Lightolier IS:48021 User's Manual
Contents
1. a L eae PROTECTIVE bs L BUSHING FRONT ALLEN COVER HEAD CONDUIT SCREWS PLATE BALLAST INTERNAL HOUSING TABS 2SLOTS gt BACK PLATE KNOCK OUT j HOLE DRYWALL D ANCHOR we r KNOCK OUT HOLE CONDUIT r PLATE m CONDUIT ALLEN HEAD SCREWS WIRE X z a NUTS J Figure 4 Lightolier a Genlyte Thomas Companywww lightolier com 631 Airport Road Fall River MA 02720 508 679 8131 Fax 508 674 4710 We reserve the right to change details of design materials and finish 2003 Genlyte Thomas Group LLC Lightolier Division A0403 PIOLFISOVT l2. terminal or ground lead Use WIRE NUTS 5 Carefully push connections back into the BALLAST HOUSING 6 Align tabs at top of BALLAST HOUSING with slots on BACK PLATE snap in and push housing flush with wall CAUTION MAKE CERTAIN THAT NO WIRES ARE PINCHED BETWEEN BACK PLATE AND FIXTURE BODY 7 Insert ALLEN HEAD SCREW provided into hole at bottom of BALLAST HOUSING and secure BALLAST HOUSING to BACK PLATE For DIFFUSER amp FRONT COVER attachment proceed as per Sections B amp C on first page of these instructions F 2 FOOT SOLI ELECTRICAL CONDUIT MOUNTING Note 2 foot version cannot be wired through the center hole but must use one of the KNOCK OUT HOLES Fig 4 1 Insert electrical conduit connector through CONDUIT PLATE supplied and secure with LOCK NUT by others 2 Select KNOCK OUT HOLE on BACK PLATE Pull supply wires through center hole in BACK PLATE Align BACK PLATE and mark holes for DRYWALL ANCHORS supplied screw DRYWALL ANCHORS into wall Proceed as per items 3 through 7 above For DIFFUSER amp FRONT COVER attachment proceed as per Sections B amp C on first page of these instructions Instruction Sheet Number 1S 48021 Page 2of2 For Assembly and Installation of Soli ADA Series Wall Ceiling Mounted T 5 Fluorescent INTERNAL BACK TABS PLATE 2 ae J BALLAST HOUSING a Figure 3 KNOCK OUT HOLE F DRYWALL ANCHOR WIRE NUTS CONDUIT
3. Instruction Sheet Number 1S 48021 Page 1 of 2 For Assembly and Installation of Soli ADA Series Wall Ceiling Mounted T 5 Fluorescent Read and understand these instructions before installing luminaire This luminaire is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before installation To prevent electrical shock turn off electricity at fuse box before proceeding Retain these instructions for maintenance reference A FOR OCTAGONAL OUTLET BOX J BOX GEM BOX OR SWITCH OUTLET BOX MOUNTING 1 Pull supply wires from OUTLET BOX through hole in MOUNTING PLATE Fig 1 Secure MOUNTING PLATE to OUTLET BOX using screws provided with OUTLET BOX 2 Insert tabs from OUTLET BOX COVERS into slots on MOUNTING PLATE to enclose OUTLET BOX 3 Pull supply wires through center hole in BACK PLATE Align BACK PLATE and mark holes for DRYWALL ANCHORS supplied screw DRYWALL ANCHORS into wall 4 Secure BACKPLATE to MOUNTING PLATE and DRYWALL ANCHORS using screws provided 5 While supporting BALLAST HOUSING Make electrical connections Black lead or lead without tracer marks to hot Black supply lead White lead or lead with tracer marks to neutral White supply lead Uninsulated wire is a ground wire and must be connected to grounding terminal or ground lead inside OUTLET BOX Use WIRE NUTS 6 Ca
4. oap and water N aad FOR ELECTRICAL CONDUIT MOUNTING see diagram and instructions on page two Figure 1 BALLAST y INTERNAL House Taps DIFFUSER Po i Jm 2SLOTS BACK PLATE ORYWALL ANCHOR OUTLET BOX COVERS wx ouTleT L MOUNTING BOX FRONT PROTECTIVE PLATE SCREWS COVER BUSHINGS WV aten PROVIDED an BY OTHERS SCREWS CUP INFRONT SNAP REAR PROTECTIVE BUSHING f INSTALLATION FOR a ACRYLIC DIFFUSER Figure 2 Lightolier a Genlyte Thomas Companywww lightolier com 631 Airport Road Fall River MA 02720 508 679 8131 Fax 508 674 4710 We reserve the right to change details of design materials and finish 2003 Genlyte Thomas Group LLC Lightolier Division A0403 PIOLFSOVIT elz E ELECTRICAL CONDUIT MOUNTING Fig 3 1 Insert electrical conduit connector through CONDUIT PLATE supplied and secure with LOCK NUT by others 2 Pull supply wires through center hole in BACK PLATE Align BACK PLATE and mark holes for DRYWALL ANCHORS supplied screw DRYWALL ANCHORS into wall 3 Secure BACKPLATE to CONDUIT PLATE and DRYWALL ANCHORS with screws provided 4 While supporting BALLAST HOUSING Make electrical connections Black lead or lead without tracer marks to hot Black supply lead White lead or lead with tracer marks to neutral White supply lead Uninsulated wire is a ground wire and must be connected to grounding
5. refully push connections back into the OUTLET BOX 7 Align tabs at top of BALLAST HOUSING with slots on BACK PLATE snap in and push housing flush with wall CAUTION MAKE CERTAIN THAT NO WIRES ARE PINCHED BETWEEN MOUNTING PLATE AND FIXTURE BODY 8 Insert ALLEN HEAD SCREW provided into hole at bottom of BALLAST HOUSING and fasten BALLAST HOUSING to BACK PLATE Fig 1 B FOR DIFFUSER ATTACHMENT Glass Diffuser Secure DIFFUSER to BALLAST HOUSING with Philips head glass mounting screws provided See Figs 1 amp 2 Acrylic Diffuser 1 Press PROTECTIVE BUSHINGS supplied through holes in ACRYLIC DIFFUSER 2 Proceed as above Glass Diffuser instructions NOTE If fixture is to be mounted without DIFFUSER insert gray plastic push in plugs supplied to cover glass mtg holes in BALLAST HOUSING C FOR FRONT COVER ATTACHMENT 1 After inserting Lamp Snap the FRONT COVER onto end caps of BALLAST HOUSING Fig 1 2 Insert ALLEN HEAD SCREWS into the holes at both ends of the fixture to secure front cover to BALLAST HOUSING D To remove glass acrylic for cleaning Remove FRONT COVER by unscrewing ALLEN HEAD SCREWS at both end caps and unsnap FRONT COVER from end caps Remove lamp by rotating 90 degrees and gently pulling it out of the sockets Unfasten DUFFUSER if used from the BALLAST HOUSING Glass clean with a small amount of glass cleaner on soft cloth to remove hand oils and dirt Acrylic clean with mild s
Download Pdf Manuals
Related Search