Lightolier IS-EC1 User's Manual
Contents
1. of Energos EC1 Lightolier is a Philips group brand 48 or 96 we Power Cord AC Supply Male Plug S R L Optional Cable Gripper Screw Do Not Over Tighten Figure 1 Cable Female Plug 10 32 Screw Figure 2 631 Airport Road Fall River MA 02720 e 508 679 8131 e Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2008 Philips Group B0608 PHILIPS LIGHTOLIEI Lighting Systems IS EC1 Page 3 of 5 Instruction Sheet for Assembly and Installation of Energos EC1 Step 1 Installing the Suspension Cables A B C D Install the power cable suspension assembly to the junction box Fig 1 Make sure to secure the green ground wire from Power Cord to the cross bar The first suspension in each row should be from the power feed end which contains a male power cord and an end cap Fig 1 Install the remaining cable suspension assemblies to the ceiling structure spaced at 48 or 96 apart as re quired Step 2 Installing the First Fixture nmo Orient fixture so female plug in fixture faces the power cord male plug Fig 2 Insert the Hanging Clips from first and second cable suspension assemblies into the fixture Fig 2 Connect the Power male cord plug into the first fixture female plug Hold the end cap flush with the end of the first fixture Tighten the 1 4 20 bolt and t2. LIGHTOLIEI Lighting Systems IS EC1 Page 1 of 5 Instruction Sheet for Assembly and Installation of Energos EC1 READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE PROCEEDING RETAIN THESE INSTRUCTIONS FOR MAINTENANCE REFERENCE This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before installation To prevent electrical shock turn off electricity at electrical panel before proceeding DO NOT INSTALL THIS SYSTEM IN A WET OR DAMP LOCATION DO NOT ENERGIZE ANYTHING OTHER THAN THE FIXTURES IN THE SYSTEM CONTRACTOR IS RESPONSIBLE FOR ADEQUATELY REINFORCING CEILING TO SUPPORT FIXTURE WEIGHT Fixtures in this system have a polarized male and female plugs at each end These plugs will snap together simply by pushing fixtures together OOO 631 Airport Road Fall River MA 02720 e 508 679 8131 e Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2008 Philips Group B0608 Lightolier is a Philips group brand PHILIPS LIGHTOLIER Page 2 of 5 48 or 96 fy gt Y eb Junction Box By Others 4 P os Canopy XN Power Cord a S R L Cord Optional P _ S R L Cord Optional Lighting Systems IS EC1 Instruction Sheet for Assembly and Installation
3. he 10 32 screw Fig 2 Level fixture lengthwise by pressing down on top of cable grippers and pushing or pulling on cables as required then cut excess cable If necessary level fixture widthwise by loosening the small screw at bottom of cable gripper and adjust sideways Be sure to re tighten screw Do not over tighten Step 3 Installing the Remaining Fixtures mop F Orient the next fixture s female plug so it faces the previous fixture s male plug Insert the Hanging Clips from second and third suspension assemblies into the second fixture Push fixtures together Tighten each of the 1 4 20 bolts in both fixtures Level fixture lengthwise by pressing down on top of cable grippers and pushing or pulling on cables as required then cut excess cable If necessary level fixture widthwise by loosening the small screw at bottom of cable gripper and adjust sideways Be sure to re tighten set screw Do not over tighten Repeat step 3 as many times as required to complete row Step 4 End of Row A B Hold the end cap flush with the last fixture in row Tighten the 1 4 20 bolts and 10 32 screw 631 Airport Road Fall River MA 02720 e 508 679 8131 Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2008 Philips Group B0608 Lightolier is a Philips group brand PHILIPS LIGHTOLIEI Lighting Systems IS EC1 Page 4 of 5 Instruction Sheet for Assembly and Installat
4. ing s electrical system RED from ECS100L to HOT from ECS POWER CORD Common White Common White Ground Green Hot Black Hot Black Ground Green 5 x 2 a bee Ground Green daz EE Building s Electrical System ECS100L Yellow Yellow Low Voltage S R L Low ECS Line Voltage Wiring Voltage Cord Power Cord Optional Wall Switch 2 Capable lt L O O O D gt EE Figure 5 o OA oL o 631 Airport Road Fall River MA 02720 e 508 679 8131 e Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2008 Philips Group B0608 Lightolier is a Philips group brand PHILIPS
5. ion of Energos EC1 Depending on voltage lamps and row length the need for additional Master units may arise Every time a new Master unit is required a new power drop must be made Since this new Master unit is not located at the beginning of run a minor modification must be made Step 1 Modifying Master Unit Remove reflector to gain access to Line Voltage splice compartment Remove 1 2 dia k o from reflector Cut the appropriate wires from wire harness and cap wires going to previous fixture See note below Tap appropriate wires from power cord into modified fixture s wire harness Route cord through hole in socket bracket then through reflector hole and finally through canopy Make all necessary connections at the ceiling box Continue attaching Slave fixtures until a new Master unit is required QnmMooODyD NOTE In some instances some of the wires in the fixture are required to remain uncut DALI SHARING DAYLIGHT SENSOR ETC In this case cut plug from secondary power cord and only cut and tap into the hot and neutral wires in the thru harness Power Cord 1st Power Drop Master Slave Slave Modified Master Slave Slave 96 96 96 96 96 48 Figure 3 631 Airport Road Fall River MA 02720 e 508 679 8131 e Fax 508 674 4710 We reserve the right to change details of design materials and finish www lightolier com 2008 Phili
6. ps Group B0608 Lightolier is a Philips group brand PHILIPS LIGHTOLIEI Lighting Systems IS EC1 Page 5 of 5 Instruction Sheet for Assembly and Installation of Energos EC1 Energos Control System fixtures may also be control with the ECS400T node switch or ECS100L power pack Installing the ECS400T Connect the low voltage wires coming from S R L cords as follows Fig 4 WHITE from low voltage wires to RELAY COMMON in ECS400T Ground BLACK from low voltage wires to COMMON in ECS400T einen Nie een RED from low voltage wires to 24V in ECS400T Ground Green Hot Black Wire a jumper in ECS400T between 24V and N O Ground Green Building s pans Electrical System Eom White Relay Common Installing the ECS100L The ECS100L may be installed in the wall or above ceiling line NOTE ONLY SLAVE FIXTURES ARE REQUIRED 000 Figure 4 LOW VOLTAGE Connect the low voltage wires coming from S R L cords as follows Fig 5 WHITE from low voltage wires to OCC SNS in ECS100L BLACK from low voltage wires to COMMON in ECS100L RED from low voltage wires to 24V in ECS100L LINE VOLTAGE WHITE from ECS100L to NEUTRAL from building s electrical system and COMMON from ECS POWER CORD BLACK from ECS100L to POWER from building s electrical system GREEN from ECS100L to GROUND from building s electrical system RED from ECS100L to POWER from build
Download Pdf Manuals
Related Search