Lightolier IS:1152-A User's Manual
Contents
1. AL ADJUST LOCK SCREW Replace INSERTS CHY LAMP gt VERTICAL OXY ADJUST Lock 13 Insert PINHOLE FACEPLATE ewe by P LOCKING FIG K GUIDE RELAMPING The locking mechanisms in this fixture allow relamping without having to readjust and relock Follow Steps 7 10 and 13 NOTE 1 LOW VOLTAGE FIXTURES should be dimmed only with special dimmers intended specifically for that purpose Use Lightolier Lytemode Scenist Crescendo VA Neptune VA Precision VA Easyset VA Sunrise VA Radiant VA or equivalent products by others or variable auto transformers or electronic dimmers intended for use with low voltage fixtures 2 Low voltage fixtures may produce audible sound when used with dimmers which may be objectional In acoustically critical areas WARNING 1 LAMP MANUFACTURES REQUIRE THE GLASS LAMP GUARD BE IN PLACE BEFORE ENERGIZING LAMP AND THAT GREAT CARE MUST BE TAKEN THAT LAMP IS FULLY COOLED BEFORE RELAMPING AVOID FINGER MARKS ON INSIDE OF LAMP FOR THEY MAY CAUSE SHORT LAMP LIFE AND POSSIBLE BREAKAGE 2 USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER INC USE OF OTHER MANUFACTURER S REFLECTOR TRIMS VOIDS THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD2. Fig G Insert SOCKET CUP between tabs on MOUNTING BRACKET making sure noo snaps into slots of MOUNTING BRACKET Fig O 6 Tilt HOUSING and insert SOCKET CUP into ceiling opening on side opposite junction box pivot HOUSING and push it up into ceiling until flange on HOUSING is flush to ceiling Fig D U S PATENT NO 4 039 822 4 393 154 and 4 327 403 FOREIGN PATENTS PENDING WITH RETURN LONG LEG SHORT LEG Pa SHORT LEG SA Bice N A SS ROTO CLIP X 4 AROUND FIG E SEE BACK FOR LAMP INSTALLATION AND ADJUSTMENT LIGLTOLIER MONTREAL QUEBEC CANADA css g tT FIG C FIG D 3 SNAP ON 4 PUSH UP LONG LEG GREENFIELD Joa Sale z at HOUSING ie Z SOCKET CUP MALE ADAPTER MOUNTING ne BRACKET PIN HOLE FACE PLATE FIG G SOCKET CUP SPRING HOOK SECAUCUS NEW JERSEY 07096 r 11 1 LSE SCE RRL ee ee INSTALLATION OF LYTECASTER REFLECTOR TRIM 1S 1152 A 0690 IN THE 1102 FRAME IN KIT WITH ROTO CLIPS Page 2 of 2 TRIM INSTALLATION Cont d INSTALL LAMP NOTE Socket manufactures have suggested that socket may fall after 3 to 6 relampings If this occurs socket can be replaced by disconnecting male connectors attached to socket leads from female connectors attached to fixture leads and replacing it with a socket procured through Lightoller seo Fig I FIG 7 Remove LAMP RING from LAMP YOKE HO
3. INSTRUCTION SHEET NO IS 1152 A THIS REFLECTOR TRIM MUST BE INSTALLED IN LIGHTOLIER S 1102P1 FRAME IN KIT WITH ROTO CLIPS Page 1 of 2 READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before installation To prevent electrical shock turn off electricity at fuse box before proceeding Retain these Instructions for maintenance reference A GA FIG A FIG B 1 FRAME IN 2 ROTATE CLIPS WARNING RISK OF FIRE DO NOT INSTALL INSULATION WITHIN 3 INCHES OF FIXTURE SIDES OR WIRING COMPARTMENT NOR ABOVE FIXTURE IN SUCH A MANNER TO ENTRAP HEAT 1 FRAME IN Fig A See Frame In Kit Instruction Sheets S 1102 for M installation procedure 14 2 ROTATE ROTO CLIPS Fig B Rotate 4 ROTO CLIPS so that the short legs extend inwardly toward the center opening Fig F NOTE The SHORT LEG of the ROTO CLIP has NO return on top Fig E amp F TRIM INSTALLATION 3 Remove PINHOLE FACE PLATE from HOUSING by inserting fingers in aperture and pull apart from HOUSING Fig G 4 Insert HOOK in ear of SPRING on SOCKET CUP and let HOUSING hang down Fig H Screw SOCKET EXTENSION MALE ADAPTER into SOCKET in SOCKET CUP 5 Disengage HOUSING from SOCKET CUP by pulling HOOK out of SPRING ear
4. LDER by wa t pulling straight down Fig J LAMP YOKE HOLDER INSULATING SLEEVING MALE CONNECTORS _ Attached to Socket Wires FEMALE CONNECTORS Attached to Fixture Wires MR16 SOCKET 8 Insert LAMP MR 16 Bulb between LAMP SPRINGS until face of bulb sits firmly on GLASS LAMP GUARD Fig K 9 Attach SOCKET to bi pin prongs on LAMP Fig K NOTE No polarity of pins required LAMP 10 Insert LAMP RING with LAMP and GLASS LAMP E Pean OR GUARD attached back into LAMP YOKE HOLDER S kK Pe GLASS LAMP LAMP VERTICAL ANGLE ADJUSTMENT AND LOCK ae E HNS 11 Insert a screwdriver into the LOCKING GUIDE on the LAMP YOKE HOLDER and locate the slot in the FIG J VERTICAL ADJUST LOCK SCREW turn the SCREW i counterclockwise and using the screwdriver as a LAMP YOKE lever tilt the entire LAMP YOKE HOLDER to the HOLDER desired angle Once the desired angle is reached SUPPORT tighten screw by turning screwdriver clockwise until PLATE snug tight HORIZONTAL ADJUST AND LOCK 12 The entire LAMP YOKE HOLDER can be horizontally af rotated to aim the angle of light through the hole in the FACE PLATE TRIM Fig K This can be done by racking off the HORIZONTAL ADJUST LOCK SCREW one full turn freeing the SUPPORT PLATE Fig K atcusrv akc Grasping the YOKES on either side of the LAMP YOKE SCREW HOLDER rotate the SUPPORT PLATE to the desired angle and lock the position by tightening the HORIZONT
Download Pdf Manuals
Related Search