Lightolier IS:1155 User's Manual
Contents
1. INSTRUCTION SHEET NO INSTALLATION OF LYTECASTER REFLECTOR TRIM iS 1 1 5 5 IN THE 1100 SERIES FRAME IN KIT WITH ROTO CLIPS R0487 Q Ja READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE This fixture is intended for installation in accordance with the National Electrical Code and local or federal code specifications To prevent electrical shock turn off electricity at fuse box before proceeding NOTE Use this Instruction Sheet only when Lytecaster Trim is being installed in the 1100 series Frame in Kits with Roto Clips see Fig F if not disregard this instruction Sheet cco cs ow rn E y ott rare FIG A FIG B FIG C FIG D FIG E 1 FRAME IN 2 ROTATE CLIPS 3 SCREW IN 4 SNAP ON PUSH UP WARNING BEFORE INSTALLING REFLECTOR TRIM TO FRAME IN KIT READ MARKINGS IN REFLECTOR TRIM AND IN SOCKET CUP OF FRAME IN KIT TO DETERMINE LAMP WATTAGE AND TYPE APPLICABLE FOR YOUR INSTALLATION IF I C TYPE FRAMING KIT IS USED IT MAY BE INSTALLED IN DIRECT CONTACT WITH INSULATED CEILING IF A NON LC TYPE FRAME 4N KIT IS USED DO NOT INSTALL INSULATION WITHIN 3 INCHES OF FIXTURE SIDE OR WIRING COMPARTMENT NOR ABOVE FIXTURE IN SUCH A MANNER TO ENTRAP HEAT Er CUP 1 FRAME N Fig A a See Frame in Kit Instruction Sheets for installation procedure 2 ROTATE ROTO CLIPS Fig B gt N p SOCKET Rotate 4 ROTO CLIPS so that the short legs extend pores i EXTENSION inwardly toward the center opening Fig F2. i aS NOTE The SHORT LEG of the ROTO CLIP has NO SS FIG G return Gn top a 3 SCREW IN MALE ADAPTER Fig C Insert HOOK in ear of SPRING on SOCKET CUP and let HOUSING hang down Fig G Screw SOCKET EXTENSION MALE ADAPTER into SOCKET in SOCKET CUP 4 SNAP ON SOCKET CUP Fig D Disengage HOUSING from SOCKET CUP by pulling HOOK out of SPRING ear Fig H Insert SOCKET CUP between slots on MOUNTING BRACKET making sure SPRINGS snap into slots of MOUNTING BRACKET Fig 1 5 PUSH UP HOUSING Fig E Tilt HOUSING and insert SOCKET CUP into ceiling opening on opposite side of JUNCTION BOX Pivot housing and push it up into ceiling SOCKET CUP MOUNTING US PATENT NO 4 313 154 4 327 403 BRACKET FOREIGN PATENTS PENDING FOR OTHER REFLECTOR TRIMS Eyeball 1162 etc See back page g IG HTOI i b gt SECAUCUS NEW JERSEY 07094 0508 m d E E Bee E MONTREAL QUEBEC CANADA 15 1155 R0487 INSTALLATION OF ADJUSTABLE ACCENT LIGHT LOW VOLTAGE TRIM 6 Remove LAMPHOLDER RING from within HOUSING by pulling straight down and disengaging the LAMP SPRINGS which also act as a holding mechanism for LAMPHOLDER RING 7 Select voltage 12v 25 50 Watt or 5 5v 25 Watt depending on lamp being used by setting SLIDE SWITCH Fig J Insert screwdriver into slot and slide mmh aluan ameda r mm m m seml ian ma Le fe miadtalh if es sine switch if not already set according to lamp being used See Fi
3. ers or electronic dimmers intended for use with low voltage fixtures NOTE Low voltage fixtures may produce audible sound when used with external dimmers which may be objectional in acoustically critical areas HOUSING SLIDE SWITCH EYEBALL SUPPORT SPRING LAMP CONNECTOR LAMP LAMP SPRING APERTURE TRIM FIG L WARNING USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER INC USE OF OTHER MANUFACTURERS irr i TRIMS VOIDS THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE
4. g K 8 Install proper wattage PAR36 LAMP into LAMP CONNECTOR making certain the LAMP is seated all the way into the LAMP CONNECTOR 9 Insert LAMP into LAMPHOLDER RINGS so that face of LAMP is seated and extended through hole in the LAMPHOLDER RING and put the lamp and ring back into the LAMPHOLDER SUPPORT so that the LAMP SPRINGS now support aii SLIDE SWITCH LAMP HOLDER SUPPORT CONNEUIOR HOUSING LAMP LAMP SPRING 5 LAMPHOLDER 4 a Sa FIG J INSTALLATION OF EYEBALL LOW VOLTAGE TRIM 6 Remove APERTURE TRIM from within EYEBALL by ROPE ber eee down and disengaging from SUPPORT SPRINGS Fig L 7 Select voltage 12v 25 50 Watt or 5 5v 25 Watt depending on lamp being used by setting SLIDE SWITCH Fig L Insert screwdriver into slot and slide ranr rel lamn hoins switch if not already set according to lamp being used See Fig K 8 Install proper wattage PAR36 LAMP into LAMP CONNECTOR making certain the LAMP is seated all the way into the LAMP CONNECTOR Fig L 9 Insert LAMP into LAMP SPRING 10 Insert APERTURE TRIM and LAMP into EYEBALL until grooves on APERTURE TRIM engage into SLIDDODT CDDINGS Fim 1 oUrrYUn OFAN rig Lj NOTE LOW VOLTAGE FIXTURES should be dimmed only with special dimmers intended for that purpose Use Lightoller Precision LV Scenist or Lytemode or equivaient products by others or varlable auto transform
Download Pdf Manuals
Related Search