HAS PROVIDED SINCE IN MANY CASES THESE INSTRUCTIONS WILL DETER MINE THE WAY IN WHICH THE 1099 RECEIVER WILL BE INSTALLED The receiver should be mounted near the opener power head and can be installed in any position by using screws and the two slots in the cover flanges Select a location and position that permits access to the terminals and space for the antenna as clear of metal structures as possible and preferably in a vertical position IF YOU HAVE THE MODEL 1099 20 Plug the trans former into a convenient 115 volt outlet Connect the remaining gray wires as specified by the manufacturer of your operator If such instructions do not exist wire the two gray wires in parallel with the pushbutton terminals If the operator has a three wire terminal the proper terminals will usually be marked 1 and 2 or 24V and RELAY see figure 2 F i
4. gainst the performance of our product nor is it liable for any costs related to loss of life property or revenue Further Linear Corporation is in no way responsible for installation of our product and will assume no costs to re installation or removal Linear Corporation s Warranty is in lieu of all other warranties expressed or implied CAUTION Any changes or modification in intentional or unintentional radiators which are not expressly approved by LINEAR CORPORATION could void the user s author ity to operate this equipment This applies to intentional and unintentional radiators certified per Part 15 of the F C C rules and regulations LINEAR CORPORATION 2055 Corte del Nogal Carlsbad CA 92009 760 438 7000
5. nected to the receiver for normal use 2 If the opener fails to operate check to see that 115 VAC power is present Check circuit breakers or for a system power failure 3 If the opener operates by pressing the wall button but not when the transmitter button is pressed the radio controls are probably at fault Check to make sure both transmitter and receiver code switches are set to the exact same code since a difference of just one switch will prevent operation Check transmitter bat tery location of the transmitter and receiver installation 4 Try mounting the antenna at a more favorable remote location by utilizing the coaxial kit If after performing the above operational check it is necessary to return the radio controls return both the transmitter and receiver to your dealer for repair or replacement or they may be returned postage prepaid directly to Linear Corporation WARRANTY ALL MULTI CODE garage door related products carry an eighteen 18 month warranty against defects in workmanship or material This warranty begins at the date of manufacture for eighteen months Linear Corporation warrantees our product only to our authorized dealers and distributors and not to the end customer If you have any questions about our warranty please ask your dealer to determine the nature and scope of his warranty Linear Corporation does not assume and is not responsible for any real or consequential damages from claims a
6. vl MULTI CODE Installation Instructions GARAGE DOOR RADIO CONTROLS MODEL 1099 RECEIVERS A WARNING e Disconnect power before any installation or repair e Wear safety glasses Your Multi Code Radio Controls are designed specifically for the remote control of industrial door or gate openers and to give years of dependable service without adjustment Before you continue to read these instructions note that there are 3 versions of the model 1099 receiver The model 1099 20 uses a 115 24 volt transformer The model 1099 40 comes with 4 wire connections for use with 12VDC systems The model 1099 30 comes with 4 wire connections for use with 24VAC systems In addition if you should choose to cut the transformer away from the 1099 20 this modified product MUST ALSO BE WIRED TO 24VAC ONLY SELECTING A CODE The code is determined by the positions of the 10 small switches numbered 1 through 10 located on the receiver board To gain access to the switch remove the top section of the case Any combination of ON CLOSED or OFF OPEN positions can be selected by using a small screwdriver or ball point pen see figure 1 We strongly urge that you avoid the following code schemes ALL ON ALL OFF 2 4 6 8 10 on or 1 3 5 7 9 on These codes are frequently used by other manufacturers and create the possibility of false operation and may be less secure than other code schemes Be certain to check that the code is functional
Download Pdf Manuals
Related Search