Lightolier IS:40421 User's Manual
Contents
1. White luminaire lead to neutral white POWERCORD lead Attach COLLAR bare copper ground wire attached to BOTTOM PLATE to green T ground wire from POWER CORD and BALLAST if supplied For metal halide luminaires refer to wiring diagram in Fig 4 LAMP CANOPY INSTALLATION AND HEIGHT ADJUSTMENTS AUXILIARY OPTION 1 Determine approximate overall height of luminaire If necessary cut excess POWERCORD Note Add a minimum of six inches to overall length determined for wiring into OUTLET BOX If POWERCORD has been shortened strip outside insulation back a minimum of six inches LIP Strip insulation on each conductor by approximately 3 8 2 Adjust the overall length of SUPPORT CABLE to approximately the eS FIG 3 same length as POWERCORD by pushing excess CABLE down into LENS CABLE ADJUSTER Caution make certain CABLE does not interfere REFLECTOR ONLY with internal wiring and components Fig 1 amp Fig 2 RING REFRACTOR Pass POWERCORD through hole in CANOPY Fig 1 Partially thread STUD into CROSSBAR gt Using appropriate slots in CROSSBAR secure CROSSBAR to OULTLET BOX using OUTLET BOX SCREWS provided with OUTLET BOX FIG 1 6 While supporting CANOPY ASSEMBLY make connections black ee PO2. CABLE FOAM ADJUSTER GASKET 2 Push any excess POWERCORD into hole in CANOPY secure POWERCORD in place by wrapping SNAP IN BUSHING around POWERCORD and push BUSHING into hole in CANOPY Fig 1 3 Reinstall DOOR and secure in place by tightening SCREW firmly onto MOUNTING PLATE Fig 1 4 Follow steps below for REFLECTOR REFRACTOR installation 5 Install recommended lamp s Note On metal halide luminaires with auxiliary lamp option install NECK halogen lamp as shown in Fig 3 CAUTION MAXIMUM WATTAGE AS MARKED ON LUMINAIRE MUST NOT BE EXCEEDED Tag E INSTALLATION SLOT Slide COLLAR up NECK Peel off backing from FOAM GASKET and adhere to TABS on REFLECTOR PLATE Fig 4 3 Tip REFLECTOR REFRACTOR over REFLECTOR PLATE and allow REFLECTOR REFRACTOR to rest on FOAM GASKET 4 Secure REFLECTORREFRACTOR in position by aligning SLOT in COLLAR over PINS and slide COLLAR down NECK Twist COLLAR counter clockwise allowing PINS to rest in NOTCHES Fig 5 COLLAR COLLAR PIN 12 REFRACTOR SUPPORT PLATE INSTALLATION Required for luminaires using 12 REFRACTORS only 1 Align SUPPPORT PLATE over SOCKET MOUNTING PLATE 2 Secure SUPPORT PLATE to SOCKET MOUNTING PLATE using two SCREWS provided with REFRACTOR Fig 7 LENS INSTALLATION WHEN PROVIDED 1 Place lens up into lip of REFLECTOR REFRACTOR Secure in place by expanding RING
3. READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE NSTRUCTION SHEET NO This luminaire is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before IS 4042 1 installation To prevent electric shock turn off electricity at fuse box before proceeding s Retain these instructions for maintenance reference C1101 Page 1 of 2 INSTRUCTION SHEET FOR ASSEMBLY AND INSTALLATION OF 12 amp 16 PENDALYTE SERIES WITH CORD AND CABLE Note This instruction sheet covers several luminaire styles OUTLET BOX Powerhead assembly lamp type and reflector system may Ara WIRE NUTS vary slightly from that shown but installation is the same g OA SUPPORT T D CROSSBAR CABLE POWER HEAD ASSEMBLY STUD Cee 1 Remove DOOR from POWERHEAD by loosening SCREW on top of da CANOPY KNURLED RING MOUNTING PLATE SCREW is located directly above PIN on a SN POWERHEAD DOOR which protrudes through BOTTOM PLATE SCREW Ss CABLE Pull DOOR directly away from POWERHEAD Fig 1 8 g ADJUSTER 2 Partially thread two SCREWS provided with SUSPENSION KIT into ADJUSTING POWERHEAD MOUNTING PLATE COLLAR POWERCORD 3 Thread CABLE ADJUSTER into SUPPORT PLATE and fully tighten ss a Fig 2 SNAP IN RIMP SNAP IN 4 Place POWERCORD down through hole in SUPPORT PLATE Note BUSHING BUSHING The en
