Lightolier 7226HRM User's Manual
Contents
1. E CONTINUED IV ATTACH MOUNTING RING e A RING into CEILING as shown ig H 1 In order to install SIDE MOUNTED type 2 MAX CEILING REFLECTOR TRIMS when the ceiling thickness THICKNESS is greater than 1 the additional ceiling material opposite the JUNCTION BOX must be removed Fig K 2 Insert REFLECTOR TRIM SOCKET CUP first into ceiling opening where the material was removed opposite the JUNCTION BOX Pivot the REFLECTOR TRIM and push it up into the ceiling Fig K CLIP ASSEMBLY Fig TO INSERT 1 Insert CLIP from inside housing through T slot 2 Apply downward force with screwdriver on top of CLIP or engage screwdriver in slot in CLIP s flange MOUNTING RING T SLOT FRAME SPRING FIG H INSIDE OF HOUSING STEP 1 3 Apply force until CLIP is snugly seated a SHORT HANDLE SCREWDRIVER CLIP REMOVAL Fig J STEP 2 4 Insert a small blade short handied screwdriver CEILING S through the CLIPS s screwdriver slot and press y against the opposite side of the CLIP A ara 2 Push CLIP up to top of T SLOT and remove N R CEILING V SNAP ON Fig E SEE SEPARATE REFLECTOR TRIM INSTRUCTION FIG SHEETS VI PUSH UP Fig F i JUNCTION BOX SOCKET CUP CEILING MATERIAL pi TO REMOVE REMOVED i E za ie J REMOVAL Wp eee y ili Ruane en f al Ss REFLECTOR a TRIM a FIG J FIG K WIRING DIAGRAM FOR 2 P2. IN BASE LAMP WIRING DIAGRAM FOR 4 PIN BASE LAMP za i Es ae 5 No owire wure SS wr p ien WHITE HOT U BLACK nc SCK E U BLACK r E ee T BALLAST CASE MUST BE GROUNDED cae BALLAST CASE asi BE GROUNDED WARNING USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER INC USE OF OTHER MANUFACTURERS REFLECTOR TRIMS VOIDS THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD
3. INSTRUCTION SHEET NO INSTALLATION OF PRE WIRED QUAD TUBE POWERSPEC ELECTRONIC COMPACT FLUORESCENT REMODELER KITS IS 12 26H RM 7218HT AND 7226HT SERIES 2 PIN QUAD TUBE edad H 7218HF AND 7226HF SERIES 4 PIN QUAD TUBE PRERA READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before installation To prevent electrical shock turn off electricity at fuse box before proceeding Retain these instructions for maintenance reference IMPORTANT SAFETY INSTRUCTIONS WARNING WHEN USING ELECTRICAL EQUIPMENT BASIC SAFETY PRECAUTIONS MUST ALWAYS BE OBSERVED INCLUDING THE FOLLOWING TO PREVENT ELECTRICAL SHOCK TURN OFF ELECTRICITY AT ELECTRICAL PANEL BEFORE PROCEEDING RISK OF ELECTRIC SHOCK TO PREVENT ELECTRIC SHOCK FOR PROPER OPERATION AND SAFETY THIS FIXTURE MUST BE GROUNDED THIS FIXTURE IS INTENDED FOR INSTALLATION IN ACCORDANCE WITH NATIONAL ELECTRIC CODE AND LOCAL REGULATIONS TURN OFF POWER BEFORE LAMPING AND RELAMPING Do not install fixture on a branch circuit having a Ground Fault Circuit Interrupter GFCI Typically electronic ballasts may cause GFCI tripping WARNING RISK OF FIRE DO NOT INSTALL INSULATION WITHIN 3 INCHES OF FIXTURE SIDES OR WIRING COMPARTMENT NOR ABOVE FIXTURE IN SUCH A MANNE
4. R TO ENTRAP HEAT EXISTING CONSTRUCTION FIG D FIG E FIG A FIG B FIG C FIG F I CUT OPENING il WIRE IN Ill ATTACH J BOX IV ATTACH V SNAP ON VI PUSH UP gt MOUNTING RING I CUT OPENING Fig A Use MOUNTING RING provided as a template to cut a hole in the ceiling Use inside diameter to cribe hole ot WIRE IN Fig B Cone A Wire to supply leads For Cable use built in Cable J BOX COVER a Clamp in J Box White fixture lead to neutral supply SPRING lead Black fixture lead to hot 120V supply lead BALLAST Bare fixture wire to supply ground Use wirenuts ASSEMBLY local hardware item Place all electrical connections in the J BOX Attach J BOX COVER onto J BOX ill ATTACH J BOX Fig C amp G NAIL CLIP auns J BOX PLATE 1 Attach J BOX PLATE to ceiling by pushing NAIL LONG LEG A RAISED BUMP TAB on J BOX PLATE into ceiling Fig G lt n Push LONG LEG of NAIL CLIPS supplied in parts bag into RAISED BUMP of J BOX PLATE NAIL GLIP gt and SHORT LEG into ceiling Fig G Make sure that the J BOX PLATE is securely EDGE OF CUT attached to the ceiling and the J BOX is in the OPENING IN CEILING position shown in Fig G l IGIIT Ol ij SECAUCUS NEW JERSEY 07096 a MONTREAL QUEBEC CANADA INSTALLATION OF PRE WIRED QUAD TUBE POWERSPEC 1S 7226HRM ELECTRONIC COMPACT FLUORESCENT REMODELER KITS R1293 7218HT AND 7226HT SERIES 2 PIN QUAD TUBE Page 2 of 2 7218HF AND 7226HF SERIES 4 PIN QUAD TUB
Download Pdf Manuals
Related Search