Lincoln Electric CAN-F27 User's Manual
Contents
1. LI N C O L N G Date 1 5 2009 MSDS No CAN F27 Trade Name MIL 800 HPNi Supersedes 9 10 2007 MATERIAL SAFETY DATA SHEET For Welding Consumables and Related Products Conforms to Workplace Hazardous Materials Information System WHMIS Rev November 1988 Section I amp II Preparation and Product Information Product Type Submerged Arc Flux Representative Classifications AWS F8A6 ENi1K G H2 The Lincoln Electric Company of Canada LP A 179 Wicksteed Avenue F9A4 ENi5 G H2 Toronto Ontario M4G 2B9 CANADA Prepared by The Lincoln Electric Company Cleveland Ohio USA Phone 416 421 2600 216 481 8100 on the date shown above Section III Hazardous Ingredients 1 IMPORTANT This section covers the materials from which this product is manufactured The fumes and gases produced during welding with the normal use of this pr duct are covered by Section VII see it for industrial hygiene information AS Number shown is representative for the ingredients listed 1 The term hazardous in Hazardous Ingredients should be interpreted as a term required and defined in the Hazardous Products Act and does not necessarily imply the existence of any hazard TLV LDso LCs mg m Ingredients CAS No Wt mg m Route Species Route Species Magnesite 1309 48 4 30 60 10 Not Available2. sparks and electrical shock See W117 2 At a minimum this includes welder s gloves and a protective face shield and may include arm protectors aprons hats shoulder protection as well as dark substantial clothing Train the welder not to permit electrically live parts or electrodes to contact skin or clothing or gloves if they are wet Insulate from work and ground isposal Information Discard any product residue disposable container or liner as ordinary waste in an environmentally acceptable manner according to Federal State and Local regulations unless otherwise noted No applicable ecological information available Section IX Emergency and First Aid Procedures Call for medical aid Employ first aid techniques recommended by the Canadian Red Cross IF BREATHING IS DIFFICULT give oxygen IF NOT BREATHING employ CPR Cardiopulmonary Resuscitation techniques INCASE OF ELECTRICAL SHOCK turn off power and follow recommended treatment In all cases call a physician
3. Not Available Aluminum oxide and or Bauxite 1344 28 1 10 30 10 Not Available Not Available Fluorides as F 7789 75 5 10 30 2 5 Sane Not Available Sf 590 g kg LDLo Mineral silicates 1332 58 7 10 30 5 oral rat reproductive Not Available Silicates and other binders 1344 09 8 5 10 10 eee Not Available Manganese and or manganese alloys and compounds as Mn 7439 96 5 1 5 0 2 ented e rE 50 mg kg LDL Nickel metal 7440 02 0 1 5 1 5 liiraverousineusah Not Available Silicon and or silicon alloys and compounds as Si 7440 21 3 0 1 1 10 Not Available Not Available Quartz 14808 60 7 0 1 1 0 05 EEEIEE eorn ahi Iron 7439 89 6 0 1 1 10 Not Available Not Available Crystalline Silica cristobalite 14464 46 1 0 1 1 0 025 a ei Not Available 10 mg kg LDLo 346 mg LCLo Vanadium alloys as V 7440 62 2 0 1 1 05 oral rat i i Notes LDLo LCLo Lowest published toxic concentration Not listed Nuisance value maximum is 10 milligrams per cubic Crystalline silica quartz is on the ARC International meter TLV value for iron oxide is 5 milligrams per cubic meter Agency for Research on Cancer and NTP National Toxicology Program lists as posing a carcinogenic risk to As respirable dust Value for respirable quartz is 0 1 milligrams humans per cubic meter As V205 fume or dust Section IV Physical Data Physical data such as odor vapor pressure density evaporation rate and freezing or boiling point
4. al Hygienists Effects of Overexposure Electric arc welding may create one or more of the following health hazards Fumes and Gases can be dangerous to your health Common entry is by inhalation Other possible routes are skin contact and ingestion Short term acute overexposure to welding fumes may result in discomfort such as metal fume fever dizziness nausea or dryness or irritation of nose throat or eyes May aggravate pre existing respiratory problems e g asthma emphysema Exposure to extremely high levels of fluorides can cause abdominal pain diarrhea muscular weakness and convulsions In extreme cases it can cause loss of consciousness and death Long term chronic overexposure to welding fumes can lead to siderosis iron deposits in lung and may affect pulmonary function Manganese overexposure can affect the central nervous system resulting in impaired speech and movement Bronchitis and some lung fibrosis have been reported Repeated exposure to fluorides may cause excessive calcification of the bone and calcification of ligaments of the ribs pelvis and spinal column May cause skin rash Nickel and its compounds are on the IARC International Agency for Research on Cancer and NTP National Toxicology Program lists as posing a cancer risk to humans Nickel compounds are skin sensitizers with symptoms usually occurring after repeated exposure ranging from a slight itch to severe dermatitis Overexposure to crystalline silica