4. WERCORD lead to hot supply lead white POWERCORD lead to ON ERC HAT neutral white supply lead Green POWERCORD lead is a ground wire 277V BLACK VOLTAGE and must be connected to grounding terminal or ground lead inside 240V eae OUTLET BOX Use WIRE NUTS local hardware item Push supply 208V wires and connections back into OUTLET BOX 120V WHITE s POWER 7 Place CANOPY over STUD and thread ADJUSTING COLLAR onto COMMO CORD STUD until CANOPY is fully secure against ceiling GROUND GROUND METAL HALIDE BALLAST CAUTION MAKE CERTAIN WIRES ARE NOT PINCHED W BETWEEN PARTS FIG 4 i er LIGHTOLIER M HToLien A imansricuss COMPANY INSTRUCTION SHEET NO READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE This luminaire is intended for installation in accordance with the National Electrical Code and local regulations IS 4042 1 To assure full compliance with local codes and regulations check with your local electrical inspector before installation To prevent electric shock turn off electricity at fuse box before proceeding C1101 Page 2 of 2 Retain these instructions for maintenance reference Min HEIGHT ADJUSTMENT AND INSTALLATION Adjust luminaire to final height To raise POWERHEAD push down on KNURLED RING on CABLE ADJUSTER and push SUPPORT CABLE into CABLE ADJUSTER To lower POWERHEAD push down on KNURLED RING on CABLE ADJUSTER and allow SUPPORT CABLE to come out of CABLE ADJUSTER Fully tighten KNURLED RING on
5. around outside lip of REFLECTOR REFRACTOR allowing spring tension of RING to close around lip Fig 1 SOCKET S LOUVER INSTALLATION when provided MOUNTING Hook J shaped end of SUPPORT SPRING through the two holes in SOCKET MOUNTING PLATE PLATE as shown in Fig 6 2 While carefully pulling down on SUPPORT SPRING hook V shaped end of SUPPORT SPRING through hole in CROSSBLADE LOUVER SOCKET 3 Carefully allow SUPPORT SPRING to pull CROSSBLADE LOUVER up into REFLECTOR making certain TABS on CROSSBLADE LOUVER sits securely into recessed LIP of REFLECTOR Fig 6 ye 7 SUPPORT PLATE MOUNTING al i SUPPORT PLATE a PLATE y m in SCREW lt Ay SUPPORT REFRACTOR SPRING it CROSSBLADE LOUVER i TAB FIG 7 FIG 6 i er LIGHTOLIER Monro ian A imansriouss COMPANY
6. d of POWERCORD with fiberglass sleeving and tape on each POWERCORD eer PLATE Note Allow at least six inches of POWERCORD inside PLATE POWERHEAD Fig 1 5 Loosen KNURLED RING on CABLE ADJUSTER Pass SUPPORT MOUNTING CABLE down into opening in top of CABLE ADJUSTER Note PLATE SUPPORT CABLE end without CRIMP should be placed into CABLE ADJUSTER Make certain ADJUSTING COLLAR has been placed up POWER TEAD A conductor should be placed inside the POWERHEAD Secure POWERCORD in place by wrapping SNAP IN BUSHING around SNAP IN eee POWERCORD and pushing BUSHING down into hole in SUPPORT BUSHING n SUPPORT KEYSLOT FIG 2 SCREW SUPPORT CABLE so CRIMP will go down into recessed portion of ADJUSTING COLLAR prior to passing SUPPORT CABLE into CABLE ADJUSTER Fig 1 amp Fig 2 6 Pass POWERCORD through hole in MOUNTING PLATE and align KEYSLOTS in SUPPORT PLATE with two SCREWS on top of MOUNTING PLATE Turn SUPPORT PLATE counter clockwise until NECK ze SCREWS are in the small slot area of the KEYSLOT Fully tighten SCREWS Fig 1 amp Fig 2 COELAN 7 Make wiring connections inside POWERHEAD using WIRE NUTS local hardware item Compact fluorescent and incandescent luminaires Black luminaire lead to hot black POWERCORD lead DOOR ee i BOTTOM COLLAR PLATE PIN
Download Pdf Manuals
Related Search