5. l as the presence of contaminants in the atmosphere such as chlorinated hydrocarbon vapors from cleaning and degreasing activities When the electrode is consumed the fume and gas decomposition products generated are different in percent and form from the ingredients listed in Section III Decomposition products of normal operation include those originating from the volatilization reaction or oxidation of the materials shown in Section III plus those from the base metal and coating etc as noted above Reasonably expected fume constituents of this product would include Primarily iron oxide and fluorides secondarily complex oxides of aluminum calcium manganese nickel silicon and sodium when used with recommended Lincolnweld or Lincore electrodes See MSDS for electrode being used Maximum fume exposure guideline for this product based on manganese content is 4 0 milligrams per cubic meter Maximum respirable dust exposure guideline and PEL for this flux based on crystalline silica is 3 0 milligrams per cubic meter Handle to minimize generation of airborne dust Use adequate ventilation and dust collection Use respiratory protection if required to keep exposure below limits Gaseous reaction products may include carbon monoxide and carbon dioxide Ozone and nitrogen oxides may be formed by the radiation from the arc Determine the composition and quantity of fumes and gases to which workers are exposed by taking an air sample fr
6. om inside the welder s helmet if worn or in the worker s breathing zone Improve ventilation if exposures are not below limits See ANSI AWS F1 1 F1 2 F1 3 and F1 5 available from the American Welding Society 550 N W LeJeune Road Miami FL 33126 Section VIII Preventive Measures and Precautions for Safe Handling and Use Read and understand the manufacturer s instruction and the precautionary label on the product Request Lincoln Safety Publication E205 See Canadian Standards Association Standard CSA W117 2 Safety in Welding Cutting and Allied Processes published by the Canadian Standards Association 178 Rexdale Blvd Rexdale Ontario M9W1R3 for more details on many of the following Ventilation Use enough ventilation local exhaust at the arc or both to keep the fumes and gases from the worker s breathing zone and the general area Train the welder to keep his head out of the fumes Keep exposure as low as possible _Use adequate dust control measures Respiratory Protection Use respirable fume respirator or air supplied respirator when welding in confined space or general work area when local exhaust or ventilation does not keep exposure below TLV Eye Protection Wear helmet or use face shield with filter lens shade number or darker Shield others by providing screens and flash goggles No specific recommendation for submerged arc Protective Clothing Wear hand head and body protection which help to prevent injury from radiation
7. present in dust from this material can cause severe lung damage silicosis Respiratory overexposure to airborne crystalline silica is known to cause silicosis a form of disabling pulmonary fibrosis which can be progressive and may lead to death Crystalline silica is on the IARC International Agency for Research on Cancer and NTP National Toxicology Program lists as posing a cancer risk to humans Arc Rays can injure eyes and burn skin Skin cancer has been reported Electric Shock can kill If welding must be performed in damp locations or with wet clothing on metal structures or when in cramped positions such as sitting kneeling or lying or if there is a high risk of unavoidable or accidental contact with workpiece use the following equipment Semiautomatic DC Welder DC Manual Stick Welder or AC Welder with Reduced Voltage Control Section VII Reactivity Data Hazardous Decomposition Products Welding fumes and gases cannot be classified simply The composition and quantity of both are dependent upon the metal being welded the process procedure and electrodes used Other conditions which also influence the composition and quantity of the fumes and gases to which workers may be exposed include coatings on the metal being welded such as paint plating or galvanizing the number of welders and the volume of the worker area the quality and amount of ventilation the position of the welder s head with respect to the fume plume as wel
8. s are not listed as they are not applicable to this product and its use Section V Hazard Data Non Flammable Welding arc and sparks can ignite combustibles and flammable products See CSA W117 2 Section 9 7 as referenced in Section VIII Product is inert no special handling or spill procedures required Rev 9 07 CONTINUED ON SIDE TWO 4 Extreme Flammability 3 High Product MIL 800 HPNi Date 1 5 2009 1 Slight 0 Insignificant See Text Section VI Health Hazard Data and Toxicological Properties Acute Lethality Values LCs means the concentration of a substance in air that when administered by means of inhalation over a specified length of time in an animal assay is expected to cause the death of 50 of a defined animal population LDs means the single dose of a substance that when administered by a defined route in an animal assay is expected to cause the death of 50 of a defined animal population Threshold Limit Value The ACGIH recommended general limit for Welding Fume NOS Not Otherwise Specified is 5 mg m The TLV TWA is the time weighted average concentration for a normal 8 hour workday and a 40 hour workweek to which nearly all workers may be repeatedly exposed day after day without adverse effect See Section VII for specific fume constituents which may modify this TLV Threshold Limit Values are figures published by the American Conference of Government Industri
Download Pdf Manuals
Related Search